Home

theVSFX3 User`s Manual

1. Do not operate in excessive heat direct sunlight Be sure installation provides adequate ventilation Some system components can produce significant heat and must be properly installed to allow proper cooling and assure user safety All sides of the equipment must be clear of obstruction and allow free airflow There are no user serviceable parts inside Refer to qualified service personnel The socket outlet serving this unit must be installed near the equipment and be easily accessible 2 of 10 Pages 5400 Manual R1 6 doc 3 4 10 Compliance Certifications The VSFX3 is CE certified Standards Applied BS EN 60950 1 2002 incorporating Corrigendum No 1 and Amendment No 1 EN 55203 1 1996 EN 55203 2 1996 The VSFX3 is ETL Listed q The VSFX3 Conforms to UL STD 508A and is Certified to CAN CSA STD C22 2 c us NO 14 95 Listed Intertek 3 of 10 Pages 5400 Manual R1 6 doc 3 4 10 Introduction Thank you for selecting City Theatrical s VSFX3 Every effort has been made to anticipate your questions in this manual but if you have any questions that are not answered here or you want to discuss a special application please feel free to contact us directly at City Theatrical The VSFX3 developed in cooperation with White Light Ltd combines DMX512 control or stand alone operation with advanced motor control technology to provide quiet and smooth effect projection The VSFX3 uses an 18 dia glass image disk to proj
2. to the safety cable clip at the front of the VSFX3 and secure it to a suitable point S 4 Lamps When using the VSFX3 with a Source 4 Par MCM the fixture can be provided with either a 375W or 575W lamp Mounting on a Juliat 325 LFX 7 Install the Juliat 325 LFX adapter on the rear of the VSFX3 using the provide M5 hardware the Juliat 325 LFX adapter may already be factory installed if the unit was ordered that way 8 Mount the VSFX3 to the Juliat 325 LFX by sliding the adapter into the forward color frame slot on the Juliat 325 LFX 9 Slide the desired VSFX Lens Assembly into the Lens slot at the front of the VSFX3 Drive unit and secure it in position with the provided lens retaining spring 10 Rotate the VSFX3 to the position desired and lock into position using the locking screw at the top of the fixture adapter 11 Connect the safety cable to the safety cable clip at the front of the VSFX3 and secure it to a suitable point Using the VSFX3 with Other Lighting Fixtures The VSFX3 may be used with a lighting fixture other than the Source 4 Par MCM 575W max or the Juliat 325 LFX providing the disk or breakup temperature does not exceed 190 F 87 7 C Extended disk operating temperatures above 190 F 87 7 C may reduce disk life In addition the maximum allowable operating temperature of the electronics compartment is 104 F 40 C In any case the unit should not be used in any application that would result in an unsafe conditi
3. 400 Manual R1 6 doc 3 4 10 UNLESS EXCLUSIONS ARE SPECIFICALLY FORBIDDEN BY STATE LAW CITY THEATRICAL SHALL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR FAILURE OF THIS PRODUCT INCLUDING INJURY TO PERSONS OR PROPERTY 10 of 10 Pages 5400 Manual R1 6 doc 3 4 10
4. ART_ADDRESS SENSOR_DEFINITION SENSOR_VALUE IDENTIFY_DEVICE VSFX3 never stops In order to protect the glass disks from burning or other heat damage the VSFX3 moves in every speed setting When no DMX signal is present or if switches are set to 800 999 the unit defaults to half full speed Warranty City Theatrical Inc warrants to the original purchaser that the custom equipment offered will be free from defects in workmanship and material for a period of one year from date of purchase During the warranty period units will be repaired or replaced at the option of City Theatrical Inc The warranty does not extend to any parts of the unit that have been subjected to misuse or accident Neither does the warranty cover any machine that has been modified or repaired at other than an authorized repair station The warranty will not apply if procedures described in the Operations Manual are not followed This warranty does not include shipping to or from City Theatrical Inc Unless otherwise stipulated by state law all warranties expressed or implied are limited to the period of this warranty Customers requiring repair of their equipment should obtain an RGA from City Theatrical Equipment should be suitably packaged including a note with the owner s name and address and a description of the reason for return Ship package prepaid and insured City Theatrical cannot be responsible for loss or damage in shipment 9 of 10 Pages 5
5. CITY THEATRICAL NEW YORK LONDON The VSFX3 Image Effects Projector User s Manual Rev 1 6 2009 City Theatrical Inc City Theatrical developed the VSFX3 system in partnership with White Light Ltd of London The VSFX3 is a new version of the White Light VSFX System and it is compatible with the accessories for all previous versions of the VSFX and the Patt 252 effects LONDON OFFICE UNIT 1 3 WYVERN ESTATE BEVERLEY WAY CARLSTADT NEW JERSEY 07072 NEW MALDEN SURREY KT3 4PH TEL 800 230 9497 201 549 1160 TEL 44 0 20 8949 5051 FAX 201 549 1161 www citytheatrical com FAX 44 0 20 7183 6061 US HEADQUARTERS 475 BARELL AVENUE Contents Safety NOOO S a a t dass dice a ra a a aAa a aaan a aaaea aaa a cestuadecusedstubceusanisececceecetaceeecetudze Compliance Certification S sisisi iiaea iaasa dace iaaa e adadad asidini iaai PTHOCUCU OM ere EAE T E T E E E EEE SQUUD D E E E A AEE EEE TEE EE EEEE Using the VSFX3 with a Source 4 Par MOM cccssseeeeeeeseeeeeeeeneeeeeseeeeeeeseeeeeeeeesneeeenes S ITS L T E TTA A E LATS Mounting on a Juliat 325 LFX aannsssssnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn nnmnnn Using the VSFX3 with Other Lighting Fixtures ccccsssseeeeeseseeeeeeeeeeeeeseseeeeeesneeeenes Mains Connection issin siete A RR ER RR Re Installing REMOVING DISKS ccceeeeeeeeeeee esse ee eeeeeeeeeeee eee eeeaeeeseeeeeeeeeeseeeeaaeeeeeeeeesan
6. ect a wide range of effects including clouds rain flames snow water etc and is designed to be used with the ETC Source4 Par MCM not included Juliat 325 LFX not included or any suitable fixture Slot for optional Adjustable Light Mask Fixture Adapter Safety Cable ring Disk Case 496 Ope Disk Case Screw three total DMX Pass Thru Mains Power Inlet en Setup The VSFX3 can be used with an ETC Source 4 Par MCM or with a Juliat 325 LFX Each fixture requires a different adapter Each adapter is designed to allow rotation of the VSFX3 to achieve different angles of motion for the projected image Using the VSFX3 with a Source 4 Par MCM 1 Install the S4 Par adapter on the rear of the VSFX3 using the provided M5 hardware the S4 Par adapter may already be factory installed if the unit was ordered that way 2 Mount the VSFX3 to the Source 4 Par by sliding the adapter into the forward color frame slot on the S4 Par 3 Lower the Source 4 Par locking color frame latch into the slot provided on the VSFX3 S4 Par adapter to secure the VSFX3 in place 4 Slide the desired VSFX Lens Assembly into the Lens slot at the front of the VSFX3 Drive unit and secure it in position with the provided lens retaining spring 5 Rotate the VSFX3 to the position desired and lock into position using the locking screw at the top of the fixture adapter 4 of 10 Pages 5400 Manual R1 6 doc 3 4 10 6 Connect the safety cable
7. eesneeeeeees Shipping VSFX3 with DISKS sezccc 2ecececcteccdcceseadecagseacccegscaccesgseeccccedecadescurecusscedecccccdavteseceuedeeece Using the VSFX3 with Art Glass Breakups ccc cccssseeeeeeeseeeeeeeeeeeeeeseeeeeeeseeeeeeeeseneeeenes LONSGS isch dh ede RAK RAE Ae RNR RAE BEAR chan hana Using ETC Source 4 Lenses and the Lens Adapter ccs ecccssseeeeeseseeeeeseeeeeeeeesneenenes Adjustable Masking Shutter cccccecccscccesececesesscesecesececevanececevecniecesecetecereseuececesedeceievanecctezecaze Controls sci23 nisin REeAL LEER RERERERERERLEERE EM eaaa aaa are a ae aaa aa aaee riai Stand Alone Operation siaran ranana aranana aered a enades edadea doaa ko aaia Siida a diedana iniaiaiai DMX Operation ranieri neinar anaana aa adeo edda aaa Aeara eamat anara anaa e opaa e a adado ei aiee aai FIDM a A E A A EE EE E E DEA AET o oL EAA a EAT EE E TEE Warranty eiiiai sia eoio a a aeaa nae Safety Notices Please read this entire manual before using your new equipment Please keep the manual in a safe place so you can refer to it in the future as required The CTI VSFX3 is intended for use only by qualified professionals Connection installation and hanging of this equipment must be performed in accordance with all pertinent local regional and national safety codes and regulations The CTI VSFX3 is intended for indoor use only unless specified for outdoor use Keep the equipment dry Do not operate the equipment if it gets wet
8. ically for VSFX3 These three lenses match the original three White Light VSFX lenses which may also be used 1 Install the desired lens in the lens slot at the front of the unit 2 Secure with the safety retaining spring Using ETC Source 4 Lenses and the Lens Adapter ETC Source 4 Ellipsoidal lenses may also be used with VSFX3 when paired with the optional 5416 VSFX3 Source 4 Lens Adapter ETC S4 14 19 26 36 50 70 and 90 lens tubes can be used with the 5416 Lens adapter The S4 5 and 10 can also be used with the 5416 Lens Adapter in combination with the 5417 VSFX3 Long Lens Support To use a lens adapter 1 insert the desired lens adapter in the front or rear lens slot and secure with the retaining spring 2 Install the Source 4 ellipsoidal lens in the lens adapter and secure by installing the S4 lens thumb screws in the slots provided on the top and the bottom of the Lens Adapter 3 Focus the lens as required and lock into place with the S4 lens thumb screws An optional Donut Plate is provided with the CTI 5416 Lens Adapter This Donut Plate is recommended when ETC lenses are used to optimize the aperture of the VSFX3 To install mount the Donut Plate on the fixture adapter ring on the rear of the disk case using the 4 M3 PHP screws provided with the Donut Plate 7 of 10 Pages 5400 Manual R1 6 doc 3 4 10 When using the long S4 5 and 10 c with the 5422 Lens Adapter the 5417 Long lens support may be u
9. on Mains Connection The VSFX3 contains a universal power supply and so will operate with 100 240VAC 50 60Hz mains voltage and is fitted with an IEC C 14 mains inlet for power cable connection Units sold in the EU are provided with IEC C 13 to bare end power cables in standard EU color code Brown Hot Blue Neutral Yellow Green Earth Follow the color code when installing the desired connector for the locality where the VSFX3 is to be used Units sold in North America are provided With IEC C 13 to NEMA 5 15P Edison power cables Never power the VSFX3 from a dimmer Failure to ensure this may result in damage to the power supply motor and or control electronics which will not be covered under warranty The VSFX3 must always be running when the fixture is turned on Failure to ensure this may result in damage to the disk which will not be covered under warranty 5 of 10 Pages 5400 Manual R1 6 doc 3 4 10 Side Art Glass Clip Lower Art Glass Clip Glass Effect Disk Disk Lock Nut Rear Disk Case Cover removed Installing Removing Disks This operation should be performed with the VSFX3 drive unit lying face down on a suitable table or work bench 1 Open the cylindrical disk case by removing the three screws on the side of the case 2 Loosen and remove the locking nut at the center of the glass effect disk 3 Lift the glass disk out to remove Note the rubber disk under the glass disk 4 Install a new disk ove
10. r the rubber sleeved shaft Place the glass effect disk on top of the rubber disk noted above Replace and tighten the locking nut Reassemble the cylindrical disk case on Shipping VSFX3 with Disks Do not ship VSFX3 with a Disk installed The Disk may be damaged by vibration in shipment Remove the Disk prior to shipment and pack separately Using the VSFX3 with Art Glass Breakups Some of the effects incl Flame Smoke and Running Water use an art glass breakup in combination with the glass effect disk To install an art glass breakup 1 Remove the glass disk 2 Loosen the screws on the Lower Art Glass Retaining Clip and slide down 3 Slide the art glass breakup under the two Side Retaining Clips 4 Slide the Lower Art Glass Retaining Clip back up into position and secure in place Note The White Light plastic Breakup will fit in a VSFX3 however running temperatures in the unit when used with ETC Source 4 Par may exceed the usable limit 170 F 76 6 C of the White Light plastic Breakup so the WL Breakup is not recommended for use with a Source 4 Par The CTI 5421 Art Glass Breakup is made of glass and may be used with a Source 4 Par 6 of 10 Pages 5400 Manual R1 6 doc 3 4 10 Lenses The unit has two slots in the front The forward slot is for mounting a lens unit and the rear slot is for installing the optional adjustable light mask or color frame CTI manufactures a 6 5cm 90 10cm 50 and 15cm 30 lens specif
11. rt address 1 DMX slot controls direction with 0 through 49 for forward and 50 through 100 for reverse RDM Features VSFX3 is a fully enabled RDM Responder and all RDM commands and operations are available at anytime RDM functions supported include RDM Discovery Standard RDM Discovery function RDM Identify Status LED blinks Red Green and motor runs at full speed DMX Address control Setting of DMX address will succeed only when the DMX thumb wheels are set to 000 At all other times the request will receive a NACK response A read of the DMX address when the thumb wheels are at 000 will read the RDM set address at all other times it will read the value of the thumb wheels Driver fault Sensor Reports whether the driver is in a fault condition I E overload RPM Sensor Reports current speed in RPM mathematically 8 of 10 Pages 5400 Manual R1 6 doc 3 4 10 Select Preset Operation You can initiate the built in speed settings by using RDM presets The preset number is the same as the corresponding thumb wheel value For example to use RDM to call up thumb wheel setting 750 50 reverse direction issue a set preset 750 to the device BCD preset settings are ignored Supported RDM parameters DISC_UNIQUE_BRANCH DISC_MUTE DISC_UN_MUTE SUPPORTED_PARAMETERS PARAMETER_DESCRIPTION DEVICE_INFO PRODUCT_DETAIL_ID_LIST DEVICE_MODEL_DESCRIPTION MANUFACTURER_LABEL DEVICE_LABEL FACTORY_DEFAULTS SOFTWARE_VERSION_LABEL DMX_ST
12. sed to provide additional support for the lens Adjustable Masking Shutter The optional 5413 VSFX3 Adjustable Masking Shutter may be installed in the rear lens slot to mask the light beam of the VSFX3 To use the Masking Shutter adjust the leaves of the shutter as desired by manually sliding them and install the Shutter in the rear lens slot Controls Status LED The Bi color Status LED lights when mains power is connected It outputs the following colors and patterns to indicate operational status Blinking Red No DMX present Blinking Green DMX present Blinking Amber DMX received but address is out of range Rapidly flashing Red Noise and errors on DMX line Blinking Green at a rate which varies with motor Address 600 799 speed Address 800 999 Slow flash Amber Rotary Switches Three rotary BCD switches are provided for DMX addressing and Stand alone speed control Stand Alone Operation 1 Set the BCD Hundreds switch to 6 for forward operation 2 Set the tens and ones switch to any number from 0 99 to select the desired speed 3 Set the BCD Hundreds switch to 7 for reverse operation 4 Set the tens and ones switch to any number from 0 99 to select the desired speed DMX Operation 1 Set the desired DMX512 starting address using the rotary BCD switches i The Start address DMX slot controls rotation speed from slowest at 0 to fastest at 100 ii The Sta

theVSFX3 User`s Manual

Contents

Download Pdf Manuals

Related Search

Related Contents