Tribe Sub - Totem Acoustic
Contents
1. 1 Output speaker connections 5 way binding post terminals to connect to subwoofer module 2 Line in connectors Unbalanced signal input to accept signal from source 3 Line out connectors Unfiltered signal output to send source signal to additional sub amplifiers 4 Power switch Main power switch 5 AC power connector Removable power cord receptacle accepts both 120 v and 220 v voltage internally regulated 6 Fuse holder User replaceable Replace with same fuse rating 7 Model Select Model selection switch please place both toggles to appropriate model Tribe Sub Select model 8 TOTEM gt AMPLIFIER INSTALLATIO MOUNTING The amplifier is one rack unit high 1U and will fit into a standard EIA 19 rack Amplifiers should not be stacked directly on top of each other we recommend a space at least 3 in 7 62 cm for the top and sides with 5 in 12 7 cm on the back When shelf mounted the height of the supplied feet is adequate Rack mount tabs are included in the accessory package OPERATING VOLTAGE WARNING A label just above the mains cable connector on the rear of the amplifier indicates the AC mains voltage for which the amplifier is wired Connect the power cable only to the AC source referred to on the label The warranty will not cover damage caused by connecting to the wrong type of AC mains CONNECTIONS RCA Input Output Connections From an unbalanced source connect to the inp2. CAUTIO To prevent electrical shock do not use the electrical plug of your Totem Subwoofer with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent exposure To protect against the risk of electrical shock do not use near bathtubs sinks swimming pools saunas in wet basements near other water sources or rain If service is required please refer to your Totem Authorized Dealer AMPLIFIER MODULE CONTROLS Figure 1 Front Panel TRIBE amoiser 1 Input level attenuator This control is used to alter the signal level entering the amplifier or to cut down the unwanted noise from the input signal 2 Crossover frequency adjustment Continuously variable from 40Hz 120Hz to allow custom integration with any Totem loudspeaker Turning the dial completely to the right will bypass the crossover 3 Phase control Continuously variable from 0 180 to allow custom integration with mid high units in various installation positions 4 Crossover Bypass switch Allows the low pass crossover to be taken out of the circuit so an external crossover can be used 5 On Auto switch In the auto position the amplifier will go into sleep mode when there is no signal present for 20 30 minutes On position defeats the sleep mode 6 Power indicator This blue LED indicates that there is power present at the amp and that the rear mounted power switch is on Figure 2 Rear Panel
3. CONGRATULATIONS We sincerely thank you for having granted Totem the special place in your living environment These speakers are designed to redefine your musical understanding and open up corridors of new experiences We hope you not only enjoy but experience Totem as your guide to a new and rewarding listening environment You will without a doubt experience a Totem moment OUR VISION Totem Acoustics mission is to develop loudspeakers capable of reproducing a truly musical and involving performance Our goal is to provide designs that are both affordable and real soul movers for the music lover and surround lover Music of any period country or style is accurately and emotionally rendered with a powerful focus that is yet soul stirring Each speaker is a piece de resistance that attests to the profound sound staging that can be reproduced by flexible and innovative engineering Listen and believe TOTEM totemacoustic com 2 TOTEM TOTEM LIMITED WARRANTY ON SUBWOOFERS Please register online at www totemacoustic com within two weeks of the purchase date The Totem speakers must be purchased from a TOTEM AUTHORIZED DEALER Keep your original bill or receipt obtained from your Totem Authorized Dealer Retain the sturdy carton and all packing material if needed it will prove invaluable for damage free transport or storage All Totem products are created with the utmost care and quality in mind If ever
4. Amps FRONT PANEL Level Control Adjusts Input Signal Level Crossover Frequency Adjustment 40Hz 120Hz Phase Control 0 180 continuously variable Crossover Bypass Switch engages or disengages Low Pass Filter On Auto Switch On Continuous Sleep Mode Power On Indicator Blue LED REAR PANEL e Line In Connectors 1 Pair RCA Line Out Connectors 1 Pair RCA Output Connectors to Sub Module 1 Pair Binding Posts Mains Voltage Connector 100 120 V 220 230 V Auto Sensing Mains Voltage Fuse Holder T5AL 250 Volt REAR PANEL SWITCHES e Power Switch e Model Select Switch Tribe In wall Sub 8 select model 8 Tribe In wall Sub 12 select model 12 DIMENSIONS e Overall Dimensions incl Feet w x h xd 17 x 2 25 x 14 43 18 x 5 715 x 35 56 cm e Width with Rack Ears 19 48 26 cm WEIGHT e Net weight 6 8 kg 15 Ibs e Shipping weight 8 6 kg 19 Ibs 12
5. a problem should arise Totem s subwoofers are covered by a two 2 year limited warranty starting from the date of purchase The warranty applies to products in normal home use only The warranty is void if serial numbers have been altered or removed The warranty is void if products show signs of abuse The warranty is void if the subwoofer has been tampered with The subwoofer requires at least 85 100 hours of actual break in time period During this time refrain from playing the unit at very loud levels You will notice a definite gradual improvement as your unit breaks in Should servicing be required please contact your Totem Authorized Dealer We reserve the right to any future change or modification without notice If you have any further queries or require any classifications feel free to contact your Totem Authorized Dealer For further assistance contact your TOTEM AUTHORIZED DEALER or visit the Support Section of the Totem website at www totemacoustic com support TOTEM USER MANUAL TOTEM TRIBE SUB Congratulations on your new Totem Tribe Subwoofer A compact reference sub designed to seamlessly blend with your Totem speakers in any stereo or home theatre application Please take the time to fully read this manual prior to beginning set up The manual will clearly guide you to achieve the best possible sound that these newly acquired Totem speakers are capable of providing For further assistance contact our
6. tech support at info totemacoustic com UNPACKING Totem Acoustic keeps to a strict quality control regimen and all factory sealed products leave our facility in perfect condition If there are any damages visible or concealed that has occurred in handling it must be reported immediately to your Totem Authorized Dealer Carefully remove the speaker s from the box es take caution as the size often deceives the actual weight Save all custom cartons and packaging foam for future use They are rather expensive and may come in handy for future upgrades PRODUCT FEATURES SPECIFICATIONS Tribe Sub Discover the most innovative subwoofer ever Period With its sleek design and dazzling performance the Tribe Sub is filled with inner power Astonishingly high output levels and low frequency spectrum make the Tribe Sub awe inspiring Ultra flexible the Tribe Sub can be used in any direction horizontal vertical straight or flat This on wall beauty comes fully equipped with a stand to move it around and absorbent back feet to lay it on its back It can even be slipped under the couch Frequency response 26Hz 200Hz Driver compliment 2 x 8 active high current driver 250 500 watt bash Totem high current amplifier totemacoustic com 5 SAFETY INSTRUCTIONS f Y The lighting flash with arrowhead symbol within an equilateral CAUTION triangle is intended to alert the user to the presence of uninsulated RISK
7. OF ELECTRIC SHOCK dangerous voltage within the product s enclosure that may be of DO HOT OPEN sufficient magnitude to constitute a risk of electric shock to persons ATTENTION RISQUE DECHOC LECTRIQUE PAS OUVRIR The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 1 Read instructions all safety and operating instructions should be read before this unit is operated If you discover any damage please contact your retailer immediately 2 Follow instructions all operating and usage instructions should be followed 3 Heed Labels all labels on this system should be adhered to 4 Attachments do not use attachments not recommended by the product manufacturer as they may create hazard 5 Water and moisture do not let water or extreme moisture come in contact with this product Refrain from using the unit near any appliance that utilizes water or in any room that has excessive moisture 6 Heat ventilation This product should not be placed in built in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to The product should be situated away from heat sources such as radiators heat registers stoves and other products including amplifiers that produce heat 7 To protect the Totem Subwoo
8. ance the unit should be installed directly onto a wall stud close to the floor and a minimum of 12 30 48 cm from any side wall B With the Supplier Pedestal the Subwoofer may be installed in room both in a vertical and horizontal configuration In order to achieve maximum performance your subwoofer requires proper positioning We suggest experimenting with placement to achieve the best results C With the attached rubber dampers the Subwoofer may also be placed on its back The ultra low profile will allow for placement under furniture where room aesthetics is of the upmost importance OPERATION OPERATION PRECAUTIONS Make sure that the power switch is set to off before connecting any input or output or operating the switch on the rear panel Make sure that the AC mains voltage is correct and the same as the one printed on the rear panel of the amplifier Make sure that the switch on the rear panel for limiter function is in the correct position PROTECTION FEATURES LIMITER FUNCTION The limiter function is included to prevent dangerous clipped signals reaching the speaker and damaging it If an amplifier is severely overdriven the limiter will automatically lower the level of the subwoofer 11 TOTEM AMPLIFIER SPECS Maximum continuous power 500 watts Distortion lt 1 Maximum Rated Output Minimum Frequency Bandwidth 20Hz 500Hz no filters or EQ Input Impedance gt 20 kQ Current Draw at 4 Q 5
9. fer avoid microphone feedback continuous and excessive output from electronic musical instruments or excessive signal distortion 8 Power sources this product should be operated only from the type of power source indicated on the marking label If you are not sure of the type of the power supply of your home consult your product dealer or your local power company 9 Ground or polarization this product may be equipped with a polarized alternating current line plug a plug having one blade wider than the other this plug will fit into the power outlet only one way This is a safety feature If you are unable to insert the plug fully into the outlet try reversing the plug If the plug should still fail to fit contact your electrician to replace your obsolete outlet Do not defeat the safety purpose of the polarized plug 10 Power cord protection the power supply cord should be routed so that they are not likely to be walked on or pinched by items placed upon or against them paying particular attention to cords at the plugs convenience receptacles and at the point where they exit from the product 11 Overloading do not over load wall outlet extension cords or integral convenience receptacles as this can result in a risk of fire or electrical shock 12 Objects and liquid entry never push objects of any kind into the product through openings as the may touch dangerous voltage points or short out parts that could result in a fire or elect
10. rical shock never spill liquid of any kind on the product 13 Cleaning unplug the product from the wall outlet before cleaning Do not use liquid cleaners or aerosol cleaners If necessary use a damp cloth for cleaning TOTEM gt 14 Service do not attempt to service this product yourself Opening or removing covers may expose you to dangerous voltages or other hazards Refer all servicing to qualified service personnel 15 Damage requiring service unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions if the power supply cord or plug is damaged if liquid has been spilled or objects have fallen into the product if the product has been exposed to rain or water if the product does not operate normally by following operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation e if the product has been dropped or damaged in any way e if the product exhibits a distinct change in performance despite verifying that all system connections are correct Replacement parts If replacement parts are required be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part unauthorized substitutions may result in fire electric shock or other hazards
11. ut of the Totem in wall amplifier For a mono LFE signal only the right or left input needs to be occupied In a 2 channel stereo application both the right and left input are to be connected To incorporate a second in wall subwoofer simply connect an additional RCA cable from the output of the first amplifier to the input of the second amplifier Connecting the Tribe Subwoofer Module The Subwoofer module connections is made via the 2 gold plated binding posts When connecting 1 subwoofer to the amplifier the wire connects to the RED binding post The wire connects to the BLACK binding post The TOTEM Tribe amplifier can accept 2 x TOTEM TRIBE SUB The units are only to be connected in parallel Both wire are to be connect to the RED binding post of the amplifier and both wire connect to the BLACK binding post of the amplifier Do NOT connect multiple subwoofers in series Never connect either output terminal to ground or to some other output or input terminal Pay careful attention to speaker polarity loudspeakers connected out of polarity degrade sound quality and may be damaged as a consequence 10 TOTEM gt INSTALLING THE TRIBE SUB The Tribe Sub is an extremely flexible unit that may be installed in three different configurations A The Totem Sub may be installed on the wall with the included wall brackets and templates Locate the final placement for the enclosure For maximum perform
Download Pdf Manuals
Related Search