quick installation guide
Contents
1. TCP IP max 90m RS 485 1 km max 32 Units EWS and Biometric Readers E 9 2 A U 0 4 4 4 CA KAA AAA ANA AAA AAS RS485 USB Converter RS485 tuning Jumper for RS485 termination Put the jumper 1200hm in closed position on the first and the last controller on a RS485 network PG TCP IP RS485 1 km max 32 Units EWS and Biometric Readers IMPORTANT NOTE The RS485 Communication Line must be made in daisy chain NOT in a star type configuration The cable must be twisted and shielded If the shield is used connect the EARTH from ONE side of the RS 485 Line to the shield cable Connect the ground of each unit in the RS 485 Line using a third wire in the same cable RS485 Termination resistors Terminate both ends of the line with 120 Ohm resistor If end of line is EWS use built in resistor 120 ohm by closing the jumper If the communication is not established and stable use the external resistors provided in the hardware kit When using CAT 5 compatible cable in most of the cases termination made with 50 Ohm external resistor or combination of 50 Ohm external and termination resistor from the EWS 120 Ohm should be the solution2. EWS 2 door access control unit Quick Installation Guide for EWS ver 3 5 Complete user manual and software supplied on the CD R provided or on www visual plus com Contact with external tension 5 TN Exit Button NO mechanical or relay dry contact Door Sensor NC mechanical or relay dry contact EWS PCB ver 3 5 Specifications Power Supply User Capacity Event capacity Communication Controllers per system Door relays Programmable Outputs Readers Programmable Inputs Door sensors Exit Button Inputs Wiegand interface Entry Mode Environment temperature Humidity Tamper Consumption Installation Dry hg contact 12V dut Dral I r PE 12Vdc Out Z d 2 ai 2 T r 3 i Sa Free inputs Q i 1K Iz i Im S ay S S Electro Magnetic P if if 2 tock Sen 1K aoa a Ta EE C H KPY DO Fuse ondi2V RS485 eae Electric Door Strike Reset IP AC powered Battery press and hold for 3sec to reset the IP CR2032 the port and the network password L m ou IP 192 168 1 100 a 4001 Electric Door Strike e _ Alpi ime LD19 a LD1 A ie m DC powered Ko com Se ee es a en E e porch p Ss red white yellow max 50 m O oO lO xT cole BOS FS opty CGH J a o gt a 22 OSS Jumper BIOC MINI M 11 15VDC max 15000 max 30000 TCP IP or
3. RS485 unlimited 2 250 VAC 10A 2 250 VAC 10A 2 2 5 30VDC 3 28mA 2 2 26bit 34bit or customizable 8 to 128bit Card PIN Finger Card or and PIN Card or and Finger PIN or and Finger Finger on Card 0 45 C 0 80 non condensing Yes 300 mA without readers 1 Insert the battery provided with the hardware kit 2 Connect the devices according to the connection diagram above 3 Use the provided 1K resistors for the Door Sensors and Push Buttons 4 Use the diodes provided when the door lock is DC powered or the capacitor 10K resistor when the lock is AC powered 5 Use the provided resistors for RS485 tuning Instructions 1 Keep the distance reader to controller less than 50 meters 2 Always use twisted pair cables when wiring a RS485 network biometric readers or EWS controllers 3 Do not use twisted pair cables for the Wiegand wires DO and D1 4 Always keep the RS485 line in daisy chain 5 Make sure that the terminal block is correctly inserted make sure that is not shifted left right by one position and see if the wires are not put in reverse order 6 Do not swap the RS485 terminal with the power supply terminal 7 All the controllers that are communicating via TCP IP must have different IP address Communication PROS Software TCP IP Switch Router TCP IP max 90m Mn ie Sian fT ie te TID ew 5 Serial RS485 PROS Software pra ereares USB CCOCC0E
Download Pdf Manuals
Related Search