User Manual - American Industrial Systems, Inc.
Contents
1. 7 oS visualization re envisioned User Guide PCT Multi Touch Monitor Display DTR19T100 A1 PCT The information contained in this document is subject to change without notice This document contains proprietary information that is protected by copyright 2013 American Industrial Systems All rights are reserved No part of this document may be reproduced translated to another language or stored in a retrieval system or transmitted by any means electronic mechanical photocopying recording or otherwise without prior written permission Windows is a registered trademark of Microsoft Inc Other brand or product names are trademarks of their respective holders American Industrial Systems Inc http www aispro com The test results show that this device meets the FCC rules Those limits are set to protect residential areas from the devices with harmful emission This device will produce use and radiate radio frequency energy In addition failure to follow the user s manual to install or use this device might produce harmful interference with radio communication Notwithstanding the foregoing it does not guarantee that this type of harmful interference does not occur in some special installations The interference caused by this device to the reception of radio or television signals may be verified by turning it on and off Any changes or modifications to this TFT LCD would void the user s authority to operate this device Im2. OSD Menu ITEM CONTENT Contrast The monitor luminance level control Brightness The monitor backlight level control Auto Adjust Fine tune the image to full screen automatically Left Right Moving screen image honzontal position to left or right Up Down Moving screen image vertical position to up or down Horizontal size The screen image horizontal dot clock adjustment Fine The screen image pixel phase adjustment OSD Left Right Moving OSD menu honzontal position to left or right OSD Up Down Moving OSD menu vertical position to up or down OSD Time out OSD auto disappear time selection OSD menu language selection English French Japa OSD Language nese Deutsch Spanish Italian Traditional Chinese and Simplified Chinese Factory Reset Factory default value restored Color temperature selection 9300K 6500K 5500K an 7500K User Volume Audio model only Audio volume adjustment Mute Audio model only Audio On Off control American Industrial Systems DTR19T100 A1 PCT User Guide Page 16 Appendix Troubleshooting If you are experiencing trouble with the LCD display refer to the following If the problem persists please contact your local dealer or our service center Problem No image appears on screen e Check that all the I O and power connectors are correctly and well connected as described in the Installation section e Make sure the pins of the connectors are not crooked or broken Problem Par
3. Screen Driver Installation The monitor is available with USB connection The Linux kernel 2 6 x 32 bit amp 64 bit touch driver is located on the enclosed CD ROM HID for Windows 7 VISTA XP 2000 ME 98 Please Note The system requires 15 seconds for Windows 7 to install uninstall the touch drivers while turning power on off or plugging unplugging USB cable Driver Install Instructions If you are using a PC running driver Linux kernel 2 6 x 32 bit amp 64 bit follow the instructions below 1 Power on the PC 2 Be sure the USB cable is connected from the PC to the LCD display 3 Open the CD ROM 4 Follow the step by step instructions as shown on the pop up windows If you are using a PC running Windows XP Embedded follow the instructions below Express Power on the computer Make sure that the USB cable is connected to the computer Be sure that your EWF is disabled If your EWF is enabled please disable the EWF by using the EWF Manager command 4 Once the EWF is disabled click on the XP driver on the CD ROM and follow the step by step instructions as shown on the pop up windows Custom 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Follow the step by step instructions found in the folder fi le on the CD ROM If you are using a PC running Windows CE follow the instructions below Power on the computer Make sure that the USB cable is connected to th
4. ard Check all the power switches power cables and VGA DVI signal cable Going to Sleep The LCD display is under the power saving mode In addition the LCD display will enter power saving mode when experiencing a sudden signal disconnecting problem The monitor can be activated by pressing any keyboard triggering the mouse or touching the screen Out of Range This message means that the signal of the computer graphic card is not compatible with the LCD display When the signal is not included in the Video Modes list we have listed in the Appendices of this manual the LCD monitor will display this message American Industrial Systems DTR19T100 A1 PCT User Guide Page 18 Product Dimension gt Front View gt Side View gt Top View American Industrial Systems DTR19T100 A1 PCT User Guide Page 19 Compatibility Modes Mode Resolution H Frequency KHz V Frequency Hz IBM VGA 720X400 31 47 70 IBM VGA 640X480 31 47 Apple Macll 640X480 35 00 VESA VGA 640X480 37 86 72 VESA VGA 640X480 37 50 75 VESA VGA 800X600 35 16 VESA VGA 800X600 37 88 VESA VGA 800X600 48 08 72 VESA VGA 800X600 46 88 75 Apple Mac 832X624 49 72 75 VESA XGA 1024X768 48 36 60 VESA XGA 1024X768 56 48 70 VESA XGA 1024X768 60 02 75 VESA SXGA 1280X1024 64 00 60 VESA SXGA 1280X1024 80 00 75 VESA SXGA 1152X864 67 50 75 VESA SXGA 1280X960 60 00 60 American Industrial Systems DTR19T100 A1 PCT User Guide Page 20 Touch
5. direct sunlight American Industrial Systems DTR19T100 A1 PCT User Guide Page 4 Introduction About DTR19T100 A1 PCT DT Desk Top R Regular width ratio of 4 3 19 Diagonal viewing area in inches PCT Projected Capacitive Touch The monitor has a flat panel screen with an active matrix thin film transistor TFT liquid crystal display LCD Features include e Direct Analog signal input e Active matrix TFT LCD technology e 1280 x 1024 SXGA resolution e 19 viewable display area e 31 47 80 KHz horizontal scan e 56 75 Hz high refresh rate e 0 294mm x 0 294mm pixel pitch e Auto adjustment function e Multilingual OSD user control e Kensington security slot e 100 mm VESA mount e Removable base for flexible mounting solutions e Projected Capacitive touch screen with USB controller American Industrial Systems DTR19T100 A1 PCT User Guide Page 5 Touch Screen for DTR19T100 A1 PCT e Projected capacitive touch screen for finger input only e Surface Glare treatment e Interface USB controller e Transmittance 90 5 e HID Windows 7 e Driver VISTA XP 2000 CE XP Embedded Linux Apple Mac OS American Industrial Systems DTR19T100 A1 PCT User Guide Page 6 Package Overview LCD Display Power Cord VGA Signal Cable 0 USB Cable A to B RS 232 Cable Touch Dnver CD for combo model only Quick Start Guide Screw American Industrial Systems DTR19T100 A1 PCT User Gu
6. e computer 3 Using Platform Builder build an image fi le by following the step by step instructions found in the folder fi le on the CD ROM American Industrial Systems DTR19T100 A1 PCT User Guide Page 21 If you are using a PC running Linux or Apple Mac OS follow the instructions below 1 Power on the computer 2 Make sure that the USB cable is connected to the computer 3 Follow the step by step instructions found in the folder fi le on the CD ROM American Industrial Systems DTR19T100 A1 PCT User Guide Page 22
7. eesaaeeeeeecesseceeaaeeeesessseessaaeeeeeeesess 16 APPENDIX sciare e oa iia 17 O 17 Warning A on ones dy vs as yousedeada ss a a ea Eae Raina Eaa 18 Product DIMENSION uns esa 19 Compatibility Modest is 20 Touch Screen Driver Installation siecia dpi eaire aE iaei Ei 21 American Industrial Systems DTR19T100 A1 PCT User Guide Page 3 Usage Notice A Warning To prevent the risk of fire or shock hazards do not expose this product to rain or moisture Do not open or disassemble the product as this may cause electrical shock Precautions Follow all warnings precautions and maintenance as recommended in this user s manual to maximize the life of your unit Do e Turn off the product before cleaning e Touch screen surface may be cleaned using a soft clean cloth moistened with mild window glass commercial cleaners or 50 50 mixture of water and isopropyl alcohol e Usea soft cloth moistened with mild detergent to clean the display housing e Disconnect the power plug from AC outlet if the product is not going to be used for an extended period of time Don t e Do not touch the LCD Display screen surface with sharp or hard objects e Do not use abrasive cleaners waxes or solvents for your cleaning e Do not operate the product under the following conditions Extremely hot cold or humid environment Areas susceptible to excessive dust and dirt Near any appliance generating a strong magnetic field In
8. ics card to make it less than or equal to 1280 x 1024 resolution and make sure the timing of the display mode is compatible with the LCD display We have listed the compatible Video Modes of your LCD display in the appendix on page 16 for your reference American Industrial Systems DTR19T100 A1 PCT User Guide Page 12 Remove the Deskstand Remove 4 screws and then remove hinge American Industrial Systems DTR19T100 A1 PCT User Guide Page 13 User Controls Side Panel Controls Key Name EJ Brightness Main item select up Adjust up cn Wanton ow a om e Enter Select sub item function Power On Off American Industrial Systems DTR19T100 A1 PCT User Guide Page 14 How to Use the OSD Menus 1 De oP 0 9 Press the MENU button to pop up the on screen menu and press Up or Down button to select among the five functions in the main menus Choose the adjustment items by pressing the Enter button Adjust the value of the adjustment items by pressing the Up or Down button With the OSD menu on screen press Menu button to return main menu or exit OSD The OSD menu will automatically close if you have left it idle for a pre set time To Lock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press Menu key the OSD menu will pops upon displa
9. ide Page 7 Installation Product Overview Front View Bottom View American Industrial Systems DTR19T100 A1 PCT User Guide Page 8 Kensington Security Slot The monitor can be secured to your desk or any other fixed object with Kensington lock security products The Kensington lock is not included American Industrial Systems DTR19T100 A1 PCT User Guide Page 9 VESA Mount for Your Monitor This monitor conforms to the VESA Flat Panel Mounting Physical Mounting Interface standard which defines a physical mounting interface for flat panel monitors and corresponding with the standards of flat panel monitor mounting devices such as wall and table arms The VESA mounting interface is located on the back of your monitor To mount the monitor on an UL listed certified swing arm or other mounting fixture follow the instructions included with the mounting fixture to be used 100 0 Slots x4 VESA Mounting Interface A Warning Please select the proper screws The distance between the back cover surface and the bottom of the screw hole is 11 mm Please use four M4 screws diameter with proper length to mount your monitor Please note the mounting stand must be able to support at least 11 Ibs 5Kg American Industrial Systems DTR19T100 A1 PCT User Guide Page 10 Start Your Installation Please follow these instructions so that you can hookup the cables to associated connector Lay the LCD fla
10. portant Recycle Instruction Lamp s inside this product contains mercury This product may contain other electronic waste that can be hazardous if not disposed of properly Recycle or dispose in accordance with local state or federal Laws For more information contact the Electronic Industries Alliance at WWW EIAE ORG For lamp specific disposal information check WWW LAMPRECYCLE ORG American Industrial Systems DTR19T100 A1 PCT User Guide Page 2 Table of Contents troduction ad ide its li 5 E a cccccssscsecssssceutenstscdensas cuveanincecanedaceeanevanduevendcueval a eaa E EEEE aaa aaner 5 Touch Screen for DIRIITIOOALPCI cocinando 6 Package OVEIVIEW idol 7 A iin aenn a aa a ea a a Eaa a E eaaa aE E Ea a aana 8 Product OVe Vi Wisin a e acti 8 Front Wii deiad 8 BOOM VIEW iia A c 8 SAA sisssccssisccccessseccvessessccusssscvetaaaaccccbspuvctevasvacenasvacicdaabasccchasuctevsssacevassseterespascecsanaetes 9 VESA Mount for Your MOnitor c ccecceesceescesscecececeeeeneeeneeeaeeeaeeseneceaeeeaeesaeceaeseaeesseesseeeeaeeeaeesaeseaeeeaeeseetes 10 Start Your nstallatin sessen aaa eee beens ce E E anata EE OEE OE a 11 Connecting the DisplaYV iii ta ii 12 Remove the Deskstanid iia ais cnica 13 UserContrdl Sancti ssl ale iia calisa 14 Side Panel Controls venia a iaa 14 How to Use the OSD Menus sirrinin eannan a a aa r eaea a ea OaE E Eg 15 On Screen Display M NusS csssscccccceccsssssssseeeccsssessssseeeeceesessessaeeeecesee
11. t on an even surface Move the stand into position as seen in the step 2 diagram Remove the cable cover as seen in the step 3 diagram Pee Ne Connect the cables to the appropriate connectors as seen in the step 4 diagram Use step 4 1 diagram if using the RS 232 serial connector Use the step 4 2 diagram if using the USB connector 5 Position all cables under the cover lip as seen in the step 5 diagram 6 Re attach the cable cover Remove the screw CBM M3x6 from the accessory box and insert the screw into the cable cover and monitor as seen in the step 5 diagram American Industrial Systems DTR19T100 A1 PCT User Guide Page 11 Connecting the Display To setup this display please refer to the following figure and procedures Be sure all equipment is turned off Connect the AC power cord to the power connector on the monitor and the other end into an electrical outlet 3 Connect the D SUB cable from the display s VGA input connector to the D SUB connector of your host computer and tighten the screws 4 Connect the RS 232 or USB cable from the RS 232 or USB port of your display to the RS 232 port or USB port of your computer 5 Configure the touch screen Refer to the Touch Screen Driver Installation section on page 21 6 Once the touch screen is configured the monitor is ready for use A Notice To ensure the LCD display works well with your computer please configure the display mode of your graph
12. tial Image or incorrectly displayed image e Check to see if the resolution of your computer is higher than that of the LCD display e Reconfigure the resolution of your computer to make it less than or equal to 1280 x 1024 Problem Image has vertical flickering line bars e Use Fine to make an adjustment e Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display Problem Image is unstable and flickering e Use Fine to make an adjustment Problem Image is scrolling e Check and make sure the VGA signal cable or adapter is securely connected e Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD display Problem Vague image characters and graphics e Use Fine to make an adjustment If this problem persists use Horizontal size to make an adjustment American Industrial Systems DTR19T100 A1 PCT User Guide Page 17 Warning Signal If you see warning messages on your LCD screen this means that the LCD display cannot receive a clean signal from the computer graphics card Below are the three kinds of Warning Signal Please check the cable connections or contact your local dealer or our service center for more information No Signal This message means that the LCD display has been powered on but it cannot receive any signal from the computer graphics c
13. y b Press and hold the Menu key again with the OSD menu on the screen the OSD menu will disappear Then press the Power key 1 time while the menu key is still being pressed The Lock Unlock menu will appear for 3 seconds c Use the Enter key to select OSD or Power setting then set at Lock by pushing the UP or Down button d When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically 7 To Unlock the OSD Power menu buttons please follow the instructions below Please note the monitor has to be turned ON with a valid signal pre set a Press and hold the Menu key then press the Power key simultaneously the Lock Unlock menu will appear for 3 seconds b Use the Enter key to select OSD or Power setting then set at Unlock by pushing the UP or Down button c When the UP or Down button is released the previous setting will be saved and exit the Lock Unlock menu automatically Please note a When the OSD Lock function is selected this indicates that all the buttons except power button are now disabled b When the Power Lock function is selected this indicates that the power key is disabled user can not to turn off the monitor by Power key American Industrial Systems DTR19T100 A1 PCT User Guide Page 15 On Screen Display Menus Main
Download Pdf Manuals
Related Search