Set up the Audio Sensor Introduction Program the
Contents
1. be the main power 9V alkaline battery will become the backup power supply 2 Turn on the unit to test mode by sliding the ON OFF TEST switch to TEST The red light indicator will flash once you turn on the unit 3 Allow 15 seconds for the sensor to warm up 4 Rotate the Volume to LO 5 If the light indicator on the AS 433 turns on as the siren is sounding that means it can detect the sound from the siren and the installation of the AS 433 is now completed 6 If the red light indicator does not turn on which means the sensor cannot hear the siren So you need to increase the volume setting by slightly rotating the Volume switch 7 Activate the siren again and see if the audio sensor can hear the siren If the red light indicator does not turn on repeat step 6 until the red light indicator turns on Panel SC 001 Set the ON OFF TEST switch on the side of the Audio Sensor to ON and allow 15 seconds for the unit to warm up Enter the current MPIN Master Personal Identification Number on the SCo01 Press B Press the number key to identify which zone to add the Alarm Sensor to zone 1 2 3 4 It is not recommended to program this sensor to zone 1 or 2 because these zones are intended for Delay Mode The zone light s will flash for eight seconds While the zone light s are flashing press Now both the green and red lights flash for 30 seconds While the zone lights2. ensure it can hear the siren Caution You should keep the Volume setting as low as possible in order to eliminate false trigger by any background noise Installing the Audio Sensor 1 Place the Audio Sensor as close as possible to the siren or alarm unit of your existing security system This distance between the sensor and the siren should be less than 6 inches Note Selecting the place to locate the AS 433 is very critical since this will affect the operation and performance of the sensor You should avoid placing the Audio Sensor near any unwanted sound sources such as TV stereo to eliminate false trigger by back ground noise 2 Plug in the DC adapter cord to the DC jack on the Audio Sensor and plug in the other end to an electrical outlet If there is no elec trical outlet nearby the Audio Sensor can be operated by 9V battery the Skylink receivers that incorporate the Rolling as well Please refer to External Jack External power supply for more detail information 3 Apply the Velcro to the back of the sensor as well as the wall VOLUME __ LO HI DELAY LO HI MIC DC 9V PANIC BUTTON TEST ON EXT JACK Rw a Set up the Audio Sensor 1 Plug in the AC adapter and insert the wire to the DC 9V jack If there is no electrical outlet nearby the audio sensor you may use the 9V alkaline battery as the main power source If both power suppliers are connected the 9V adapter will
3. Introduction The Audio Sensor AS 433 is designed to detect sound frequency from the siren of your existing security system Once the siren goes off the Audio Sensor will be activated and therefore triggers the emergency dialer AD 433S by sending radio fre quency RF signal or through hardwire connec tion The Audio Sensor is designed to recognize only the siren from your existing security system therefore it will not pick up any background noise if the sensor is installed properly The sensor can also work in conjunction with all of Code Technology Security Control Panel SC 001 Emergency Dialer AD 1010 Audio Alarm AA 433 and Silent Alarm SW 433 4 Locate the Audio Sensor AS 433 and make sure it is secure Set up the Audio Sensor Caution Please make sure the Audio Sensor can only be triggered by the real alarm siren Some of the alarm systems will emit other sounds under different situations such as entry delay deeps this is to warn the user the alarm has been triggered user has to enter the password within a short period of time otherwise the alarm will go off Please make sure the Audio Sensor can only detect the intented alarm sound pattern Since the intented alarm is usually a lot louder than other sound patterns If the AS 433 can detect other sound pat terns from the alarm systems please adjust the Volume so that it can only detect the intented alarm 8 You should test the sensor several times in order to
4. are flashing activate the Audio Sensor by pressing the Panic button on the AS 433 You will hear a long beep from the SC 001 the zone light will stop flashing and the Audio Sensor will now com municate to that zone Program the Audio Sensor to Program the Audio Sensor Normal Operation External Jack the Emergency Dialer AD 433S to the Audio Alarm AA 433 Once you have installed your audio sensor properly Normally Closed N C Relay Dry Contact 1 Set the ON OFF TEST switch on the side 1 Set the switch on the side of the you should not change the setting since it will affect The audio sensor can work with the dialer through radio frequency wire of the Audio Sensor to ON and allow 15 Audio Sensor to ON Wait 15 the operation of the sensor and therefore may cause less or Normally Closed Contact wire connection You may insert one seconds for the unit to warm up seconds to warm up false alarm or malfunction In order to activate the end of the wire included to the audio sensor and connect the other end 2 Press L 5 on the keypad of the dialer 2 With only the ON light lit on audio sensor it has to detect the siren or similar of the wire to the N C contact of the emergency dialer please refer to the when in clock mode the display will show the Audio Alarm press and hold sound source for a fixed amount of time either 4 user manual of the dialer for more detail information If the sensor is L5 IdcodE the learn
5. button located on the seconds or 8 seconds This timing can be set by activated it will trigger the dialer through the wire connection 3 Activate the Audio Sensor by pressing bottom of the Audio Alarm adjusting the Delay Time setting When the Delay VEE P the Panic button on the AS 433 3 While pressing down on the time is set to LO the AS 433 has to detect the siren Caution Once the hardwire connection is established between the dialer learn button activatethe Audio for approx 4 seconds in order for it to be triggered and the Audio Sensor the Audio Sensor will be activated if the connection Sensor by pressing the Panic When the Delay time is set to HI this timing will be is broken or if the Audio Sensor is turned off When the red light indicator turns on that button on the AS 433 changed to 8 seconds This will eliminate the chance External power supply DC 9V means it is transmitting the signal to the 4 If a connection has been made of false alarm Once the audio sensor is activated The Audio Sensor can be powered by either 9V alkaline battery or external dialer Once the dialer has learned the sig the Audio Alarm will stop beeping it will send a signal to trigger the emergency dialer AC power adapter When the AC adapter is plugged in the 9V alkaline nal the display will return to clock mode and make a continuous tone AD 433S The dialer will then start dialing out all the battery works as a back up battery In cas
6. e of a power failure the audio until the black learn button preset phone numbers and ask for help sensor can still operate normally On the other hand you can use the 9V on the Audio Alarm is released alkaline battery as the primary power source as well if 9V DC is not con nected Battery Maintenance FCC NOTE When the voltage of the 9V battery drops to a certain level the audio If within one year from The Remote Control is approved If you would like to order Skylink s Skylink will not be held sen sor will notify you by flashing the red light indicator every 8 date by the FCC and it complies with product or have difficulty getting liable or responsible for SKY WK seconds This indicates the 9V battery needs to be replaced Note of purchase this product Part 15 of the FCC Rules Its your Skylink s product to work any misuse or application LM When the 9V adapter should become defective operation is subject to the please of this product other than a is connected to the AS 433 the low battery indication will be disabled except battery due to following two conditions 1 visit our website FAQ at for its intended use AUDIO SENSOR To replace the battery faulty workmanship or 1 This device may not cause www skylinkhome com or _ USER S INSTRUCTIONS 1 Turn off the audio sensor and disconnect the AC adapter from the sen Materials it will be repaired harmf l interference 2 email us at 2 Model AS 433 sor if the adapter is connec
7. ted or replaced without charge 2 This device must accept support skylinkhome com Caution If the N C hardwire connection is made disconnecting the Proof of purchase is any interference that may 3 call our toll free at g power or turning off the Audio Sensor will trigger the dialer Therefore required cause undesired operation 1 800 304 1187 from Monday E before replacing the battery or turning off the power please disable to Friday 9 am to 5 pm EST CUSTOMER SERVICE 35 the dialer WARNING Fax 800 286 1320 17 Sheard Avenue Brampton amp amp 2 Pry off the battery cover and remove the old Changes or modifications to Ontario Canada L6Y 143 Ba battery from the battery compartment ay this unit not expressly approved Fna uppaa girnome com 8 3 Connect the new 9V alkaline battery to the con j by the party responsible of PN Were Pe nector wire and place the battery inside the compliancecould void the user s US Patent 6243000B1 eg battery compartment authority to operate the 2004 SKYLINK GROUP es 4 Slide the battery cover back on equipment 5 Turn the Audio Sensor to ON mode
Download Pdf Manuals
Related Search