Scala Rider TeamSet Manual
Contents
1. E Az i O Gebrauchsanleitung Guide d Utilisation CARDO SYSTEMS INC Guida di Avvio Guia de Usario an 3 Bluetooth C AR DO SCALA RIDER TeamSet Congratulations and thank you for choosing the SCALA RIDER TeamSet Bluetooth Headset package for Motorcycle helmets The retail box of the SCALA RIDER TeamSet contains two headset units one headset for the driver and a second headset for the passenger The Driver s unit includes a Bluetooth module that allows the following uses Bluetooth headset for mobile phone communication supporting Headset and Handsfree profiles 10m 33 ft range 2 Transmitting GPS navigation instructions from a Bluetooth enabled GPS device 3 Intercom communications Driver Passenger Full Duplex 10m 33 ft range 4 MP3 Connectivity to an MP3 player The Passenger unit contains an intercom module and performs the following uses only range 2 MP3 connectivity to an MP3 player This manual will help you operate the headset but you should first familiarize yourself with the Bluetooth functionality of your mobile phone and or GPS device before using the Product Cardo wishes you an enjoyable and safe SCALA RIDER TeamSet experience Mobile phones that do not support the Bluetooth Handsfree profile may prevent you from using the Redial and Call Reject features Intercom communications Passenger Driver Full Duplex 10m 30 ft2. SCALA RIDER TeamSet Q JCARDO Two Headsets ee Volume Up Charging Jack Volume Down CTRL Control Button Intercom button Two Helmet Clamps Left Speaker short cord Right Speaker long cord Microphone m Back Tab Sliding Plate NOTE The use of two speakers may be illegal in certain jurisdictions Please check the local regulations and act accordingly U C AR DO SCALA RIDER TeamSet Wall Charger 2 Allen Wrenches 2 Sets of Velcro Pads 2 MP3 Cables 2 Glue Plates ee 2 Pre moistened Towelettes F 2 Carry Pouches E 4 Microphone Sponges Flat sponges for full face helmets and round sponges for other helmet types User Guide including Warranty and Registration form IMPORTANT Your headsets are water resistant devices designed for use under moderate rain or snow conditions However the headsets are not waterproof and should not be used under severe weather conditions The cover tongue protecting the Charging Jack should be kept tightly closed at all times to prevent moisture from entering the device Make sure that the headset is fully charged for at least four hours before initial use 1 Connect the wall charger to the headset s Charging Jack located between the two Volume Buttons 2 While charging the Red Light turns on it may take up to 15 seconds until the Red Light turns on When charging is co
3. Conference Call add passenger to an active call End Conference Call release passenger from a conference call FUNCTIONS REQUIRED ACTION During standby start talking loudly to activate the feature Stop talking The audio connection will be terminated within 25 seconds During an active phone call tap the intercom button During a conference call tap the intercom button Note In case the person on the other side of the intercom is not responding and you start talking 2 beeps will alert you that the other side is not available STATUS LIGHT None Alternating Red blue flashes 1 blue flash every 3 seconds 2 blue flashes every 3 seconds 1 red flash every 3 seconds 2 red flashes every 3 seconds Solid red Headset is off Mobile phone GPS Pairing mode Standby No call is in progress Call is in progress Battery is low Low battery while a call is in progress Charging SCALA RIDER TeamSet HOY IDO DESIRED RESULT Turn on the headset Turn off the headset Start using the Intercom Terminate operation of Intercom Enable disable Always on Intercom Increase Intercom volume Decrease Intercom volume PASSENGER S UNIT FUNCTIONS REQUIRED ACTION Press the CTRL Button steadily for at least 3 seconds Led indication three blue flashes Audio feedback Ascending tone low high Press the CTRL Button steadily for at least 3 seconds Led indication three red flashes Audio fee
4. Control without having to remove your hands from the handlebars The default mode of this feature is ON enabled Each time you switch off and turn on the headset the VR feature will be automatically enabled To disable enable the VR feature see phone functions below Note The VR feature works well while driving up to 70km h or 44m h with 3 4 helmet and up to 120km h or 75m h with a closed full faced helmet PHONE FUNCTIONS Answer a call Tap the CTRL Button or speak loudly any word of your choice Reject a call Tap the Intercom Button or remain silent for 15 seconds during an incoming call Terminate a call Press and hold the Intercom Button for 3 seconds when a call is in progress For some mobile phones you may need to press the Control button to end the call Voice Dial During Standby tap the CTRL Button and state the name of the person you wish to call This feature is supported only by mobile phones that support the Voice Dial feature Redial During Standby tap the Intercom Button Enable Disable Long press the volume up and down buttons simul voice command taneously until you hear a beep The default status is feature voice command enabled o ee NOTE If your Bluetooth mobile phone is paired to a Bluetooth GPS device not directly to the SCALA RIDER TeamSet some of the above Phone functions may not be compatible GENERAL DESIRED RESULT Start using the intercom Terminate operation of Intercom
5. If this is the case you should tuck away the long corded speaker underneath the helmet padding as follows Lead the speaker cord B alongside the rim of the padding to the right side and then back to the left side near speaker A Then place the speaker B underneath the padding ATTACHING Slide the headset downwards along the sliding panel until a clicking sound indicates that the headset is locked in place SCALA RIDER TeamSet HOY IDO Press here to remove REMOVING Your headset can be removed for charging and storage by pressing your finger gently against the tab and sliding the headset up with the other hand We recommend that you remove the headset from the helmet when not in USE The different Audio Sources that are connected to the SCALA RIDER TeamSet are prioritized as follows Highest 1 Mobile phone audio Incoming outgoing calls GPS device GPS audio and navigation instructions 2 Driver to Passenger Full Duplex Intercom Connection Lowest 3 MP3 Connectivity A high priority Audio Source will always interrupt any lower priority Audio Source i e Mobile phone call overrides Intercom calls AUDIO SOURCES AND PRIORITIES Passenger Unit Passenger can also initiate intercom calls with drivers unit as well as listen to music from his MP3 Player Intercom call overrides the audio from the MP3 player Your SCALA RIDER headset can be connected to an MP3 player audio device by si
6. headset unit can be mounted or released from the Helmet Clamp at any time There are two methods that can be used in order to attach the Clamp onto the helmet Standard Method Recommended for most helmet types Glue Plate Method Recommended for helmets to which the standard method cannot be applied using the Glue Plate included in the box Standard Method ee 1 Use the enclosed Allen Wrench to loosen the two screws on the Back Plate ae 2 Slide the Back Plate between the internal padding A and the external shell ofthe helmet 3 Adjust the clamp s location so that the microphone is located opposite center of your mouth and then tighten the screws You may need to reposition the Clamp repeatedly until you identify the best spot The microphone must be positioned vertically and not horizontally Glue Plate Method You have the option to glue the Helmet Clamp onto your helmet when the above standard method cannot be used or in case you prefer to secure the Helmet Clamp with adhesive glue This option has been successfully used for a range of high end helmets NOTE While we have no reason to believe that the gluing option might negatively affect any helmet Cardo does not assume any responsibility to that affect ir respective of its nature and circumstances The Glue Plate is offered as a free option that you may choose to use at your own risk and subject to renouncement of any future claims Caution This proc
7. EFUND WITHIN THE PERIOD PROVIDED YOU ARE EXPLICITLY IN AGREEMENT WITH THE ABOVE AND RENOUNCE ALL RIGHTS TO FU TURE CLAIMS AND DEMANDS AGAINST CARDO AS DEFINED ABOVE www cardosystems com
8. SCALA RIDER TeamSet HOP IDO IC RF Radiation Exposure Statement This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter European CE Notice The SCALA RIDER TeamSet headset the Product is in conformity with the following essential requirements of Council Directive 1999 5 EC referred to as R amp TTE Directive Articles 3 1a 3 1 b and 3 2 The Product is manufactured in accordance with Annex II of the above directive Declaration of Conformity DOC The SCALA RIDER TeamSet headset is compliant with and adopts the Bluetooth Specification 2 0 and has successfully passed all interoperability tests that are specified in the B uetooth specification However interoperability between the device and other Bluetooth enabled products is not guaranteed WAIVER AND GENERAL RELEASE By using the SCALA RIDER TeamSet headset s hereafter referred to in the singular you will waive substantial legal rights including the right to sue Please read the following carefully before using the device If you do not accept all terms of this agreement you should immediately return the product for a full refund By using the headset you agree to be bound to this agreement and forfeit the right to su
9. ally capable to use the Device and that you have no medical conditions or needs that may infringe upon your abilities to do so in a safe manner You confirm that you are at least eighteen 18 years of age and that you have been advised of the risks associated with the use of the Device You further confirm that you will not consume any alcohol that may affect your alertness or any mind altering substance and will not carry use or consume these substances before or during the use of the Device 4 You fully acknowledge our warnings and understand that a risks and dan gers exist in using the Device while in traffic including but not limited to in jury or illness strains fractures partial and or total paralysis death or other ailments that could cause serious disability b these risks and dangers may be caused by the negligence of the manufacturers or its agents or any third party involved in designing or manufacturing the Device c these risks and dangers may arise from foreseeable or unforeseeable causes You hereby K q lt _ __ _ lt _ E _ I SSE NR DO SCALA RIDER TeamSet c assume all risks and dangers and all responsibility for any losses and or damages whether caused in whole or in part by the negligence or other conduct of others including the Company 5 You confirm that you have read this release of liability and fully understand its terms and that you have given up subst
10. antial rights by not returning the Device for a full refund see refund option below Disclaimer of Warranty CARDO DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES WITH REGARD TO THE ENCLOSED DEVICE INCLUDING WITHOUT LIMITATION ANY IMPLIED WARRANTIES OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NON INFRINGEMENT THE DEVICE AND ITS ACCESSORIES ARE PROVIDED AS IS AND AS AVAILABLE WITHOUT WARRANTY OF ANY KIND BEYOND THOSE ASSUMED IN THE ENCLOSED MANUAL Limitation of Liability IN NO EVENT SHALL CARDO BE LIABLE FOR ANY SPECIAL INDIRECT PUNITIVE INCIDENTAL EXEMPLARY OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THE DEVICE WHETHERBASEDONBREACHOF CONTRACT TORT INCLUDING NEGLIGENCE PRODUCT LIABILITY OR OTHERWISE EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES YOU ACKNOWLEDGE AND AGREE THAT THE LIMITATIONS SET FORTH ABOVE ARE FUNDAMENTAL ELEMENTS OF THIS AGREEMENT AND THE DEVICE WOULD NOT BE PROVIDED TO YOU ABSENT SUCH LIMITATIONS SOME STATE STATUTES MIGHT APPLY REGARDING LIMITATION OF LIABILITY RETURN FOR FULL REFUND IF YOU ARE UNWILLING TO ACCEPT AND AGREE TO THE ABOVE CONDI TIONS YOU MAY RETURN THIS DEVICE TO CARDO FOR A FULL REFUND PROVIDED THAT YOU DO SO NO LATER THAN 7 BUSINESS DAYS FOL LOWING THE PURCHASE OF THE DEVICE proof of purchase required AND SUBJECT TO THE WRAPPING BEING INTACT WHEN DOING SO PLEASE REFER TO THIS SECTION BY NOT RETURNING THE DEVICE FOR R
11. at belong to you or to third parties any of which may result from using the Device under any circumstances or conditions and irrespective of jurisdiction Cardo will not be responsible for any physical damages irrespective of reasons conditions or circumstances including malfunctioning of the Device and all risks associated with operating it rest solely and entirely with the user of this Device irrespec tive of whether the Device is used by the original purchaser or any third party Cardo hereby notifies you that using this Device may also be in contravention to local federal state or national laws or regulations and that any use of the Device is entirely at your sole risk and responsibility 1 You your heirs legal representatives successors or assigns hereby vol untarily and forever release discharge indemnify and hold harmless Cardo from any and all litigation claims debts demands actions and liability which may arise directly or indirectly from using the Device for any distress pain suffering discomfort loss injury death damages to or in respect to any per son or property however caused WHETHER ARISING FROM THE NEGLI GENCE OR OTHERWISE and which may hereafter accrue to you on some future date as a result of said use to the fullest extent permitted by law 2 You fully understand and assume the risks in using the Device including risk of negligent acts or omissions by others 3 You confirm that you are physic
12. dback Descending tone high low During standby start talking loudly to activate the Intercom Stop talking The audio connection will be terminated within 25 seconas During standby tap the Control Button One tone intercom enabled Two tones intercom disabled Tap the Volume Up Button Tap the Volume Down Button Note In case the person on the other side of the intercom is not responding and you start talking 2 beeps will alert you that the other side is not available STATUS LIGHT None One blue flash every 3 seconds Steady red Charger is connected Steady red Charger is not connected Headset is off Headset is on Headset is being charged Headset in Intercom pairing mode C AR DO SCALA RIDER TeamSet For additional information please visit our website at www cardosystems com FAQ www cardosystems com faq or contact us at support cardosystems com Phone USA and Canada 1 800 488 0363 International 4989 450 36819 Federal Communications Commission FCC Statement 15 21 You are cautioned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC rules These limits are designed to provide reasonable protection against harmful interference in a
13. e Using a communication device while riding a motorcycle scooter moped ATV quad bike or any other vehicle or equipment whether on land water or air jointly referred to as Vehicle requires your complete and undivided attention Cardo Systems Inc including its Officers Directors Affiliates Parent Company Representatives Agents Contractors Sponsors Employees Suppliers and Resellers jointly referred to as the Company or Cardo strongly advises you to take all necessary precautions and remain alert to the traffic weather and road conditions if you choose to use the SCALA RIDER TeamSet headset including all derivative models irrespective of its commercial name or branding the Device and stop your Vehicle on the roadside prior to initiating or receiving calls Any publications advertisements announcements or similar notes that refer to using the Device while riding a Vehicle are solely intended to address its technical capabilities and should not be misconstrued as if encouraging users to operate the Device while actively involved in traffic By way of purchasing this Device and not returning it for a full refund see below you are irrevocably releasing indemnifying from any liability loss claim and expense including attorneys fees and holding Cardo harmless for any bodily injuries harm or death as well as losses or damages in goods to any Vehicles including your own or to any property or asset th
14. ess can be done only once 1 Use the enclosed Allen Wrench to remove both Allen screws and release the Helmet Clamp s back plate 3 Adjust the Helmet Clamp s location on the Helmet so that the microphone is located opposite the center of your mouth You may need to reposition the Clamp repeatedly until you identify the best spot The microphone must be positioned vertically and not horizontally Be sure to clean the selected area prior to the gluing process as described in 4 below 2 Determine the location on the helmet where the Helmet Clamp must be attached 4 Use the pre moistened Towelette to clean the helmet area where you want to install the Glue Plate Allow to dry thoroughly 5 Peel the foil cover from the Glue Plates adhesive pad 6 Place the Glue Plate into position according to 3 Press firmly 15 seconds on all 3 parts of the Glue Plate 7 The adhesive pad bonds to full strength over the next 24 hours Therefore it is recommended to not use the headset during this 24 hour period 8 Fasten the Clamp to the Glue Plate using the Allen screws that were previously removed Attach the speakers to the Velcro inside your helmet opposite your ears short speaker cord for the left Speaker A ear A and the long speaker cord B Y for the right ear You may want to a Speaker B A use the supplied Velcro pad Using two speakers inside the Cable helmet may be prohibited in certain jurisdictions
15. irm that pairing has succeeded and the headset will begin flashing slowly in Blue NOTE If the Pairing process is not completed within two minutes the headset will return to Standby mode With some mobile phones you may need to tap the CTRL button to connect the headset to the phone after pairing is complete The SCALA RIDER TeamSet headset will automatically connect to the last phone connected to the headset SET UP FOR BLUETOOTH GPS DEVICE If you have a Bluetooth enabled GPS device and would like to transmit navigation instructions and sounds N from the GPS device through the headset s speakers please follow instructions described in section below TO PAIR THE SCALA RIDER TeamSet TO A Bluetooth GPS DEVICE If you want to use your mobile phone and your GPS device with the SCALA RIDER TeamSet Driver s unit headset you should proceed as follows 1 Pair your GPS device to your mobile phone Please consult your GPS device s User Manual for more information 2 Pair your headset to the GPS device as described below SA NOTE Not all Bluetooth enabled GPS devices allow connections to Bluetooth headsets like the SCALA RIDER TeamSet Please consult your GPS device s User Manual for more information ace THE SCALA RIDER TEAMSET TO A BLUETOOTH GPS 1 Turn on your GPS device 2 With the Driver s unit headset turned OFF press and hold the CTRL Button until the Red and Blue Lights begin rapidly alternating 3 Search f
16. mplete the Red Light will turn off Driver to Passenger NON yw lt Full Duplex Intercom xX Connection PUN 10m 30ft Y N E Mobile Phone ae MP3 Player Driver and Passenger SET UP FOR MOBILE PHONE CALLS fyou have a Bluetooth enabled mobile phone and would like to make and receive phone calls using the SCALA RIDER TeamSet Driver s unit you must first pair your headset to the mobile phone Pairing is a one time process Once the headset is paired to a specific mobile phone during this Setup Procedure they will remain paired and automatically recognize each other whenever they are within range If the connection between the phone and headset is lost tap the CTRL button to reconnect the devices TO PAIR THE SCALA RIDER TEAMSET TO A BLUETOOTH MOBILE PHONE 1 Turn on your phone and make sure its Bluetooth function is activated 2 With the Driver s unit headset turned OFF press and hold the CTRL Button until the Red and Blue Lights begin rapidly alternating SCALA RIDER TeamSet HOY IDO 3 Search for Bluetooth devices on your phone by following the phone s instructions Please consult your phone s User Manual for more information 4 After a few seconds the phone will list the SCALA RIDER TeamSet as a discovered device Select it and follow your phone s instructions to accept the pairing 5 When prompted enter 0000 four zeros as your PIN or passkey 6 Your phone will conf
17. mply plugging it to the Helmet Clamp s jack with the audio cable as follows C AR DO SCALA RIDER TeamSet 1 Power on the headset to have it on Standby mode flashing slowly in Blue 2 Connect one side of the audio cable to your MP3 player audio device s jack and the other side to the helmet Clamp s jack as shown in the photo 3 Operate the MP3 Player audio device by using its buttons FF REW PLAY PAUSE NOTE Volume can only be adjusted through the MP3 Player Any other audio connection will automatically mute the MP3 Player The audio signal will return only when headset is once again in Standby mode DRIVER S UNIT FUNCTIONS GENERAL FUNCTIONS DESIRED RESULT REQUIRED ACTION Turn on the Press the CTRL Button steadily for at least 6 seconds headset Led indication three blue flashes Audio feedback Ascending tone low high Turn off the Press the CTRL Button steadily for at least 3 seconds headset Led indication three red flashes Audio feedback Descending tone high low Increase volume Tap the Volume Up Button Decrease volume Tap the Volume Down Button AGC Automatic Gain Control In addition to manual Volume Control the SCALA RIDER TeamSet will automatically increase and reduce its volume according to ambient noise and driving speed Connect the audio cable to the helmet Clamp s jack Voice Recognition VR The VR feature allows you to answer or reject incoming calls by voice
18. ned that changes or modifications not expressly approved by the part responsible for compliance could void the user s authority to operate the equipment 15 105 b This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the IC rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device e
19. or Bluetooth headsets on your GPS device by following the device s instructions Please consult your GPS device s User Manual for more information 4 If your GPS device prompts for a PIN or Passkey enter 0000 four zeros 5 Your GPS device will confirm that pairing has succeeded The headset will begin flashing slowly in Blue 6 If you wish to use a Bluetooth mobile phone to make and receive calls through the headset you must now pair your mobile phone to your GPS device by following your GPS and or mobile phone s instructions NOTE If the Pairing process is not completed within two minutes the headset will return to Standby mode The two headset units Driver and Passenger units are supplied facto ry paired Therefore you do not need to pair these devices However if re pairing is needed you may proceed as follows 1 Make sure that both units are turned ON and close to each other 2 Press the Intercom Buttons of both devices simultaneously for at least 10 seconds the red Status Light of the passenger unit will light steadily 3 If successful the blue Status Light of the passenger unit will flash 4 If pairing has failed the red Status Light of the passenger unit will turn off and you must repeat the procedure eamSet C AR DO SCALA RIDER TeamS Perform this procedure for both the driver and the passenger helmets The Helmet Clamp must be attached to the left side of the helmet Once attached the
20. residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Operation is subject to the following two conditions 1 this device may not cause interference and 2 this device must accept any interference including interference that may cause undesired operation of the device FCC RF Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment End users must follow the specific operating instructions for satisfying RF exposure compliance This transmitter must not be co located or operating in conjunction with any other antenna or transmitter Industry Canada IC Statement 15 21 You are cautio
Download Pdf Manuals
Related Search