Home

User Manual - D-Link

1. You have completed your IP camera setup Please click the Back button if you want to review or modify your settings or click on the Apply button to save and apply your settings Motion Detection Disable EVENT Video Clip Schedule Day Sun Mon Tue Wed Thu Fri Sat Schedule Time Always Alerts and Notification Do not notify me 24 Configuration Network Setup Use this section to configure the network connections for your camera All relevant information must be entered accurately LAN Settings DHCP Static IP Address IP Address Subnet Mask Default Gateway Primary DNS Secondary DNS Enable UPnP Enable UPnP Port Forwarding Settings for your local area network Select this connection if you have a DHCP server running on your network and would like your camera to obtain an IP address automatically You may obtain a static or fixed IP address and other network information from your network administrator for your camera static IP address may simplify access to your camera in the future Enter the fixed IP address in this field This number is used to determine if the destination is in the same subnet The default value is 255 255 255 0 The gateway used to forward frames to destinations in a different subnet Invalid gateway settings may cause the failure of transmissions to a different subnet The primary domain name server translates names to IP addresses Th
2. Format SD Card Total 3865192KB Used 20KB Free 3865172KB o Here you could browse and manage the record files which stored in SD card SD CARD 46 Configuration Advanced Digital Input Output This screen allows you to control the behavior of digital input and digital output devices The I O connector provides the physical interface for digital output DO and digital input DI that is used for connecting a diversity of external alarm devices such as IR Sensors and alarm relays The digital input is used for connecting external alarm devices and once triggered images will be taken and e mailed Select D I or D O The camera will send a signal when an event is triggered depending Mode upon the type of device connected to the DI circuit N C stands for Normally Closed This means that the normal state of the circuit is closed Therefore events are triggered when the device status changes to Open N O stands for Normally Open This means that the normal state of the circuit is open Therefore events are triggered when the device status changes to Closed Video Output Enable disable the BNC terminal TV output signal D I and D O kis Pin Block L T LOLA D Link DCS 3714 User Manual The I O connector provides the physical interface for digital output DO and rear input DI that is used for connecting a diversity of external alarm devices such as IR Sensors and alarm relays The digital in
3. This section explains how to configure your new D Link Network Camera using the Web based Configuration Utility Click on the D Link Setup Wizard SE icon that was created in your Windows Start menu Start gt D Link gt Setup Wizard SE Select the camera and click the button labeled Link to access the web configuration SECURICAM Network The Setup Wizard will automatically open your web browser to the IP address of the camera MAC Address Current IP Address Device Name DCS 3714 Alternatively you may manually open a browser and enter the IP address of the 3714 Microsoft Internet Expl camera 192 168 0 20 DC5 3714 Microsoft Internet Expla ie gt http 192 168 0 20 E x vr ode bocs s714 D Link DCS 3714 User Manual 16 Configuration Enter admin as the default username and leave the password blank Click OK to continue Windows Security The server 192 168 0 102 at DCS 3714 requires a username and password Warning This server is requesting that your username and password be sent In an insecure manner basic authentication without a secure connection f rr Password E Remember my credentials _ ox Cancel This section shows your camera s live video You can select your video profile and view or operate the camera For additional information about web configuration please refer to the user manual included on the CD ROM or the
4. 1 post event image s 0 7 File Name Prefix C Add date and time suffix to file name O Video Clip Source Profile1 V v Pre event recording Second s 0 4 Maximum duration Second s 1 100 Maximum file size Kbytes 100 5000 File Name Prefix name System log Video clip Select this option to enable video clips Source The source of the profile profile1 profile2 or profile3 Pre event The interval of pre event recording in seconds recording Maximum The maximal recording file duration in seconds duration Maximum file The maximal file size would be generated size File name prefix The prefix name will be added on the file name of the video clip System log Select this option to save events to the camera system log D Link DCS 3714 User Manual 40 Configuration Send post event image s 0 7 Specify to capture the number of images after a trigger is activated A maximum of seven images can be generated For example If both the Send pre event images and Send post event images are set to four a total of 9 images are generated after a trigger is activated The moment the trigger is activated Add a date and time suffix to the file name Select this option to add a date and time to the file name suffix SNAPSHOTS20080104_ 100341 tf 4 File name prefix Date and time suffix The format is YYYYMMDD_HHMMSS Maximum duration Specify the maximal recording d
5. 1 D Link Version 1 00 09 01 2014 User Manual HD Day and Night WDR Camera with Lowlight DCS 3714 nm Preface D Link reserves the right to revise this publication and to make changes in the content hereof without obligation to notify any person or organization of such revisions or changes Information in this document may become obsolete as our services and websites develop and change Manual Revisions Revision Date Description gt April 11 2014 DCS 3714 Revision A1 with firmware version V1 00 Trademarks D Link and the D Link logo are trademarks or registered trademarks of D Link Corporation or its subsidiaries in the United States or other countries All other company or product names mentioned herein are trademarks or registered trademarks of their respective companies Copyright O 2014 D Link Corporation All rights reserved This publication may not be reproduced in whole or in part without prior expressed written permission from D Link Systems Inc D Link DCS 3714 User Manual Table of Contents Product Overvien Lususnnsmnsnnuevivdminknsskkanen 4 Package Contents ccccccceseeeeceeeeseeeeeeeeeeseeeeeas 4 MON 5 System ROQUINGINGING en 5 CU CS ren 6 Hardware Overview cccsccsseccseecnsecnsecnsecnsecnnenenenens 7 Hardware Overview rrararennrnnnenaverarennenunennrnneennnenene 7 EEE EE 7 Fl 2 8 Configuration with Wizard rrnnennnnnnnnnnennnnrnnnnnnn 11 Seg ike U
6. Motion Motion is detected during live video monitoring Select the windows Network lost Detection that need to be monitored EVENT SCHEDULE W Sun M Mon W Tue M Wed vw Thu W Fri M Sat Periodic The event is triggered in specified intervals The trigger interval unit PEN IS in minutes O From 00 00 To 23 59 V ACTION C Trigger D O for seconds Digital input The external trigger input to the camera System Boot Triggers an event when the system boots up a a Network Lost Triggers an event when if the network connection is lost Event Schedule Select Always or enter the time interval Trigger D O Select to trigger the digital output for a specific number of seconds when an event occurs D Link DCS 3714 User Manual 43 Configuration Add Recording Here you can configure and schedule the recording settings Recording entry The unique name of the entry name Enable this Select this to enable the recording function recording Priority Set the priority for this entry The entry with a higher priority value will be executed first Source The image profile used for the source of the stream Recording schedule Scheduling the recording entry Recording settings Configuring the setting for the recording Destination Select the folder where the recording file will be stored Total cycling recording size Please input a HDD volume between 1MB and 2TB for recording space The rec
7. Read only community public Enable SNMPv3 Read Write Security name private Authentication type Authentication password Encryption password Read only security name Authentication type Authentication password Encryption password Dont Save Samas 53 Configuration Maintenance Device Management You may modify the name and administrator s password of your camera as well as add and manage the user accounts for accessing the camera You may also use this section to create the unique name and configure the OSD setting for your camera Admin Password Set a new password for the administrator s account Setting Add User Add new user account Account User Name Password User List Camera Name Enable OSD Label Show Time The user name for the new account The password for the new account All the existing user accounts will be displayed here You may delete accounts includes in the list but please reserve at least one as guest Create a unique name for your camera that will be added to the file name prefix when creating a snapshot or a video clip Select this option to enable the On Screen Display feature for your camera Enter a label for the camera Select this option to enable the time stamp display on the video screen D Link DCS 3714 User Manual Here you can change the administrators password for your IP camera as well as add and or delete user account s You can configur
8. as white on the screen Changes the exposure mode Use the dropdown box to set the camera for Indoor Outdoor or Night environments or to capture Moving objects The Low_Noise option will focus on creating a high quality picture without noise You can also create 3 different custom exposure modes The Max Gain setting will allow you to control the maximum amount of gain to apply to brighten the picture This setting controls the amount of noise reduction that will be applied to the picture Adjust this setting to compensate for backlit subjects D Link DCS 3714 User Manual Changes to your IP camera settings are made immediately LIVE VIDEO C Enable Privacy Mask Setting IMAGE SETTINGS White Balance Exposure Mode Denoise Brightness Contrast Saturation Sharpness WDR Level 3D filter Reset Default 29 Configuration Contrast Saturation Sharpness WDR Level 3D Filter Reset Default Adjust this setting to alter the color intensity strength This setting controls the amount of coloration from grayscale to fully saturated Specify a value from 0 to 8 for image edge enhancement The WDR function is especially effective in environment with extreme contrast such as lobby entrances parking lots ATMs and loading areas higher WDR setting will help in reducing areas with high contrast Setting this option to Low Medium or High will help to reduce image artifacts and res
9. for stream streams via group address and specify the TTL value for each stream Enter the port and TTL settings you wish to use if you do not want to use the defaults lt lt lt Optional primary DNS Enable multicast for stream 1 Multicast group address Multicast video port Multicast RTCP video port Multicast audio port Multicast RTCP audio port Multicast TTL 1 255 _ Enable multicast for stream 2 Multicast group address Multicast video port Multicast RTCP video port Multicast audio port Multicast RTCP audio port Multicast TTL 1 255 Save Settings Don t Save Settings D Link DCS 3714 User Manual 27 Configuration Dynamic DNS DDNS Dynamic Domain Name Server will hold a DNS host name and synchronize the public IP address of the modem when it has been modified A user name and password are required when using the DDNS service Enable DDNS Select this checkbox to enable the DDNS function Server Address Select your Dynamic DNS provider from the pull down menu or enter the server address manually Host Name Enter the host name of the DDNS server User Name Enter your user name or e mail used to connect to the DDNS Password Enter your password used to connect to the DDNS server Timeout Enter DNS Timeout values Status Indicates the connection status which is automatically determined by the system D Link DCS 3714 User Manual T
10. images to a hard drive viewing up to 32 cameras on one screen and taking snapshots PoE Power over Ethernet for Streamlined Installation The DCS 3714 can get all the power it needs from a PoE switch or PoE injector for a simple and clutter free installation All Day Surveillance with low light color image capability The built in Sony sensor allows you to monitor an area during the night with full color images The DCS 3714 provides clear detail and high quality video at any hour of the day by automatically adjusting its a built in removable IR cut filter Add External Controls or Devices An integrated RS 485 interface provides connectivity to an optional pan tilt enclosure which effectively adds pan tilt functionality to the DCS 3714 while input and output ports allow connectivity to external devices such as IR sensors switches and alarm relays D Link DCS 3714 User Manual 6 Hardware Overview Hardware Overview Rear VIDEO OUT r AUDIO I 5 I T F a i zl r _ 5 i I AUDIO OUT Ethernet PoE RJ 45 connector for Ethernet which can also be used to power the camera using PoE 12V DC 3 Audion Audio input connector for a microphone 4 Reset Press and hold this button for 5 seconds to reset the camera 6 Audio Out Audio output for external speakers 8 LED Powerandnetworkindicator S O D Link DCS 3714 User Manual Hardware Overview Front Connect to a CS mount ICR
11. me Method are aval ab amp Create self signed certificate automatically Create self signed certificate manually Create certificate request and install Create a self signed certificate automatically Create a self signed certificate manually EE Create a certificate request and install CERTIFICATE INFORMATION Status No installed Status Displays the status of the certificate CSR Property Certificate Property Remove Note The certificate cannot be removed while the HTTPS is still enabled Save Settings Don t Save Settings To remove the certificate you must first uncheck Enable HTTPS secure connection D Link DCS 3714 User Manual 50 Configuration Access List Here you can set access permissions for users to view your DCS 3714 Allow list Start IP address End IP address Delete allow list Deny list Delete deny list The list of IP addresses that have the access right to the camera ETT The starting IP Address of the devices Such as a computer that BES have permission to access the video of the camera Click Add to save the changes made Delete allow list Note A total of seven lists can be configured for both columns adle Start IP address End IP address The ending IP Address of the devices such as a computer that Dete deny ist have permission to access the video of the camera Remove the customized setting from the Allow List The lis
12. 014 01 01 00 00 10 IP CAMERA ACQUIRE DHCP IP 192 168 1 100 2014 01 01 00 00 01 SYSTEM SET DCPOWER ON 2014 01 01 00 00 01 SYSTEM SWITCH TO DC IRIS MODE 2014 01 01 00 00 00 SYSTEM BOOTING 2014 01 01 00 00 08 IP CAMERA ACQUIRE DHCP IP 192 168 1 100 2014 01 01 00 00 01 SYSTEM SET DCPOWER ON 2014 01 01 00 00 01 SYSTEM SWITCH TO DC IRIS MODE 2014 01 01 00 00 00 SYSTEM BOOTING 2014 01 05 01 48 33 admin FROM 192 168 1 2 LOGIN OK 2014 01 01 00 00 10 IP CAMERA ACQUIRE DHCP IP 192 168 1 100 2014 01 01 00 00 00 SYSTEM SET DCPOWER ON den 58 Configuration Help This page provides helpful information regarding camera operation LIVE VIDEO Camera Setup Wizard Network Setup Dynamic DNS Audio and Video Preset Time and Date Event Setup SD Card ADVANCED DI and DO R5 485 HTTPS Access List SNMP MAINTENANCE STATUS Device Info og D Link DCS 3714 User Manual 59 Appendix DI DO Schematics DI DO f DC 12V total output cument maximum to 100mA4 li so boner 12V 0 oe O gt 12V 10 IR luminator 7 DI1 O J Reed switch DIt CO Photo Relay i WW DIO Vibration DI2 O vo Photo Relay DO IC ALARM no O Photo Relay 485 JE gt 485 QO R5455 Device D Link DCS 3714 User Manual 60 Appendix Technical Specifications Camera Camera Hardware e 1 3 Megapixel progressive CMOS sensor e Angle of view Profile e Minimum illumin
13. D Link website a a oax Bae AMA mm SECURITY D Link DCS 3714 User Manual 17 Configuration Live Video This section shows your camera s live video You may select any of the available icons listed below to operate the camera You may also select your language using the drop down menu on the left side of the screen You can zoom in and out on the live video image using your mouse Right click to zoom out or left click to zoom in on the image Digital Input This indicator will change color when a digital Indicator input signal is detected Motion Trigger This indicator will change color when a trigger Indicator event occurs Note The video motion feature for your camera must be enabled Recording When a recording is in progress this indicator Indicator will change color Video Profile 1 Video Profile 2 Video Profile 3 Full screen mode o Taking a Snapshot Recording a Video Clip Set a Storage Folder Listen Stop Listening e7 This control pad can be used to pan tilt and zoom Control Pad within the camera s predefined view area if one Talk Stop Talking has been defined Start Stop Digital Output gt fe ee D Link DCS 3714 User Manual 18 Configuration Go To If any presets have been defined selecting a preset from this list Preset List will display it SD Status This option displays the status of the SD card If no SD card has been inserted this sc
14. Sensor The IR Cut Removable sensor judges lighting conditions and switches from color to infrared accordingly D Link DCS 3714 User Manual Hardware Overview 43 1 AES Auto Electric Shutter DC Iris Connector Connector for DC auto Iris lens Toggles between several 2 DC IRIS Use an auto iris DC drive Ede 3 NTSG TV output signal selector 2 4 4 PAL TV output signal selector D Link DCS 3714 User Manual Hardware Overview SD Card Slot Local SD Card for storing recorded images and video D Link DCS 3714 User Manual 10 Hardware Overview Configuration with Wizard Insert the DCS 3714 CD into your computer s CD ROM drive to begin the installation If the Autorun function on your computer is disabled or if the D Link Launcher fails to start automatically click Start gt Run Type D autorun exe where D represents the drive letter of your CD ROM drive Click Installation Wizard to begin the installation pe Setup Wizard pe i amp View Documentation Install D ViewCam Support DCS 3714 Business Class Networking After clicking Setup Wizard the window on the right will open Welcome to the InstallShield Wizard for Setup Click Next to continue Wizard SE The InstallShield Wizard will install Setup Wizard SE on pour computer To continue click Next Cancel D Link DCS 3714 User Manual 11 Hardware Overview Click Yes to accept the License Agreement In
15. T gg sopranen ai a AAT Eaa 16 Web based Configuration Utility ee 16 Live Video EE 18 Setup EEE 20 WY ZN 0 EE 20 Internet Connection Setup Wizard 20 Motion Detection Setup Wizard rrranrnannnrr 23 Network Setup cccecceeeseeeseeeeeeteeeeseeeeeeeeees 25 Dynamic DNS Gers 28 Image Setup nr 29 Audio and Video rarranrnnrnannnnrnarnannnnrnannnennennnre 31 PEN 33 Motion Detection arrnnrnnrnnrnnrnnrnnrnnnnnnnnnnnnr 35 Time and Date rrannnnnnnrnnrnnnnnrnnrnnrnannnnnnnnnnnnnn 36 Event SD 37 D Link DCS 3714 User Manual ae 8 0 1 0 g EE EN 38 Add Server rmrarerererrevarerarenvernvevrersennvennneneee 39 Add Media rrannnannnnrnnnenannnarnnnennnenannnnrnnnnnunenere 40 DET 46 PTE 47 Digital Input Output serorrrnnrernnronnnrrnnanennnner 47 HO edeense en 48 16 5 EE 49 PAI IPS Ler 50 RES IL 51 SNP 52 Maintenance arnernrrnnnnnnarnnrnernannnnannunnernernannennsnere 54 Device Management c ccssscsssceesseeeseeess 54 Backup and Restore ranrnnnnnrnnrnnrnnnnnrnnnnnnnnere 55 Firmware Upgrade EE 56 ST GE EE 57 Device NN br Kole gt EE ENES 58 PICO ENE 59 Fe 011 0 gt EE ES a 60 DI DO Schematics icccsacenscaccosenssenemereseasencicenon anne 60 DD E E EE E E 60 Technical Specifications rrrarerarerarerarernnrnnnennere 61 Product Overview Package Contents DCS 3714 Network Camera CAT5 Ethernet cable CD ROM wi
16. account Server Name amp Email Sender email address Network Storage Specify a network storage device Only one network storage device Recipient email address is supported Server address User name SD Card Use the camera s onboard SD card storage Password Port C This server requires a secure connection StartTLS Server address Port User name y Password Remote folder name C Passive mode O Network storage Network storage location for example my_nas disk folder Workgroup User name Password Primary WINS server SD Card Test Save Settings Don t Save Settings D Link DCS 3714 User Manual 39 Configuration Add Media There are three types of media Snapshot Video Clip and System Log Media Name Enter an unique name for media Snapshot Select this option to enable snapshots Source The stream source Profile 1 Profile 2 or Profile 3 Send pre event The number of pre event images image s 0 4 Send post event The number of post event images image s 0 7 File name prefix The prefix name will be added on the file name Add date and Check it to add timing information as file name suffix time suffix to file You can set at most 5 different media here for different event Dont Save Settings MEDIA TYPE Media name Snapshot Source Profiler V v Send i pre event image s 0 4 Send
17. ation 0 1 lux Color e H 35 6 to 95 e Built in Infrared Cut Removable ICR Filter module e V 20 to 50 9 e DC iris varifocal length 2 9 mm to 8 2 mm e D 41 to 112 3 e Aperture F1 0 e Minimum object distance 0 5m Image Features e Configurable image size quality frame rate and bit rate e Configurable privacy mask zones Time stamp and text overlays e Configurable WDR white balance shutter speed brightness saturation e Configurable motion detection windows contrast and sharpness Video Compression e Simultaneous H 264 MPEG 4 MJPEG format compression e H 264 MPEG 4 multicast streaming e JPEG for still images Video Resolution e 16 9 1280 x 720 800 x 450 640 x 360 480 x 270 320 x 176 up to 30 fps 4 3 1024 x 768 800 x 600 640 x 480 480 x 360 320 x 240 up to 30 fps Audio Support External Device e 2DI 1 DO interface e Audio input output Interface e 12 V DC 100 mA Output Video output e RS 485 e SD SDHC SDXC card Slot accepts cards up to 64 GB Network Network Protocols PV6 HTTP HTTPS e IPv4 e Samba client e TCP IP e PPPoE e UDP UPnP port forwarding e ICMP e RTP RTSP RTCP DHCP client IP filtering NTP client D Link e QoS e DNS client e CoS e DDNS client D Link e Multicast e SMTP client e ONVIF compliant e FTP client e SNMP Security e Administrator and user group protection e HTTP and RTSP authentication e Password authentication D Link DCS 3714 User Manual 61 Appendix Syste
18. by dragging your mouse in the Area window indicated by the red square Erase Motion To erase a motion detection area simply click on the red square Area that you wish to remove Right clicking on the camera image brings up the following menu options Select All Draws a motion detection area over the entire screen Clear All Clears any motion detection areas that have been drawn Restore Restores the previously specified motion detection areas D Link DCS 3714 User Manual 35 Configuration Time and Date This section allows you to automatically or manually configure update and maintain the internal system clock for your camera Time Zone Select your time zone from the drop down menu You can set the current time for the IP camera Enable Daylight Select this to enable Daylight Saving Time Saving TIME CONFIGURATION Time Zone UTC 08 00 Taipei Auto Daylight Select this option to allow your camera to configure the Daylight re ani Saving Saving settings automatically i Set date and time manually Set Date and Selecting this option allows you to configure the Daylight Saving nn a Hour Minutes Time Manually date and time manually IO VIII Y won AUTOMATIC TIME CONFIGURATION Offset Sets the amount of time to be added or removed when Daylight Saving is enabled C Synchronize with NTP Server NTP Server Synchronize with Enable this feature to obtain time automatically from an NTP serve
19. e Automatic Schedule mode Day Mode Day mode enables the IR Cut Filter 2 The default value is Automatic Save Settings Don t Save Settings Night Mode Night mode disables the IR Cut Filter Removable IR Cut filter trigger condition Schedule Mode Set up the Day Night mode using a schedule The camera will automatic sensitivity Medim lt 2ohx v 20 30 k enter Day mode at the starting time and return to Night mode atthe 6 ending time Schedule mode Day mode 24hr From 07 v 00 w To 18 w 00 v DC Power The DC 12V Power Output port can supply 12V DC 100mA of Output power to another device such as a spotlight or infrared lamp Its default setting is Off meaning it will not supply power You can d Toup select On to turn on the power supply If you choose Sync With ICR the power output will be enabled whenever the IR Cut Filter Wa is active Alternatively you can select Schedule and manually Power Output 24hr specify when the power should be enabled From 07 7 00 V To 8 V 00 V DC Power Output 12V DC 100mA D Link DCS 3714 User Manual 49 Configuration HTTPS This page allows you to install and activate an HTTPS certificate for secure access to your camera Enable HTTPS Enable the HTTPS service Secu re To enable HTTPS you have to create and install certificate first Connection Create Certificate Choose the way the certificate should be created Three options ee Create certificate
20. e secondary DNS acts as a backup to the primary DNS Enabling this setting allows your camera to be configured as a UPnP device on your network Enabling this setting allows the camera to add port forwarding entries into the router automatically on a UPnP capable network D Link DCS 3714 User Manual You can configure your LAN and Internet settings here Dont Save Stings DHCP Static IP Client IP address Subnet mask Default router Primary DNS Secondary DNS W Enable UPnP presentation C Enable UPnP port forwarding Forwarding Port Forwarding Status UPnP forwarding is inactive 25 Configuration Enable PPPoE User Name Password HTTP Port Access Name for Stream 1 3 HTTPS Port Authentication RTSP Port Enable this setting if your network uses PPPoE The unique name of your account You may obtain this information from your ISP The password to your account You may obtain this information from your ISP The default port number is 80 The default name is video mjpg where is the number of the stream You may use a PC with a secure browser to connect to the HTTPS port of the camera The default port number is 443 Choose to enable or disable RISP digest encryption Digest encryption uses MD5 hashes The port number that you use for RISP streaming to mobile devices such as mobile phones or PDAs The default port number is 554 You may specify the address of a particular s
21. e the information such as IP camera s name and time via this page You can also enable the OSD On Screen Display feature in order to display the IP camera name and time stamp for your video recordings ADMIN PASSWORD SETTING New Password 63 characters maximum Retype Password ADD USER ACCOUNT User Name 20 users maximum New Password 63 characters maximum Retype Password IP camera Name Dcs 3714 63 characters maximum W Enable OSD Label DCS 3714 30 characters maximum Show Time v 54 Configuration Backup and Restore In this section you may backup restore and reset the camera configuration or reboot the camera Save To Local You may save and document your current settings into your uc Hard Drive computer Save To Local Hard Drive Local From Local Locate a pre saved configuration by clicking Browse and then Hard Drive restore the pre defined settings to your camera by clicking Load m From Lol Hard Drive Configuration Restore To Factory Defaults Restore Factory Defaults Browse Restore to You may reset your camera and restore the factory settings by Factory Default clicking Restore Factory Defaults REBOOT Reboot Device Reboot Device Reboot Device This will restart your camera C Enable Schedule Reboot Sun Y Mon Tue M Wed Thu Fri Sat Enable Schedule Select this option t
22. ep 1 Setup LAN Settings e Step 2 Setup DDNS Settings e Step 3 IP camera Name Settings e Step 4 Setup Time Zone Back Next Cancel 20 Configuration Select Static IP if your Internet Service Provider has provided you with connection settings or if you wish to set a static address within your home network Enter the correct configuration information and click Next to continue If you are using PPPoE select Enable PPPoE and enter your user name and password otherwise click Next to continue If you have a Dynamic DNS account and would like the camera to update your IP address automatically Select Enable DDNS and enter your host information Click Next to continue Enter a name for your camera and click Next to continue D Link DCS 3714 User Manual Please select whether your IP camera will connect to the Internet with a DHCP connection or Static IP address If your IP camera is connected to a router or you are unsure which settings to pick D Link recommends that you keep the default selection of DHCP connection Otherwise click on Static IP address to manually assign and IP address before clicking on the Next button Please enter your ISP Username and Password in the case that your ISP is using PPPoE and then click on the Next button Please contact your ISP if you do not know your Username and Password DHCP Static IP Client IP address 192 168 1 100 Subnet mask 255 255 255 0 Default router 192 168 1 1 P
23. ew or modify settings or click on the Apply button if all settings are correct It is recommended to note down these settings in order to access your IP camera on the network or via your web browser IP Address DHCP IP camera Name DCS 3714 Time Zone UTC 08 00 Taipei DDNS Disable PPPoE Disable Back Apply Cancel 22 Configuration Motion Detection Setup Wizard This wizard will guide you through a step by step process to configure your camera s motion detection functions Click Next to continue Step 1 This step will allow you to enable or disable motion detection specify the detection sensitivity and adjust the camera s ability to detect movement You may specify whether the camera should capture a snapshot or a video clip when motion is detected Please see the Motion Detection section on Motion Detection on page 35 for information about how to configure motion detection Step 2 This step allows you to enable motion detection based on a customized schedule Specify the day and hours You may also choose to always record motion D Link DCS 3714 User Manual elon rma leapt ge a bree piano a persane srgies nctions To IP camera LAN or Internet ngs please click on the Back button to fpr ijn topes pan ange pe camera Setup wizard ke ks ae e Step 1 Specify Motion Detection Area Settings e Step 2 Motion Detection Schedule e Step 3 Alerts and Notifications This final step allo
24. he Dynamic DNS feature allows you to use a domain name that you have purchased www yourdomain com to access your IP camera with a dynamically assigned IP address Most broadband Internet service providers assign dynamic changing IP addresses By using a DDNS service you can enter your domain name to connect to your IP camera no matter what your IP address is Sign up for D Link s Free DDNS service at www DLinkDDNS com Save Settings Don t Save Settings DYNAMIC DNS SETTING Enable DDNS Server Address lt lt 5 v Host Name User Name Password Verify Password Timeout hours Status Save Settings Don t Save Settings 28 Configuration Image Setup In this section you may configure the video image settings for your camera preview of the image will be shown in Live Video Enable Privacy The Privacy Mask setting allows you to specify upto 3 rectangular Mask Mirror Flip White Balance Exposure Mode Denoise Brightness areas on the camera s image to beblocked excluded from recordings and snapshots You may click and drag the mouse cursor over thecamera image to draw a mask area Right clicking on the camera image brings up thefollowing menu options Disable All Disables all mask areas Enable All Enables all mask areas Reset All Clears all mask areas Mirrors the images Rotates the image 180 degrees If this option is enabled white objects will be rendered
25. installation InstallShield Wizard Complete Setup has finished installing Setup Wizard SE on pour computer Click on the D Link Setup Wizard SE icon that was created in your Windows Start menu Start gt D Link gt Setup Wizard SE 5 ShutDown O opera s r I GP windows search D Link DCS 3714 User Manual 13 Hardware Overview The Setup Wizard will appear and display the MAC address and IP address of your camera s If you have a DHCP server on your network a valid IP Address will be displayed If your network does not use a DHCP server the network camera s default static IP address 192 168 0 20 will be displayed Click the Wizard button to continue Enter the Admin ID and password When logging in for the first time the default Admin ID is admin with the password left blank Click Next to proceed to the next page D Link DCS 3714 User Manual Ana i armer OS ECURICAM Network 14 Hardware Overview Select DHCP if your camera obtains an IP address automatically when it boots up Select static IP if the camera will use the same IP address each time it is started Click Next to proceed to the next page Take a moment to confirm your settings and click Restart D Link DCS 3714 User Manual D Link 192 168 1 185 255 255 255 0 192 168 1 1 192 168 1 1 192 168 1 1 D Link 192 168 0 102 192 168 0 1 192 168 0 1 gg 15 Configuration Web based Configuration Utility
26. l pan tilt enclosure which effectively adds pan tilt functionality to the DCS 3714 An additional 12 V interface provides power for an optional LED illuminator This combination of features makes the DCS 3714 a high performance reliable and cost effective 24 hour megapixel surveillance solution System Requirements e Computer with Microsoft Windows 8 7 Vista or XP for CD ROM Setup Wizard Mac OS X or Linux e PC with 1 3GHz processor or above and at least 128MB RAM e Internet Explorer 7 or above Firefox 3 5 or above Safari 4 and Chrome 8 0 or above e Existing 10 100 Ethernet based network e ASD memory card optional is required for recording to onboard storage SDHC Class 6 or above is recommended e Broadband Internet connection D Link DCS 3714 User Manual 5 Product Overview Features High Quality Color Night Vision The DCS 3714 provides outstanding performance in low light conditions resulting in more vibrant color detail regardless of the amount of lightavailable Wide Dynamic Range Wide Dynamic Range technology corrects imperfect lighting conditions providing clear images with the right amount of contrast even when a subject is backlit Remote Monitoring Utility The D ViewCam application adds enhanced features and functionality for the DCS 3714 and allows administrators to configure and access the Network Camera from a remote site via Intranet or Internet Other features include image monitoring recording
27. le with this setting I Enable SNMPV3 Read Write Security name private Enable SNMPv3 Select whether to Enable or Disable SNMPv3 administration pa Encryption password essssssere Read Write Enter the private name in this field to enable read write access to Read oniy secwityname Security Name the network using SNMP ge my Authentication password eessssese n jon password CW Authentication Select the authentication type that matches with the remote DET Type SNMP server Authentication Enter the SNMP authentication password in this field Password Encryption Enter the SNMP encryption password in this field Password D Link DCS 3714 User Manual 52 Configuration Read Only Enter the Read only security name in this field to enable read Security Name only access to the network using SNMP Authentication Select the authentication type that matches with the remote Type SNMP server Authentication Enter the SNMP authentication password in this field Password Encryption Enter the SNMP encryption password in this field Password D Link DCS 3714 User Manual The Simple Network Management Protocol is an application layer protocol that facilitates the between exchange of management information network devices It helps network administrators to remotely manage network devices and find solve network problems with ease Don t Save Settings SNMP CONFIGURATION Enable SNMPv1 SNMPv2c Read Write community private
28. m Management General Dimensions System Requirements e Browser Internet Explorer Firefox Chrome Safari for Web Interface Event Management e Motion detection e Supports multiple SMTP and FTP servers e Event notification and uploading of snapshots video clips via e mail or FTP e Multiple event notifications e Multiple recording methods for easy backup Remote Management e Configuration accessible via web browser Take snapshots video clips and save to local hard drive Mobile Support e Windows2000 XP Vista Windows7 8 iPhone iPad Android D ViewCa m System e Operating System Microsoft Windows 8 7 Vista XP e Protocol Standard TCP IP Requirements e Web Browser Internet Explorer 7 or higher D ViewCa m Software Remote management control of up to 32 cameras e Viewing of up to 32 cameras on one screen Functions e Supports all management functions provided in web interface e Scheduled motion triggered or manual recording options Power Input e Input 100 to 240 V AC 50 60 Hz e Output 12 V DC 1 5 A Max Power PT ae Consumption D lell 0 to 40 C 32 to 104 F Temperature el Storage Temperature 20 to 70 C 4 to 158 F Humidity e 20 to 80 non condensing Weight 5459 Certifications e CE Class A LVD FCC Class A C Tick 187 1 52 9 33 5 D Link DCS 3714 User Manual 62
29. me s period Dont Save Seng Time of each file If this is selected files will be separated based on the maximum for recording length you specify RECORDING Recording entry name C Enable this recording File Name Prefix The prefix name will be added on the file name of the recording priory rama Vi file s z Source Profile 1 Vi RECORDING SCHEDULE W Sun M Mon W Tue W Wed W Thu W Fri W Sat Time Always O From 00 00 V To 23 w 59 V RECORDING SETTINGS Destination Total cycling recording size Mbytes 200 2000000 Size of each file for recording Mbytes Time of each file for recording 10 seconds File Name Prefix Dont Save Settings D Link DCS 3714 User Manual 45 Configuration SD Card Here you may browse and manage the recorded files which are stored on the SD card Format SD Card Click this icon to automatically format the SD card and create picture amp video folders View Recorded If the picture files are stored on the SD card click on the picture Picture folder and choose the picture file you would like to view Playback If video files are stored on the SD card click on the video folder and Recorded Video choose the video file you would like to view Refresh Reloads the file and folder information from the SD card D Link DCS 3714 User Manual SD Card SD Status Ready Files per Page 10 Y Refresh 1v of1 pate Fie C
30. n on page 35 In this section you can setup the IP camera s wired network interface settings If you are configuring this device for the first time D Link recommends that you dick the Setup Wizard button and follow the instructions on screen If you wish to modify or configure the IP camera settings manually click manual setup to enable the IP camera connection setup O eret Comecon Seip Wise erosi intenet Comecon Sep In this section you can setup the IP camera s Motion Detection settings If you are configuring this device for the first time D Link recommends that you dick the Setup Wizard button and follow the instructions on screen If you wish to modify or configure the Motion Detection manually dick manual setup to enable the Motion Detection setup Motion Detection Setup Wizard Manual Motion Detection Setup Internet Connection Setup Wizard This wizard will guide you through a step by step process to configure your new D Link Camera and connect the camera to the internet Click Next to continue Note Select DHCP if you are unsure of which settings to choose Click Next to continue D Link DCS 3714 User Manual This wizard will guide you through a step by step process to configure your new D Link IP camera and connect the IP camera to the internet To set up your camera motion detection settings please click Back button to dose this wizard and re open the motion detection setup wizard e St
31. ne then click the GoTo button to change the displayed camera view to the preset Clicking the Remove bution will delete the currently selected preset D Link DCS 3714 User Manual Using the Pan and Tilt controls move the camera view to the required position There are provides the tools for creating and saving Preset positions amp Preset Sequence PRESET CONTROL VIDEO PROFILE g gt ePTZ Speed PRESET Add Rename Support 0 9 A Z2 a z Prest Let V PRESET SEQUENCE Input Preset Name Preset List t T 4 Dwelltime 10 Update Second s 3 30 33 Configuration Preset This section allows you to create a preset sequence which Sequence Preset List automatically moves the camera s view between a set of preset views To add a preset to the sequence select it from the drop down box at the bottom of this window set the Dwell time to determine how long the camera view will stay at that preset then click the Add button The preset name will appear in the list followed by the dwell time to view that preset for You can rearrange your presets in the sequence by selecting a preset in the sequence then clicking the arrow buttons to move it higher or lower in the current sequence Clicking the trash can button will remove the currently selected preset from the sequence If you want to change the dwell time for a preset select it from the list ente
32. o schedule a time for the device to reboot Time 00 VJ 00 7 hh mm Reboot After making any changes click the Save button to save your changes D Link DCS 3714 User Manual 55 Configuration Firmware Upgrade The camera s current firmware version will be displayed on this screen You may visit the D Link Support Website to check for the latest available firmware version To upgrade the firmware on your DCS 3714 please download and save the latest firmware version from the D Link Support Page to your local hard drive Locate the file on your local hard drive by clicking the Browse button Select the file and click the Upload button to start upgrading the firmware Current Firmware Displays the detected firmware version A new firmware upgrade may be available for your IP camera It is recommended to keep your IP Ve rsion camera firmware up to date to maintain and improve the functionality and performance of your internet IP camera Click here D Link Support Page to check for the latest firmware version available To uparade the firmware on your IP camera please download and save the latest firmware version Current Product Displays the camera model name er Lil dr cb Name the Upload button to start the firmware upgrade FIRMWARE INFORMATION File Path Locate the file upgraded firmware on your hard drive by clicking Simmer verson 29800 B Current Product Name DCS 3714 rowse FIRMWARE UPGRADE Upload U
33. oding C Audio in off Audio in gain level C Audio out off Audio out volume level Save Settings Don t Save Settings D Link DCS 3714 User Manual 32 Configuration Preset This screen allows you to set preset points for the ePTZ function of the camera which allows you to look around the camera s viewable area by using a zoomed view Presets allow you to quickly go to and view a specific part of the area your camera is covering and you can create preset sequences which will automatically change the camera s view between the different presets according to a defined order and timing you can set Note If your View window area is the same as your Frame size you will not be able to use the ePTZ function Video Profile ePTZ Speed Arrow Buttons and Home Button Input Preset Name Preset List This selects which video profile to use You may select a value between 0 and 64 0 is the slowest and 64 is the fastest Use these buttons to move to a specific part of the viewing area which you can then set as a preset Click the Home button to return to the center of the viewing area Enter the name of the preset you want to create then click the Add button to make a new preset If an existing preset has been selected from the Preset List you can change its name by typing in a new name then clicking the Rename button Click this drop down box to see a list of all the presets that have been created You can select o
34. ording data will replace the oldest record when the total recording size exceeds this value For example if each recording file is 6MB and the total cyclical recording size is 600MB then the camera will record 100 files in the specified location folder and then will delete the oldest file and create new file for cyclical recording Please note that if the free HDD space is not enough the recording will stop Before you set up this option please make sure your HDD has enough space and it is better to not save other files in the same folder as recording files D Link DCS 3714 User Manual You can setup schedule recording to network storage with your specify week day and time period Dont Save Stings RECORDING Recording entry name _ Enable this recording Priory Source RECORDING SCHEDULE W Sun W Mon Tue M Wed W Thu W Fri W Sat Time Always O From 00 w 0 0 Vi To 23 w 59 vw RECORDING SETTINGS Destination Total cycling recording size Mbytes 200 2000000 Size of each file for recording Mbytes W seconds Time of each file for recording 10 File Name Prefix Save Settings Don t Save Settings 44 Configuration Size of each file If this is selected files will be separated based on the file size you for record i ng 2 specify meee setup schedule recording to network storage with your specify week day and ti
35. ploads the new firmware to your camera ERE D Link DCS 3714 User Manual 56 Configuration Status Device Info This page displays detailed information about your device and network connection All of your network connection details are displayed on this page The firmware version is also displayed here INFORMATION IP camera Name DCS 3714 Time amp Date Wed Jan 1 00 47 50 2014 Firmware Version 0 03 00 MAC Address 28 10 7B 1F 20 AA IP Address 192 168 1 100 IP Subnet Mask 253 290 35 0 Default Gateway 192 168 1 1 Primary DNS 192 168 1 1 Secondary DNS 0 0 0 0 PPPoE Disable DDNS Disable AES Disable TV Output Mode NTSC D Link DCS 3714 User Manual Configuration This page displays the log information of your camera You may download the information by clicking Download You may also click Logs Clear to delete the saved log information i log records IP camera events that have occurred CURRENT LOG 1 2 3 4 J 6 i 8 9 D Link DCS 3714 User Manual Fi 2014 01 01 00 46 01 admin FROM 192 168 1 2 LOGIN OK 2014 01 01 00 00 08 IP CAMERA ACQUIRE DHCP IP 192 168 1 100 2014 01 01 00 00 00 SYSTEM SET DCPOWER ON 2014 01 01 00 00 00 SYSTEM SWITCH TO DC IRIS MODE 2014 01 01 00 00 00 SYSTEM BOOTING 2014 01 01 00 00 13 IP CAMERA ACQUIRE DHCP IP 192 168 1 100 2014 01 01 00 00 01 SYSTEM SET DCPOWER ON 2014 01 01 00 00 00 SYSTEM SWITCH TO DC IRIS MODE 2014 01 01 00 00 00 SYSTEM BOOTING 2
36. put is used for connecting external alarm devices and once triggered images will be taken and e mailed Save Settings Don t Save Settings DI AND DO Digital Input 1 The active state is the current state detected is Normal Open Digital Input 2 The active state is the current state detected is Normal Open Digital Output The active state is VIDEO OUTPUT Dont Save atinge 47 Configuration RS 485 You may configure the RS 485 settings or communication specifications baud rate data bit stop bit and parity bit for your camera RS 485 is a serial communication method for computers and devices RS 485 is used to control a PAN TILT apparatus such as an external camera enclosure Support When Support PAN TILT is enabled a control panel will be PAN TILT Protocol ID Baud Rate Data Bit Parity Bit Stop Bit displayed on the Live Video page allowing control through RS 485 for an external camera enclosure Select one protocol type from the pull down menu This ID is the identifier for RS 485 devices IDs range from 1 to 255 Baud Rate is a speed measurement for communication between a transmitter and receiver which indicates the number of bit transfers per second A higher baud rate will reduce the distance of the two devices transmitter and receiver Values range from 2400 default to 19200 bps This value is the number of data bits in a transmission The data bit can be 7 or 8 default Parit
37. r kuk NTP Server C Set date and time manually Year 2014 V Month Hour 0 v Minute 47 Second NTP Server Network Time Protocol NTP synchronizes the DCS 3714 with an Internet time server Choose the one that is closest to your location Save Settings Don t Save Settings Set the Date and This option allows you to set the time and date manually Time Manually Copy Your This will synchronize the time information from your PC Computer s Time Settings D Link DCS 3714 User Manual 36 Configuration Event Setup The Event Setup page includes 4 different sections e Event e Server e Media e Recording 1 To add a new item event server or media click Add A screen will appear and allow you to update the fields accordingly 2 To delete the selected item from the pull down menu of event server or media click Delete 3 Click on the item name to pop up a window for modifying Note You can add up to four events five servers and five media fields D Link DCS 3714 User Manual There are four sections in Event Setup page They are event server media and recording Click Add to pop a window to add a new item of event server media or recording Click Delete to delete the selected item from event server media or recording Click on the item name to pop a window to edit it There can be at most 3 events and 2 recording There can be at most 5 server and 5 media configurations SERVER Name Type Addres
38. r a new dwell time then click the Update button D Link DCS 3714 User Manual Using the Pan and Tilt controls move the camera view to the required position There are provides the tools for creating and saving Preset positions amp Preset Sequence PRESET CONTROL VIDEO PROFILE we ePTZ Speed a gt VP PRESET 1 add Support 0 9 A Z a z _ GoTo Remove Input Preset Name Preset List W PRESET SEQUENCE Preset List J Preset List Preset List V Add Dwell time 10 Update Second s 3 30 34 Configuration Motion Detection Enabling Video Motion will allow your camera to use the motion detection feature You may draw a finite motion area that will be used for monitoring Enable Video Select this box to enable the motion detection feature of your 7 In order to use motion detection must first check the checkboxes then draw the areas you Motion camera ae Dont Save Seting Sensitivity Specifies the measurable difference between two sequential ppm images that would indicate motion Please enter a value between pm enable video motion 0 and 100 Percentage Specifies the amount of motion in the window being monitored fee oor ER E 0 100 that is required to initiate an alert If this is set to 100 motion is ee detected within the whole window will trigger a snapshot 0 100 Draw Motion Draw the motion detection area
39. reen will display the message Card Invalid IO Status This option displays the status of your I O device if a device has been connected PTZ Control This camera uses electronic pan til zoom ePTZ to select and view areas of interest in the field of view Please see Audio and Video on page 31 for information about setting the frame size and view window area ePTZ Speed You may select a value between 0 and 64 0 is the slowest and 64 is the fastest Global View This window indicates the total field of view FOV of the camera The red box indicates the visible region of interest ROI Language You may select the interface language using this menu The Auto Pan Starts the automatic available options are English and Traditional Chinese hm panning function The ROI will pan from back and forth within the FOV Stops the camera ePTZ motion Preset Path Starts the camera s motion along the predefined path D Link DCS 3714 User Manual 19 Configuration Setup Wizard To configure your Network Camera click Internet Connection Setup Wizard Alternatively you may click Manual Internet Connection Setup to manually configure your Network Camera and skip to Network Setup on page 25 To quickly configure your Network Camera s motion detection settings click Motion Detection Setup Wizard If you want to enter your settings without running the wizard click Manual Motion Detection Setup and skip to Motion Detectio
40. rimary DNS 192 168 1 1 Secondary DNS 0 0 0 0 _ Enable PPPoE User Name e g 654321 hinet net Password If you have a Dynamic DNS account and would like the IP camera to update your IP address automatically enable DDNS and enter in your host information below Please click on the Next button to continue Enable DDNS _ Server Address www dlinkddns com lt lt www dlinkddns com Host Name User Name Password Verify Password Timeout D Link recommends that you rename your IP camera for easy accessibility You can then identify and connect to your IP camera via this name Please assign a name of your choice before clicking on the Next button IP camera Name DC5 3714 Back Next Cancel 21 Configuration Configure the correct time to ensure that all events will be triggered as scheduled Click Next to continue If you have selected DHCP you will see a Summary of your settings including the camera s IP address Please write down all of this information as you will need it in order to access your camera Click Apply to save your settings D Link DCS 3714 User Manual Please configure the correct time to ensure that all events are triggered captured and scheduled at the correct time and day and then click on the Next button Time Zone UTC 08 00 Taipei v Enable Daylight Saving Back Next cancel Below is a summary of your IP camera settings Click on the Back button to revi
41. s Location Delete Name Status Sun Mon Tue Wed Thu Fri Sat Time Trigger Delete RECORDING Name Status Sun Mon Tue Wed Thu Fri Sat Time Source Destination aa n 3 Configuration Application In a typical application when motion is detected the DCS 3714 Network Camera sends images to a FTP server or via e mail as notifications As shown in the illustration below an event can be triggered by many sources such as motion detection or external digital input devices When an event is triggered a specified action will be performed You can configure the Network Camera to send snapshots or videos to your e mail address or FTP site Event Condition gt Action EX Motion detection Periodically Digital input System reboot Media Server what to send where to send es ex Snapshot Video Clips Email FTP To start plotting an event it is suggested to configure server and media columns first so that the Network Camera will know what action shall be performed when a trigger is activated D Link DCS 3714 User Manual 38 Configuration Add Server Configure up to 5 servers to store media Server Name Enter the unique name of your server You can set at most 5 different servers here for different event il igurati i es E mail Enter the configuration for the target e mail server account Dont Save Settings SERVER TYPE FTP Enter the configuration for the target FTP server
42. stallShield Wizard ka er der dn License Agreement Please read the following license agreement carefully Press the PAGE DOWN key to see the rest of the agreement D Link Sottware License Agreement General Terms E IMPORTANT READ BEFORE COPYING INSTALLING OR USING PLEASE READ THIS AGREEMENT CAREFULLY BEFORE USING THIS SOFTWARE D LINK SYSTEMS INC D LINE TT WILL LICENSE THE SOFTWARE TO YOU ONLY IF YOU FIRST ACCEPT THE TERMS OF THIS AGREEMENT By INSTALLING AND OR USING THE SOFTWARE YOU AGREE TO THESE TERMS IF YOU DO NOT AGREE TO THE TERMS OF THIS AGREEMENT PROMPTLY RETURN THE UNUSED SOFTWARE TO THE PARTY D LINK OR ITS AUTHORIZED RESELLER FROM Do vou accept all the terme of the preceding License Agreement If you choose No the setup will close To install Setup Wizard SE vou must accept this agreement InstallShield Back Ter Ho To start the installation process click Next InstallShield Wizard tr ko uret er Choose Destination Location Select folder where Setup will install files Note The installation may take several minutes to finish Setup will install Setup Wizard SE in the following folder To install to this folder click Next To nstall to different folder click Browse and select another folder Destination Folder C A Program Files D LinkySetupywizardS5E Browse InstallShield D Link DCS 3714 User Manual 12 Hardware Overview Click Finish to complete the
43. t of IP addresses that have no access right to the camera Remove the customized setting from the Delete List For example When the range of the Allowed List is set from 1 1 1 0 to 192 255 255 255 and the range of the Denied List is set from 1 1 1 0 to 170 255 255 255 Only users with IPs located between 171 0 0 0 and 192 255 255 255 can access the Network Camera D Link DCS 3714 User Manual 51 Configuration SNMP SNMP Simple Network Management Protocol is a widely used network monitoring and control protocol that reports activity on each network device to the administrator of the network SNMP can be used to monitor traffic and statistics of the DCS 3714 The DCS 3714 supports SNMP v1 v2c and v3 After modifying any settings click Save Settings to save your changes Enable SNMPv1 Select whether to Enable or Disable SNMPv1 or SNMPv2c a The Network Managemen layer protocol that facil the SNMPv2c administration Mati pati al Eben ee ee ee ee remotely manage network devices and find solve network problems with ease Read Write Enter the private name in this field to enable read write access to community the network using SNMP SNMP CONFIGURATION _ Enable SNMPv1 SNMPv2c Read only Enter the public name in this field to allow read only access to Read Write community private community network administration using SNMP You can view the network but Read only community public no configuration is possib
44. th User Manual and Software C CS Mount Adapter 5mm Ring Power Adapter Camera Stand If any of the above items are missing please contact your reseller D Link DCS 3714 User Manual Product Overview Introduction The DCS 3714 HD Day and Night WDR Camera with Lowlight is a professional surveillance and security solution for small medium and large enterprises The DCS 3714 uses a 1 3 megapixel progressive scan CMOS sensor which produces high quality images with low noise allowing the DCS 3714 to provide outstanding performance with color night vision in low light conditions resulting in more vibrant color detail regardless of the amount of light available The noise reduction feature has been upgraded and enhanced as well to provide a level of detail in the image quality that is unmatched by other offerings in the market In addition the DCS 3714 has Wide Dynamic Range WDR enhancement users can identify image details in both extremely bright and dark conditions The DCS 3714 has a built in removable IR cut filter for day night functionality which provides clear detail and high quality video at any hour of the day The DCS 3714 incorporates Power over Ethernet PoE and an SD card slot allowing it to be easily installed in a variety of locations The DCS 3714 input and output ports allow connectivity to external devices such as IR sensors switches and alarm relays It also comes with an RS 485 interface providing connectivity to an optiona
45. the video stream This frame will be used as a reference for the compression algorithm A higher frame rate provides smoother motion for videos Lower frame rates will result in stuttering motion The maximum number of frames that is displayed in 1 second 30 fps is the highest video quality for this camera In general any frame rate above 15 fps is imperceptible to the human eye This limits the maximal refresh frame rate which can be combined with the Fixed quality option to optimize the bandwidth utilization and video quality If fixed bandwidth utilization is desired regardless of the video quality choose Constant bit rate and select the desired bandwidth D Link DCS 3714 User Manual This section allows you to configure the sound and video of your camera You can configure different settings depending on whether you are viewing content from a PC or a Mobile Phone PDA Save Settings Don t Save Settings Warning Change the aspect ratio will dear the settings of privacy mask and preset and motion detection Save Number of active profiles Aspect ratio Default VIDEO PROFILE 1 1280x720 v 1280x720 O am v O Excellent V hd Mode Frame size View window area Intra Frame Period Maximum frame rate Video quality Constant bit rate Fixed quality VIDEO PROFILE 2 Mode Frame size View window area Maximum frame rate Video q
46. tream For instance livet sdp can be accessed at rtsp x x x x video1 sdp where the x x x x represents the ip address of your camera D Link DCS 3714 User Manual PPPOE SETTINGS Enable Disable User Name Password PPPoE Status HTTP port Access name for streami Access name for stream2 Authentication RTSP port Access name for streami Access name for stream2 Confirm password HTTPS port 443 PPPoE is inactive video 1 mjpg Configuration Enable CoS Enabling the Class of Service setting implements a best effort policy without making any bandwidth reservations C Enable CoS VLAN ID 1 Live video Enable QoS Enabling QoS allows you to specify a traffic priority policy to Live audio ensure a consistent Quality of Service during busy periods If the ceo Network Camera is connected to a router that itself implements QoS the router s settings will override the QoS settings of the Camera i 0 4095 AAR lt lt Management Enable QoS Live video Live audio Enable IPv6 Enable the IPv6 setting to use the IPv6 protocol Enabling the ae option allows you to manually set up the address specify an optional IP address specify an optional router and an optional Enable IPv6 primary DNS ee Manually setup the IP address Enable Multicast The DCS 3714 allows you to multicast each of the available ee ee der
47. uality AUDIO SETTINGS Encoding C Audio in off Audio in gain level Audio out off Audio out volume level Save Settings Don t Save Settings 31 Configuration Constant bit rate The bps will affect the bit rate of the video recorded by the camera IE Higher bit rates result in higher video quality derent stings depending on whether you are vewng content om PC or Mob Phon Fixed quality Select the image quality level for the camera to try to maintain High quality levels will result in increased bit rates VIDEO SETTINGS Number of active profiles Warning Change the aspect ratio will dear Encoding Set the audio codec to be used to G 711 or AAC This will allow you ETT ee to control the quality of audio captured at the expense of increased m Dett use of bandwidth VIDEO PROFILE 1 Mode Frame size Audio in off Ticking this checkbox will mute incoming audio View window area Intra Frame Period Audio in gain This setting controls the amount of gain applied to incoming audio ammfeme nte Video quality level to increase its volume Constant bit rate Fixed quality Audio out off Ticking this checkbox will mute outgoing audio VIDEO PROFILE 2 Mode Frame size Audio out This setting controls the amount of gain applied to outgoing audio volume level to increase its volume View window area Maximum frame rate Video quality AUDIO SETTINGS Enc
48. ult in images with less blur when viewing the camera during the night or in areas where there are low levels of light Click this button to reset the image to factory default settings D Link DCS 3714 User Manual Changes to your IP camera settings are made immediately LIVE VIDEO C Enable Privacy Mask Setting IMAGE SETTINGS White Balance Exposure Mode Denoise Brightness Contrast Saturation Sharpness WDR Level 3D filter 30 Configuration Audio and Video You may configure up to 3 video profiles with different settings for your camera Hence you may set up different profiles for your computer and mobile display In addition you may also configure the two way audio settings for your camera Number of active profiles Aspect ratio Mode Frame size View window area Intra Frame Period Maximum frame rate Video Quality You can use the dropdown box to set up to 3 active profiles Set the aspect ratio of the video to 4 3 standard or 16 9 widescreen Set the video codec to be used to JPEG MPEG 4 or H 264 Frame size determines the total capture resolution and View window area determines the Live Video viewing window size If the Frame size is larger than the Live Video size you can use the ePTZ controls to look around 16 9 1280x720 800x450 640x360 480x270 320x176 4 3 1024x768 800x600 640x480 480x 360 320x240 Select which frame in which a complete image is stored in
49. uration in seconds You can set up to ten seconds For example If the Pre event recording is set to five seconds and the Maximum duration is set to ten seconds the Network Camera continues to record for another four seconds after a trigger is activated D Link DCS 3714 User Manual 41 Configuration The moment the trigger is activated File name prefix Enter the text that will be added at the beginning of the file name VIDEOS20080104 100341 tf 1 File nume prefix Date and time suffix The format is YYYYMMDD HHMMSS D Link DCS 3714 User Manual 42 Configuration Add Event Create and schedule up to 3 events with their own settings here Event name Enter a name for the event You can set at most 3 events like motion detection or digital input trigger here and arrange the detection schedule at the same time Enable this Select this box to activate this event event EVENT Event name Priority Set the priority for this event The event with higher priority will be enable this event executed first Priority Delay for seconds before detecting next event For motion detection and digital input Delay Select the delay time before checking the next event It is being ELGI used for both events of motion detection and digital input trigger Video motion detection O Periodic n igger every minutes Trigger Specify the input type that triggers the event O ris m O System boot Video
50. ws you to specify how you receive notification of camera events Choose between an notification or alternatively you can setup an FTP Notification You will need your email account settings o details If you are unsure of information please contact your ISP Once you have entered this arali please dick on M sun Mi Mon W Tue M Wed M Thu M Fri M Sat Time Always O From 00 v 00 v To 23 v 59 v Back Next Cancel 23 Configuration Step 3 This step allows you to specify how you will receive event notifications from your camera You may choose not to receive notifications or to receive notifications via e mail or FTP Please enter the relevant information for your e mail or FTP account Click Next to continue Step 4 You have completed the Motion Detection Wizard Please verify your settings and click Apply to save them Please wait a few moments while the camera saves your settings and restarts D Link DCS 3714 User Manual This final step allows you to specify how you receive notification of camera events Choose between an email ification or alternatively you can setup an FTP Notification You will need your email account settings or FTP details If you are unsure of this information please contact your ISP Once you have entered this information please click on the Next button O Do not notify me Email Sender email address Recipient email address Server address User name Password
51. y is a form of error checking used in serial communication For even and odd parities the serial port sets the parity bit the last bit after the data bits to a value to ensure that the transmission has an even or odd number of logic high bits For example if the data is 011 for even parity the parity bit is 0 to keep the number of logic high bits even If the parity is odd the parity bit is 1 resulting in 3 logic high bits Parity can be set to No none Even and Odd The stop bit is used to signal the end of communication for a single packet The more bits used for stop bits the greater the lenience in synchronizing the different clocks but the slower the data transmission rate The stop bit can be set to 1 or 2 The default value is 1 D Link DCS 3714 User Manual This section enable you to specify the camera RS 485 settings Don t Save Settings L Support PAN TILT Protocol ID Baud Rate Data Bits Parity Bit Stop Bit Save Settings Don t Save Settings RS 485 Pin Block 48 Configuration ICR You may configure the ICR settings here An IR Infrared Cut Removable ICR filter can be disengaged for increased sensitivity in low light environments Automatic The Day Night mode is set automatically Generally the camera uses Day mode and switches to Night mode when needed Arge op cme deg rer ambient light allowing the camera to be effective in day night environments a keel sys The available options ar

User Manual - D-Link

Contents

Download Pdf Manuals

Related Search

Related Contents