to view PDF of Riflescope User Manual, SM13011
Contents
1. a bolt action rifle remove the bolt When mounting to a semi automatic rifle disassemble the rifle until there is a straight line of sight through the bore or use several mirrors for the same effect Now use a target at least 50 feet away when sighting in the riflescope Look through the bore of the weapon and locate the target Sight in the target through the bore and then adjust the riflescope If the riflescope is significantly off target take the rifle and riflescope to a certified gunsmith to check for correct mounting and alignment After boresighting the weapon it will need to be fine tuned to compensate for bullet drop and other variables Please take the time to fine tune the weapon to ensure it is accurate RE ZEROING WINDAGE AND ELEVATION KNOBS Once the riflescope has been sighted in it is time to reset the windage and elevation knobs back to zero Please refer to the directions below based on the type of turrets on the riflescope Riflescopes with locking turrets Use a 1 5mm metric hex wrench to loosen the three set screws located along the scalloped edge of the elevation turret Next lock down the locking thumb screw on top of the knob Then rotate the knob and set the MOA hash marks back to zero Once the knob is zeroed retighten the three set screws making sure not to over torque and strip them After all three set screws are sufficiently tightened the mechanism will re engage Repeat these steps for the windage turret R2. details and information 10 SIGHT MM an www sightmark com
3. in losing the riflescope due to a multitude of reasons i e sending it to the wrong address and other problems associated with unexpected packages 1 Make sure the parallax if equipped was set at the correct range 2 Check the mount Make sure the riflescope is mounted securely to the rifle Try with bare hands only to gently twist the scope in the rings or see if anything moves when it is jiggled If there is any movement retighten the mounting system according to the mounting instructions but do not over tighten as this could cause a misalignment of the internal optical parts 3 Make sure the action of the firearm is properly bedded in the stock and that all receiver screws are tight and have been tightened in the sequence recommended by the manufacturer A loosely fitted stock can cause changes to the point of impact 4 When test firing a rifle to check the point of impact relative to windage and elevation adjustments be sure to fire from a solid bench with sandbags supporting the forearm and buttstock 5 Be sure to use factory loaded ammunition of the same bullet type weight and preferably lot number when sighting in the riflescope If one type of ammunition does not shoot well try another brand or bullet weight 6 Be certain that both the barrel and chamber are clean Heavy factory grease or copper fouling on older rifles can diminish the accuracy of the firearm SIGHTMARK WARRANTY Please visit www sightmark com for warranty
4. JE NG K USER MANUAL RIFLESCOPES Triple Duty amp Tactical Series English Francais Espa ol Deutsch ABOUT SIGHTMARK Sightmark offers a wide range of products that include red dot scopes reflex sights rangefinders riflescopes laser sights night vision and award winning flashlights and boresights Sightmark products are inspired by military and lawenforcement applications All products are designed to be the most effective weapon accessories possible Sightmark MAKE YOUR MARK SIGHT mark 4 A TA Ag Ea ET EM A ION a Ni w jr pe 1 gt gt ae La p P a tl a i Di Aria Ae N 7 Bau at ae rn g ai i 3 EA x 5 ar ra FE Y Ly Pa Mi Cha F r Ebo pas t Ark A VPI ar Aight ae x y pr da ve ABOUT THE SIGHTMARK TRIPLE DUTY amp TACTICAL SERIES OF RIFLESCOPES The Sightmark Triple Duty Series and Tactical Series of riflescopes use cutting edge glass and lens coatings to ensure that it is the most accurate riflescope in its class Precision multicoated optics are a distinguishing feature of the Sightmark Triple Duty riflescope line multicoated lenses offer a clear view for easy target acquisition in both bright and low light situations Both waterproof and fog proof the nitrogen filled Sightmark Triple Duty Series features oversized windage elevation and parallax adjustment knobs for easy adjustment in the field Locking mechanisms on the windage and elevation
5. adjustments ensure that the scope stays zeroed Internal lit Mil Dot reticles help shooters successfully make accurate shots over a wide range of distances and lighting conditions available on select models DIAGRAM Objective lens 9 Windage adjustment Elevation adjustment Magnification ring Diopter adjustment Eyepiece assembly Side parallax adjustment Reticle illumination adjustment Windage Elevation lock 10 Mil Dot reticle NO CON AUN BRWDN gt available on select models SPECIFICATIONS FEATURES Precision accuracy Locking turrets Mil Dot reticle Wide field of view Precision multicoated optics Phase corrected coating Internal lit reticle 1 8 locking MOA adjustments Parallax adjustment Front diopter adjustment Nitrogen purged Lightweight Waterproof Shockproof Fog proof available on select models Eyepiece diameter mm Field of view m amp 100m Exit pupil mm Eye relief mm Phase corrected anti reflective coating Parallax yards Waterproof nitrogen filled yes no Reticle Illuminated reticle One piece tube diameter mm MOA Diopter Windage Elevation MOA one click in Windage Elevation lock yes no Focal plane Length in 4x32 Tactical 6x42 Triple Duty J DS 2 IR rs N 00 o O q Uy 92 7 Wide Band AR Green n Ww mm mm cnm e gt
6. ceives it Be sure to adjust the parallax knob to the correct shooting range It is very important to keep this in mind when zeroing the rifle If this is not taken into consideration at the time of sighting in the riflescope accuracy will diminish DIOPTER ADJUSTMENT The diopter is the measurement of the eye s curvature People s eyes are all curved differently Sightmark riflescopes have a diopter adjustment that helps attain the perfect shot Once parallax has been adjusted rotate the diopter adjustment ring for the clearest view This adjustment should stay the same unless the riflescope s operator changes available on select models MIL DOTS All Sightmark riflescopes come with a Mil Dot reticle Mil stands for millradian A millradian is 1 6283 2th of a circle or 3 438 MOA The millradian represents 1 unit at 1000 yards To simplify a target that is one yard tall at 1000 yards would measure 1 millradian Sightmark s Mil Dot reticle is the NATO standard Mil Dot which differs from the 34 USMC reticle In order to accurately range using the Mil Dot system the target size must be known For example a full size deer is approximately six feet long Transfer the feet into yards 3 1yd so the deer is 2 yards long Now measure the deer in the crosshairs it is 4 mils long Then divide the size of the deer by the Mils 2 4 0 5 then multiply 0 5 by the constant of 1000 This equals 500 So the deer is roughly 500 yards away Fi
7. gt T gt T gt INSTALLATION It is recommended to have the riflescope mounted by a professional gunsmith However if attempting to mount the riflescope without professional assistance please read and strictly adhere to the following directions 1 All riflescopes come with basic rings for immediate mounting 2 Unload the weapon Remove the bolt firing pin to ensure the weapon is incapable of firing 3 Install the lower portions of the rings onto a Weaver base Tighten the screws to between 45 65 inch pounds of torque 4 Place the riflescope in the rings and install the top portion of the rings loosely so that the riflescope can move freely 5 Establish the correct eye relief by moving the weapon into the shooting position While in the shooting position move the riflescope so that very little black can be seen while looking through the riflescope 6 Once eye relief is established check the crosshair alignment by pointing the riflescope at an object that is level and align the crosshair 7 Once the alignment is checked tighten the rings evenly Take care not to over tighten the screws as this could bend the scope base attatchment screws amp ring top screws 15 inch Ibs ring cross bolt nut 68 inch Ibs 8 Check alignment and position then boresight the riflescope BORESIGHTING Using a Sightmark laser boresight is the most accurate and convenient way to sight in a riflescope When mounting the riflescope on
8. iflescopes without locking turrets Use a 1 5mm metric hex wrench to loosen the three set screws located along the scalloped edge of the elevation knob Next rotate the knob to set the MOA hash marks back to zero Once the knob is zeroed re tighten the three set screws making sure not to over torque and strip them After all three set screws are sufficiently tightened the mechanism will re engage Repeat these steps for the windage turret sT w P ZEROING PROBLEMS Sightmark s Triple Duty scope line comes with locking turrets that do not need tools for adjustment These locking turrets are designed to make adjustments on the fly It is possible for a weapons mounting system to not be level with the bore which makes it nearly impossible to adjust zero In this case it is recommended that adjustable rings or a shim be used in order to raise the rear of the scope effectively leveling it to the bore of the weapon to attain zero MAGNIFICATION Some Sightmark riflescopes come equipped with variable magnification options Simply turn the dialto the setting desired Note The higher the magnification the smaller the fleld of view becomes PARALLAX ADJUSTMENT Sightmark s higher magnification riflescopes do come equipped with a parallax adjustment knob Parallax is the change of angular position of two stationary points relative to each other as seen by an observer In other words it s how the image lines up in the riflescope and how the eye per
9. nally adjust the riflescope s elevation for accuracy ILLUMINATED RETICLE Some riflescope models are equipped with an illuminated reticle When using the illuminated reticle use the lowest brightness setting possible This will make ranging targets much more effective CHANGING BATTERIES 1 Make sure the firearm is unloaded and pointed in a safe direction 2 While holding the illuminated reticle battery housing unscrew the top portion of the cap 3 Remove the CRV2032 3volt battery and replace it while noting the polarity Be sure the polarities of the battery match with the positioning displayed on the diagram located in the battery housing 4 Replace the top portion of the cap MAINTENANCE Proper maintenance of the riflescope is recommended to ensure longevity It is recommended that when the riflescope becomes dirty that it is wiped down with a dry or slightly damp cloth Blow dirt and debris off all optics and then clean lenses with a lens cleaning cloth No further maintenance is required WARNING All Sightmark riflescopes are nitrogen purged and o ring sealed unless otherwise noted Do NOT disassemble the riflescope for any reason as this will void the warranty and could be hazardous Any internal work should be handled by the manufacturer Any tampering with the purge screw will void the warranty O TROUBLESHOOTING Never ship back a riflescope without getting proper authorization beforehand Doing so could result
Download Pdf Manuals
Related Search