COOKER HOOD - Premier Range
Contents
1. Fix hole Glass shutter Positioning hole Fixing pole Step 8 1 Draw the inner duct cover up to the suitable height and mark on the wall two keyhole of the outer duct cover bracket with a pen 2 Put down the inner duct cover gently drill the keyholes in 60 70 mm depth on the horizontal level using 8mm drill 3 Press the expanding tube provided into the holes 4 Match the inner duct cover with the holes and tighten the inner duct cover with two 5x60 wood screws provided Step 9 Extend the air outlet of the exhaust pipe to the outside Try to make the bend of the exhaust pipe to more than 120 Step 10 Install grease filter Match the fix pin to the fix hole and button the filter gently as the direction of arrow A Step 11 Block the positioning hole on the glass shutter with the fixing pole pull the glass shutter up or down to fix it2. Fig 4 3 Clean the aluminium filter once a week or according to the extent of the usage Press the buckle ofthe aluminium filter lightly take off the aluminium filter and putit into warm soapy water using mild detergent wipe the aluminium filter with soft brush Replace the filter after itis dry 4 Clean the motor fan and other inside parts once every halfa year or according to extent ofusage bya QUALIFIED PERSON 5 DONOT clean motor with water or any other liquid Clean the blower assembly Blower assembly Blower fixed screws Blower assembly Fig 1 1 Take out the filters 2 Loosen the wire insert and power supply wire 3 Loosenearth wire 4 Loosen blower fixed screws 5 Take out the blower assembly Fan fixed screws Motor fix cover Charcoal filter Blower assembly Fig 2 8 OPERATINGINSTRUCTION 1 Howto use the softtouch control ABC DEF MONOS 55 55 FORORO A Touch A the fan runs at the low speed Press itagain the fan turns off B Touch B the fan runs atthe mid speed Press it again the fan turns off C Touch C the fan runs atthe high speed Press it again the fan turns off A By C three bottons interact D Whenthe hood is OFF press and hold D for 3 seconds and then press C and D to adjust the hour and minute respectively G acts like a clock On the screen left side is hour and the righ
3. 3 5 110V an7 120 V 280mm 405mm 16 IMPORTANT SAFETYINSTRUCTIONS Do not connect the air outlet to chimney pipes or combustion gas ducts Do not leave naked flames under this hood In case of any damage to power cable replace the broken cable with a new one by qualified person Do clean the hood correctly in accordance with instruction stated or it might cause the possibility of fire accident Replacement of bulb should be undertaken by a qualified electrician or a competent han Always use bulb that ae not more than 2 10 6 Take outthe charcoal filter by turning itanti clockwise direction according tothe arrow shown ifyou haveinstalled charcoal filter 7 Take out the motor fix cover like arrowhead s direction 8 Use hexangular screwdriver to loosen the blower fix screws 9 Take out the fan 10 Do the same to take out the other fan 11 After itis cleaned please assemble it inthe reverse steps of loosening it See Blower assembly Fig 2 Note Left motor fixed cover and fan havea little difference don t assemble itin wrong side TO REPLACE LIGHT BULB CAUTION LAMP UNIT MAY BE HOT WAIT UNTIL UNITIS COOL ANDUSE THE SAME TYPE OF LIGHTBULB Make sure all control switches are off and range hood is unplugged Pls follow below instructions Warning Make
4. ccccec ee cec eee eeeeeeeen ees 9 10 MAINTENANCE ciu a 10 11 Never pull the plug out of the power supply with CLEAN THE BLOWER en ne 11 wet hand to avoid the possibility of electric shock TO REPLACE LIGHT BULB 12 IMPORTANT SAFETY INSTRUCTIONS 13 14 Disconnect the cooker hood from the TROUBLE SHOOTINGS usssssesseeeneneenesaneenennene nennen 15 power supply if this appliance will not be used for a long time Please notethat thisproduct ismarked withthis symbol E According to Wasteof Electrical and Electronic Equipment WEEE directive WEEE should be separately collected and treated Ifat any timein futureyou needto disposeof this product Pleasedo NOTdispose ofthis productwith household waste Please send this product to WEEE collecting points where available 11 Dear consumer Thanks for your purchasing our cookerhood and we hope we can fully satisfy allyour needs Please readall instructions carefully before proceeding to obtain the best results of using the cooker hood TECHNICAL CHARACTERISTICS Model No Total power 254W Motor speed 250W LED Lights 2 x2W RS C902 LIRS C902 60 Voltage _1220 V 230 V 240 V Frequency 50 Hz 60Hz Filter 6 layer filter Control Inductive Switch BODY SIZE 298mm 11 3 5 IR Eg SN la ze 900 600mm 36 23
5. sure the bulb has cooled before you touch it 1 Take out the aluminum filter and cut offthe wire connection 2 Press the spring according to the arrow direction so as to put off the bulb cup 3 Replace the old bulb with anew 2W one 4 Put on the new bulb in reverse direction then fix the spring and wires MAIN PARTS NAME 1 bracket 2 Inner ductcover NS E losa 3 Outer ductcover 4 Exhaust pipe 5 Blower box 6 Glass Panel 7 Aluminium Filter 8 Glass shutter INSTALLATION REQUIREMENT 1 Do not install the cooker hood where there are many doors or windows in order to avoid affecting the exhaust efficiency of the hood caused by airconvection Fig 1 2 Install the cooker hood right above the hob The recommended distance between the hob and the lower edge of the cooker hood is minimum 650mm andmaximum 700mm Fig 2 w In order to get the optimum performance do not lengthen the exhaust pipe too long nor try to bend the exhaust pipe to be biggest ensure the connection is airproof Fig 3 4 After hanging the unit on to the wall ensure the hood is level and vertical Fig 4 The air outlet must not be connected to chimney pipe or combustion gas Nn ducts The air outlet must in under no circumstances be connected to ventilation ducts of room in which fuel burning appliances are installed Fig 1 Fig 2 Fig 3 650 700mm
6. COOKER HOOD TROUBLE SHOOTINGS CAUTION Disconnectthe power supply before servicing STATUS CAUSE AND METHOD OF REPAIRING TOOL The power supply is damaged Ifthe power supply isdamaged please callthe technicians to repair pn type Screwdriver Sharp Pincers The lamp works but the motor does not run a Remove the vane guard and rotate the vane by hand If the vane cannot move smoothly the core or bearings of the motor may be damaged In this case replace with a new motor b Check the connection between air exhaust pipe and wind chamber leaks oil or not If YES pleasg fill it up with varnish or thinner c If the starting wire yellow is disengaged from the condenser itneeds to be rewired d If the condenser is damaged replace with a new one min type Screwdriver The lamp works but the motor does not run a Take off the filterand check the connection between air inlet and wind chamber is sealed or not b Check the connection between air exhaust pipe and wind chamber leaks oil or not If YES please fill it up with varnish or thinner min type Screwdriver Machine vibration a If the motors are not firmly screwed screw tigh ten them up b If the vane is damaged or unbalanced replace with a new one man type Screwdriver Weakness suction a The distance is too far between the Range Hood and the Gas Cooker b There are many windows doors cause wind
7. con vection is too strong c If the Range Hoodis set upon the win dow the best solution is to put one three ply board on the back of the Range Hood to cover the hollow of window min type Screwdriver Installation of the model is tilt a Adjust the height of the model where is hang on the ceiling b If the model tilt forward lock into the wall with wood screw again the screw peep out around 0 5 1 cm from the wall or check the screws for fix ing the model are loose or not y type Screwdriver Bulb does not light Just screw off the lamp shade and replace with a new bulb then put the lamp shade back p type Screwdriver 12 Wearprotective glove before you start to READ AND SAVE THESE INSTRUCTIONS MANUAL clean the hood Remove the components gently during cleaning CONTENTS TECHNICAL CHARACTERISTICS ou ccec ee eeeeee es 1 Never wash the control switch with water or other kind of liquid to avoid VA e AO E E GER EUER N NEEREDEEEISNEERESREER SEERERSEEREREERAE 1 2 electrical problem to thehood MAIN PARTS u nennen AEAEE ENR ran 3 4 INSTALLATION REQUIREMENT ceeeesenesenen 4 5 Cleaning of motor fan should be undertaken by a qualified person pay close INSTALLATION PROCEDURES cunssceesssenesenensenenen 6 8 attention to avoid any distortion of the fan during cleaning OPERATING INSTRUCTION ce
8. e provided into the holes Tighten the wood screws of 5x60mm which is supplied together with the hood to the expanding tube Make sure itis tight enough and cannot be move Step 3 Hang the cooker hood to the 2 wood screws Tighten the 2 wood screws from the position ofthe filters to the expanding tube Ifthe hood has little upward or downward slope use the adjustable screws to adjust it to be level Fe has pipe Air outlet we a Bracket Inner duct cover Inner duct cover l Outer duct cover A Orientation Slot Inner duct cover Outer duct cover Fix screws Step 4 Take out the cooker hood from the carton and putit ona horizon tal work table gently Fix the reducer pipe into the air outlet of the inner duct and then fix the exhaust pipe into the top ofreducer make sure it is connected to the reducer tightly Step 5 Matching the bracket to the holes of the inner duct cover and fix it well with M4 screws Step 6 Insert the inner duct cover into the outer duct cover Do note that the inner duct cover must be fixed to the outer duct cover s orientation slot Step 7 Put the outer duct cover to the unit body and use two M4x10 screws to fix the outer duct cover to the unit body Expanding Tube
9. t side is minute When the hood is operating touch Dto control working time of hood 5 minutes per onetouch the longest stay ON timeis 1 hour E Press E turns on the light Pressit againto turn off the light F Whenthe hoodis operating press F the hood will not be OFF at once 1t will remain for one minute before itis OFF MAINTENANCE CAUTION NEVER PUT YOUR HAND INTOTHE AREA HOUSING THE FAN WHILE THE FAN IS OPERATING FOR THE OPTIMAL LEVEL OF OPERATION CLEAN THE RANGE HOOD SURFACE FAN AND ALUMINIUM FILTER REGULARLY 1 Use only mild soap or detergent solutions to clean the cooker hood surface Dry surfaces using soft cloth 2 Using a stainless steel cleaner to bring the glow back into a stainless steel finish INSTALLATION PROCEDURES SAFETY WARNING HOOD MAY HAVE VERY SHARP EDGES PLEASE WEAR PROTECTIVE GLOVESIF ITIS NECESSARYTO REMOVE ANY PARTS FOR INSTALLING CLEANING OR SERVICING Expanding Tube 5x60 Wood Screw Hook Adjustable screw Step 1 Fix the position ofthe cooker hood in accordance with therecommend ed height between 700 mm to 750 mm 27 3 5 29 1 2 from the hob and the lower edge ofthe hood Step 2 Drill 4 holes in perpendicular to the wall with 8mm in diameter and 60 70mm in depth Pressthe 4 expanding tub
Download Pdf Manuals
Related Search