USER`S MANUAL - - Office Equipment Machine Shop
Contents
1. 4 2 Drill Bit Removal and Installation CAUTION DRILL BITS MAY BE HOT AFTER USE ALLOW DRILL BITS TO COOL DOWN BEFORE TOUCHING BEFORE REMOVING OR INSTALLING THE DRILL BITS DISCONNECT OR LOCK OUT THE POWER SUPPLY Diagram 4 20 4 2 1 We recommend using a piece of card stock on the Table when leveling the drill bit to avoid drilling into the drill strip This will lengthen the life of your drill bits and keep them sharper 4 2 2 Remove the hole guard which is attached to the chuck This is done by grasping the bent end and sliding the guard off 4 2 3 Using the Chuck Release Key EBM 32 insert the tapered end facing down into the chuck hole With a clockwise motion turn the Chuck Release Key 45 degrees The drill bit will slide out of the chuck Itis recommended that you hold onto the drill bit so that it does not drop out of the chuck damaging the tip Diagram 4 30 4 2 4 To install a drill bit grasp the drill bit and being careful to keep it straight press it up into the chuck Chuck 5 Hole Guard 4 2 5 Seat the drill bit by using a stack of scrap paper Set the scrap on the table Step on the foot pedal slowly raising the table toward the Drill Bit Put light pressure on the hollow Drill Bit seating it firmly in place prl Bit 4 2 6 Remove the scrap paper and turn the machine on to check the concentricity of the bit If the bit is not concentric remove it and repeat steps 4 2 2 through 4 2 5 unt2. Page 06 the serial number when you call e 3 4 Installing the Paper Side Stops Page 06 e 3 5 Installing the Chip Bag precaire n inni Page 07 e If you wish to write to us send correspondence to e 3 6 Choosing and Installing the Pattern Bar sie seen Page 07 Lassco Wizer e 3 7 Electrical Instructions Page 07 Attn Customer Service 485 Hague Street Rochester NY 14606 4 Operation e4 1 Protective Guard Page 08 e 4 2 Drill Bit Removal and Installation Page 08 Sores z 4 3 Leveling the Drill Bifs Page 09 1 2 Shipping Damage Inspection e 4 4 Adjusting the Back Gauge Page 09 e Remove the machine from the carton and inspect for 4 5 Drilling Procedures Page 10 any shipping damage If any damage is present report 46 Traversing the Table Page 10 the damage to the carrier immediately failure to do so 4 7 Tips on Drilling Page 10 may void any warranties 5 Maintenance O51 Safety needa cessed Page 11 e 5 2 Annual Lubrication eee Page 11 6 Trouble Shooting Guide e 6 1 Determining the Cause and Correction to Certain Problems Page 12 7 Parts Diagrams e7 1 Front Rear and Side Views Page 13 7 2 Internal Views Page 14 7 3 Parts List Page 15 Page 01 2 Safety 2 1 Safety Instructions All operators m
3. Tighten Machine is sitting on eneven surface Reposition drill to obtain concentricity Drill bits are out of concentricity Reinstall drill bits to obtain concentricity Drill bit drills into drill strip drill bits not drilling through bottom sheet of paper Drill bit was not adjusted to card stock card stock not used Adjust per Operating Instructions Operator not allowing full travel of table Drill per Operating Instructions through full drilling cycle Table pivots front and back Table guides are out of adjust ment Loosen the two screws holding the table guides located on the sides of the upright and readjust Page 12 7 Parts Diagrams 7 1 Front Rear and Side Views OS 35 2 Page 13 7 Parts Diagrams 7 2 Internal Views Qw Page 14 7 Parts Diagrams 1 EZ 108A Handle Assembly 2 FM5 5006 Rocker Switch On Off 3 EZ 117A Shroud Assembly 4 FM5 5003 Chuck 5 FM5 5011 Chuck Release Guard 6 Ho
4. Lassco Wizer Spinnit EBM 2 1 manual Paper Drill Serial Number Date of Purchase Dealer Address Before operating this equipment please read these instructions completely and keep these operating instructions for future reference Telephone Number Lassco Wizer 485 Hague Street Rochester NY 14606 U S A Tel 585 436 1934 Fax 585 464 8665 www lasscowizer com info lasscowizer com Table Of Contents 1 Introduction 1 Introduction 1 1 Your New EBM 2 1 Paper Drill e 1 1 Your New EBM 2 1 Paper Drill Page 01 e Thank you for your purchase of the Spinnit EBM 2 1 e 1 2 Shipping Damage Inspection Page 01 Paper Drill e We ask that you take a moment to fill in the serial number and other information on the front cover of the e 2 1 Safety Instructions Page 02 manual Please keep this manual as a reference for 2 2 WarningLabels Page 03 future use e 2 3 Grounding Instructions Page 04 e For parts and service please contact the Lassco Wizer 3 Setting Up Your Machine Dealer from whom you purchased the machine If you require assistance in locating a Lassco Wizer Dealer e 3 1 Loose Items Inventory A Page 05 please contact our customer service department at 585 e 3 2 Accessories WA rin pisoi asagi Page 05 436 1934 Please have the model of your machine and e 3 3 Installation of the Back gauge
5. hould be made by qualified service personnel and after reconnection the tool should comply with all local codes and ordinances Page 04 3 Setting Up Your Machine 3 1 Loose Items Inventory e Please remove and inspect the following items FM4 4006 Paper Side Stops 2 FM4 4007 Side Stop Screws 4 a ae a a di ee ea a dada D ay EZ 115A Back gauge 1 EBM2 1048 Chip Bag 1 EZ 1016 Pattern Bars set of 4 Spin eze DRILL EASE U DRILL EASE Drill Bit Lubricant 1 Hollow Drill Bit 1 SPIN EZE Drill Bit EBM 32 Chuck Re these items may be Lubricant 1 lease Key 1 installed ESS LJ U U EBM2 1034 16 Drill Strip 1 HEX 18 Hex Wrench HEX 332 Hex Wrench CC 2 Chip Clearer 1 1 8 1 3 32 1 3 2 Accessories Warning e USE RECOMMENDED ACCESSORIES Only use accessories approved by a Lassco Wizer The use of improper acces sories may cause risk of injury to persons Page 05 3 Setting Up Your Machine 3 3 1 Attach the Backguage to the Table by hooking the left end over the Side Iron FM4 4003 on the side as shown in the accompanying picture Align both ends of the Backgauge using the Table Scales 3S 14 so that it is squared correctly When it is positioned as desired tighten down the Clamp Bracket Knob as shown Diagram 3 60 3 3 2 Do n
6. il it is concentric Diagram 4 40 4 2 7 When the drill bit is correctly installed replace the hole guard back onto the chuck to protect debris from clogging the chuck Page 08 4 Operation 4 3 Leveling the Drill Bits 4 3 1 4 3 2 4 3 3 4 3 4 4 3 5 4 3 6 We recommend using a piece of card stock on the Table when leveling the drill bits to avoid drilling into the drill strip This will lengthen the life of your drill bits and keep them sharper To level the drill bit to the Table follow steps 4 3 3 through 4 3 5 Loosen the Leveling Knob on the right hand side of the ma chine Pull down on the Handle to raise the Table until the hollow drill bit is just touching the Drill Strip EBM2 1034 Hold the Handle in place and tighten down the Leveling Knob until it hits the Handle Bracket This will stop the Handle from being pulled down too far It is important to always level the drill bit before each use and after sharpening This will make sure you don t drill into the Drill Strip dulling the hollow drill bit Diagram 4 40 4 4 Adjusting the Back gauge 4 4 1 4 4 2 4 4 3 4 4 4 4 4 5 Adjust the Back gauge so that it is the correct distance from the edge of the product to the center of the hole to be drilled by per forming the following Loosen the Clamp Knob on the right side of the Back gauge Using the two 2 Scales embedded
7. in the rear corners of the table align the front edge of the Back gauge with the desired distance Zero 0 on these scales align with the center of the hollow drill bits Tighten down the Clamp Knob when the Back gauge is positioned as desired Diagram 4 50 Page 09 4 Operation 4 5 Drilling Procedures 4 5 1 When you are ready to drill set the product to be drilled on the table and make sure it is secure using the Paper Side Stops Turn the machine on and holding the product firmly in place with one hand pull down on the Handle raising the Table up to meet the y drill bit Using one consistent smooth stroke put pressure on Diagram 4 60 the Handle so that the Table rises fully allowing the drill bit to drill 5 through the product It is important you maintain a consistent speed through the entire stack It is also important you do not go too slow or too fast If you drill too slow you can burn the paper leaving undesired marks If you drill too fast the drill bits will act more like a punch and they will break or plug 4 6 Traversing the Table 4 6 1 To move the Table to the next desired hole on the pattern bar press in on either of the Release Handles EZ 1010 located on both ends of the table Pressing in the Release Handle releases the Release Pin allowing the table to tra verse Release the Handle and s
8. ired pattern into the slot on the Pattern Bar Guide as shown in diagram 3 110 Insert the angled end into the slot as far as it will go so that the slot at the end of the Pattern Bar lines up with the Pattern Bar Stop When you have the pattern correctly inserted tighten down the Pattern Bar Stop through the slot on the Pattern Bar locking it in place 3 7 Electrical Instructions 3 7 1 Your EBM 2 1 comes with an electrical cord containing the plug to Diagram 3 120 fit into a standard grounded 115V outlet This machine has a full load draw of 5 5 Amps Power Cord Fa 3 7 2 Making sure that nothing is interfering with the drill bits plug the cord set into a grounded 115V outlet To turn the machine on press the Rocker Switch on the front of the shroud z CD Rocker Switch 4 Operation 4 1 Protective Guard 4 1 1 Your EBM 2 1 comes with a protective guard installed DO NOT Diagram 4 10 operate this machine without the guard in place 4 1 2 Please note that when you are performing certain operations such as removing and installing drill bits you will need to move the guard out of the way Making sure the power to the machine is disconnected or locked out push the guard up and hold in place while performing necessary operations or maintenance The pro tective guard should not be removed during operation
9. ith an electric cord having an equipment grounding conductor and a grounding plug The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances DO NOT MODIFY THE PLUG PROVIDED If it will not fit the outlet have the proper outlet installed by a QUALIFIED ELECTRICIAN Improper connection of the equipment grounding conductor can result in a risk of electric shock The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment grounding conductor If repair or replacement of the electric cord or plug is necessary do not connect the equipment grounding conductor to a live terminal Check with a QUALIFIED ELECTRICIAN or service personnel if the grounding instructions are not completely understood or if in doubt as to whether the tool is properly grounded Use only 3 wire extension cords that have 3 prong grounding plugs and 3 pole receptacles that accept the machine s plug This machine is intended for use on a circuit that has an outlet that looks like the one illustrated in diagram 2 10 The machine has a grounding plug that looks like the plug illustrated in diagram 2 10 Make sure the machine is connected to an outlet having the same configuration as the plug No adapter is available or should be used with this machine If the machine must be reconnected for use on a different type of electric circuit the reconnection s
10. lide the Table until it locks into place in the next desired position Diagram 4 60 Table d u Release Handle Release Handle Na e 4 7 Tips on Drilling 4 7 1 Use a sharp drill bit at all times Using a drill bit sharpener sharpen your drill bits regularly Apply light pressure when sharpening Too much pressure may cause flaring of the tip Once a drill bit has a flared tip it becomes defective 4 7 2 Sharpening Stone Use to debur the outside cutting edge of the drill bits for better performance 4 7 3 Lubricate drill bits occasionally Use Drill Ease or Spin Eze While the drill is running simply touch the Drill Ease stick to the drill bit or brush on the Spin Eze Drill through scrap to remove any excess This will allow for a smoother cut 4 7 4 Drill Strips When drilling a drill bit must stop slightly above the drill strip Replace worn out drill strips regularly to ensure proper drilling Page 10 5 Maintenance ALWAYS DISCONNECT THE POWER BEFORE PERFORMING MAINTENANCE ON THIS MACHINE MAINTENANCE SHOULD ONLY BE PERFORMED BY A QUALIFIED TECHNICIAN 5 2 Annual Lubrication 5 2 1 Lubricating your EBM 2 1 should be done at least once every 12 months however it may be necessary to lubricate more often Diagram 5 10 depending on use Whenever the Table sta
11. llow Drill Bit T EBM2 0111A Pressure Foot Assembly 8 3S 14 Table Scale e EZ 1010L Table Release Handle Left EZ 1010R Table Release Handle Right 11 EBM 44A Channel Guard 12 EBM 20A Table Height Adjustment Assembly 13 EZ 1034 Table Guide EZ 107A Pattern Bar Housing Assembly 15 EZ 1014A Pattern Bar Stop Assembly 16 EZ 2004 Rail 47 EBM2 110A Chip Chute Assembly EBM2 1047 Chip Bag Bracket 19 FM5 5008 Power Cord 20 FM4 4003 Side Iron 21 EBM2 1034 Drill Strip 22 EZ 1033 Table 23 EZ 1025 Base Wire Harness 25 FM5 5002 1 4 HP Motor 26 EBM2 1000 Lift Pin 7 EZ 2001 Roller EBM2 111A Housing Assembly 29 EBM2 1019 Pivot Hub EBM2 103A Pivot Arm Set Assembly 31 EZ 1026 Lift Bars G EZ 1023 Lift Pin Housing 83 EZ 1024 Fork 84 EZ 1000 Fork Plate 85 EBM 82 6 Amp Fuse Page 15
12. njury to persons NEVER STAND ON MACHINE Serious injury could occur if the machine is tipped DON T OVERREACH Keep proper footing and balance at all times CHECK DAMAGED PARTS Before further use of the ma chine a guard or other part that is damaged should be care fully checked to determine that it will operate properly and perform its intended function check for alignment of moving parts binding of moving parts breakage of parts mount ing and any other conditions that may affect its operation A guard or other part that is damaged should be properly repair or replaced NEVER LEAVE MACHINE RUNNING UNATTENDED TURN POWER OFF Don t leave machine until it comes to a complete stop Page 02 2 Safety 2 2 Warning Labels e WARNING DO NOT EXPOSE TO RAIN OR USE IN DAMP LOCATIONS AWARNING Read and understand operator s manual and all other safety instructions before using this equipment WARNING FOR INDUSTRIAL AND IN PLANT USE ONLY AWARNING Entaglement hazard Rotating parts Do NOT operate with exposed long hair jewelry or loose clothing AWARNING Risk of eye injury Wear eye protection AWARNING Risk of Injury Do NOT operate without guards in place AWARNING Drill bits may be hot after use Allow drill bits to cool down before touching Severe shock hazard Only authorized personnel may service this equipment Turn power OFF before ent
13. ot position the Backgauge too close to the hollow drill bit so that it touches This can cause serious damage to the hollow drill bit causing it to break or shatter The Backgauge must be at least 1 8 from the circumference of the hollow drill bit 3 4 Installing the Paper Side Stops 3 4 1 Attach the Paper Side Stops FM4 4006 using two 2 Side Stop Diagram 3 80 Screws FM4 4007 each Position the Paper Side Stop as de sired and tighten down with light pressure Page 06 3 Setting Up Your Machine 3 5 Installing the Chip Bag 3 5 1 Attach the chip bag as shown by stretching the open end over the Diagram 3 90 top hook of the chip chute Continue fitting it around the entire edge of the chip chute making sure it is snug 3 5 2 Be sure to empty the chip bag regularly as needed Failure to empty the chip bag can result in clogging of the chip chute 3 6 Choosing and Installing the Pattern Bar 3 6 1 Your EBM 2 1 comes with five pattern bars included four 4 common patterns as shown in diagram 3 100 Choose the pat tern bar that lines up with your desired pattern Diagram 3 100 3 holes 2 3 4 apart center to center 3 holes 3 1 2 apart center to center 2 holes 2 3 4 apart center to center 3 holes 4 1 4 apart center to center standard three ring binder 3 6 2 Insert a Pattern Bar by loosening the Pattern Bar Stop EZ 1022 Diagram 3 110 and inserting the des
14. rts becoming difficult to lift it may be time to lubricate 5 2 2 Insert an oil can not provided into the hole on the rear panel just below the Chip Chute This hole provides direct access to the lift pin Lubricate the lift pin with a light machine oil Lift Pin Lubrication lt N Access Hole Page 11 6 Trouble Shooting Guide 6 1 Determining the Cause and Correction to Certain Problems Problem Cause Correction Drill bit not concentric Foreign material in chuck or in drill plug Inspect and clean Drill bit is bent Replace drill bit Drill bit not seated in chuck properly Reinsert drill bit correctly Chuck is not tight to spindle Tighten set screw Drill bit not drilling Drill bit plugged Remove and clear chips Check for other foreign matter Drill bit dull Sharpen drill bit Note In extreme conditions the drill chuck and or chip chute may be plugged Remove the drill bit loosen the chip chute pull down and clean See Operating Instructions Table lift system lifts unevenly or is noisy Ball bushings in lift system dry or worn Lubricate or replace Lift pin damaged Replace lift pin Machine vibrates wobbles resonates etc Drive motor loose
15. ry e AVERTISSEMENT NE PAS EXPOSER LA PLUIE ET NE PAS UTILISER DANS LES EMPLACEMENTS HUMIDES AVERTISSEMENT Lire et bien comprende le manuel de l op rateur avant d utiliser cette machine Le fait de ne pas suivre les consignes d utilisation peut entra ner des blessures graves ou endommager l quipement AVERTISSEMENT POUR UTILISATION INDUSTRIELLE ET EN USINE SEULEMENT AVERTISSEMENT Risque d enchev trement Pi ces rotatives Ne portez jamais de v tements amples ou de bijoux et attachez vous les cheveux lorsque vous op rez cette machine AVERTISSEMENT Risque de blessures aux yeux Protection des yeux n cessaire AVERTISSEMENT Faire attention de ne pas se blesser Ne pas utiliser cette machine sans la presence de tous les dispositifs de s curit AVERTISSEMENT Les outils de forage peuvent chauffer l usage Laisser refroidir les outils de forage avant de les toucher A Grave risqu d lectrocution Seul le personnel autoris peut faire l entretien de cet quipement COUPEZ l alimentation lectrique avant d entrer Page 03 2 3 Grounding Instructions Diagram 2 10 e DD METAL SCREW ua COVER OF GROUNDED OUTLET BOX GROUNDING PIN In the event of a malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This tool is equipped w
16. s when operating PLEASE NOTE THAT THE DRILL BITS MAY BE HOT AFTER USE PRO CEDE WITH CAUTION WHEN CHANGING THE DRILL BITS DON T USE IN DANGEROUS ENVIRONMENT Don t use this machine in damp or wet locations or expose it to rain Keep work area well lighted THIS MACHINE IS DESIGNED FOR ONE PERSON OP ERATION Never operate the machine with more than one person KEEP CHILDREN AWAY All visitors should be kept a safe distance from the work area MAKE WORKSHOP KID PROOF with padlocks or master switches DON T FORCE MACHINE It will do the job better and safer at the rate for which it was designed USE RIGHT MACHINE Don t force tool or attachment to do a job for which it was not designed MAINTAIN MACHINE WITH CARE Keep tools sharp and clean for best and safest performance Follow instructions for lubricating and changing accessories REMOVE ADJUSTING KEYS AND WRENCHES Form habit of checking to see that keys and adjusting wrenches are removed from machine before turning it on KEEP WORK AREA CLEAN Cluttered areas and benches invite accidents DISCONNECT MACHINE before servicing when changing accessories such as drill bits drill blocks and the like REDUCE THE RISK OF UNINTENTIONAL STARTING Make sure the power switch is in the off position before plugging in USE RECOMMENDED ACCESSORIES Consult the us er s manual for recommended accessories The use of im proper accessories may cause risk of i
17. ust read and understand the Users Manual including all safety instructions before using this equipment Failure to fully understand the safety instructions can result in personal injury If after reading the manual you are still uncertain about use please contact the dealer from whom you purchased the machine for assistance If you need contact information for a Service Technician nearest you please call 585 436 1934 SAFETY OF THIS EQUIPMENT IS THE RESPONSIBILITY OF THE USER S Please read and follow all warning labels on your machine INDUSTRIAL AND IN PLANT USE ONLY This equipment is for use in industrial and in plant areas only and must be operated by trained and qualified personnel WEAR PROPER APPAREL Do not wear loose clothing gloves neckties rings bracelets or other jewelry which may get caught in moving parts Non slip footwear is recommended Wear protective hair covering to contain long hair Keep hands clear while operating machine ALWAYS USE SAFETY GLASSES Also use face or dust mask if drilling operation is dusty Everyday eyeglasses only have impact resistant lenses they are NOT safety glasses KEEP GUARDS IN PLACE and in working order Always disconnect the power before servicing this machine Service should only be performed by a QUALIFIED TECH NICIAN Always turn the machine to off mode and wait for the drills to stop spinning before installing or removing drill bits Keep hands away from drill
Download Pdf Manuals
Related Search