FX3U-USB-BD USER`S MANUAL
Contents
1. Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Click Next gt The installation of the USB Serial Port software will begin If using Windows 2000 a screen to select the location of the installation files is displayed Please select the CD ROM drive 5 The screen of 2 is displayed Only in Windows XP Click Continue Anyway 6 The following screen is displayed Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for F FX USB A W FX3LU USB BD Click Finish to close the wizard Click Finish The installation of the USB Serial Port software will finish The CD ROM USB driver software can be removed from the personal computer at this time 7 Installation Confirmation of Driver Procedure for confirming the installation of the driver is described below Windows XP example follows e In Windows XP click Start Control Panel System gt Hardware gt Device Manager D and the window below will be displayed Please confirm the COM number to which the driver is allocated COM and LPT e If using Windows 98 Windows 98SE Windows Millennium Edition or Windows 2000 A screen that is equivalent to the one below is displayed by clicking My Computer Control Panel gt System gt Device Manager in2. disconnect the USB cable once from either the personal computer or the FX3U USB BD and connect it again Then clear the error message and choose Write Read or Monitor again e The programming tool may not be operated properly due to a contact failure at connectors or wire breakage Make sure to save the program before transferring or changing it 10 Troubleshooting If communication cannot be established between the PLC and a personal computer using FX3U USB BD confirm the following status by checking SD LED and RD LED in FX3U USB BD The status of SD LED and RD RED The status of SD LED and RD LED Blinking Communicating correctly e Confirm that the power is supplied to the personal computer SD e Confirm the personal computer and the PLC are Extinguished connected properly with the specified cable e Confirm that the communication settings and connected PLC are correctly set in the software Refer to the software manual RD Blinking Data receiving e Confirm that the power is supplied to PLC e The PLC will not operate when a configuration that exceeds the DC 5V or DC 24V capacity is used It will also be impossible to communicate normally Extinguished e Confirm that the specified cable is used to connect the personal computer and PLC e Confirm that the communication settings and connected PLC are correctly set in the software Refer to the software manual This manual confers no industrial property rights or
3. disconnect the USB cable once from either the personal computer or the FX3U USB BD and connect it again Then clear the error message and choose Write Read or Monitor again e The programming tool may not be operated properly due to a contact failure at connectors or wire breakage Make sure to save the program before transferring or changing it 10 Troubleshooting If communication cannot be established between the PLC and a personal computer using FX3U USB BD confirm the following status by checking SD LED and RD LED in FX3u USB BD The status of SD LED and RD RED The status of SD Contents LED and RD LED Communicating correctly e Confirm that the power is supplied to the personal computer SD e Confirm the personal computer and the PLC are Extinguished connected properly with the specified cable e Confirm that the communication settings and connected PLC are correctly set in the software Refer to the software manual Data receiving e Confirm that the power is supplied to PLC e The PLC will not operate when a configuration that exceeds the DC 5V or DC 24V capacity is used RD It will also be impossible to communicate normally Extinguished e Confirm that the specified cable is used to connect the personal computer and PLC e Confirm that the communication settings and This manual confers no industrial property rights or any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation ca
4. 57600 115200 bps Port USB MINI B plug female 3 5 System Requirements Item Specification Microsoft Windows 98 Windows 98SE os Microsoft Windows Millennium Edition Windows Me Microsoft Windows 2000 Microsoft Windows XP Software SWLID5C GPPW E GX Developer FX PCS WIN E 1 GX Developer Ver 8 23Z or later is applicable to the FX3U Series PLC Its Ver 8 13P or later is applicable to FX3UC Series PLC For further details concerning alternative inapplicable programming tool setting refer to the following manual Refer to FX3U Series User s Manual Hardware Edition 4 System Configuration Connected equipment and connected cable PLC FX3U USB BD E Personal computer USB driver software Install areas USB cable for personal computer connection included with the product USB port For details of the programming communication refer to the following manual Refer to FX Series User s Manual Data Communication Edition 5 Connecting Procedure 1 Power off the PLC 2 Connect the USB MINI B plug male connector of the USB cable to the FX3U USB BD 3 Connect the USB A plug male connector of the USB cable to the personal computer 4 Turn ON the power supply of the PLC 5 Turn ON the power supply of the personal computer 6 Driver Installation Procedure for installing the driver is explained below Windows XP
5. any rights of any other kind nor does it confer any patent licenses Mitsubishi Electric Corporation cannot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual Contents Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system aa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE MITSUBISHI DENKI BLDG MARUNOUTI TOKYO 100 8310 HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN JY997D13501B E sAPANESE SE ENGLISH a MITSUBISHI PROGRAMMABLE
6. installation follows e Windows 98 Windows 98SE Windows Millennium Edition and Windows 2000 the installation method will vary Installation of the driver is canceled during the following process the installation is not carried out correctly If the installation is canceled uninstall the driver and install again Please refer to Chapter 8 for instructions on uninstalling the driver Please install the driver with the following procedure 1 When the USB cable is connected to the personal computer the following screen is displayed When the USB cable is connected to the personal computer the following screen is displayed Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for FX3U USB BD If your hardware came with an installation CD lt gt or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Insert the included CD ROM into the personal computer s CD ROM drive Click Next gt The installation of the USB driver software will begin If using Windows 98 Windows 98SE Windows Millennium Edition and Windows 2000 A window to select the location of the installation files Please select the CD ROM drive 2 The following screen is displayed Only in Windows XP Hardware Installati
7. it to the expansion board connector 5 Fix the expansion board right fig B to the main unit using the M3 tapping screws of the provided right fig D Tighten to a torque 0 3 to 0 6 N m 3 Specification 3 1 Applicable PLC Model name FX3U Series PLC Applicability Ver 2 00 or later from the first product Ver 1 00 or later FX3UC Series PLC Only one function expansion board can be used for one main unit Two or more FX3U USB BD cannot be used or other expansion boards such as FX3u 422 BD or FX3U 485 BD cannot be installed used together with FX3U USB BD For details of the system configuration refer to the following manual Refer to FX Series User s Manual Data Communication Edition 3 2 General Specifications General specifications are equivalent to the PLC main unit For general specifications refer to the following manual However please don t perform any dielectric withstand voltage test and insulation resistance test to this product Refer to FX3U Series User s Manual Hardware Edition 3 3 Power Supply Specification Item Specification 15mA DC 5V supplied by DC 5V power of main unit 30mA DC 5V supplied by USB connector of personal computer Current consumption 3 4 Communication Specifications Item Specification Transmission USB2 0 For full speed standard Isolation Photocoupler isolation Between communication line and CPU Maximum 5m 196 9 at most Included cable i
8. the menu of the personal computer Device Manager view Help s amp R zR PC 728 1 Computer S Disk drives Display adapters 4 DYD CD ROM drives 4 Floppy disk controllers J2 Floppy disk drives E IDE ATA ATAPI controllers 5 gt Keyboards Mice and other pointing devices Monitors ES Network adapters aF Ports COM amp LPT B BD COM Communications Port COM1 F Communications Port COM2 a ECP Printer Port LPT1 F FX USB AWJFX3U USB BD COM SB Processors amp SCSI and RAID controllers Sound video and game controllers System devices Universal Serial Bus controllers a cin A File Action Te Intel r 8280144 USB Universal Host Controller USB Root Hub Check following FX USB AW FX3U USB BD is indicated at A FX USB AW FX3U USB BD COM is indicated at B indicates the COM number used in FX3U USB BD Install the driver again when is displayed Select the programming software COM number as the COM number currently assigned on the screen above Setting GX Developer Double click Online gt Transfer setup gt Serial of personal computer side I F Select the same COM number as the COM number of the personal computer when the personal computer side I F serial setting Dialog Box appears Click OK of Connection Setup screen to end Transfer Setup PC side I F 8 Method for Uninstalling Driver The procedure for uninstalling the driv
9. CONTROLLERS MELSEGIF FX3U USB BD Side Changes for the Better USER S MANUAL Manual Number JY997D13501 on eooo This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective June 2005 Specifications are subject to change without notice 2005 Mitsubishi Electric Corporation F X 3u Safety Precaution Read these precautions before use This manual classify the safety precautions into two categories DANGER and ZACAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the directions for usage Associated Manuals Manual name Descr
10. JY997D13501B E sAPANESE SE ENGLISH a MITSUBISHI PROGRAMMABLE CONTROLLERS MELSEGIF FX3U USB BD Side Changes for the Better USER S MANUAL Manual Number JY997D13501 n ooo This manual describes the part names dimensions mounting and specifications of the product Before use read this manual and manuals of relevant products fully to acquire proficiency in handling and operating the product Make sure to learn all the product information safety information and precautions And store this manual in a safe place so that you can take it out and read it whenever necessary Always forward it to the end user Registration The company name and the product name to be described in this manual are the registered trademarks or trademarks of each company Effective June 2005 Specifications are subject to change without notice 2005 Mitsubishi Electric Corporation F X 3u Safety Precaution Read these precautions before use This manual classify the safety precautions into two categories DANGER and ZACAUTION Indicates that incorrect handling may cause hazardous lt gt DANGER conditions resulting in death or severe injury Indicates that incorrect handling may cause hazardous CAUTION conditions resulting in medium or slight personal injury or physical damage Depending on circumstances procedures indicated by CAUTION may also be linked to serious results In any case it is important to follow the d
11. alling for this hardware FX USB AW FX3U USB BD has not passed Windows Logo testing to verify its compatibility with Windows XP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Click Continue Anyway 3 The following screen is displayed Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for a FX USB AW FX3U USB BD Click Finish to close the wizard Click Finish The installation of the USB driver software will finish If Windows 98 Windows 98SE or Windows Millennium Edition is used installation of the USB Serial Port software begins and ends automatically The CD ROM can be removed from the personal computer at this time If using Windows 2000 or Windows XP proceed to step 4 4 The following screen is displayed Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for USB Serial Port If your hardware came with an installation CD lt 6 or floppy disk insert it now What do you want the wizard to do Install the softw
12. ard right fig B to the main unit using the M3 tapping screws of the provided right fig D Tighten to a torque 0 3 to 0 6 N m 3 Specification 3 1 Applicable PLC Model name FX3U Series PLC Applicability Ver 2 00 or later from the first product Ver 1 00 or later FX3UC Series PLC Only one function expansion board can be used for one main unit Two or more FX3U USB BD cannot be used or other expansion boards such as FX3U 422 BD or FX3U 485 BD cannot be installed used together with FX3U USB BD For details of the system configuration refer to the following manual Refer to FX Series User s Manual Data Communication Edition 3 2 General Specifications General specifications are equivalent to the PLC main unit For general specifications refer to the following manual However please don t perform any dielectric withstand voltage test and insulation resistance test to this product Refer to FX3U Series User s Manual Hardware Edition 3 3 Power Supply Specification Item Specification 15mA DC 5V supplied by DC 5V power of main unit 30mA DC 5V supplied by USB connector of personal computer Current consumption 3 4 Communication Specifications Item Specification Transmission USB2 0 For full speed standard Isolation Photocoupler isolation Between communication line and CPU ex mums 3 5m 196 9 at most Included cable is 3m 118 1 transmission distance Baud Rate 9600 19200 38400
13. are automatically Recommended Install from a list or specific location Advanced Click Next to continue Click Next gt The installation of the USB Serial Port software will begin If using Windows 2000 a screen to select the location of the installation files is displayed Please select the CD ROM drive 5 The screen of 2 is displayed Only in Windows XP Click Continue Anyway 6 The following screen is displayed Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for Jy FX USB A W FX3LU USB BD Click Finish to close the wizard Click Finish The installation of the USB Serial Port software will finish The CD ROM USB driver software can be removed from the personal computer at this time 7 Installation Confirmation of Driver Procedure for confirming the installation of the driver is described below Windows XP example follows e In Windows XP click Start Control Panel System gt Hardware gt Device Manager D and the window below will be displayed Please confirm the COM number to which the driver is allocated COM and LPT e If using Windows 98 Windows 98SE Windows Millennium Edition or Windows 2000 A screen that is equivalent to the one below is displayed by clicking My Computer Control Panel System gt Device Manager in the menu of the personal
14. ation may be caused Use screwdrivers carefully when performing installation work thus avoiding accident or product damage When drilling screw holes or wiring cutting chips or wire chips should not enter ventilation slits Such an accident may cause fire failure or malfunction Do not touch the conductive parts of the product directly thus avoiding failure or malfunction Fix the expansion board securely to the specified connector Incorrect connection may cause malfunction A The following explains the installation method to FX3U FX3UC Series PLC FX3U Series PLC is used for the following example For removing and installing details refer to the PLC main unit manual However FX3UC Series PLC manual is only available in Japanese Refer to FX3U Series User s Manual Hardware Edition 2 1 Installation Method e Refer to the procedure 2 for configuring a new system e Refer to the procedure 1 for adding product to an existing system 1 Power off the PLC Disconnect all the cables connected to the PLC Dismount the PLC from the DIN rail 2 Using a flat blade screwdriver as shown in the right figure lift the little dummy expansion board cover right fig A Do not damage the circuit board or electronic parts 3 Remove the dummy expansion board cover right fig A in a parallel motion away from the main unit 4 Make sure the expansion board right fig B is in parallel with the main unit right fig C and fix
15. change is performed please read all relevant manuals and confirm safety aspects Incorrect operation may damage the product or cause an accident STARTUP AND MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the unit Doing so may cause failure malfunction or fire For repair contact your local Mitsubishi Electric distributor e Do not drop the product or do not exert strong impact doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a company certified in the disposal of electronic waste for environmentally safe recycling and disposal of the product TRANSPORT AND STORAGE PRECAUTIONS CAUTION e During transportation avoid any impact as the product is a precision instrument Check the operation of the product after transportation e Only one function extension board can be installed in the main unit other function extension boards such as FX3U 422 BD or FX3U 485 BD cannot be installed nor used when the FX3U USB BD is installed e FX3U USB BD and a personal computer are connected and the PLC is turned on and then an operations such as write read and monitor are tried for the first time using a programming tool a communication error message may be displayed In such a case clear the message and try the operations again e If a communication error message is indicated while operating the programming tool when executing Write to PLC Read from PLC or Monitor
16. computer Device Manager File Action View Help amp zR PC 728 Computer amp Disk drives Display adapters 2 DYDICD ROM drives Floppy disk controllers J Floppy disk drives Sy IDE ATAJATAPI controllers 5 gt Keyboards Mice and other pointing devices Monitors ES Network adapters UY Ports COM amp LPT B BD COM 1 0 0 0 A Communications Port COM1 Communications Port COM2 F ECP Printer Port LPT1 YA FX UISB AW FX3U LISB BD COM ae Processors amp SCSI and RAID controllers Sound video and game controllers System devices Universal Serial Bus controllers Intel r 8280144 USB Universal Host Controller USB Root Hub a min A Check following FX USB AW FX3U USB BD is indicated at A FX USB AW FX3U USB BD COM is indicated at B indicates the COM number used in FX3U USB BD Install the driver again when is displayed Select the programming software COM number as the COM number currently assigned on the screen above Setting GX Developer Double click Online Transfer setup gt Serial of personal computer side I F Select the same COM number as the COM number of the personal computer when the personal computer side I F serial setting Dialog Box appears Click OK of Connection Setup screen to end Transfer Setup PC side F 8 Method for Uninstalling Driver The procedure for uninstalling the driver is ex
17. dows 98 Windows 98SE Windows Millennium Edition and Windows 2000 the installation method will vary Installation of the driver is canceled during the following process the installation is not carried out correctly If the installation is canceled uninstall the driver and install again Please refer to Chapter 8 for instructions on uninstalling the driver Please install the driver with the following procedure 1 When the USB cable is connected to the personal computer the following screen is displayed When the USB cable is connected to the personal computer the following screen is displayed Found New Hardware Wizard Welcome to the Found New Hardware Wizard This wizard helps you install software for FX3U USB BD If your hardware came with an installation CD lt lt or floppy disk insert it now What do you want the wizard to do Install the software automatically Recommended Install from a list or specific location Advanced Click Next to continue Insert the included CD ROM into the personal computer s CD ROM drive Click Next gt The installation of the USB driver software will begin If using Windows 98 Windows 98SE Windows Millennium Edition and Windows 2000 A window to select the location of the installation files Please select the CD ROM drive 2 The following screen is displayed Only in Windows XP Hardware Installation The software you are inst
18. e change is performed please read all relevant manuals and confirm safety aspects Incorrect operation may damage the product or cause an accident STARTUP AND MAINTENANCE PRECAUTIONS CAUTION e Do not disassemble or modify the unit Doing so may cause failure malfunction or fire For repair contact your local Mitsubishi Electric distributor e Do not drop the product or do not exert strong impact doing so may cause damage DISPOSAL PRECAUTIONS CAUTION e Please contact a company certified in the disposal of electronic waste for environmentally safe recycling and disposal of the product TRANSPORT AND STORAGE PRECAUTIONS CAUTION e During transportation avoid any impact as the product is a precision instrument Check the operation of the product after transportation e Only one function extension board can be installed in the main unit other function extension boards such as FX3U 422 BD or FX3U 485 BD cannot be installed nor used when the FX3U USB BD is installed e FX3U USB BD and a personal computer are connected and the PLC is turned on and then an operations such as write read and monitor are tried for the first time using a programming tool a communication error message may be displayed In such a case clear the message and try the operations again e If a communication error message is indicated while operating the programming tool when executing Write to PLC Read from PLC or Monitor
19. ems USB driver software CD ROM USB cable 3m 118 1 User s Manual this manual 1 2 External Dimensions and Part Names 53 5 2 11 0 77 Special adapter connector MASS Weight 20g 0 05Ibs cover is removed USB cable included with the product 9 1 Mounting holes 2 3 2 2 RD LED Lighting while receiving data LED color red 3 SD LED Lighting while sending data LED color red 4 USB Connector 5 Main unit connector 6 Special adapter connector cover 7 Special adapter connector 8 USB Connector To FX3U USB BD MINI B plug male 9 USB Connector To personal computer MINI B plug female A plug male 2 Installation INSTALLATION PRECAUTIONS DANGER e Cut off all phases of the power source externally before starting the installation or wiring work thus avoiding electric shock or damages to the product INSTALLATION PRECAUTIONS CAUTION e Use the product in the environment within the general specifications described in PLC main unit manual Hardware Edition Never use the product in areas with dust oily smoke conductive dusts corrosive gas salt air Cle H2S NH3 SO2 or NO2 flammable gas vibrations or impacts or expose it to high temperature condensation or wind and rain If the product is used in such a place described above electrical shock fire malfunction damage or deterioration may be caused Use screwdrivers carefully when per
20. er is explained below A Windows XP example follows Please uninstall the driver by the procedure below 1 Detach the USB cable from the personal computer Click Start Control Panel Add or Remove Programs in the menu of the personal computer the window below will be displayed In case of Windows Me of Windows 98 and Windows 98SE Windows 2000 A screen that is equivalent to the one below is displayed by clicking My Computer gt Control Panel Add Remove Programs in the menu of the personal computer Add or Remove Programs hl Currently installed programs Sort by Name v Change or Remove Programs fe FX USB AW FX3U USB BD Drivers To change this program or remove it from your computer click Change Remove Change Remove Add New Programs Add Remove Windows Components Click Change Remove 2 The following screen is displayed FTDI Uninstaller Version 2 1 If your USB device is connected please unplug it now Press Continue to uninstall the drivers or Cancel to quit Continue Click Continue 3 The following screen is displayed FTDI Uninstaller Version 2 1 Uninstalling VID_O6D3 amp PID_0284 Deleting registry entries Deleting files Uninstall complete press Finish to exit ees Click Finish 9 Caution on use STARTUP AND MAINTENANCE PRECAUTIONS DANGER e Before a program or setting on line or off lin
21. expansion board FX3U USB BD M3 tapping screws Included items USB driver software CD ROM USB cable 3m 118 1 User s Manual this manual 1 2 External Dimensions and Part Names 53 5 2 11 Special adapter connector cover is removed MASS Weight 20g 0 05lbs USB cable included with the product 9 1 Mounting holes 2 03 2 2 RD LED Lighting while receiving data LED color red 3 SD LED Lighting while sending data LED color red 4 USB Connector 5 Main unit connector 6 Special adapter connector cover 7 Special adapter connector 8 USB Connector To FX3U USB BD MINI B plug male 9 USB Connector To personal computer MINI B plug female A plug male 2 Installation INSTALLATION PRECAUTIONS DANGER e Cut off all phases of the power source externally before starting the installation or wiring work thus avoiding electric shock or damages to the product INSTALLATION PRECAUTIONS CAUTION e Use the product in the environment within the general specifications described in PLC main unit manual Hardware Edition Never use the product in areas with dust oily smoke conductive dusts corrosive gas salt air Cle H2S NH3 SO2 or NO2 flammable gas vibrations or impacts or expose it to high temperature condensation or wind and rain If the product is used in such a place described above electrical shock fire malfunction damage or deterior
22. forming installation work thus avoiding accident or product damage When drilling screw holes or wiring cutting chips or wire chips should not enter ventilation slits Such an accident may cause fire failure or malfunction Do not touch the conductive parts of the product directly thus avoiding failure or malfunction Fix the expansion board securely to the specified connector Incorrect connection may cause malfunction A The following explains the installation method to FX3U FX3UC Series PLC FX3U Series PLC is used for the following example For removing and installing details refer to the PLC main unit manual However FX3UC Series PLC manual is only available in Japanese Refer to FX3U Series User s Manual Hardware Edition 2 1 Installation Method e Refer to the procedure 2 for configuring a new system e Refer to the procedure 1 for adding product to an existing system 1 Power off the PLC Disconnect all the cables connected to the PLC Dismount the PLC from the DIN rail 2 Using a flat blade screwdriver as shown in the right figure lift the little dummy expansion board cover right fig A Do not damage the circuit board or electronic parts 3 Remove the dummy expansion board cover right fig A in a parallel motion away from the main unit 4 Make sure the expansion board right fig B is in parallel with the main unit right fig C and fix it to the expansion board connector 5 Fix the expansion bo
23. iption Explains FX3U Series PLC specification details for I O wiring installation and maintenance JY997D16501 MODEL CODE 09R516 FX3U Series User s Manual Hardware Edition FX Series User s Manual Data Communication Edition Explains N N link parallel link computer link no protocol communication by RS instructions FX2N 232 IF JY997D16901 MODEL CODE 09R715 Note FX3UC Series PLC specification details for I O wiring installation and maintenance can only be found in the Japanese Manual How to obtain manuals For the necessary product manuals or documents consult with the Mitsubishi Electric dealer from where you purchase your product Applicable standard FX3U USB BD made in June 2005 or later complies with EC directive EMC Directive Further information can be found in the following manual However FX3UC 32 MT LT does not comply with EC directive EMC Directive Refer to FX3U Series Hardware Manual Manual No JY997D18801 1 Outline The FX3U USB BD board hereinafter called USB BD is a function extension board for USB communication equipped with an USB port MINI B plug female By connecting the USB BD and a personal computer program transfer to a PLC main unit and monitoring can be performed 1 1 Incorporated Items Check if the following product and items are included in the package USB communication expansion board FX3U USB BD M3 tapping screws Product Included it
24. irections for usage Associated Manuals Manual name Description Explains FX3U Series PLC specification details for I O wiring installation and maintenance JY997D16501 MODEL CODE 09R516 FX3U Series User s Manual Hardware Edition FX Series User s Manual Data Communication Edition Explains N N link parallel link computer link no protocol communication by RS instructions FX2N 232 IF JY997D16901 MODEL CODE 09R715 Note FX3UC Series PLC specification details for I O wiring installation and maintenance can only be found in the Japanese Manual How to obtain manuals For the necessary product manuals or documents consult with the Mitsubishi Electric dealer from where you purchase your product Applicable standard FX3U USB BD made in June 2005 or later complies with EC directive EMC Directive Further information can be found in the following manual However FX3UC 32 MT LT does not comply with EC directive EMC Directive Refer to FX3U Series Hardware Manual Manual No JY997D18801 1 Outline The FX3U USB BD board hereinafter called USB BD is a function extension board for USB communication equipped with an USB port MINI B plug female By connecting the USB BD and a personal computer program transfer to a PLC main unit and monitoring can be performed 1 1 Incorporated Items Check if the following product and items are included in the package Product USB communication
25. nnot be held responsible for any problems involving industrial property rights which may occur as a result of using the contents noted in this manual connected PLC are correctly set in the software Refer to the software manual Warranty Mitsubishi will not be held liable for damage caused by factors found not to be the cause of Mitsubishi machine damage or lost profits caused by faults in the Mitsubishi products damage secondary damage accident compensation caused by special factors unpredictable by Mitsubishi damages to products other than Mitsubishi products and to other duties e This product has been manufactured as a general purpose part for general industries and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life e Before using the product for special purposes such as nuclear power electric power aerospace medicine or passenger movement vehicles consult with Mitsubishi Electric e This product has been manufactured under strict quality control However when installing the product where major accidents or losses could occur if the product fails install appropriate backup or failsafe functions in the system afa MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE MITSUBISHI DENKI BLDG MARUNOUTI TOKYO 100 8310 HIMEJI WORKS 840 CHIYODA CHO HIMEJI JAPAN
26. on dd The software you are installing for this hardware FX USB AW FX3U USB BD has not passed Windows Logo testing to verify its compatibility with Windows XP Tell me why this testing is important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing Continue Anyway STOP Installation Click Continue Anyway 3 The following screen is displayed Found New Hardware Wizard Completing the Found New Hardware Wizard The wizard has finished installing the software for 2 FX USB AW FX3U USB BD Click Finish to close the wizard Click Finish The installation of the USB driver software will finish If Windows 98 Windows 98SE or Windows Millennium Edition is used installation of the USB Serial Port software begins and ends automatically The CD ROM can be removed from the personal computer at this time If using Windows 2000 or Windows XP proceed to step 4 4 The following screen is displayed Welcome to the Found New Hardware Wizard Found New Hardware Wizard This wizard helps you install software for USB Serial Port If your hardware came with an installation CD lt or floppy disk insert it now What do you want the wizard to do
27. plained below A Windows XP example follows Please uninstall the driver by the procedure below 1 Detach the USB cable from the personal computer Click Start Control Panel Add or Remove Programs in the menu of the personal computer the window below will be displayed In case of Windows Me of Windows 98 and Windows 98SE Windows 2000 A screen that is equivalent to the one below is displayed by clicking My Computer gt Control Panel gt Add Remove Programs in the menu of the personal computer Add or Remove Programs Sort by Name v hil Currently installed programs Change or fe FX USB AW FX3U USB BD Drivers Remove Programs k To change this program or remove it from your computer click Change Remove Change Remove Add New Programs Add Remove Windows Components Click Change Remove 2 The following screen is displayed FTDI Uninstaller Version 2 1 If your USB device is connected please unplug it now Press Continue to uninstall the drivers or Cancel to quit Continue Click Continue 3 The following screen is displayed FTDI Uninstaller Version 2 1 Uninstalling VID_O6D3 amp PID_0284 Deleting registry entries Deleting files Uninstall complete press Finish to exit ais Click Finish 9 Caution on use STARTUP AND MAINTENANCE PRECAUTIONS DANGER e Before a program or setting on line or off line
28. s 3m 118 1 transmission distance Baud Rate 9600 1 9200 38400 57600 1 15200 bps Port USB MINI B plug female 3 5 System Requirements Item Specification Microsoft Windows 98 Windows 98SE os Microsoft Windows Millennium Edition Windows Me Microsoft Windows 2000 Microsoft Windows XP Software SWLID5C GPPW E GX Developer FX PCS WIN E 1 GX Developer Ver 8 23Z or later is applicable to the FX3U Series PLC Its Ver 8 13P or later is applicable to FX3UC Series PLC For further details concerning alternative inapplicable programming tool setting refer to the following manual Refer to FX3U Series User s Manual Hardware Edition 4 System Configuration Connected equipment and connected cable PLC FX3U USB BD Personal computer USB driver software E Install USB port For details of the programming communication refer to the following manual Refer to FX Series User s Manual Data Communication Edition 5 Connecting Procedure 1 Power off the PLC 2 Connect the USB MINI B plug male connector of the USB cable to the FX3U USB BD 3 Connect the USB A plug male connector of the USB cable to the personal computer 4 Turn ON the power supply of the PLC 5 Turn ON the power supply of the personal computer 6 Driver Installation Procedure for installing the driver is explained below Windows XP installation follows e Win
Download Pdf Manuals
Related Search