EVMB-‐ICNR Quick experience guide
Contents
1. Connected to me Flash Search for AP DCS on Line RF_LED ON Connected to AP Off Not connected to DCS Offline Jumper must be connected To allow EVMB ICNR to be i 5 Initially powered as Evaluated Pocs Access Point D3 Rdyns Module Daughter D8 Plocs amp Board D6 D Rdy SW5 O pioc3 D9 USB DEVICE Rdyns D Rdy my DTR on RS232 P wn ie I N m N N ISOH 9SN2. By default PIOC3 PIOCS are set to input Changing the PIOC direction will require a reset to EVMB ICNR in order for the change to be effective The default is Disable A Controlling the state of PIOC in input mode a Input mode Press the button next to the PIOC on the EVMB ICNR and check the status of the LED image next to the PIOC on the EVMB ICNR host web site b Press on the led image next to the PIOC on the EVMB ICNR host web site to reset the state of the input and check the changes B Changing the PIOC direction Use the direction selectors to change the PIOC direction After changing direction the EVMB ICNR will reset itself and the change will be shown on the EVMB ICNR host website after 20 sec An on off icon will be shown next to the PIOC that is set as an output C Controlling the state of PIOC in output mode Press the on off icon and check status of the LED next to PIOC on the EVMB D Reading position of potentiometer Rotate potentiometer Analog input P1 and check position on the EVMB ICNR host web site Resetting the EVMB ICNR A Resetting to factory default Press the MSEL button SW2 for 30 sec B Changing the back to access point operation mode Using the remote access through the DCS delete the SSID parameter form the HOST web site and power reset the EVMB ICNR EVMB ICNR layout Please refer to the EVMB user manual for further detailed information about the board functionalities Analog On
3. Quick experience guide Dear Customer Thanks for choosing ConnectOne for your loT experience The EVMB ICNR is an iChipNet Ready evaluation kit which will allow you to experience Connect One s iChipNet a complete loT end to end solution The WiFi module on the EVMB ICNR has been programmed with special host website specifically designed to allow you to control three Programmable Input Output Controls PIOCs and one Analog input that located on the EVMB ICNR board Using the internal host website you will be able to control the direction of the PIOC input or Output force changes on the EVMB ICNR board while in output state and receive status of the PIOC while in input state The purpose of this quick guide is to allow you to access the EVMB ICNR internal host website using Connect One s Device Connectivity Server DCS which is a device management application for remote access to devices in the field It is recommended that you be familiar with the basic EVMB User Manual located in Connect One s web site under the Products tab http www connectone com page_id 3764 The kit includes the following EVMB Evaluation Master Kit EVM iW SMG2SMT OB Evaluation WiFi Daughter Board for iW SMG2SMT OB with special host website Setup and usage instructions Please carefully follow the below instructions for the best iChipNet experience 1 Device Connectivity Server DCS account setup The DCS is the cloud server to which devi
4. ces are registered It allows remote access to a device for the purpose of control status and configuration A Browse to www ichipnet com managernew B Click Create Account and follow the instruction until complete C Wait for an activation email click on the link to access your new DCS account using the account name and password 2 iChipNet Ready Evaluation Board setup Using the supplied power supply hook up the EVMB ICNR to the power and turn it on The EVMM ICNR is set up as a WiFi Access Point by default A On your computers WiFi network connection list search for the ICNR S N Access Point The S N is an 8 digit number starts with 140 The S N label is located on the module B Once connected to the EVMB ICNR s n access point browse to 10 0 0 1 3 Setting up the EVMB ICNR for internet connection Using your local access point connection credential the EVMB ICNR will connect to the internet and register itself to the Device Connectivity Server DCS A Inthe WiFi Configuration section please enter the SSID of your local router the Security type and the Password Phrase B Inthe Device Connectivity Server section please enter the account name you created in section 1 above and give your EVMB ICNR a name C Click submit At this stage the unit will reset itself into client mode and will use your local access point for Internet connectivity The RF Led on the module will blink while searching for your local acce
5. ss point and will stay on when the access point detected and associated Upon connecting the EVMB ICNR will automatically register itself in the Device Connectivity Server DCS under the account name you have created in section 1 and will use the name you have set in section 3 B Rdyns LED on the EVMB ICNR will be on to indicate the module is connected to the DCS Remote device access Using the Device Connectivity Server for remote device access A Browse to www ichipnet com managernew B Enter your account name and password and click Log In The Device Connectivity Server will access your account and will show the registered device Clicking the icon under Host Site will access the EVMB ICNR internal web site You are now connected to your EVMB ICNR remotely through the internet and are able to access it from any place that has an internet connection EVMB ICNR Host Website Connect The Device Networking Authority a PIOC4 Input v WiFi Configuration PIOCS Input v SSID MySSID l PIOC3 Input v security type Open Y Pass Phrase Potentiometer Device Connectivity Server Identity Account name MyAccount PSN 14085011 Device name Device IP addr 192 168 2 106 MAC 000394105840 1 Activating the PIOC s On off EVMB ICNR Module Serial number lt lt EVMB ICNR IP Address EVMB ICNR Module MAC address The module s GPIO pins corresponds to the ones on the EVMB
Download Pdf Manuals
Related Search