file - Sirona - Technical Documentation
Contents
1. 65 26 060 D3534 D3534 208 06 02 02 06 2015 31 8 ACQUISITION phase Sirona Dental Systems GmbH 8 5 Performing a scan Operator s Manual CEREC Ortho SW 8 5 Performing a scan 8 5 1 Procedure for the guided scanning process Description For the CEREC Ortho SW Guided Scanning process the complete lower jaw complete upper jaw and the bite situation are scanned If only a single jaw is scanned the bite situation must not be recorded The Guided Scanning process guides the user through several partial scans whereby the single quadrants are scanned A complete model is then rendered from the partial scans Scan objects and the Step Menu The Guided Scanning process contains 3 scan objects A e Lower jaw scan e Upper jaw scan e Buccal registration The selected scan object is highlighted in yellow Every scan object contains several steps which are displayed in a Step Menu B The selected step is highlighted in yellow and marked with a red line When a step is finished a confirmation symbol is displayed The finished step is marked with a green line in the Step Menu and the software switches to the next step You can repeat the last step by clicking on the double arrow on the left side of the Step Menu In this case the current scan step is discarded and must be repeated 65 26 060 D3534 32 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH Operator s Manual CEREC Ortho SW 8 ACQUISITION phase2. ened 06 2015 Sirona The Dental Company CEREC Ortho SW Software Version 1 1 Operator s Manual Table of contents 1 MOGUCIM sersa E EENEN ST TAE 1 1 Dear o Pr e n LT 1 2 Copynght and trademark T ko OpenSource en U T TTT 2 General CAL T 2 1 CSU Gal E st L jaan auanimeloonatauca eum 2 2 General Safety information eee eee e e 29 SUCTUFE OT INE MANU Al TTT 2 3 1 Identification of danger levels sese 2 3 2 Formats and Symbols USE sea T A ZOO CONVCMUONS T 2 3 4 Formats ofthe manual sese eee 2 4 R 1 27 9 T vn 2 e TT Ziel Phas s TTT 2AA Descriptio T ZAAZ ACOUSITON TT S a Ee MODE rarene O a CANA EXPOR Feskineaona na ae Ganaiaeecenans Zee ViOOU WINES HT 24S Sep MENU TT ZAA SV 121 H eT S p Ny 11T n WINGOW soncni a A 3 Ee SEALS PTT 3 1 installing the SOMW ANG TT 32 UIMINSTANING ANE SOMW Te TTT So CODY POE CUON cicna a 34 DOwnoadiNg SOMWAN TTT 39 otaning Ne Sowar TTT 36 License updates usere ee ee eee ee 3 6 1 Installation of the License Manager Individual sse 3 6 2 License update without Internet ACCESS ese ee ee e eee seca eeeeeee eens 4 COMME ural Neasa ok betantetehiuat scat Men saa reae adidas tances 4 1 DOV OS eee ene et One en nee eee eS ee ne eee ee cre Aled GEREG 61 sel Le Tn snan a a r 4 1 1 1 Resetting settings esec eee eee eee c I E 21T ee e 65 26 060 D3534 D3534 208 06 02 02 06 2015 O CO O N N N OD DD OO LO E N ed ee e ok G
3. 1 Click the arrow at the right edge with the mouse and hold down the mouse button 2 Drag the camera view to enlarge or reduce it 3D Preview You can freely select the viewing direction of the virtual model in the 3D preview window by using the mouse Rotating the 3D preview 1 Click on the 3D preview with the left mouse button and hold it down 2 Move the mouse The 3D preview is rotated Moving the 3D preview 1 Click on the 3D preview with the right mouse button and hold it down 2 Move the mouse The 3D preview is moved Zooming into out of the 3D preview 1 Click on the 3D preview with the middle mouse button and hold it down 2 Move the mouse up or down as desired The 3D preview is enlarged or reduced 65 26 060 D3534 30 D3534 208 06 02 02 06 2015 Camera warm up time When switching on the system the camera needs to warm up for 15 20 minutes If the coated sapphire glass of the Omnicam is not sufficiently warm it may fog up during the acquisition As such it is not possible to carry out the exposure Following use always position the Omnicam on the heater plate From device serial number 121 001 you can now set the end temperature to which the camera heater warms the Omnicam mirror sleeve 1 In the software navigate to the system menu and click on the Contiguration button Click on the Devices button Click on the Omnicam button Click on the Camera Hea
4. The function Help can be used to open the help function Run application The function Run Application can be used to open the app center and to start plugins Close the software The Exit function can be used to close the software 65 26 060 D3534 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 6 Start window Operator s Manual CEREC Ortho SW 6 1 Creating a new patient Start Screen On the Start Screen you can perform the following e Search the database e Display patients e Add patients Switching to the Start Screen If you have a scan open you can switch to the Start Screen by closing the scan 1 Open the system menu K 2 Click onthe C ose button Ifthe current scan has not been saved a prompt appears asking if the scan should be saved 3 Confirm the prompt to save the scan The start window is displayed Creating a new patient In the data structure a patient is uniquely identified by one of the following two entries e Last name first name and date of birth or e Patient ID Adding patients 1 Click the Add New Patient button An empty patient card is opened 2 Enter a last name first name and date of birth or gt Enter the patient ID Once you have entered enough information the bar in the Edit Patient step turns from red to green 3 Click the Add new scan button Us N The program switches over to the ACQUISITION phase at
5. Sirona Registry Server Sirona Launcher and RequestScan components For more information about this see Sirona Server Operator s manual REF 65 39 725 IMPORTANT The Dolphin 3D software must be version 11 8 06 16 or higher IMPORTANT Exporting to Dolphin 3D is available if CEREC Ortho SW has been started via the Dolphin 3D software Click the Dolphin 3D button IMPORTANT If the scan is requested via Dolphin 3D exporting to Dolphin 3D starts automatically when switching to the EXPORT phase In this case clicking on the Do ohin 3D button is not required 2 Click the Add button in the window that appears 3 Inthe menu that appears select the menu option CEREC Ortho Scanner While the data is being sent to Dolphin 3D the Loading Arch Models Please wait message is displayed When the data is sent a confirmation message appears 4 Click the OK button in the confirmation message The data has been sent to Dolphin 3D and can be processed there Saving the model 1 Click on one of the S CAT Stratasys OnyxCeph 3M Incognito or CA Digital buttons 2 Select the storage location and change the file name if necessary 3 Click Save 65 26 060 D3534 48 D3534 208 06 02 02 06 2015 We reserve the right to make any alterations which may be required due to technical improvements Sirona Dental Systems GmbH 2015 Sprache englisch Printed in Germa
6. 7 Execute steps 5 and 6 a total of 11 times as directed by the software The software provides status updates on the calibration and informs you once the procedure is complete 65 26 060 D3534 18 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 4 Configuration Operator s Manual CEREC Ortho SW 4 1 Devices Measuring the position of the exit window 1 Mount the bottom side of the calibration set to the tip of the camera 2 Click the OK button on your CEREC AC The calibration process is continued Once the calibration is complete a message is displayed indicating this 3 Confirm the message by clicking the OAK button on your CEREC AC The CEREC Omnicam is calibrated Error message during calibration The software indicates if an error occurs during calibration If the calibration process resulted in errors restart the process End calibration v The software indicates that the calibration was completed successfully gt Click on the Ok button The CEREC Omnicam is calibrated 65 26 060 D3534 D3534 208 06 02 02 06 2015 19 20 te i TA Settings The menu item Settings has the following subitems e Resetting warning messages e Selecting a seating position e Settings for Sirona Server e Selecting a language e Database Reset warning messages Warnings may appear in pop up windows when using the software Many of these messages can be deactivated by clicking on the Do
7. 8 5 Performing a scan User guidance You are guided through the acquisition steps with tone signals and graphic displays 65 26 060 D3534 D3534 208 06 02 02 06 2015 Starting point for a scanning step Hold the camera over this marker for 3 seconds to start scanning the scanning step Resume the scan If the scan has been interrupted hold the camera over this marker to continue the scan Target area Guide the camera along the arrow into this area The partial scan does not end at an exact point End point of a quadrant Hold the camera over this marker for 3 seconds to mark the end point of the quadrant End point of a scanning step When this marker is reached the scanning step is complete If the camera has identified the start point of a partial scan the tone signal changes and the start marker is hidden The acquisition begins When a partial scan is finished a green check mark is displayed The guide direction for the camera is displayed with arrows If the automatic data flow is interrupted the tone signal changes and a start marker is displayed In this case guide the camera to the start marker As soon as the correct position has been found the tone signal changes and the start marker disappears The acquisition procedure starts 33 8 ACQUISITION phase Sirona Dental Systems GmbH 8 5 Performing a scan Operator s Manual CEREC Ortho SW Video animation There is an optional video animation which
8. Sending the model to Invisalign sse sese eee eee 104 Send lele hee c e Ti SD eerie nE AS 105 Saving ME mode karia a tease 65 26 060 D3534 D3534 208 06 02 02 06 2015 32 32 34 34 37 39 40 41 41 42 42 42 43 43 44 44 44 45 45 45 45 46 46 46 46 47 47 47 48 48 Copyright Trademarks Introduction Dear Customer Thank you for purchasing CEREC Ortho SW software from Sirona With CEREC Ortho SW in combination with the CEREC AC Omnicam acquisition unit you can create scans and send them to your partner laboratory via the Sirona Connect portal Any type of orthodontic appliance can be createdd based on CEREC digital impressions Improper use and handling can create hazards and cause damage Therefore please read and follow this document carefully You should always keep it within reach To prevent personal injury or material damage it is important to observe all safety information Your CEREC Ortho SW team Copyright and trademark Sirona Dental Systems GmbH All rights reserved The information contained in this manual may be changed without notice The software and all related documentation are protected by copyright You must therefore handle it in the same way as any other protected material Anyone who copies this software to any medium for any purpose other than his own personal use without the written permission of Sirona Dental Systems will be liable to prosecution
9. appliances manufactured using models from this software must be delivered to the patient by a trained individual For the USA only CAUTION According to US Federal Law this product may be sold only to or by instruction of physicians dentists or licensed professionals 2 General data Sirona Dental Systems GmbH 2 3 Structure of the manual Operator s Manual CEREC Ortho SW Structure of the manual Identification of danger levels To prevent personal injury and material damage please observe all warning and safety information provided in this document Such information is highlighted as follows DANGER An imminent danger that could result in serious bodily injury or death A possibly dangerous situation that could result in serious bodily injury or death A possibly dangerous situation that could result in slight bodily injury NOTICE A possibly harmful situation which could lead to damage of the product or an object in its environment IMPORTANT Application instructions and other important information Tip Information on making work easier Formats and symbols used The formats and symbols used in this document have the following meaning v Prerequisite Prompts you to do something 1 First action step 2 Second action step or gt Alternative action T Result gt Individual action step see Formats and symbols Identifies a reference to another text used gt 8 passage and specifie
10. filter below the list In order to view the order details you must click the relevant order in the list so that it is highlighted in orange Then you can view the details by clicking on View Order in the step menu Via the step menu you can call up individual items of information on the highlighted order Sending the model to Invisalign You can export a model to Invisalign via the Sirona Connect Portal directly into your customer account on the Invisalign Doctor Site http vip invisalign com Model data in the Sirona Connect Portal The Sirona Connect Portal saves the data only briefly The data is promptly deleted for data protection reasons v You are registered on www sirona connect com as a dentist 1 Log in at www sirona connect com 2 Under My account select the option Your Laboratories 3 Select Invisalign 4 Follow the instructions to carry out the authentication process Your Sirona Connect account is linked to your Invisalign customer account on Click the Invisalign button The model is uploaded and automatically filed to your Invisalign Doctor Site customer account 65 26 060 D3534 D3534 208 06 02 02 06 2015 47 10 EXPORT phase Sirona Dental Systems GmbH 10 4 Send model to Dolphin 3D Operator s Manual CEREC Ortho SW Send model to Dolphin 3D IMPORTANT In order to send a virtual model to Dolphin 3D the Sirona Server software must be installed and configured with the
11. marked area from the start marker A to the target marker B Ifthe connection is scanned a signal tone will be heard The software changes to the Crop Jaw step IMPORTANT Crop Jaw Areas of the mouth outside the jaw and other objects can have a negative impact on the accuracy and the speed of model reconstruction To avoid this in the Crop Jaw step you can cut the model to the area required for orthodontic planning The boundary is marked by a blue line When you change to the next step everything that is outside this line is cut off Parts of the anatomy which are removed in this step then later re scanned in Complete Jaw step are automatically deleted again 7 If necessary edit the blue boundary line of the model To do this double click the boundary line Pull and click to set additional points To stop editing the boundary line double click again Ensure that only the areas required for orthodontic planning are inside the boundary line 8 To confirm the boundary line click Ok in the sequence bar during the Crop Jaw step To reset changes made to the boundary line click Cance in the sequence bar during the Crop Jaw step 9 Change to step Complete Jaw The model is cut to the areas of the boundary line 10 Rescan the areas that have not been scanned yet This step is optional All areas that have not been scanned are marked in yellow C The lower j
12. 0 D3534 D3534 208 06 02 02 06 2015 11 2 General data Sirona Dental Systems GmbH 2 4 User interface Operator s Manual CEREC Ortho SW System menu In the system menu you can e Switch to the start window to start a new scan e Save scan e Save the scan under a different name e Import scan e Export scan e Call up App Center start plug ins e Open help function e Open license manager e Configure hardware and software e Change window mode e Retrieve software information e Close the software The start screen From the start screen you can perform the following e Search the database e Display patients e Add patients 65 26 060 D3534 12 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 3 Getting started Operator s Manual CEREC Ortho SW 3 1 Installing the software Getting started Installing the software v The PC is powered up and all programs are terminated v You have downloaded the installation file from the Internet and saved it to the device or the product disc is inserted in the CEREC AC s DVD ROM drive 1 Navigate to the location of the installation file 2 When the installation files were downloaded unzip the zip file and save the installation files 3 Double click the setup exe file 4 Select the language of the installation and click the button marked OK The installation wizard opens 5 Click on Next The license agreement is shown 6 Confirm the license agreem
13. 65 26 060 D3534 D3534 208 06 02 02 06 2015 25 6 Start window Sirona Dental Systems GmbH 6 2 Patient search Operator s Manual CEREC Ortho SW Patient search Displaying all patients The Show All Patients function can be used to display all patients Searching for individual patients You can view individual patients by searching for them a 1 Click into the search text box LAT 2 Enter the surname or the patient ID E 3 Click the magnifying glass to start The program now shows all the search results Editing patient data Editing a patient card v You have found the patient with the search function P 1 Click on the patient card 2 Click on the Edit Patient step in the step menu The patient card case view is opened for editing 3 Carry out the changes 4 Confirm your changes by clicking the Ok button The changes are saved in the database 5 Click the double arrow on the left side of the step menu The patient card case view is displayed Deleting patients v You have found the patient with the search function 1 Click on the patient card 2 Click on the De ete Patient step in the step menu 5 E 3 Confirm the deletion by clicking the Ok button _ The patient is deleted 65 26 060 D3534 26 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH Operator s Manual CEREC Ortho SW 7 Menu field 7 1 Views 65 26 060 D3534 D3534 208 06 02 02 06 2015 Tool Men
14. E 31 8 4 Taking acquisitions with the CEREC Omnicam css eee ee ee ee eee e 31 65 26 060 D3534 D3534 208 06 02 02 06 2015 8 9 S 21 e nall E SCAN THH 8 5 1 Procedure for the guided SCANNING DrOoCess css esse 8 92 olalt The SCall eee Gow LOWE AW SCAM sieges teres Geen ect oan ein ta Grete Mel ois cain aia eee o onthe 09 4 Upper aW SCAN TTT 99 9 BUCCAILECIS I ANON raeree ectact ite Memsesuer tale eeataneedtoattias 9 0 ST yle e ING sla T Q LE SL sls 9 1 T niee L ax SeT hada aaeaeeenseaenianak 9 27 Checking tne e 93 Eding ING UD DE aW Aen e a ese OA Editing the l wer JaW sxcncdcscccdsccacnie sa nnna aa a a a aa a eaa 9 9 Adding abase tothe MOdClsicciccc eee ees He a Aces 9 6 Finishing ING phase sesscnxgsiccdexeer voce eee coxa ode ee a veces eevee 10 90 2 61 0 72 oy eee rn eee een ee ee e eee a ee eee 10 1 Send model to Sirona Connect portal sese eee ee WOLD OGM TONS Ponal seare dl ute Seok cashier E T 1O12 Enerorderdald TTT 10 1 3 Add additional nformation sss sese IOTA SHODNO CARE sicain uneaiowgohean taaiealeanaeriedlutaelelnenvens 101S Order liS baci ne ee eee eee ne ee eee 10 2 Send model to Cle arCorr eC live ccc caciccstesesssvce cca vans sacs suvedvenvansexeteactanvesaaveaeiadeas 10 21 LOGAN TO me clen cat eect eetaten Nicaea ies ba eee ages aha tae 815 2 Emer order dala TTT 10 2 3 Add additional nformation sss esse eee ee 10 24 CSOD IGT eT TTT 1025 Order liSl TTT 10 3
15. In this step the contact points of both jaws are displayed in order to allow a check against the natural situation The colored displays of the contact points have the following meanings Penetration pressure W gt 100 um 100 50 um S 50 0 pum Distance S 0 50 Um S 50 100 um Mm gt 100um Editing the upper jaw In the Edit Upper step you can work with the following tool e Crop Model e Cut The use of the individual tools is described in the Menu field gt 27 section Editing the lower jaw In the Edit Lower step you can work with the following tool e Crop Model Fi Cut The use of the individual tools is described in the Menu field gt 27 section 65 26 060 D3534 42 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 9 MODEL phase Operator s Manual CEREC Ortho SW 9 5 Adding a base to the model Adding a base to the model You can add a base to the model in this step The following base types are possible e Tweed e Ricketts e Parallel e ABO To add a base proceed as follows 1 Switch to the Add Base step 2 Select a base type 3 Adjust the base to the upper and lower jaw using the arrows A You can adjust the height width and depth of the base The following base dimensions are displayed Maxilla base height Maxilla total height Mandible base height Mandible total height Total height model IMPORTANT Observe the minimum heights of the bas
16. Microsoft and Windows 7 are registered trademarks Windows is a trademark of Microsoft Corporation All other trademarks are the property of their respective holders Open source software This product contains open source software For more information please refer to the Licence pdf in the installation directory 65 26 060 D3534 D3534 208 06 02 02 06 2015 CE 65 26 060 D3534 D3534 208 06 02 02 06 2015 General data Please read this document completely and follow the instructions exactly You should always keep it within reach Original language of this document German Certification CE mark This product bears the CE marking in accordance with the provisions of Council Directive 93 42 EEC of June 14 1993 concerning medical devices General safety information Only use original software Only use original software or software which has been released by Sirona To produce restorations and equipment manipulated or non released software components must not be used Software and software components must not be installed using incorrect data Please check that each installed component has been granted approval in its country Contact your dealer for more information Models to be checked by trained personnel Every model created with this software must be checked for correctness by trained personnel e g orthodontist or dentist before it is digitally saved or exported for further use All orthodontic
17. R k ek MP KM X OOO 0 0 O OO aS sed Jaa seat oa A A BR WO O as ek eX ono on O E E E NOOO 42 55 11T s CTT 20 4 2 1 Reset Warning messages sese eee eee eee eee 20 Aiea SCAU eiee 20 A228 ONI OOLY TTT 20 4 2 4 Selecting a language sese eee eee eee 21 4 3 App Center ADDIICATIONS ssictesiwscidndoscadvarvaddmnteeeanotiesedinien nana debates 21 System MENU pia cease cea dice cose enna csciece baste lea cies aee ea nd ean za ap eamatee ss eaaeeuaetnde van dasabectaan 22 5 1 SAVE SCA TTT 22 5 2 Save the scan under a different NAME sss eee eee eee ee 23 Oro IMPOSANT T O A 23 TA EKDOR gt 9 TTT 23 O20 Eicense manager TT 24 eE COMMOUNAUO Miss TTT 24 Dif WWIII OW ModE T 24 959 ODEN MED TONGCHON aerae a a ae 24 29 Sae HI 216161 e 15161 24 oO ad ler 91 SOMWANE TT 24 Slit WINCOW ee sitieataatacsicetsal Sta Gene taconmiancs a O O 25 6 1 Crealing anew patient TTT 25 0A PatleMU e Te C 1 T 26 63 Ss Titel erz 17 T s 1 r TT 26 6 3 1 Editing a Dallent card 2 ccccsccscscsccwsgecret enpotigi ita aeea aia 26 692 Deleting pation serena e 26 IGT Hee ey aetna at Soto ee mee See eee ee 2 7 1 Va 2 De TOO aa cece atone Mumba are ade uae eo a neae 2 P IH CUPOUEIMOCE Al CAS aae 28 7 2 2 Cutting a model for orthodontic planning sss sese eee eee e eee e e ees 28 73 Displaying ODECE TT 29 ACQUISITION DNAS E T 30 8 1 CIMET VIEW e S 30 02 AD PreVEW eiee a O 30 039 Gamera wWalm Up IME sorie
18. asys OnyxCeph 3M Incognito CA Digital and SICAT 65 26 060 D3534 D3534 208 06 02 02 06 2015 Tool wheel The tool wheel makes the standard tools available in the MODEL phase in order to simplify access The tools currently available vary depending on the current step 1 Right click in the workspace The tool wheel opens 2 Click with the right mouse button anywhere in the workspace The tool wheel moves to the position of the mouse pointer 3 Selecta tool The selected tool is available The tool wheel closes automatically You also can close the tool by clicking in the workspace with the left mouse button Step menu The ACQUISITION and VODEL phases are divided into steps They are shown in the step menu at the bottom edge of the screen The step menu changes depending on which phase the current scan is in This menu guides you through the process step by step The double arrow keys can be used to switch between steps and phases Mandatory steps Mandatory steps are marked with a red or green bar Red bar The step has not yet been completed successfully Green bar The step has been completed successfully Users who have trouble discerning between the red and green can add a striped pattern to the red bars using the shortcut Ctrl Alt H Optional steps Optional steps do not have colored bars If you switch between the steps using the double arrow keys the optional steps are skipped 65 26 06
19. aw scan is finished 65 26 060 D3534 36 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 8 ACQUISITION phase Operator s Manual CEREC Ortho SW 8 5 Performing a scan Upper jaw scan Scanning the upper right quadrant v The lower jaw has been scanned 1 Click on the Upper Jaw scan object The Step Menu for scanning the upper jaw is displayed The first step Scan palatal right is selected in the Step Menu 2 Position the camera above the distal molar on the right of the upper jaw and hold the camera in this position to mark the start of the scan The start marker A which marks the starting point for the partial scan slowly disappears and the scan begins The guide direction for the camera is shown with an arrow 3 Turn the camera palatally and guide it in the direction of the arrow over the palatal surface of the teeth as far as the target marker B on the midline When the center line has been reached hold the camera in position once more for 3 seconds to mark the end point of the partial scan While doing so the target marker slowly disappears The software automatically changes to the next Scan occlusal right step 4 Position the camera above the distal molar on the right The starting point is marked with a start marker A and is automatically recognized Guide the camera occlusally as far as the target marker B on the midline Ifthe midline has been scanned a signal ton
20. describes the scanning procedure You can activate or deactivate the video animation in the configuration dialog for the Omnicam See CEREC Omnicam gt 16 Switching Omnicam on off You can switch the camera on off by clicking the Omnicam symbol in the bottom left PA ve Start the scan process v The correct working position is taken up v The teeth are blow dried gt Change to phase ACQUISITION Lower jaw scan Scanning the lower right quadrant 1 Remove the CEREC Omnicam from its holder The Step Menu for scanning the lower jaw is displayed Inthe Step Menu the first step Scan lingual right is selected 2 Position the camera above the distal molar on the right of the lower jaw and hold the camera in this position to mark the start of the scan The start marker A which marks the starting point for the partial scan slowly disappears and the scan begins The guide direction for the camera is shown with an arrow 3 Turn the camera lingually and guide it in the direction of the arrow over the lingual surface of the teeth as far as the target marker B on the midline When the center line has been reached hold the camera in position once more for 3 seconds to mark the end point of the partial scan While doing so the target marker slowly disappears The software automatically changes to the next Scan occlusal right step 4 Position the camera above the last molar on the right The s
21. e Operator s Manual CEREC Ortho SW 9 1 Set model axis MODEL phase In the WODEL phase the virtual models are reconstructed based on the acquired image catalogs The Set Model Axis step is required The Check Bite Edit Lower and Edit Upper steps are optional Set model axis Set the axes for model alignment This alignment is required to create optimal view options and define the occlusal plane when adding a model base 1 Align the model to the orientation of the jaw A Each tooth must be in its respective quadrant Align the incisors based on the displayed midline 2 Align the incisal edges and occlusal cusps along the displayed line B If necessary rotate the model by clicking on the display holding the mouse button down and dragging the model 3 Align the model for the occlusal plane C If necessary tilt the model by clicking on the display holding the mouse button down and dragging the model Information If you choose to create a planning model with base optional see Adding a base to the model gt 43 the set occlusion level is set parallel to the base level here With a standard base with an overall height of 60 mm the occlusion level is 30 mm away from the upper and lower foundation of the base 65 26 060 D3534 D3534 208 06 02 02 06 2015 41 9 MODEL phase Sirona Dental Systems GmbH 9 2 Checking the bite Operator s Manual CEREC Ortho SW Checking the bite
22. e required for 3D printing 4 When the base has been created confirm with the Apply button The color of the model with base changes Finishing the phase v The EXPORT phase can be selected gt Click onthe EXPORT phase or gt Click on the double arrow The program switches over to the EXPORT phase 65 26 060 D3534 D3534 208 06 02 02 06 2015 43 10 EXPORT phase Sirona Dental Systems GmbH 10 1 Send model to Sirona Connect portal Operator s Manual CEREC Ortho SW EXPORT phase In this phase you can perform the following 6 Send model to Sirona Connect portal e Send model to ClearCorrect e Send model to Dolphin 3D 6 Send model to Invisalign e Save model in different formats You can save the following formats Stratasys OnyxCeph 3M Incognito CA Digital Send model to Sirona Connect portal Model data in the Sirona Connect Portal The Sirona Connect Portal saves the data only briefly The data is promptly deleted for data protection reasons v YOU are registered on www sirona connect com as a dentist v in your account settings at least one favored laboratory is selected gt Click on the Sirona Connect Portal button Log in to the portal 1 Enter user name and password 2 Activate the relevant option if you want to save the user name and password 3 Inthe step menu click on Ok The data are uploaded in parallel to the information being entered in the po
23. e will be heard The software changes to the next Scan vestibular right step 5 Position the camera above the distal molar on the right The starting point is marked with a start marker A and is automatically recognized 6 Turn the camera towards the buccal and guide it in the direction of the arrow over the arch as far as the target marker B on the midline Ifthe midline has been scanned a signal tone will be heard The software changes to the next Scan transversal right step 7 Guide the camera in the direction of the arrow over the marked area from the start marker A as far as the target marker B Ifthe connection is scanned a signal tone will be heard The software changes to the next step Scan palatal left 65 26 060 D3534 D3534 208 06 02 02 06 2015 37 8 ACQUISITION phase Sirona Dental Systems GmbH 8 5 Performing a scan Operator s Manual CEREC Ortho SW Scanning the left hand quadrant and completing the upper jaw scan 1 Position the camera above the last molar on the left of the upper jaw and hold the camera in this position to mark the start of the scan The start marker A which marks the start of the scan slowly disappears and the scan begins The guide direction for the camera is shown with an arrow 2 Turn the camera lingually and guide it in the direction of the arrow over the lingual surface of the teeth to the target area B on the midline When the center
24. ent with the Yes button The program continues the installation routine 7 Select Full Installation NOTICE Installing DirectX If DirectX is not yet installed on your computer it will be installed now Accept the license agreement and decide whether the computer is to be restarted now or later 8 After installation you can display the ReadMe file by ticking or unticking the appropriate check box 9 Click on the Finish button Uninstalling the software v The program is closed 1 Click on Start All Programs Sirona Dental Systems CEREC Ortho Tools Deinstallation to uninstall the software During the uninstall procedure you will be asked whether you want to delete the patient data or the entries in the registration database e g the calibration data 2 Depending on your decision click either the Yes or No button The software is uninstalled 65 26 060 D3534 D3534 208 06 02 02 06 2015 13 Copy protection The software can be started only when the USB License Drive is inserted The USB License Drive is included with the delivery of the acquisition unit If you require additional licenses please contact your dealer Do not remove the USB License Drive from the acquisition unit All interface and software licenses can be installed on the USB License Drive You must enter a 25 digit license key to install new licenses You will receive the license key along with the acquis
25. he model can be cut off using the Cut function The cut plane lies orthogonal to the screen plane Removing the model area The Discard Part function enables model areas to be removed When performing this activity be careful not to accidentally cut out any areas that e g are located behind the model or are otherwise cut away from the line 1 Click on the Cut button 2 Begin the cut line with a double click 3 Click to set additional points 4 Finish the cut by double clicking The model area is cut off Inverting the model area With the nvert Selected function the model area that is cut out can be inverted v The Cut tool is selected v You have created a cut gt Click the nvert Selected button The model area which was cut out is displayed The rest of the model area is hidden Tip You can invert the model area that is cut out by double clicking on the semitransparent cut out area Cutting a model for orthodontic planning The Crop Model function can be used to remove unnecessary model areas A cut line is predefined With this cut line you can remove areas which are not required for orthodontic treatment and which are not removed during the ACQUISITION phase in step Crop Jaw You can edit the cut line When performing this activity be careful not to accidentally cut out any areas that are located behind the model or are otherwise cut away from the line for exa
26. irona ID You can find the ID on the sticker on the calibration set With all future calibration work involving the CEREC Ortho SW software you will be prompted to use this calibration set Starting calibration 1 In the software navigate to the system menu and click on the Contiguration button 2 Click onthe Devices button De Click on the Omnicam button 4 Click onthe Ca ibrate button The camera view is displayed in one window 5 Enter the 8 digit Sirona ID You can find this ID on the sticker on the calibration set 17 4 Configuration Sirona Dental Systems GmbH 4 1 Devices Operator s Manual CEREC Ortho SW Calibrate the camera 1 Remove the protective cap from the calibration set 2 Mount the calibration set on the tip of the camera until it locks into place 3 Secure the CEREC Omnicam in the calibration set using one hand Ensure that the external calibration set screw is fully screwed in ina clockwise motion until it gently locks into place 4 Click the OK button on your CEREC AC The measuring process starts The software prompts you to proceed to the next latching 5 Turn the screw counter clockwise until you reach the next latching point 6 Click the OAK button on your CEREC AC In doing so ensure that the CEREC Omnicam does not move The software confirms the calibration process The software prompts you to proceed to the next latching
27. ition unit Alternatively you can order it separately from your dealer Following an update you may require a new license that is not available on your USB License Drive For more information refer to the section on License Manager Downloading software Service packs IMPORTANT Auto updating service packs If the acquisition unit is connected to the internet a message appears which informs you about the service packs available To keep your software updated regularly check whether new service packs are available You can find information on current product versions and a description of the improvements and enhancements made in the service pack under Atto cerecortho com Starting the software v The CEREC Ortho SW software is installed You will find the start icon on the desktop v The USB License Drive is connected with a valid current license gt Double click the CEREC Ortho SW start icon or gt Click on Start All Programs Sirona Dental Systems CEREC Ortho CEREC Ortho SW The software is started 65 26 060 D3534 D3534 208 06 02 02 06 2015 License update For more information on the license manager refer to the section on License manager Installation of the License Manager Individual v The PC is powered up and all programs are terminated 1 Insert the DVD in the DVD drive The setup program starts automatically 2 Ifthis is not the case run the Sefup exe file in the
28. librate the CEREC Omnicam in the following cases e During the initial installation or following any other transport of the unit excessive vibration or shaking other than rolling on its own casters e after storage in unheated or un air conditioned rooms temperature differences exceeding 30 C 86 F e with temperature differences of over 15 C 25 F between the last calibration and operation 6 In general carrying out a calibration is recommended in the event of errors in the acquisition process such as poor image quality or the lack of a 3D preview In many cases the errors can be corrected in doing so Prior to the first calibration Ensure to take note of the serial number of the calibration set when starting the calibration which must be used at this point The number displayed in the software and the serial number on the calibration set must be identical The serial number of the calibration set to be used has been set on the CEREC AC with Omnicam at the factory Prior to the first calibration after changing the PC and when switching the calibration set you must enter the serial number of the calibration set to be used in the software If you do not wish to do this you can continue with Start calibration gt 17 When entering the serial number the following steps should be followed 1 Start the CalibRegistry exe application on the USB stick included with delivery of the calibration set 2 Enter the 8 digit S
29. line has been reached hold the camera in position once more for 3 seconds to mark the end point of the partial scan While doing so the target marker slowly disappears The software automatically changes to the next Scan occlusal left step 3 Position the camera above the last molar on the left The starting point is marked with a start marker A and is automatically recognized Guide the camera occlusally as far as the target marker B on the midline Ifthe midline has been scanned a signal tone will be heard The software changes to the next Scan vestibular left step 4 Position the camera above the last molar on the left and hold the camera in this position to mark the start of the partial scan 5 Turn the camera towards the buccal and guide it in the direction of the arrow over the arch as far as the midline Ifthe midline has been scanned a signal tone will be heard The software changes to the next Scan transversal left step 6 Guide the camera in the direction of the arrow over the marked area Ifthe connection is scanned a signal tone will be heard The software changes to the Scan Palate step 7 Scan the roof of the mouth To do this begin at the start marker and guide the camera over the roof of the mouth This step is optional 8 Change to step Crop Jaw 65 26 060 D3534 38 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 8 ACQUISITION phase Operator s Ma
30. mple 1 Click the Crop Model button Double click the blue boundary line Click to set additional points Finish changing the boundary line by double clicking Click the Apply button to implement the change to the boundary line ae SN The model is cut on the boundary line 65 26 060 D3534 28 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 7 Menu field Operator s Manual CEREC Ortho SW 7 3 Displaying objects Displaying objects Upper jaw With the Upper Jaw button you can display and hide the upper jaw 1 Click on the View Options button 2 Click on the Upper Jaw button The upper jaw is displayed or hidden Lower jaw With the Lower Jaw button you can display and hide the lower jaw 1 Click on the View Options button a 2 Click onthe Lower Jaw button s The lower jaw is displayed or hidden Display upper lower jaw transparently You can adjust the transparency of the upper lower jaw continuously 1 Click on the View Options button 2 Place the mouse pointer on the appropriate button press and hold the left mouse button and move the mouse up or down The transparency of the jaw concerned is changed 65 26 060 D3534 D3534 208 06 02 02 06 2015 29 8 ACQUISITION phase Sirona Dental Systems GmbH 8 1 Camera view Operator s Manual CEREC Ortho SW ACQUISITION phase Camera view You can adjust the size of the camera view proportionally
31. n t show this message again check box If this check box has been inadvertently selected or if a new user uses the software all warnings can be reset here All warnings are then displayed Displays all the deactivated warnings in the workflow again Warnings which were previously hidden remain hidden Seat position Here you can adjust the position of the user relative to the patient For this the alignment of the upper jaw and lower jaw on the screen and the direction of movement for the camera view are defined These are adjusted to the user s view of the patient s upper and lower jaw You have the following options e Always next to or facing The user is next to or opposite the patient while the upper jaw and lower jaw are being scanned The camera is held with the lens pointing downward for the lower upward for the upper jaw e Facing for lower behind for upper The user is opposite the patient while the lower jaw is being scanned The user is behind the patient while the upper jaw is being scanned The camera is held with the lens pointing downward for both jaws e Always behind The user is behind the patient while the upper jaw and lower jaw are being scanned The camera is always held with the lens pointing downward Sirona Server You can determine the IP settings for the Sirona Server software here You can determine the IP address automatically or enter it manually For more information on the Sir
32. nstallation the step specific help opens automatically If the lightbulb is not illuminated in yellow there is no step specific help available You can access the manual via the Help button or by pressing F1 You will find the Operator s Manual on the Internet in PDF format 6 htto cerecortho com You can download the current manual in the DOWNLOADS Downloads area 6 http www sirona com manuals This format is page oriented and is well suited for printing out the desired pages 2 General data Sirona Dental Systems GmbH 2 4 User interface 2 4 2 4 1 2 4 1 1 2 4 1 2 2 4 1 3 2 4 1 4 10 Operator s Manual CEREC Ortho SW User interface Phase bar Description For CEREC Ortho SW the digital scan process is divided into three phases ACQUISITION In this phase you can perform the following e Create optical impressions with CEREC Omnicam Lower jaw Upper jaw Buccal bite registration e View a 3D preview of the scans MODEL In this phase you can perform the following e Set the model axis e Check the bite situation e Edit the virtual models if required e Add a base to the model EXPORT In this phase you can perform the following e Log on to the Sirona Connect portal and transfer models to the laboratory of your choice e Send model to Dolphin 3D e Send model to ClearCorrect Send model to Invisalign e Save the model formats for Strat
33. nual CEREC Ortho SW 8 5 Performing a scan IMPORTANT Crop Jaw Areas of the mouth outside the jaw and other objects can have a negative impact on the accuracy and the speed when creating the model To avoid this in the Crop Jaw step you can cut the model to the area required for orthodontic planning The boundary is marked by a blue line When you change to the next step everything that is outside this line is cut off Parts of the anatomy which are scanned in areas that have already been cut off during the Complete Jaw step are also cut off 9 If necessary edit the blue boundary line of the model To do this double click the boundary line Pull and click to set additional points To stop editing the boundary line double click again Ensure that only the areas required for orthodontic planning are inside the boundary line 10 To confirm the boundary line click Ok in the sequence bar during the Crop Jaw step To reset changes made to the boundary line click Cance in the sequence bar during the Crop Jaw step The model is cut to the areas of the boundary lines 11 Rescan the areas that have not been scanned yet This step is optional All areas that have not been scanned are marked in yellow C The upper jaw scan is finished Buccal registration v The lower jaw and upper jaw have been scanned 1 Click the Buccal scan object The sequence bar for
34. ny D3534 208 06 02 02 06 2015 A Nr 120 968 Sirona Dental Systems GmbH in the USA FabrikstraBe 31 Sirona Dental Systems LLC Order No 65 26 060 D3534 D 64625 Bensheim 4835 Sirona Drive Suite 100 Germany Charlotte NC 28273 WWW sirona com USA
35. ocation v You have opened a scan 1 Select Export A standard Windows file dialog box opens Select the target folder to which you want to export the scan Assign any name to the scan Click on the Save button The scan is exported oo IS If you want to transfer the scan from your acquisition unit to another PC e g in order to upload it to the Web portal you can use a USB stick for this purpose 65 26 060 D3534 D3534 208 06 02 02 06 2015 23 kad License Manager The License Manager is used for the installation of new software licenses on the USB license stick To do this start the License Manager via the system menu and follow the instructions on the screen Keep the license certificate with 25 digit license key ready which you either obtained with the unit or ordered separately from your dealer Tip You can also start the license manager via Start All Programs Sirona Dental Systems CEREC Ortho SW Tools License Manager To activate the license you must have an Internet connection and the USB License Drive must be inserted Licenses and code libraries For information on licenses and code libraries from third parties see licenses pdf The file is in the installation directory Configuration The configuration is described in the chapter Configuration Window mode The Window Mode function can be used to exit full screen mode or enter it again Open help function
36. of the scan slowly disappears and the scan begins The guide direction for the camera is shown with an arrow Turn the camera lingually and guide it in the direction of the arrow over the lingual surface of the teeth to the target area B on the midline When the center line has been reached hold the camera in position once more for 3 seconds to mark the end point of the partial scan While doing so the target marker slowly disappears The software automatically changes to the next Scan occlusal left step Position the camera above the last molar on the left The starting point is marked with a start marker A and is automatically recognized Guide the camera occlusally as far as the target marker B on the midline Ifthe midline has been scanned a signal tone will be heard The software changes to the next Scan vestibular left step Position the camera above the distal molar on the left The starting point is marked with a start marker A and is automatically recognized Turn the camera towards the buccal and guide it in the direction of the arrow over the arch as far as the target marker B on the midline Ifthe midline has been scanned a signal tone will be heard The software changes to the next Scan transversal left step 35 8 ACQUISITION phase Sirona Dental Systems GmbH 8 5 Performing a scan Operator s Manual CEREC Ortho SW 6 Guide the camera in the direction of the arrow over the
37. ona Server see Sirona Server Operator s manual REF 65 39 725 65 26 060 D3534 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 4 Configuration Operator s Manual CEREC Ortho SW 65 26 060 D3534 D3534 208 06 02 02 06 2015 4 3 App Center applications Selecting a language Here you can set the language of the software The software must be restarted for a language change to take effect App Center applications Via the Sirona App Application Center you have access to various apps applications for our CAD CAM products Furthermore you have access to a website that shows you the apps available The website also contains additional information on where you can download the apps 21 5 System menu Sirona Dental Systems GmbH 5 1 Save scan Operator s Manual CEREC Ortho SW System menu In the system menu you can e Close the current scan and switch to the start screen e Save scan e Save scan as e Import scan e Export scan e Run application e Open License Manager e Configure hardware and software e Toggle window modes 6 Open the help contents e Close the software Opening system menu gt Move the mouse cursor to the top of the window or gt Click the start window button The system menu is displayed Closing system menu gt Click the start window button or gt Click into the main window with the left mouse button The system menu is closed Save scan In
38. rd and confirm it with Ok The order list is then inserted automatically Order list All sent orders are displayed in the order list The most recently sent order is always at the top You can filter the orders by the various statuses via the filter below the list In order to view the order details you must click the relevant order in the list so that it is highlighted in orange Then you can view the details by clicking on View Order in the step menu Via the step menu you can call up individual items of information on the highlighted order 45 10 EXPORT phase Sirona Dental Systems GmbH 10 2 Send model to ClearCorrect Operator s Manual CEREC Ortho SW Send model to ClearCorrect Exporting a model to ClearCorrect occurs via the Sirona Connect Portal Model data in the Sirona Connect Portal The Sirona Connect Portal saves the data only briefly The data is promptly deleted for data protection reasons v YOU are registered on www sirona connect com as a dentist v in your account settings ClearCorrect is selected as a favored laboratory gt Click on the C earCorrect button Log in to the portal 1 Enter user name and password 2 Activate the relevant option if you want to save the user name and password 3 Inthe step menu click on Ok The data are uploaded in parallel to the information being entered in the portal Enter order data You can enter the desired delivery date in thi
39. root directory of the DVD The installation wizard opens 3 Click on the OA button 4 Inthe next dialog click the Next button The license agreement is shown 5 Read through the license agreement carefully 6 If you accept the license agreement then activate the accept the terms in the license agreement option button and click the Next button 7 Inthe next dialog click the Custom button 8 Uncheck all options apart from the license manager 9 Inthe next dialog click the Next button 10 In the next dialog click the nsfa button The program continues the installation routine This may take several minutes 11 Click the Finish button once installation is complete The license manager is installed License update without Internet access If the Sirona acquisition unit does not have Internet access itself you can run the License Manager on another PC with Internet access You need to remove the USB License Drive from the Sirona acquisition unit and plug it into the PC with Internet access The USB License Drive is behind the lower cover at the rear side of the Sirona acquisition unit Install the License Manager on the PC with Internet access and run the license update 65 26 060 D3534 D3534 208 06 02 02 06 2015 15 4 Configuration Sirona Dental Systems GmbH 4 1 Devices Operator s Manual CEREC Ortho SW Configuration The Configuration button is located in
40. rtal 65 26 060 D3534 44 D3534 208 06 02 02 06 2015 65 26 060 D3534 D3534 208 06 02 02 06 2015 Enter order data In this step you can select the lab to which the case is to be sent and enter the desired delivery date IMPORTANT Maximum 5 labs You can save a maximum of 5 labs in the list of your favorite labs Via Edit your favourite laboratories you can add labs to or delete labs from the list Under Return Date you can select the delivery date by clicking on the desired day in the calendar Under 7ime you can also state a delivery time Then click on Add Additional Information to go on to the next step Add additional information In this step you must add the patient s gender and insurance type Germany only Under Additional Instructions there is a free text field available for additional written information Using the Additional Files function you can send additional files photos Then click Update list to move to the shopping cart Shopping cart In the shopping cart you can check the order details modify them or delete the order from the shopping cart Your current delivery and invoice address is displayed In the top left corner you can see the progress for loading the model file As soon as the file has been fully uploaded and all the information is correct you can send the order to your lab via Submit Cart To do so under Verification you must enter your passwo
41. s its page number Command menu item Indicates commands menu items or quotations 65 26 060 D3534 8 D3534 208 06 02 02 06 2015 65 26 060 D3534 D3534 208 06 02 02 06 2015 Conventions Sanges eas O Clicking Pressing once and releasing the left mouse button or the left trackball button on the acquisition unit or foot switch Double clicking Pressing twice quickly in succession and releasing the left mouse button or the left trackball button on the acquisition unit or foot switch Moving the mouse On the acquisition unit Moving the trackball in the in one direction corresponding direction Seizing a point Pressing the left mouse button left trackball button on the acquisition unit and eon it pressed Ctrl N On the keyboard Press the Ctrl and N keys simultaneously Drag amp drop Drag amp drop Press and hold an element e g pictograph and drop onto new potential destination Formats of the manual Step specific help The step specific help explains the aims and implementation of the current step There is a full view which provides a complete overview and a window view which leaves most of the screen free so you can see the help content while working An illuminated lightbulb indicates that this help is available By clicking on the lightbulb illuminated in yellow in the phase bar you can access the step specific help When accessing the ACQUISITION phase for the first time after i
42. s step Under Return Date you can select the delivery date by clicking on the desired day in the calendar Under 7ime you can also state a delivery time Then click on Add Additional Information to go on to the next step Add additional information In this step you must add the patient s gender and insurance type Germany only Under Additional Instructions there is a free text field available for additional written information Using the Additional Files function you can send additional files photos Then click Update list to move to the shopping cart 65 26 060 D3534 46 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 10 EXPORT phase Operator s Manual CEREC Ortho SW 10 3 Sending the model to Invisalign Shopping cart In the shopping cart you can check the order details modify them or delete the order from the shopping cart Your current delivery and invoice address is displayed In the top left corner you can see the progress for loading the model file As soon as the file has been fully uploaded and all the information is correct you can send the order to your lab via Submit Cart To do so under Verification you must enter your password and confirm it with Ok The order list is then inserted automatically Order list All sent orders are displayed in the order list The most recently sent order is always at the top You can filter the orders by the various statuses via the
43. tarting point is marked with a start marker A and is automatically recognized Guide the camera occlusally in the direction of the arrow as far as the target marker B on the midline Ifthe midline has been scanned a signal tone will be heard The software changes to the next Scan vestibular right step 65 26 060 D3534 34 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 8 ACQUISITION phase Operator s Manual CEREC Ortho SW 65 26 060 D3534 D3534 208 06 02 02 06 2015 8 5 Performing a scan Position the camera above the last molar on the right The starting point is marked with a start marker A and is automatically recognized Turn the camera towards the buccal and guide it in the direction of the arrow over the arch as far as the target marker B on the midline Ifthe midline has been scanned a signal tone will be heard The software changes to the next Scan transversal right step Guide the camera in the direction of the arrow over the marked area from the start marker A to the target area B Ifthe connection is scanned a signal tone will be heard The software changes to the next left hand quadrant step Scanning the lower left quadrant and completing the lower jaw scan 1 Position the camera above the last molar on the left of the lower jaw and hold the camera in this position to mark the start of the scan The position marker A which marks the start
44. ter Settings button oe S amp S bh Use the slider to adjust the temperature Taking acquisitions with the CEREC Omnicam Hot surface The output window of the CEREC Omnicam is preheated in the camera holder When removing the CEREC Omnicam from its holder the surface temperature of the mirror sleeve can be up to 51 C This may cause an unpleasant heat sensation on contacting a person s skin or mucous membrane These temperatures will not damage anyone s skin or mucosal membrane After removing the CEREC Omnicam from its camera holder the temperature of the mirror sleeve drops within a number of minutes lt 5 minutes to less than 43 C 109 F The CEREC Omnicam is therefore suitable for use in the patient s mouth for an unlimited period of time At an ambient temperature from 30 C 86 F only select the three lower heater settings NOTICE Image brightness The image brightness during the acquisition is controlled automatically so that there is always optimum image brightness largely independent of the distance between the CEREC Omnicam and the tooth The surroundings of the tooth to be scanned should be as weakly illuminated as possible Avoid any type of external light Switch off the operating light IMPORTANT Do not use cotton rolls in the scan area Do not use any cotton rolls in the vicinity of the scan area Should any pieces of cotton roll contaminate this area the acquisitions will be inaccurate
45. the buccal registration is displayed 2 Perform the buccal registration on the right side by having the patient bite as required and guiding the camera from the start marker A to the target area B IMPORTANT As the jaw models are displayed with a distance from one another before the first bite is scanned the target symbol appears lower in relation to the lower jaw during scanning than it is in reality gt Before scanning observe the position of the target marker in the upper jaw between the premolars and the molars in the figure and scan this region in the mouth As soon as the buccal registration is finished a signal tone will be heard The software changes to the next Scan buccal left step 65 26 060 D3534 D3534 208 06 02 02 06 2015 39 8 ACQUISITION phase Sirona Dental Systems GmbH 8 6 Finishing the phase Operator s Manual CEREC Ortho SW 3 Perform the buccal registration on the left side by guiding the camera from the start marker A to the target marker B As soon as the buccal registration is finished a signal tone will be heard Finishing the phase v All required scans have been performed lower jaw upper jaw buccal registration v The MODEL phase can be selected gt Click onthe MODEL phase or gt Click on the double arrow The program switches over to the WODEL phase 65 26 060 D3534 40 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 9 MODEL phas
46. the system menu The Configuration menu contains the following submenus e Devices e Settings Close the Configuration menu by clicking on the Exit Configuration button Devices All connected devices can be displayed and configured under the menu item Devices A green check mark on a device indicates its availability CEREC Omnicam Audio feedback Using the Sound selection box you can switch the audio feedback for acquisitions on or off You can control the volume using the slide bar 3 different tone varieties are available Virtual camera animation during scanning Here you can determine whether a video animation is displayed to help during the scanning process Accepting settings gt Click onthe Ok button Discarding settings gt Click on the Cancel button Resetting settings gt Click on the Reset Camera Settings button The settings are reset to factory settings 65 26 060 D3534 16 D3534 208 06 02 02 06 2015 65 26 060 D3534 D3534 208 06 02 02 06 2015 Calibration The measurement procedure used by the system requires the use of a calibrated CEREC Omnicam The CEREC Omnicam is factory calibrated Calibration should be repeated after every reinstallation and after every transport using the calibration set supplied with the CEREC Omnicam In order to achieve optimum results the CEREC Omnicam must be allowed to warm up for 15 20 minutes before calibration Reca
47. this dialog you can save the current scan gt Select Save in the system menu The scan is saved 65 26 060 D3534 22 D3534 208 06 02 02 06 2015 Sirona Dental Systems GmbH 5 System menu Operator s Manual CEREC Ortho SW 5 2 Save the scan under a different name Save the scan under a different name This dialog allows you to save the current scan under a new name or assign it to a different patient 1 Select Save As in the system menu The Save as dialog box opens 2 Enter a name for the scan 3 Select the appropriate patient 4 Click on the OAK button Import scan v A CEREC Ortho SW scan is located on your acquisition unit or removable media 1 Click on the mport button in the system menu A standard Windows dialog box opens 2 Select the folder where the scan is located 3 Select the relevant file NOTICE File types If the selected file ortho orthoimg or dxd is an optical impression with the CEREC Ortho SW software it will be opened If not it will not open and an error message will be displayed Scans which were not created with the CEREC Ortho SW Guided Scanningprocess can not be imported for orthodontic use 4 Click the Open button 5 Assign a name to the scan 6 Click the OA button The scan is now imported and opened Export scan You can save an optical impression in a compressed format in any l
48. u The tool menu offers you various different functions depending on the current step Views Global You can use the View Options button to display six predefined views in the Global area e Top e Bottom e Right e Left e Anterior e Posterior Changing the view 1 Click on the View Options button 2 Click on one of the proposed views The virtual model rotates to the corresponding view Enlarge or reduce the view 1 Click on the View Options button 2 Position the mouse pointer over the center tooth icon and press and hold the left mouse button The icon then changes to a magnifying glass 3 Pull the mouse button up or down The virtual model is then enlarged or reduced Tip You can also use the center mouse button and the trackball directly on the virtual model to enlarge or reduce a view Tools The most important tools are also offered to you in the tool wheel For more information on the tool wheel refer to the section Tool wheel You will find all tools as a submenu under 7oo s Tip You can cancel the current tool with the stop icon top right Undo and reset With the Undo button in the tools you can undo the last change made With the Reset button in the tools you can reset changes that were made with the tool 2 7 Menu field Sirona Dental Systems GmbH 7 2 Tools Operator s Manual CEREC Ortho SW Cut out model areas Regions of t
Download Pdf Manuals
Related Search