7R BEAM USER MANUAL 7R BEAM 230W
Contents
1. Gobo wheel replaceable gobo wheel with 17 fixed gobos open Lamp system with a short arc burner in a reflector Motors 11 stepper 2 phase motors operating with microsteps totally microprocessor controlled Channels 16 20 control channels Inputs DMX 512 Movable body Movement by means of two stepper motors Controlled by microprocessor Automatic repositioning of PAN and TILT after Accidental movement not controlled by control unit Travel PAN 540 TILT 252 e Maximum speeds PAN 2 45 sec TILT 1 30 sec e Resolution PAN 2 11 PAN FINE 0 008 TILT 0 98 TILT FINE 0 004 IP20 protection rating Protected against the entry of solid bodies larger than 12mm 0 47 No protection against the entry of liquids CE Marking In conformity with the European Union Low Voltage Directive 2006 95 CE and Electromagnetic compatibility Directive 2004 108 CE Safety Devices e Bipolar circuit breaker with thermal protection e Automatic break in power supply in case of Overheating or failed operation of cooling system Cooling Forced ventilation with axial fans Body e Aluminum structure with die cast plastic cover Two side handles for transportation Device locking PAN and TILT mechanisms for Transportation and maintenance Weights about 17 Kg Overview 1 Lens 2 LCD Display 3 Rotating button button 4 Down 5 Up 6 Handle 7 3 pin DMX IN2. 8 3 pin DMX OUT 9 5 pin DMX IN 10 5 pin DMX OUT 11 Power supply 12 Switch SAFETY INSTRUCTIONS CAUTION AN Be careful with your operations With a dangerous voltage you can suffer a dangerous electric shock when touching wires This device has left the factory in perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual A Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems If the device has been exposed to temperature changes due to environmental changes do not switch it on immediately The arising condensation could damage the device Leave the device switched off until it has reached room temperatures This device falls under protection class Therefore it is essential that the device be earthed The electric connection must carry out by qualified person Make sure that the available voltage is not higher than stated at the end of this manual Make sure the power cord is never crimped or damaged by sharp edges If this would be the case replacement of the cable must be done by an authorized dealer Always disconnect from the mains when the device is not in use or before cleaning it Only handle the power cord by the plug Never pull out the plug by tu
3. Val in this menu option 2 6 Lamp Control In the main menu select Lamp Control You can Turn Lamp On Of in this menu option 2 7 Display Opt In the main menu select Display Opt 2 7 1 Display Mode Off AfterDly means the LCD will automatically turn off after idling for 20 seconds On Always means the LCD will keep light up always 2 7 2 Display Inv Set this option to On the LCD will display inverse 2 7 3 Language There are English and Chinese c for options 2 8 Personality In the main menu select Personality You can set Pan Move On Off and Tilt Move On Off in this menu option 2 9 Operation In the main menu select Operation You can select DMX Signal Master Mode Slave Mode and Static Scene in this menu option Operation Selected this Mode fixture will be controlled by DMX signal Mode DMX Signal Operation Md You can select User Memo 1 User Memo 2 and Preset Master Mode Memo in this option User Memo 1 Operation Md You can select User Memo 1 User Memo 2 and Preset Slave Mode Memo in this option User Memo 1 Operation Md Selected this Mode fixture will run preset scene without DMX signal Static Scene 2 10 User Memory In the main menu select User Memory You can select Edit USER Mo to edit User Memory 1 amp 2 or select Init USER Mo to
4. initialize the edited user memory Each user memory can be edited with up to 32 scenes 16 channel CH1 0 125 Color choose 126 196 Color clockwise 197 255 Clock anti clockwise CH2 0 255 Stop Strobe CH3 0 255 Dimmer CH4 0 122 Gobo choose 123 190 Gobo clockwise 191 255 Gobo anti clockwise CH5 0 255 Prism Insertion CH6 0 255 Prism Insertion CH7 0 240 Effects Movement Unused 245 255 CH8 0 255 Frost CH9 0 255 Focus CH10 0 255 Pan CH11 0 255 Pan Fine CH12 0 255 Tilt CH13 0 255 Tilt Fine CH14 0 255 Function Unused CH15 0 255 Reset CH16 0 99 nothing 100 105 lamp OFF 200 205 lamp ON 206 255 Reset The above actions need to stay for a few seconds CLEANING AND MAINTENANCE The following points have to be considered during the inspection 1 All screws for installing the devices or parts of the device have to be tightly connected and must not be corroded 2 There must not be any deformations on the housing color lenses Fixations and installations spots ceiling suspension trussing 3 Mechanically moved parts must not show any traces of wearing and must not rotate with unbalances 4 The electric power supply cables must not show any damage material fatigue or sediments Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed CAUTION AN Disconnec
5. 7R BEAM USER MANUAL 7R BEAM 230W KEEP THIS MANUAL FOR FUTURE NEEDS C For your own safety please read this user manual carefully before installing the device In order to install operate and maintain the lighting safety and correctly We suggest that the installation and operation should be done by the certified technician and follow the instruction strictly CAUTION Keep this device away from rain and moisture CAUTION Unplug mains lead before opening the housing Every person involved with the installation operation and maintenance of this device has to be qualified follow carefully the instructions of this manual INTRODUCTION You will see you have acquired a powerful and versatile device Unpack the device Inside the box you should find 1 One XLR connection cable 2 Two omega clamps 3 One safety rope Please check carefully that there is no damage caused by transportation Should there be any consult your dealer and don t install this device TECHNICAL INFORMATION e Type OSRAM LAMP Output Lamp power 230W Colour temperature 8000 K Luminous flux 7 950 Im Average life 2000 h Any working position Cooing Forced ventilation with axial fans e Zoom from zero to 3 8 Selectable Prism 8 facet prism LCD control panel with setting and addressing function customized Light output at 20 meters 65 feet 59 760 lux Color wheel replaceable color wheel with 14 colors open
6. d to extreme heat moisture or dust Please don t project the beam onto combustible substances The minimum distance between light outoput from the projector and the illuminated surface must be more than 0 5 meter If you use the quick lock cam in hanging up the fixture please make sure the quick lock fasteners turned in the quick lock holes correctly Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported For safety reasons please be aware that all modifications on the device are forbidden If this device will be operated in any way different to the one described in this manual the product may suffer damages and the guarantee becomes void Furthermore any other operation may lead to short circuit burns electric shock lamp explosion crash etc INSTALLATION INSTRUCTIONS a Installing or replacing the lamp CAUTION The lamp has to be replaced when it is damaged or deformed AN CAUTION Only install the lamp with the device unplugged from the mains Before replacing the lamp let the lamp cool down because during operation the lamp can reach very high temperature During the installation of halogen lamps do not touch the glass bulbs bare handed Always use a cloth to handle the lamps during i
7. gging the power cord During initial start up some smoke or smell may arise This is a normal process and does not necessarily mean that the device is defective it should decrease gradually Please don t project the beam onto combustible substances If the external flexible cable or cord of this luminaire is damaged it shall be exclusively replaced by the manufacturer or his service agent or a similar qualified person in order to avoid a hazard CAUTION D Never touch the device during operation The housing may heat up CAUTION Never look directly into the light source As sensitive persons may suffer an epileptic shock Please be aware that damages caused by manual modifications to be the device are not subject to warranty Keep away from children and non professionals GENERAL GUIDELINES This device is a lighting effect for a professional use on stages in clubs theatres etc the device was designed for indoor use only This fixture is only allowed to be operated with the max alternating current which stated in the technical specifications in the last page of this manual Lighting effects are not designed for permanent operation Consistent operation breaks may ensure that the device will serve you for a long time without defects Do not shake the device Avoid brute force when installing or operating the device While choosing the installation spot please make sure that the device is not expose
8. ns the LCD will prompt Sure Reset At this time press ENTER to confirm or press MENU to cancel Factory Rst means to recover the fixture to the factory setting When you select this option the LCD will prompt Sure Restore Press 2 3 4 At this time you need to press the three buttons DOWN ENTER and UP all together and hold for a while to confirm the operation or press MENU only to cancel 2 4 DMX Config In the main menu select DMX Config to set the running mode of the fixture with DMX connection or without DMX connection 2 4 1 DMX Mode There are DMX Mode 1 2 and 3 and User Mode 1 and 2 for options The two User Modes can be defined in 2 4 2 No DMX Signal User Define Channel 2 4 2 No DMX Signal BEAM SPOT When DMX signal was cut off after a period of time all the Time Out channels will turn to zero state Clear Data BEAM SPOT When DMX signal is cut off fixture will hold the last state No Signal Hold Last BEAM SPOT User Define Channel 1 amp 2 are respectively to define User User Define Mode 1 amp 2 At Define 18 CH you can define the total Channel channels of the of the fixture BEAM SPOT To clear User Define it will prompt you to Unlock 2 3 4 User Define press DOWN ENTER and UP all together Clear 2 5 Information In the main menu select Information You can check Lamp Hours Total Hours and View DMX
9. nsertion and removal Do not install lamps with a higher wattage They generate higher temperatures than which the device was designed for For the installation you need one PLATINUM 5R LCD DISPLAY AND TOUCH BUTTONS When the fixture is powered on or resetting the LCD will show BEAM SPOT Reset After resetting and if the fixture is connected to a DMX console the LCD will show BEAM SPOT DMX Receive ADDR 001 Now the fixture is ready for work ADDR indicates the current DMX address code of the fixture MENU OPERATION 2 1 Main menu options The main menu options of TRMH 5R include DMX Address Reset DMX Config Information Lamp Control Display Opt Personality Operation and User Memory 2 2 DMX Address In the main menu select DMX Address the LCD will show BEAM SPOT DMX Address 001 Now the DMX address code of the fixture is ready for setting Press UP DOWN to adjust the value Press ENTER to confirm The DMX address code can be set within 001 512 2 3 Reset In the main menu select Reset There are three sub options All Reset Internal Rst and Factory Rst press UP DOWN to browse BEAM SPOT BEAM SPOT BEAM SPOT All Reset Internal Rst Factory Rst All Reset means to reset everything of the fixture Internal Rst means to reset fixture without pan and tilt When you select one of these two optio
10. t from mains before starting maintenance operation In order to make the lights in extend the life time we suggest a regular cleaning to the lights 1 Clean the inside and outside lens each week to avoid the weakness of the lights due to accumulation of dust 2 Clean the fan each week 3 To make sure the smooth gobo rotation we suggest adding proper lube to the wheel each three month avoiding the excessive lube splashes during the gobo rotating 4 A detailed electric check by approved electrical engineer each three month make sure that the circuit contacts are in good condition prevent the poor contact of circuit from overheating We recommend a frequent cleaning of the device Please use a moist lint free cloth Never use alcohol or solvents There are no serviceable parts inside the device except for the lamp Please refer to the instructions under Installation instructions Should you need any spare parts please order genuine parts from your local dealer REMARK Errors and omissions for every information given in this manual accepted All information is subject to change without prior notice 11
Download Pdf Manuals
Related Search