Model 733062 VC-SHIELD Shield Box
Contents
1. measure parameters such as the transmission power of the mobile phone connect the mobile phone and the shield box with a coaxial cable Do not insert foreign objects between the shield box and the lid The shield box may break or may not achieve the shielding performance of the specifications Check that there is no deformation or damage inside and outside the shield box If the shield box is deformed or damaged the shielding performance of the specifications may not be achieved Recommended Replacement Parts The one year warranty applies only to the main unit starting from the day of delivery and does not cover any other items nor expendable items items which wear out Contact your nearest YOKOGAWA dealer to have parts replaced Parts Name Part No Damper B8014GN Gasket B8014VF Gasket B8014VG Gasket B8014VH IM733062 01E Specifications Shielding Performance Item Specifications Frequency range 800 M to 2500 MHz Shielding Performance 60 dB or higher Antenna coupler Item Specifications Frequency range 800 M to 2500 MHz Antenna coupling loss 30 dB or less Coupling impedance 50 O Maximum allowable input power 0 25 W Connector type N type connector rear side ANT connector of RF IN OUT Varies depending on the shape of the mobile phone antenna position and the holder slide position RF IN OUT Connector CABLE Item Specifications Frequency2. range 800 M to 2500 MHz Coupling impedance 50 O Insertion loss 0 3 dB or less Connector type N type connector rear side SMA connector inside USB Connector Item Specifications Wiring Straight connection Connector type B type receptacle rear side A type receptacle inside Mobile Phone Power UE_POWER Connector Item Specifications Maximum allowable voltage 5V Maximum allowable current 2A Connector type D sub 9 pin plug rear side D sub 9 pin receptacle inside This connector is used to supply power to the mobile phone or measure the consumption current 1M733062 01E Pin Assignments D sub 9 pin plug D sub 9 pin receptacle rear side inside the box Pin No Pin No 1 1l 2 2 a s 8 3 s 5 6l 8 l a sZ Ww Inside D Sub 9 pin receptacle Pin No Signal Name Specifications 2 ou WwW Power supply for the mobile phone Power supply for the mobile phone GND Reserved Reserved GND Power supply for the mobile phone Power supply for the mobile phone GND Reserved GND Connect to the positive electric potential of the mobile phone s battery terminal Connect to the negative electric potential of the mobile phone s battery terminal Do not connect anything Do not connect anything Connect to the positive electric potential of the mo
3. MC standards are specified in combination with the VC100 EMC standards VC200 VC3300 For details on the complying standards see the VC 100 VC200 VC3300 User s Manual External Dimensions Unit mm 288 5 278 8 3 len 356 8 Unless otherwise specified tolerance is 3 however tolerance is 50 3 mm when below 10 mm 10 1M733062 01E
4. Positioning block 1M733062 01E Handling Precautions General Handling Precautions Installation e e e Do not place objects other than the mobile phone inside the shield box Be sure to close the cover of the shield box Never place other instruments or objects containing water on top of the instrument otherwise a breakdown may occur Do not apply shock to the input output connectors To wipe off dirt on the case use a dry soft clean cloth Do not use volatile chemicals since this might cause discoloring and deformation When carrying the box close the lid and hold the handle on the side CAUTION The materials used inside the shield box may deform or alter when they come in contact with hot objects Installation Conditions Install the shield box in a place that meets the following conditions e Flat even surface Install the shield box with the correct orientation on a stable horizontal surface Ambient temperature 5 to 35 C Ambient humidity 20 to 80 RH no condensation Ve 7 1M733062 01E o Do Not Use in the Following Places In direct sunlight or near heat sources Where an excessive amount of soot steam dust or corrosive gas is present Near strong magnetic field sources Near high voltage eguipment or power lines Where the level of mechanical vibration is high Opening Closing the Lid Pull the front lever toward you to open the lid N CAUTION Befo
5. bile phone s battery terminal Connect to the negative electric potential of the mobile phone s battery terminal Do not connect anything Rear Side D Sub 9 pin plug Pin No Signal Name Specifications 2 oo o Power supply for the mobile phone Power supply for the mobile phone GND Reserved Reserved GND Power supply for the mobile phone Power supply for the mobile phone GND Reserved GND Connect to the positive electric potential of the mobile phone power supply Connect to the negative electric potential of the mobile phone power supply Do not connect anything Do not connect anything Connect to the positive electric potential of the mobile phone power supply Connect to the negative electric potential of the mobile phone power supply Do not connect anything IM733062 01E General Specifications Item Specifications Storage conditions Temperature 20 to 60 C Humidity 20 to 80 RH no condensation Operating conditions Temperature 5 to 35 C Humidity 20 to 80 RH no condensation Storage altitude 3000 m or less Operating altitude 2000 m or less External dimensions 280 W x 140 H x 320 D excluding the handle and projections Weight Approx 3 4 kg Installation position Horizontal Standard accessories RF cable N TNC 0 7 m 1 piece User s Manual 1 piece this manual Safety standards Safety and E
6. o i Model 733062 VC SHIELD Shield Box YOKOGAWA amp IM 733062 01E Yokogawa Electric Corporation 2nd Edition Introduction Thank you for purchasing the 733062 VC SHIELD Shield Box This user s manual contains useful information about the shield s functions and operating procedures and lists the handling precautions of the VC SHIELD To ensure correct use please read this manual thoroughly before beginning operation Checking the Contents of the Package In addition to the VC SHIELD the following standard accessories are included When you open the package make sure that all contents are present and undamaged If some of the contents are not correct or if any items are missing or damaged contact the dealer from whom you purchased them VC SHIELD Check that the MODEL given on the name plate on the rear panel is 733062 Standard Accessories RF cable N TNC type 1piece User s Manual 1piece B8014VC This manual IM733062 01E Conventions Used in This Manual Revisions 2nd Edition March 2006 YK damage to the instrument This symbol appears on the instrument to indicate that the user must refer to the user s manual for special instructions The same symbol appears in the corresponding place in the user s manual to identify those instructions In the manual the symbol is used in conjunction with the word WARNING or CAUTION WARNING Calls attention to actions or conditions that could cause serious o
7. r fatal injury to the user and precautions that can be taken to prevent such occurrences Improper handling or use can lead to injury to the user or CAUTION Calls attentions to actions or conditions that could cause E light injury to the user or damage to the instrument or user s data and precautions that can be taken to prevent such occurrences 1st Edition February 2006 2nd Edition March 2006 All Rights Reserved Copyright 2006 Yokogawa Electric Corporation 1M733062 01E Names of Parts Front Side Handle Lever used to open the lid Rear Side Name Plate SERIAL NO 85 2513 20 USB Connector Used when connecting the mobile phone installed inside the VC SHIELD to an external device via the USB UE POWER Connector Used to supply power to the mobile phone or measure the consumption current RF IN OUT Connector Connects the mobile phone tester and the shield box CABLE Used when connecting a cable to make measurements ANT Used when coupling antennas to make measurements Inside r RF IN OUT Connector Used when connecting a cable to make measurements Connects the mobile phone and the shield box USB Connector Used to connect the mobile phone and an external device via the USB UE POWER Connector Used to supply power to the mobile phone Mobile phone holder Slide lever Used to slide the mobile phone holder Slide position
8. re opening the lid remove objects placed on top of the lid The lid may fly open When opening the lid be careful not get in the way of the opening lid such as your face and hands When closing the lid be sure not to get your fingers caught between the lid and the box 1M733062 01E Connecting Cables Connecting the Mobile Phone Tester and VC SHIELD Connect the RF cable Part No B8014VC that comes with the shield box to the RF IN OUT connector CABLE or ANT on the rear side Connect the other end of the cable to the RF IN OUT connector on the mobile phone tester rear panel 1 If the RF IN OUT connector of the mobile phone tester is of type N purchase the following RF cable made by YOKOGAWA Model 739821 type N cable 1 m 2 When connecting a cable to make measurements Connect to CABLE When coupling antennas to make measurements Connect to ANT VC200 Spe Note When cables other than accessories or Yokogawa s specified RF cable are used specifications such as a shielding performance and the operating frequency range may not be achieved Connecting the Mobile Phone and VC SHIELD When connecting a cable to make measurements connect the RF IN OUT CABLE connector inside the shield box to the mobile phone with a coaxial cable The coaxial cable is to be provided by the user IM733062 01E Installing the Mobile Phone When coupling antennas to make measuremen
9. ts install the mobile phone by considering the relative positions of the antenna of the shield box and the built in antenna of the mobile phone 1 Press the mobile phone against positioning block 1 Positioning block 1 Cut at a slant to keep flip mobile phones from falling over lt Side View gt 2 To fix position of the mobile phone in place press the mobile phone against positioning block 2 Positioning block 2 lt Top View gt 3 Gently press the mobile phone against the nonslip rubber mat at the bottom to fix the mobile phone in place Positioning block 2 Positioning block 1 Moving the Mobile Phone Holder 4 When coupling antennas to make measurements in a reproducible fashion operate the slide lever in the direction of the arrows shown below and fix the position of the mobile phone to any position between slide position 1 and 4 Note The relationship between the slide positions of the mobile phone holder and the RF power loss by the antenna coupling vary depending on the mobile phone model and installation direction Compensation is possible by setting the RF loss compensation on YOKOGAWA s VC series testers 1M733062 01E Notes Concerning Measurements When coupling antennas to make measurements several dBs of error may result in the measured values due to the effects of coupling loss of the antenna and mobile phone If you wish to accurately
Download Pdf Manuals
Related Search