LABELMATE LLC MINI-CAT Universal Label Rewinder
Contents
1. the roll of labels you wish to unwind2. MAINTENANCE Your MC 10 requires no maintenance Product Limited Warranty All Labelmate Products are warranted to the original end user customer to be free from defects in materials and workmanship If it is determined by Labelmate that a product has failed under the terms of this warranty the product will be repaired or replaced at no charge to the customer Labelmate reserves all rights to determination of coverage and liability under this warranty The warranty period for all new Labelmate products is outlined below Warranty Period Products Covered Label Rewinders ayeas Label Unwinders Label Counters mechanical parts only Label Slitters mechanical parts only Label Dispensers Printer Mechanisms Power Supply Modules Counter modules Encoders Any products not specified above The warranty period for all products starts on the date purchased by the original end user customer Warranty coverage is not transferable with ownership and will terminate immediately upon rental resale or any other change in ownership This warranty does not cover repair to any product which is damaged has been modified is missing parts or has been opened or repaired by any unauthorised person Use of any unauthorised accessory or attachment will void coverage Purchase documentation should be retained for coverage verification In the event your product requires service please contact the distributor you bought the product from The cust
3. Rewind Shaft perpendicular to the web of the labels to be rewound and near where the labels come out of the printer The MC 10 is bi directional so can be operated in either direction Verify that the ON OFF ON Switch on the rear of the Unit is in the OFF 0 position Set the VOLT CHANGE SW Slide Switch on the AC DC Adapter to the 4 5 position as an initial setting Insert the Power Cord into the Power Jack on the rear of the MC 10 Plug the AC DC Adapter into a suitable electrical outlet It can be left plugged in at all times The MC 10 has a combination Power and Direction ON OFF ON Direction Switch on the Rear Panel See photo below The Centre Position of the Switch is OFF 0 To make the Rewinder run to the right looking from the rear of the Rewinder press the Power Direction Switch in the direction of the right arrow To make the Rewinder run to the left press the Power Direction Switch in the direction of the left arrow REWINDING LABELS Rewind Directly On Shaft coreless 1 Slide the hook shaped metal Bail onto the MC 10 Shaft The straight end goes into the hole in the plastic Flange Plate The curved end fits into the small hole in the outer end of the Shaft Insert the label web under the Bail and turn the Rewind Shaft by hand to secure the labels Place the MC 10 ON OFF ON Direction Switch to the ON position in the desired direction of operation left or right Start th
4. e Printer and observe that the labels are being rewound correctly You can adjust the VOLT CHANGE SW Slide Switch on the Power Supply Module to provide more or less rewind force When rewinding is finished place the MC 10 ON OFF ON Switch in the OFF 0 position To remove the labels first pull out the hook shaped Bail from the center of the label roll Then remove the labels Rewind on a Cardboard Core 1 To use a cardboard core install the 3 stainless steel Fins onto the Rewind Shaft of the MC 10 using the 6 screws provided The curved sides of the Fins face the Shaft For narrow cores orient the Fins next to the plastic Flange Slide an empty cardboard core over the Fins and up against the plastic Flange Plate Use a piece of masking tape to secure the label web to the cardboard Place the MC 10 ON OFF ON Direction Switch to the ON position in the desired direction of operation left or right Start the printer and observe that the labels are being rewound correctly You can adjust the VOLT CHANGE SW Slide Switch on the Power Supply Module to provide more or less rewind torque When rewinding is finished place the MC 10 ON OFF ON Direction Switch in the OFF 0 position Slide the cardboard core and the labels off the MC 10 UNWIND FEATURE To use the MC 10 as an Unwinder place the VOLT CHANGE SW to the 1 5 position and place the ON OFF ON Direction Switch in the reverse direction to provide resistance to
5. omer assumes responsibility for all cost and risk incurred in transport for service Labelmate makes no other warranty of any kind expressed or implied or to suitability or fitness for a particular purpose No other person agent or reseller is authorised to give any warranties on behalf of Labelmate Any obligation to warranty other than that specifically addressed above is hereby disclaimed LABELMATE LLC 69 AVENUE ALPHONSE XIII 1180 BRUSSELS BELGIUM TEL 322 375 69 60 FAX 322 375 38 96 brussels labelmate com www labelmate com LABELMATE User_MC 10 02 07 MC 10 MINI CAT Universal Label Rewinder Switched Bi Directional Control e Constant Adjustable Torque CAT Technology Remove all parts from the shipping container and verify contents Package Contents e User Manual this document e MC 10 Rewinder Unit e Shaft Assembly with Flange and Bail e Plastic Bag with 3 metal Vanes 6 Screws for the Vanes e Power Supply Module Retain the Shipping Container and Packaging for Storage and Transport e KEEP MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE e SPECIFICATIONS Max Label Roll Weight 3Kg 6 6Lb Max Label Roll Size 220mm 8 7 Start Stop ON OFF ON Direction Switch Power Supply Input 220 240VAC 50 60Hz Output Selectable 1 5VDC to 12VDC A WARNING This Product is for indoor use only Not for use in wet locations SET UP 1 Place the MC 10 with the
Download Pdf Manuals
Related Search