User Manual
Contents
1. machine parts are cleaned as soon as the work is finished 98148 US 3 3 07 2012 AA www santos fr MAINTENANCE e Put the appliance to the Off position with the On Off button 11 and unplug the power supply lead plug 10 e Remove the large diameter ram 5 or the reducer 6 and the small diameter ram 7 e Unclip the locking loop 3 from the clip 4 pulling it towards you e Raise the guide channel 2 For cleaning after handling products which are difficult to clean products with greasy substances for example the guide channel hinge pin 8 can be removed and the guide channel washed in a dish washer e Take the disk 13 14 off the motor spindle 18 e Take the ejector 12 off the motor spindle 18 e Wash with dish washing detergent then rinse and dry the grater disk 13 or the slicer disk 14 the guide channel 2 and the dirt tray 9 e Clean the base 1 with a soft damp sponge and dry Fitting the cutting tool FITTING e Fit the ejector 12 smooth side on the disk side onto the end of the motor shaft 18 line the grooves up with the pins 15 and push to the motor shaft stop 18 e Fit the grater disk 13 or the slicer disk 14 lining up the drive pin with the groove in the disk support 13 or 14 REMOVING e Pull the grater holder disk or the slicer disk upwards and along the motor shaft 18 axis be careful risk of cuts on holding the tool especially for the slicing disks as the2. from the motor spindle 18 and wash it in fresh water 4 Wash all the items in contact with food in fresh water the guide channel 2 the dirt tray 9 the large diameter ram 5 the reducer 6 the small diameter ram 7 the slicer disk 14 and the grater disk 13 TAKE CARE RISK OF CUTS ON HANDLING THE KNIVES STARTING UP 1 After selecting the appropriate tool for the work required grating or slicing fit the ejector 12 smooth side on the disk side and the disk 13 onto the motor spindle 18 Close the guide channel 2 Place a recipient under the appliance outlet Lock the guide channel 2 with the locking loop 3 and position on the clip 4 Plug the power supply plug 10 into your mains power socket Switch the machine on by putting the On Off switch 11 to the 1 position the indicator lights up Introduce the products into the guide channel 2 or into the reducer 6 Push the products in using the large diameter ram 5 or the reducer 6 and the small diameter ram 7 until the ram reaches the collar oo k o N CLEANING IMPORTANT e Stop the machine and unplug the machine power supply lead e The appliance must not be cleaned either with a water spray or pressure jet nor should it be immersed For easier cleaning do not allow food to dry on the guide channel 2 the grater disk 13 the slicer disk 14 the ejector 12 or the dirt tray 9 It is recommended that all these
3. CATE WARRANTY Since the 01 01 95 all our appliances comply with CE and possess the CE label Our guarantee is of 24 months from the manufacturing date mentioned on the descriptive plate except concerning the asynchronous motors consisting of a rotor and a stator which are warranted for 5 years from their manufacturing date Warranty is strictly limited to the free replacement of any part of origin recognized by us as defective due to a defect or building default and identified as belonging to the concerned appliance Warranty does not apply to damages resulting from installation or use non complying with our appliance data sheet user s manual or in case of an evident lack of maintenance or disrespect of elementary security electric rules It does not apply in case of regular wear and tear Any replacement of parts under warranty will be realized after return of the defective part in our workshops postage paid supported by a copy of a conformity statement on which appears the serial number of the appliance Every appliance is equipped with a descriptive plate conforming to the EC recommendations and of which a duplicate exists in the conformity statement serial number manufacturing date electrical characteristics In case of serious damage judged repairable only in our workshops and after prior consent from our departments any appliance under guarantee is sent by the Distributor carriage paid In case of repairs or reconditioning of app
4. SANTOS SAS 140 150 AVENUE ROGER SALENGRO 69120 VAULX EN VELIN LYON FRANCE o TEL 33 0 472 37 35 29 FAX 33 0 478 26 58 21 A ANTOS E Mail santos santos fr www santos fr VEGETABLE SLICER NO 48 CHEESE GRATER No 49 USER AND MAINTENANCE MANUAL IMPORTANT documents included in this manual to be kept e CE COMPLIANCE DECLARATION e WARRANTY CERTIFICATE Translation of the original version Coffee grinders Fruit juicers Mixers Blenders Drinks dispensers Planetary mixers Dough mixers Cheese graters Ice crushers Mincers Vegetable slicers INTERNATIONALLY PATENTED MODELS 98148 US 3 3 07 2012 AA www santos fr CONTENTS CE COMPLIANCE DECLARATION EE 3 VEGETABLE SLICER No 48 CHEESE GRATER No A0 4 EQUIPMENT AND ACCESSORIES sma AKING KG NA NGANGA 4 PUNY eset bese arene tects nee AA AA NANA 4 RE 4 Disk Storage aa AA AA AND ANA 5 RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE u 111111 1a 5 WARNING es maa ch sareenesuaeseae na ATE Erreur Signet non defini ELECTRICAL CONNECTION KEE 6 USING THE EEN 7 USING FOR THE 18 TIME 2 NBA ANAN GN EANn mmm 7 STARTING UP EE 7 ENEE 7 MAINTENANCE EE 8 Fitting GHEET striven Peete eee 8 ENEE 8 Safety device housing closure AEN 8 Safety device motor overload E 8 Safety device motor overheatng ee 9 Safety device access to rotating tools cceeeeeeeeeeeeeeeeeeeeneeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 9 MAINTENANGF eieiei 9 Spare 8G e
5. e recycling symbol marking relating to waste electrical and electronic equipment This means that this product must be processed by a waste sorting system in accordance with Directive 2002 96 CE WEEE Professional Equipment section so that it can be either recycled or disassembled in order to reduce any impact on the environment For further information please contact your dealer or SANTOS For the elimination or recycling of the appliance components please contact a specialist company or contact SANTOS Electronic products which have not been out sorted are potentially dangerous for the environment The packaging materials must be eliminated or recycled in accordance with regulations in force IMPROPER USE 1 The appliance No 48 49 is not designed to be used with knives of a cut of 10 mm or more 2 The appliance should neither be cleaned in a jet of water nor with a high pressure spray 3 The base 1 must not be immersed in water 4 For electrocution risk protection reasons never plunge the base into water or any other liquid 5 Unplug the appliance before carrying out any work on it cleaning maintenance or repair The use of spare parts other than certified SANTOS original parts is prohibited This appliance is not designed for use by people including children whose physical sensorial or mental capacities are impaired or by people with no experience or knowledge unless they have been supervised or given traini
6. egene 9 STANDARD DEELER 10 MACHINE TECHNICAL SPECIFICATIONS ccccceeeeeeeeeeeeeeeeeeeeeeeeeaeeeeeseeeeeeeeeeeaes 10 110 120 V 50 60 Hz electrical wiring diagram EE 11 220 240 V 50 60 Hz electrical wiring dagram EE 12 WARRANTY CERTIFICATE iiss ssnscsisassisdinsaniadscndeassusadivanisnisnnvisiedaiabiindconsienndeddalstmnunesansdebusiens 14 APPLIANCE IDENTIFICATION PLATE samaan aNG ANNA ANAN 14 98148 US 3 3 07 2012 R 3 www santos fr CE COMPLIANCE DECLARATION THE MANUFACTURER SANTOS sas 140 150 Av Roger SALENGRO 69120 VAULX EN VELIN LYON FRANCE declares that the appliance intended for the professional market described below Description VEGETABLE SLICER CHEESE GRATER Type number 48 49 complies with e the statutory provisions defined in appendix 1 of the European machines directive n 2006 42 CE and the national legislation transposing it e the statutory provisions of the following European directives and regulations o N 2006 95 CE low voltage directive N 2004 108 CE EMC directive No 2002 95 CE RoHS directive No 2002 96 CE WEEE directive N 1935 2004 CE regulation relating to materials and articles intended to come into contact with foodstuffs O O O O Harmonised European standards used to give presumption of conformity with the essential requirements of the above mentioned directives e NF EN 1678 A1 2010 Food processing machinery Vegetable cutting machines Safety a
7. hile operating safety is provided by the following three points 1 The motor can only be started if the guide channel 2 is in position and locked by the locking loop 3 2 The guide channel provides safety on the input side for the products to be processed The dimensions of the introduction guide channel 2 comply with the standard safety requirements currently in force 3 The restriction system formed by the guide channel 2 and the ejector 12 provides the safety on the output side of the products processed MAINTENANCE Before any work on the appliance it is imperative that the machine is disconnected from the mains 10 Spare parts This machine requires no specific maintenance The bearings are lubricated for life If work is required to replace wear parts such as the electrical components or other refer to the parts list see exploded view at the end of the manual For all spare part orders see references in the exploded view at the end of the manual state gt the type gt the machine serial number and gt the electrical specifications recorded under the machine 98148 US 3 3 07 2012 R 3 www santos fr STANDARD REFERENCES CE Europe GS Germany controlled by the LNE National Test Laboratory UL USA and cUL Canada NSF USA MACHINE TECHNICAL SPECIFICATIONS ELECTRICAL SPECIFICATIONS 1 Model no 48 Single phase Power supply voltage 220 240 100 120 Frequenc 50 60 50 60 Motor rati
8. knife blades are very sharp e Pull the ejector 12 upwards and along the motor shaft 18 axis making sure it passes correctly level with the tool drive pin 15 on the motor shaft 18 SAFETY Safety device housing closure 1 The guide channel 2 must be in the closed position and the locking loop 3 in the locked position on the clip 4 to provide mechanical unlocking of the motor and allow the slicer to be turned on with the On Off switch 11 2 Unclipping the locking loop 3 causes stoppage position 0 on the switch 11 and mechanical stoppage of the motor spindle 18 3 A cut in the mains power supply causes stoppage position 0 on the switch 11 The switch 11 has to be reactivated position 1 to start again Safety device motor overload Turn the power off unplug the mains lead plug 10 before any work 98148 US 3 3 07 2012 an www santos fr If the motor is jammed 17 foreign body too hard body too much pressure on the processed products etc the switch 11 automatically goes to the O position Rectify the problem and then press the switch 11 to position 1 Safety device motor overheating Turn the power off unplug the mains lead plug 10 before any work If the motor overheats the switch 11 automatically switches to the O position Wait for the motor to cool down 15 to 30 minutes and then press the switch 11 to position 1 Safety device access to rotating tools Tool access w
9. liances not under guarantee the round trip transport is payable by the distributor The parts and workforce are invoiced at the current rate A preliminary estimate can be supplied Coffee grinder not using SANTOS original burrs are not taken under guarantee The warranty conditions repairs reconditioning of the espresso coffee grinder are the object of a specific note Our guarantee does not extend to the payment of penalties the repair of direct or indirect damages and notably to any loss of income resulting from the nonconformity or the defectiveness of products SANTOS s global responsibility being limited to the sale price of the delivered product and to the possible repair of the defective products In case of revelation of an imperfection during the warranty period the Distributor has to unless a different written agreement of SANTOS indicate to his customer to stop any use of the defective product Such a use would release SANTOS of any responsibility APPLIANCE IDENTIFICATION PLATE SPECIMEN For all documents not supplied with l the appliance l i I l Printed Faxed and Downloaded 98148 US 3 3 07 2012 A www santos fr
10. nd hygiene requirements This European standard is a type C standard as defined in EN ISO 12100 When the provisions of this type C standard differ from those stated in the type A or B standards the provisions of the type C standard override the provisions of the other standards This standard provides the means to comply with the requirements of the Machines directive n 2006 42 CE see appendix ZA e NEEN ISO 12100 1 and 2 2004 Safety of machinery General principles for design e NF EN 60204 1 2006 Safety of machinery Electrical equipment of machines General requirements e NF EN 1672 2 2005 Food processing machinery Basic concepts Hygiene requirements e NF EN 60335 1 2003 Household and similar electrical appliances Safety e NF EN 60335 2 64 2004 Particular requirements for commercial electric kitchen machines Drawn up in VAULX EN VELIN on 01 12 2010 Signatory s position CHIEF EXECUTIVE OFFICER Signatory s name Aur lien FOUQUET A Signature 98148 US 3 3 07 2012 an www santos fr VEGETABLE SLICER No 48 CHEESE GRATER No 49 The No 48 vegetable slicer is of sturdy construction component parts in cast aluminum rubber and food quality plastic and is particularly suitable for cutting slicing thinly slicing grating and stripping in preparations made by professionals in Restaurants Pizzerias Snack bars Catering points sandwich bars theme restaurants etc With its powerful mot
11. ng Input power 0 39 0 45 Speed 1000 1200 Running capacitor 10 uF 400V 20uF 400V Height under the ram Dimensions Height with ram Width Depth Net weight Packaged weight 1 These values are given as an indication only The exact electrical specifications for your machine are recorded on the identification plate 2 Noise level measured in acoustic pressure with the machine under load at 1 m from its axis in accordance with standard EN 31201 98148 US 3 3 07 2012 dh www santos fr 110 120 V 50 60 Hz electrical wiring diagram Brown Black 20 uF capacitor White On Off Brown o Guide channel safety device i Green gt NS 98148 US 3 3 07 2012 Ah www santos fr 220 240 V 50 60 Hz electrical wiring diagram Brown Black 10 uF capacitor White On Off Guide channel safety device Green Yellow kag a EEN 98148 US 3 3 07 2012 R 3 www santos fr QS santos d EF Description Base Guide channel Locking loop Clip Large diameter ram Reducer Small diameter ram Guide channel hinge pin 9 Dirt tray 10 Power supply lead 11 On Off switch on a co po N 12 Ejector 13 Grater disk 14 Slicer disk 15 Drive pin 16 __ Identification plate 17 Motor 18 Motor shaft 98148 US 3 3 07 2012 www santos fr ES santos WARRANTY CERTIFI
12. ng in the use of the appliance beforehand by a person responsible for their safety Supervise children to ensure they do not play with the appliance NO Note To make understanding the following paragraphs easier please refer to the diagrams at the end of this manual 98148 US 3 3 07 2012 an www santos fr ELECTRICAL CONNECTION e The electric power supply for the machine is available in 2 single phase voltages 110 120 V 50 60 Hz model 48V1 and 49V1 220 240 V 50 60 Hz model 48 and 49 Line protection the machine should be connected to a standard 2 pole earth electric socket The system should be fitted with a ground fault circuit interrupter and a fuse rated at 16A The appliance must be earthed CARE e Before connecting the machine check that the mains electrical voltage is the same as the voltage for your machine This value is given gt either on the identification plate under the machine gt or on the identification plate on the last page of this manual e f the power supply lead is damaged it must be by a special assembly available from approved SANTOS dealers or from SANTOS CARE Check that the On Off switch 11 is in the 0 position before connecting the power supply lead plug to your mains electric power socket 98148 US 3 3 07 2012 an www santos fr USING THE MACHINE USING FOR THE 1 TIME 1 Unclip the locking loop 3 2 Open the guide channel 2 3 Remove the ejector 12
13. or it can drive either high output cutting disks or grating disks of 170 mm The active part of the tools knives for slicers or disks for grating disks is made of stainless steel Care the appliance is designed for cutting slicing stripping and grating all types of vegetable fruits cheeses and sausages but not frozen foods EQUIPMENT AND ACCESSORIES Rams A ram 5 for large diameter of between 70 mm and 40 mm products such as potatoes turnips apples Gruyere and Parmesan cheese etc A reducer 6 and a small diameter ram 7 for long and small diameter maximum diameter 40 mm products such as carrots cucumbers courgettes etc Disks 48200T1 1 mm cut slicer disk 48200T2 2 mm cut slicer disk 48200T3 3 mm cut slicer disk 48200T4 4 mm cut slicer disk 48200T5 5 mm cut slicer disk 48200T6 6 mm cut slicer disk 48200TD4 4 mm special Tomatoes slicer disks 48200TD6 6 mm special Tomatoes slicer disks 48200TO4 4 mm special Crinkle cut potatoes slicer disks 48200R2 O 2 mm grater disk 48200R3 O 3 mm grater disk 48200R4 4 mm grater disk 48200RP Parmesan cheese grater disk 48200RR Rostis grater disk 48200E2 2x2 stripping disk 48200E4 4x4 stripping disk 48200E8 8x8 stripping disk chips 98148 US 3 3 07 2012 AA www santos fr Disk storage 48290 Disk support for work surfaces or for wall application optional RECYCLING THE PRODUCT AT THE END OF ITS SERVICE LIFE This appliance has th
Download Pdf Manuals
Related Search