Product Manual
Contents
1. PLANAR PE1 1 User s Manual Table of Contents Chapter I Installation Unpacking Connecting the LCD Monitor and Base Viewing Angle Adjustment Detaching LCD Monitor from Its Stand Interface for Arm Applications Connecting the Display Connecting the AC Power Setting Up the LCD Monitor Power Management System Chapter 2 Display Controls User Controls Adjusting the Monitor s Display Function Description Chapter 3 Technical Information Specifications Standard Timing Table Troubleshooting Preface This manual is designed to assist users in setting up and using the LCD Monitor Information in this document has been carefully checked for accuracy however no guarantee is given to the correctness of the contents The information in this document is subject to change without notice This document contains proprietary information protected by copyright All rights are reserved No part of this manual may be reproduced by any mechanical electronic or other means in any form without prior written permission of the manufacturer FCC Statement Warning This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructio2. 12 3 Figure 2 1 DC Power Switch Press the power switch to switch the monitor ON OFF DCP On LED lights Green color Power is ON Indi oa e LED lights Yellow Monitor is in Power Saving Mode e LED is off Power is OFF Function Select Press either left or right control button for OSD On Screen Display Buttons menu selection Adjustment Control Press the left button to decrease the OSD setting and press the right Buttons button to increase the OSD setting Adjusting the Monitor s Display The monitor has four function control buttons to select among functions shown on OSD menu designed for easy user viewing environments OSD Function Menu To access OSD Main menu simply press one of the Function Select control buttons and the menu diagram will pop up on the screen as shown on Fig 2 2 Continue pressing the Function Select buttons to scroll through the entire menu items then press Adjustment Control buttons to adjust content of selected item i200 407 a eer T Figure 2 2 Attention Firmware revision may have been updated into a latest version while the version number shown on all OSD menus in this manual will stay as Ver 1 00 Function Description Function Description Brightness 101 scales of brightness are available to choose from 0 to 100 101 scales of contrast are available to choose from 0 to 100 Digital Input Contrast Mode not support This function let s you adjust the displa
3. 0 K 6500 CIE coordinated Color Temperature of 6500 K Sets the CIE coordinate color temperature to 6500 K U Three colors Red Green Blue can be Sets the settings to a by user defined CIE Temperature ner adjusted from the OSD menu Auto and Input Select Chapter 3 Technical Information Specifications LCD Panel AU Hydis Size 17 43 cm 17 43 cm Display Type Active matrix color TFT LCD Active matrix color TFT LCD Resolution 1280 x 1024 1280 x 1024 Display Dot 1280 x RGB x 1024 1280 x RGB x 1024 Display Area mm 337 92 x 270 336 H x V 337 92 x 270 336 H x V Display Color 262K 262K Brightness 260 cd m typical 250 cd m typical Contrast Ratio Response Time 400 1 typical Ta 25 C Tr Tf 16ms 430 1 typical Ta 25 C Tr Tf 20ms Lamp Voltage 700 Vrms typical 705 Vrms typical Lamp Current 7 0 mA rms typical 6 5 mA rms typical Viewing Angle Vertical 70 70 Vertical 65 65 Horizontal 70 70 Horizontal 80 80 Display Colors 16 7M with FRC or Dithering Video Input Signal Analog RGB 0 7Vp p Digital TMDS Input Impedance 75 Ohm 2 Polarity Positive Negative Amplitude 0 0 7 0 05 Vp Multi mode Supported Horizontal Frequency 24 80 KHz Vertical Frequency 56 75 Hz Control Power switch On Off switch with LED indicator hard and soft types OSD Brightness Digital Contrast Digital Horizontal Position Digital Vertical Position Digital Phase Di
4. ck to the normal PC operating environment gt If there s no picture on the LCD Monitor please perform the following steps 1 Make sure the power indicator on the LCD Monitor is ON all connections are secured and the system is running on the correct timing Refer to Chapter 3 for information on timing 2 Turn off the LCD Monitor and then turn it back on again If there is still no picture press the Adjustment Control button several times 3 Ifstep 2 doesn t work connect your PC system to another external CRT If your PC system Functions properly with a CRT Monitor but it does not function with the LCD Monitor the output timing of the VGA card may be out of the LCD s synchronous range Please change to an alternative mode listed in the Standard Timing Table or replace the VGA card and then repeat steps 1 and 2 If you have chosen an output timing that is outside of the LCD Monitor s synchronous range Horizontal 24 80 KHz and Vertical 56 75 Hz the OSD will display a Out of Range message Choose a mode that is supported by your LCD Monitor Also if the signal cable is not connected to LCD monitor at all or properly the monitor screen will display a message No Input Signal
5. computer es 2 Connect one end of the signal cable to the LCD Monitor s TT T VGA port or DVI port See Fig 1 5 3 Connect the other end of the signal cable to the VGA port or amp athe DVI port on your PC 4 Make sure connection are secure Figure 1 5 Attention This device must be connected to an off the shelf video cable in order to comply with FCC regulations A ferrite core interface cable is included in the LCD Monitor package This device will not be in compliance with FCC regulations when a non ferrite core video cable is used Connecting the AC Power EEE 1 Connect the power cord to the LCD Monitor See Fig 1 6 ai 2 Connect the power cord to an AC power source t a a Figure 1 6 E Setting Up the LCD Monitor TENE 1 Turn on the LCD monitor s hard power switch located on the back of the monitor _ i Li 2 Turn on the LCD Monitor s soft power switch located on TF the bezel of the monitor l j i i Figure 1 7 Power Management System This LCD Monitor complies with the VESA DPMS version 1 0 Power Management guidelines The VESA DPMS provides four power saving modes through detecting a horizontal or vertical sync signal When the LCD Monitor is in power saving mode the monitor screen will be blank and the power LED indicator will light yellow Chapter 2 Display Controls User Controls A brief description and the location of all LCD Monitor function controls and indicators
6. e timing H Freq V Freq Pixel Freq H V Sync Mode KHz Hz MHz Polarity Note I When the in put display mode is not 1280 x 1024 the image is smoothly expanded to 1280 x 1024 dots with the gm5120 scaling engine After expansion from 650x350 640x400 640x480 720x400 832x624 800x600 and 1024x768 resolution the text may look not so sharp and the Graphics may look not so proportional 2 640x400 56Hz and 1024x768 66Hz modes cannot be supported when Digital TMDS input Troubleshooting This LCD Monitor has pre adjusted using factory standard VGA timings Due to the output timing differences among various VGA cards in the market users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected Attention This LCD Monitor Supports Multiple VGA Modes Refer to the Standard Timing Table for a listing of modes supported by this LCD Monitor Resolution The picture is unclear and unstable please perform the following steps 1 Enter PC to Shut Down Windows status while you re in MS Windows environment 2 Check the screen to see if there s any black vertical stripes appear If there are take advantage of the Clock function in OSD menu and adjust by increment or decrement numbers until those bars disappear 3 Move to Phase function in OSD menu again and adjust the monitor screen to its most clear display Click No on Shut Down Windows and ba
7. gital Clock Digital Display Mode Setup Use EEPROM to save settings in memory OSD Format 20 characters x 9 rows Power Management Mode Power Consumption AC Input LED Color 240 VAC 240 VAC Soft switch off 3W maximum 240 VAC Dark Disconnected 3W maximum Dark o O Yellow Standby Suspend Off 240 VAC Dark DC Power off l 1W maximum 120 VAC Meeting VESA DPMS requirements measured from AC Input end of AC power cord 6 Sync Input Signal Separate TTL compatible horizontal and vertical synchronization Digital TMDS Polarity Positive and negative Plug amp Play Supports VESA DDC2B functions External Connection Power Input AC input AC socket Video Cable 1 8M with 15 pin D sub connector 1 8M with 24 pin DVI D Environment Operating Condition Temperature 5 C to 40 C 41 F to 104 F Relative 20 to 80 Storage Condition Temperature 20 C to 60 C 4 F to140 F Relative 5 to 85 Power Supply AC Input Input Voltage Single phase 100 240VAC 50 60 Hz Input Current 1 2 A maximum Size and Weight Dimensions 374 W x 394 5 H x 204 D mm Net Weight 5 0 3 kg Gross Weight 70 3 kg Pin Assignment 5V Red Green Hot Plug Detect Blue NC Digital GND SDA Digital GND H Sync Red Rtn V Sync Green Rtn SCL Blue Rtn E For Digital DVI D connector Standard Timing Table If the selected timing is NOT included in table below this LCD monitor will use the most suitable availabl
8. n may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and the receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Warning Use only shielded signal cables to connect I O devices to this equipment You are cautioned that changes or modifications not expressly approved by the party responsible for comliance could void your authority to operate the equipment Canadian DOC Notice ps This Class B digital apparatus meets all requirements of the Canadian Interference Causing Ha Equipment Regulations Cet appareil num rique de la classe B repecte toutes les exigences du R glement sur le mat riel brouilleur du Canada Important Safety Instructions Please read the following instructions carefully This manual should be retained for future use 1 To clean LCD Monitor screen Power off LCD Monitor and unplug the AC Cord Spray a non solvent cleaning solution onto a rag Gentl
9. or make sure that the following items were included in the box LCD Monitor User s Manual 1 8M Monitor to PC VGA Cable 1 8M Power Cord 1 8M Monitor to PC DVI D Cable Base If you find that any of these items is missing or appears damaged contact your dealer immediately Connecting the LCD Monitor and Base When you open the box to take the base and put on the desk first Then connect the LCD Monitor and base please See fig 1 1 Figure 1 1 Viewing Angle Adjustment The LCD Monitor is designed to allow users to have a comfortable viewing angle The viewing angle can be adjusted from 5 to 30 See fig 1 2 Figure 1 2 Warning Do not force the LCD Monitor over its maximum viewing angle settings as stated above Attempting this will result in damaging the Monitor and Monitor stand Detaching LCD Monitor from Its Stand T Unscrew screws the swivel base support column and pull down the hinge to release Figure 1 3 Interface for Arm Applications Before installing to mounting device please refer to Fig 1 3 ra The rear of this LCD display has four integrated 4 mm 0 7 Cit ai j pitches threaded nuts as well as four 5 mm access holes in the Hee a plastic covering as illustrated in Figure 1 4 These EF specifications meet the VESA Flat Panel Monitor Physical a Mounting Interface Standard paragraphs 2 1 and 2 1 3 Figure 1 4 version 1 dated 13 November 1997 e Connecting the Display Frrerrrr 1 Power off your
10. window horizontally KI OSD V Position This function moves the OSD menu window vertically Because the H and V Frequencies of both 640 x 400 70Hz and 720 x 400 Graph Text 70Hz are the same this function let s you manually select either 640 x 400 graphics mode or 720 x 400 text mode Digital Input Mode not support i Recall si The recall function will return all adjusted parameters to factory preset values Five OSD language options are available English German French Spanish Language and Italian Press the left or right adjustment control button to select other l lan amp Press button E to activate the selected function Auto Adjustment not support in Digital Input Mode Use Analog Input or Use Digital Input The Auto Adjustment function let you adjust the display size clock and phase to obtain the best viewing settings This process will take 3 5 seconds to complete Attention After Auto Adjustment the display might display wrong position or size if it has received a pattern which has no screen border You may select either Analog or Digital Input video when VGA input or and DVI Input is are available E OOO t Saves the values of this setting and exits the OSD menu function Icon Function Description 9300 CIE coordinated Color Temperature of 9300 K Sets the CIE coordinate color temperature to 9300 K 7500 CIE coordinated Color Temperature of 7500 K Sets the CIE coordinate color temperature to 750
11. y clean the screen with dampened rag 2 Do not place the LCD Monitor near a window Exposing the monitor to rain water moisture or sunlight can severely damage it 3 Do not apply pressure to the LCD screen Excess pressure may cause permanent damage to the display 4 Do not remove the cover or attempt to service this unit by yourself Servicing of any nature should be performed by an authorized technician 5 Store LCD Monitor in a room with a room temperature of 20 60 C or 4 140 F Storing the LCD Monitor outside this range could result in permanent damage 6 If any of the following occurs immediately unplug your monitor and call an authorized technician Monitor to PC signal cable is frayed or damaged Liquid spilled into LCD Monitor or the monitor has been exposed to rain LCD Monitor or the case is damaged 7 A certified line is required to connect this device to a power outlet For a nominal current up to 6A and a device weight above 3 kg a line not lighter than HOSVV F 3G 0 75 mm must be used Chapter I Installation Unpacking Before unpacking the LCD Monitor prepare a suitable workspace for your Monitor and computer You need a stable and clean surface near a wall power outlet Make sure that LCD Monitor has enough space around it for sufficient airflow Though the LCD Monitor uses very little power some ventilation is needed to ensure that the Monitor does not become too hot After you unpack the LCD Monit
12. y s horizontal position Digital Input Mode not support V Position This function let s you adjust the display s vertical position Digital Input Mode not support This function let s you select the images sharpness Five selections are Sharpness available A smoother setting is more suitable for pictures while a sharper setting 1s more suitable for text Digital Input Mode not support H Position 080 Transpareney This function let s you set the transparency of the OSD menu The OSD Transparency transparency is adjustable from 0 to 100 11 scales are available Digital Input Mode not support Phase A total of 256 scales 0 to 255 are available to adjust the focus and clarity of the display Digital Input Mode not support This function carries a frequency tracking feature that offers users better stability and clarity 101 scales from 50 to 50 are available on the mode that is currently running The adjustable range can be variable in different modes This function records the deviated number of clock period between input timing and supported timing The clock value may not be 0 after Auto Adjustment when the input timing is different from supported timing Digital Input Mode not support Color T t Push the Eh button to select a different color temperature Please see the i a ca diagram below for function and description Digital Input Mode not support ry OSD H Position This function moves the OSD menu
Download Pdf Manuals
Related Search