ZRC-100 Quick Setup Guide
Contents
1. 100 provides a useful function which is Re scan Devices that allows rediscovering all Z Wave devices from the network Please refer to user manual with below steps 1 Assume all Z Wave devices have been added by gateway 11 ZRC 100 should act as a secondary controller step of B11 1 iii Execute the Re scan Devices function step of C3 ZRC 100 will rediscover Z Wave devices from the network discovered devices will be re assigned to their default categories Devices Comforts and Sensors and names will be re assigned with default naming in ascending order A This action may take up to 0 5 1 hour depends on how many devices are in your network and it will wipe out all previously stored device names Please make sure batteries are full before proceed iv Now all Z Wave devices will appear on the Device Comfort and Sensor categories You can rename your device individually if needed Printed in China F820 8380 0000 O2. z gt gt gt gt Press the program button Add Device on the target device E Press PROG on target z gt gt gt gt y Add Device Press PROG on target z gt gt gt gt included in another Z Wave network In this case please delete this device following the steps in the Deleting Device from the Network section then add this device again If you can t add your Z Wave device this device might have been Step 3 After adding devices to your ZRC 100 you can turn the device using the corresponding Device Control function Setup Key LCD Indication Select Device and Tn press key to Scene gt confirm Comfort gt A corresponding Device Control page will be displayed OK to Enter Devices List Switch 001 lt Off and On gt For on off switches press key to turn on the device and lt key to turn off the device To operate dimmer and motorized curtain Press and hold the gt key until reach to your desired level and release the key to open the curtain or to increase the dimmer intensity Press and hold the 4 key until reach to your desired level and release the key to retract the curtain or to reduce the dimmer intensity Devices List Switch 001 Dimmer 002 lt Off and On gt Devices List Switch 001 Dimmer 002 lt Off and On gt Note 1 The screen will display LOCK UNLK if this is a secured door lock device Note 2 You can ren
3. BACK key for 2 seconds to go back to root menu Add Device B2 Delete Device B3 Add to Scene B4 Select Scene B4 1 a Select Scene B5 1 Device Config B6 Device Configure B6 1 Comfort Configure B8 1 Sensor Configure B9 1 Shortcut Key B10 Shortcut Key B10 1 Advanced Setup B11 Learning Mode B11 1 Config Assoc B11 2 Configuration B11 3 Reset to Default B11 4 System Settings B12 LCD Contrast B12 1 B L Brightness B12 2 Sleep Timer B12 3 About B13 24 Press and hold 4 w keys simultaneously for 3 seconds to enter Network Setup menu Press BACK key to go back to previous page Press and hold BACK key for 2 seconds to go back to root menu Network Setup C1 Rediscover N W C2 Rediscover network Re scan Devices C3 Delete Dead Node C4 Listening Mode C5 Create Sec C6 Create secondarv Create Pri C7 Create primary QUICK SETUP STEPS EXAMPLE Step 1 Connect a Z Wave device for example a light switch to power supply Setup Key LCD Indication Press and hold lt 4 gt keys simultaneously for 3 seconds under the Home Scene gt Comfort gt OK to Enter i Setup E Add Device gt Delete Device gt Add to Scene gt OK to Enter Select Add Device Setup Add Device gt Delete Device gt Add to Scene gt OK to Enter Add Device Press a key to add Press PROG on target the device into Z Wave network
4. ZRC 100 Quick Setup Guide The ZRC 100 is a portable Z Wave remote controller with multi channel support It can be configured as a primary or secondary controller within a Z Wave home automation network It works with almost every Z Wave enabled devices binary switches dimmers thermostats secured door locks binary or multi level sensors Users can control their Z Wave enabled devices individually or through Scene control Scene is a collection of Z Wave devices configured to a user preferred settings levels modes or operating conditions The ZRC 100 also equipped with a backlit LCD screen and an intelligent Self Navigated Button SNB system Users can setup and operate their Z Wave devices through the LCD and the SNB system using their ZRC 100 and enjoy a networked wireless home automation system anywhere at home a SPEAKS WAVE yh User Manual download http www remotec com hk zaspx support aspx ZRC 100 USER INTERFACE LAYOUT e Press 4 orv keys to select control category Control e Press BACK key to go back to previous page menu e Press and hold BACK key for 2 seconds to go back to root menu Home A1 Device A2 Devices List A2 1 Scene A3 Scenes List A3 1 Comfort A4 Comforts List A4 1 Sensor A5 Sensors List A5 1 All Off A6 Setup B1 Press and hold lt gt keys simultaneously for 3 seconds to enter Setup menu Press BACK key to go back to previous page Press and hold
5. ame your device please refer to user manual step of B6 Device Config FREQUENTLY ASKED QUESTIONS Q If my Z Wave devices had already added into my Z Wave gateway primary controller network what should I do for my ZRC 100 How to copy my scenes settings to my ZRC 100 A Your ZRC 100 can act as a secondary controller with network information about other devices and scenes setting acquired from your gateway primary controller Please refer to user manual with below steps i ZRC 100 should enter the Learning Mode step of B11 1 Replicating All Network and Device Information from a Primary Controller to your ZRC 100 for details please refer to ZRC 100 user manual ii Gateway should enter the Inclusion Mode to add the ZRC 100 into the network and replicating all network and device information from a primary controller to your ZRC 100 please refer to gateway user manual iii Now ZRC 100 will act as a secondary controller All scenes and device node information will transfer from gateway to ZRC 100 you can On Off the scene through ZRC 100 step of A3 1 iv Your ZRC 100 will acquire scene configuration and node information only That means you have scene copied from gateway but you need to include individual Z Wave device by ZRC 100 if you want to use ZRC 100 to control them individually Can I include all Z Wave devices from the network by ZRC 100 and no need to click the PROG button for each device Yes ZRC
Download Pdf Manuals
Related Search