H-077US-M102 (BKM091) User Manual
Contents
1. WIRELESS PARKING SENSOR US NUMBER PLATE DESIGN USER S MANUAL Q H 003 ISO 9001 2000 FM 78496 QS 9000 March 1998 FM 78495 GENERAL INSTALLATION DIAGRAM DECTECTING RANGE Top View Side View Display 8 0 feet Red wire reversing light wire Black wire ground DISPLAY STATUS Safety Area 5 5 8 0 feet Safety Area 4 0 5 0 feet CUE 4d dang dang I gt 5 0 Danger Area 1 5 3 5 feet Red wire 12V ON ACC Black wire Ground Red wire reversing light wire Black wire ground 2 SD TR Dang dang en O S Alarm Area 1 0 feet 2 en Alarm Area lt 10 feet den u ID learning hole Display Top View Red wire 12V ON ACC Black wire Ground Cee Display Front View So O A B License Plate Sensors INSTALLATION TOOLS SENSOR INSTALLATION DIAGRAM Smooth slope Smooth round objects Objects absorbing T N NN o D o__ Objects hard to be detected wave e g Cotton The display should be installed where easily seen s 2 Drill with the original driller 1 Firstly disassemble the license according to the location of the license plate sensor 3 Insert the cable of the license plate sensor into the hole and then tighten the screws 4 Hide the wires in good order according to various ca2. rs WIRELESS PARKING SENSOR FOR US NUMBER PLATE DESIGN This system consists of digital control box of MCU ultrasonic sensors and display This system detects the distance between the car and the back obstruction by the ultrasonic sensors installed at the rear bumper Distance signal is sent via wireless transmitter The distance and direction of obstruction will be displayed via the digital display and imitation progress bar display with step up sounds the change of alarm sounds progress bar and figures the driver could judge the distance to avoid accident MAIN FUNCTIONS LCD display distance o DangDang alarm sound Wireless transmission of detected distance Easy installation Imitation progress bar display Volume adjustable ID code learning TECHNICAL SPECIFICATIONS Rated voltage DC 12V Controller working temperature 30 70 degree Celsius Working voltage DC 9V 16V Display working temperature 20 70 degree Celsius Rated working current 20 150mA e Size of display 80 4 x 49 8 x 30 2mm e Detecting range 1 0 8 0 feet ALARM MODE Distance Stage Alarm Sound Digital Display Indicator Light gt 8 5 feet Silence Off 5 5 8 0 feet 1 Silence 5 5 8 0 Off 4 0 5 0 feet 2 Dange Dange 4 0 5 0 1 time sec 2 5 3 5 feet 3 Dang Dang 2 5 3 5 2 times sec 1 5 2 0 feet 4 Dang Dang 1 5 2 0 4 times sec 1 0 feet 5 Dang 1 0 On 0 0 0 5 feet 6 Dang 0 0 On Direc
3. tion indicator of left right middle INSTALLATION STEPS 1 Choose the position for license plate sensors 2 Locate the position and drill 3 Install the license plate sensors and hide the wire 4 Install display 5 Connect the whole system according to the General Installation Diagram ID LEARNING Each license plate sensor has a unique ID to ensure the confidentiality and reliability of data transmission during communication with corresponding display The display has the function of learning ID in order that the user could replace the display or control box if necessary Operation as follows 1 Connect the license plate sensor according to the diagram then select reverse gear to activate the license plate sensor Connect the display with power Press the button on the display back The display system will store the ID of the control box automatically See picture A 1 The vehicle must be off during installation N Press the button Picture A 2 Its performance may be affected in following situations heavy rain gravel road bumpy road sloping road and bush very cold hot or moist weather or the sensor is covered by ice snow or mud 3 Test the system to make sure it works normally before using 4 This system is a reversing aid and the manufacturer will take no responsibility for any accident after the kit is installed
Download Pdf Manuals
Related Search