MODEL PORTI-S
Contents
1. 2 When the panel buttons are disabled none of them are usable when the printer cover is closed 3 In this printer the panel buttons is the FEED button 4 In the macro ready mode the FEED button are enabled regardless of the settings of this command however the paper cannot be fed by using these buttons 6 5 Print Position Commands The PORTI S supports the following commands for setting the print position Command Name ESC Set absolute print position ESC Set relative print position ESC a Select justification HT Horizontal tab Set horizontal tab positions Set left margin Set printing area width Set printing area in page mode Select print direction in page mode Set absolute vertical print position in page mode Set relative vertical print position in page mode Set print starting position ESC nL nH Name Set absolute print position Format ASCII ESC HEX 1B 24 Decimal 27 O lt nL lt 255 roos m i weeslm http www woosim com Description Notes Reference ESC nL nH Name Format Range Description Notes Set the distance from the beginning of the line to the position at which subsequent characters are to be printed 1 The distance from the beginning of the line to the print position is nL nH x 256 x vertical or horizontal motion unit inches 2 Setting outside the specified printable area are ignored 3 The horizontal and vertical motion unit2. Print data in page mode LF Name Print and line feed Format ASCII LF HEX OA Decimal 10 Description Print the data in the print buffer and feeds one line based on the current line spacing Note This command sets the print position to the beginning of the line Reference ESC 2 ESC 3 ESC Jn Name Print and feed paper Format ASCII ESC HEX 1B Decimal 27 Range O lt n lt 255 Description Prints the data in the print buffer and feeds the paper n x vertical or horizontal motion unit inches gt oc 2 i http www woosim com ESC dn Name Format Range Description Note Reference FF Name Format Description Note Reference ESC FF Name Format Description Note Reference Print and feed n lines ASCII ESC HEX 1B Decimal 27 O lt n lt 255 Prints the data in the print buffer and feeds n lines 1 This command sets the print starting position to the beginning of the line 2 This command does not affect the line spacing set by ESC 2 or ESC 3 ESC 2 ESC 3 Print and return to standard mode in page mode ASCII FF HEX OC Decimal 12 Prints the data in the print buffer collectively and returns to standard mode 1 The buffer data is deleted after being printed 2 The Printing area set by ESC W is reset to the default setting 3 This command sets the print position to the beginning of the line 4 This command is enabled
3. Upper left A in the figure Lower right C in the figure Woes http www woosim com Notes Default Reference GS nL nH Name Format Range Description Notes 1 When the command is input in standard mode the printer executes only internal flag operation This command does not affect printing in standard mode 2 This command sets the position where data is buffered within the printing area set by ESC W 3 Parameters for horizontal or vertical motion units X or Y differ as follows depending on the starting position of the printing area If the starting position is the upper left or lower right of the printing area data is buffered in the direction perpendicular to the paper feed direction Commands using horizontal motion unit ESC SP ESC ESC Commands using vertical motion unit ESC 3 ESC J GS GS If the starting position is the upper right or lower left of the printing area data is buffered in the paper feed direction Commands using horizontal motion units ESC 3 ESC J GS GS Commands using vertical motion units ESC SP ESC ESC n 0 ESC ESC L ESC W ESC GS GS P GS Set absolute vertical print position in page mode ASCII GS nL nH HEX 1D 24 nL nH Decimal 29 36 nL nH 0 lt nL lt 255 0 lt nH lt 255 Sets the absolute vertical print starting position for buffer character data in page mode 1 This command sets the absolute p
4. vertical starting position 7 The horizontal and vertical motion unit are specified by GS P Changing the horizontal or vertical motion unit does not affect the current printing area 8 The GS P command can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount and it must be in even units of minimum horizontal movement amount 9 Use the horizontal motion unit x for setting the horizontal starting position and printing area width and use the vertical motion unit y for setting the vertical starting position and printing area height 10 When the horizontal starting position vertical starting position printing area width and printing area height are defined as X Y Dx Dy respectively the printing area is set as shown in the figure below http www woosim com Default Reference ESC Tn Name Format Range Description n direction Print Left to right Bottom to Lower left top B in the figure Right to left Top to Upper right bottom D in the figure xL xH yL yH 0 dxL 0 dxH 2 dyL 126 dyH 6 CAN ESC L ESC T GS P Select print direction in page mode ASCH ESC T n HEX 1B 54 n Decimal 27 84 n O lt n lt 3o0r48 lt n lt 5l1 Selects the print direction and starting position in page mode n specifies the print direction and starting position as follows Starting position
5. Name Start End macro definition Format ASCII GS HEX 1D 3A Decimal 29 58 Description Starts ends macro definition Notes 1 Macro definition starts when this command is received during normal operation Macro definition ends when this command is received during macro definition 2 When GS is received during macro definition the printer ends macro definition and clears the definition 3 Macro is not defined when the power is turned on 4 The defined contents of the macro are not cleared by ESC Therefore ESC can be included in the contents of the macro definition 5 If the printer receives GS again immediately after previously receiving GS the printer remains in the macro undefined state 6 The contents of the macro can be defined up to 2048 bytes If the macro definition exceed 2048 bytes excess data is not stored Reference GS roos m i weesim http www woosim com GS rtm Name Format Description Notes Reference Execute macro ASCII GS HEX 1D Decimal 29 0 lt r lt 255 O0 lt t lt 255 m 0 1 Executes a macro 1 r specifies the number of times to execute the macro 2 t specifies the waiting time for executing the macro 3 m specifies macro executing mode When LSB of m 0 The macro executes r times continuously at the interval specified by t When LSB of m 1 After waiting for the period specified by t the ERROR LED indicators blink and the printe
6. Outside of roll ru Cautions 1 Do not paste the paper to the core And the roll paper which has near end mark printing on its near end is recommended Chemicals or oil may change the color of paper or printed characters may fade Change of paper color starts from approx 70 C Pay attention to heat humidity and sun light Color of paper may be changed by being scratched by nail or hard metal etc wees http www woosim com 5 2 Printing position 57 mm Paper Width 4 5 mm 48 mm Printing Area Fig 5 1 wees http www woosim com 6 Print Control Function e Supported Commands List Command Name Function Type Page LF Print and line feed 3 FF Print and return to standard mode 3 1 2 CAN Cancel print data in page mode Miscellaneous function 70 ESC FF Print data in page mode Print 32 3 3 3 6 qf i 3 ESC L Select page mode Miscellaneous function 68 ESC O Set print starting position 54 Set the movement position from the ESC P Black mark detection black mark ESC R Select an international character set 35 ESC S Select standard mode Miscellaneous function ESC 2 Select default line spacing ESCT Select print direction in page mode Print position ESC W Set printing area in page mode Print position weesimm http www woosim com Command ESC X 4 ESC ESC Z ESC a ESC c5 ESC d ESCf ESC v Name Define user defined bit image Set relative p
7. 0x00 OxCO 0x03 OxC1 OxOD and Ox0A The host can ignore these prefix and suffixes wees http www woosim com Appendix A MISCELLANEOUS NOTES 1 Printer mechanism handling 1 Do not pull the paper out when the cover is closed 2 Because the thermal elements of the print head and driver ICs are easy to break so do not touch them with any metal objects 3 Since the areas around the print head become very hot during and just after printing do not touch them 4 Do not use the cover open button except when necessary 5 Do not touch the surface of the print head because bust and dirt can stick to the surface and damage the elements 6 Thermal paper containing Na K Cl ions can harm the print head thermal elements Therefore be sure to use only the specified paper 7 If you want to use label paper please contact your dealer for assistance 2 Thermal paper handling Notes on using thermal paper Chemicals and oil on thermal paper may cause discoloration and faded printing Therefore pay attention to the following 1 Use water paste starch paste polyvinyl paste or CMC paste when gluing thermal paper 2 Volatile organic solvents such as alcohol ester and ketone can cause discoloration 3 Some adhesive tapes may cause discoloration or faded printing 4 If thermal paper touches anything which includes phthalic acid ester plasticizer for a long time it can reduce the image formation ability of the paper and ca
8. ESC GS L GS W Command using y ESC 3 ESC J 3 In page mode the following command use x or y depending on character orientation When the print starting position is set to the upper left or lower right of the printing area using ESC T data is buffered in the direction perpendicular to the paper feed direction Command using x ESC SP ESC ESC W ESC Command using y ESC 3 ESC J ESC W GS GS a gt er j j weesilm http www woosim com Default Reference ESC Name Format Description Notes ESC L Name Format Description Notes When the print starting position is set to the upper right or lower left of the printing area ESC T data is buffered in the paper feed direction Command using x ESC 3 ESC J ESC W GS GS Command using y ESC SP ESC ESC W ESC 4 The command does not affect the previously specified values 5 The calculated result from combining this command with others is truncated to the minimum value of the mechanical pitch x 180 y 360 ESC SP ESC ESC 3 ESC J ESC W ESC GS GS L GS W GS Initialize printer ASCII ESC HEX 1B 40 Decimal 27 64 Clears the data in the print buffer and resets the printer mode to the mode that was n effect when the power was turned on 1 The data in the receive buffer is not cleared 2 The macro definition is not cleared Select page mode ASCII ESC L HEX 1B 4C Decimal 27 7
9. Left justification Center justification Right justification ABC ABCD ABCDE HT Name Format Description Note ABC ABC ABCD ABCD ABCDE ABCDE Horizontal Tab ASCH HT HEX 09 Decimal 9 Moves the print position to the next horizontal tab position 1 This command is ignored unless the next horizontal tab position has been set 2 If the next horizontal tab position exceeds the printing area the printer sets the printing position to Printing area width 1 3 Horizontal tab positions are set with ESC D 4 If this command is received when the printing position is at Printing area width 1 the printer executes print buffer full printing of the current line and horizontal tab processing from the beginning of the next line 5 The default setting of the horizontal tab position for the paper roll is every 0 character a PE j j weesimm http www woosim com Reference ESC D n1 nk NUL Name Format Range Description Notes Default Reference Set horizontal tab positions ASCII ESC D HEX 1B 44 Decimal 27 1 lt n lt 255 0 lt k lt 32 Set horizontal tab position 1 n specifies the column number for setting a horizontal tab position from the beginning of the line 2 k indicates the total number of horizontal tab positions to be set 3 The horizontal tab position is stored as a value of character width x n measured from the beginning of the lin
10. affect the current line spacing roos m i weesim http www woosim com Reference 3 The GS P command can change the horizontal and vertical motion unit However the value cannot be less than the minimum vertical movement amount and it must be in even units of the minimum vertical movement amount 4 In standard mode the vertical motion unit y is used 5 In page mode this command functions as follows depending on the starting position of the printable area When the starting position is set to the upper left or lower right of the printable area using ESC T the vertical motion unit y is used When the starting position is set to the upper right or lower left of the printable area using ESC T the horizontal motion unit x is used ESC 2 GS P 6 3 Character Commands The PORTI S supports the following commands for setting character font and size Command Name ESC SP ESCR ESC ESC ESC E ESC G ESC GS GSB Set right side character spacing Select an international character set Select print mode Turn underline mode on off Turn emphasized mode on off Turn double strike mode on off Turn upside down Select character size Turn white black reverse printing mode on off nos Len j j weesim http www woosim com ESC SP n Name Format Range Description Note Default Reference ESCRn Name Format Range Description Set right side cha
11. are specified by GS P 4 The GS P command can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount and it must be in even units of he minimum horizontal movement amount 5 In standard mode the horizontal motion unit x is used 6 In page mode horizontal or vertical motion unit differs depending on the starting position of the printable area as follows 1 When the starting position is set to the upper left or lower right of the printable area using ESC T the horizontal motion unit x is used 2 When the starting position is set to the upper right or lower left of the printable area using ESC T the vertical motion unit y is used ESC GS GS GS P Set relative print position ASCII ESC HEX 1B 5C Decimal 27 0 lt nL lt 255 0 lt nL lt 255 Set the print starting position based on the current position by using 1 This command sets the distance from the current position to nL nHx256 x horizontal or vertical motion unit a gt EE j j weesim http www woosim com Reference ESCan Name Format Range Description 2 Any setting that exceeds the printable are is ignored 3 When pitch N is specified to the right nL nH x 256 N When pitch N is specified to the left the negative direction use the complement of 65536 4 The print starting position moves from the current position to N x horizontal or vertica
12. d indicates the bit image data Set a corresponding bit to 1 to print a dot or to 0 to not print a dot 6 If the width of the printing area set by GS L and GS W less than the width required by the data sent with the ESC command the following will be performed on the line in question but the printing cannot exceed the maximum printable area The width of the printing area is extended to the right to accommodate the amount of data If step does not provide sufficient width for the data the left margin is reduced to accommodate the data 7 After printing a bit image the printer returns to normal data processing mode 8 This command is not affected by print modes emphasized double strike underline character size or White Black reverse printing except upside down printing mode 9 The relationship between the image data and the dots to be printed is as follows oos m i wees http www woosim com When 8 dot bit image is selected Bit image data d1 d2 d3 Bit image data Print data 7 1dot Print data Single density Double density When 24 dot bit image is selected Bit image data d1 d2 d3 d4 d5 d6 d7 m O Bit image data Print data 1dot Print data Single density Double density vos Len j j w
13. is used for calculating the printing area width The calculated result is truncated to the minimum value of the mechanical pitch 8 If the width set for the printing area is less than the width of one character when the character data is developed the following Left margin Extended to right Printing area width set nL and nH gt j j weesimm http www woosim com Default Reference If the printing area width cannot be extended sufficiently the left margin is reduced to accommodate one character Printable area Left margin Reduced left margin Extended to right If the printing area width cannot be extended sufficiently the right space is reduced 9 If the width set for the printing area is less than one line in vertical the following processing is performed only on the line in question when data other than character data e g bit image user defined bit image is developed The printing area width is extended to the right to accommodate one line in vertical for the bit image within the printable area If the printing area width cannot be extended sufficiently the left margin is reduced to accommodate one line in vertical nL 0 nH 2 GS L GS P ESC W xL xH yL yH dxL dxH dyL dyH Name Format Range Description Set printing area in page mode ASCII ESC W xL xH yL yH dxL dxH dyL dyH HEX 1B 57 xL xH yL yH dxL dxH dyL dyH Decimal 27 87 xL xH yL yH dxL dxH dyL dyH 0 lt xL xH yL
14. only in page mode ESC FF ESC L ESC S Print data in page mode ASCII ESC FF HEX 1B OC Decimal 27 12 In page mode prints all buffered data in the printing area collectively This commands is enabled only in page mode After printing the printer does not clear the buffered data setting values for ESC T and ESC W and the position for buffering FF ESC L ESC S roos m i wees http www woosim com 6 2 Line Spacing Commands The PORTI S supports the following commands for setting line spacing These commands only set the line spacing they do not actually advance the paper The line spacing set using these commands affects the results of LF and ESC d and paper feeding by using the FEED button Command Name ESC 2 Select default line spacing ESC 3 Set line spacing ESC 2 Name Select default line spacing Format ASCII ESC 2 HEX 1B 32 Decimal 27 50 Description Selects 1 7 inch line approximately 3 75mm spacing Note The line spacing can be set independently in standard mode and in page mode Reference ESC 3 ESC 3n Name Set line spacing Format ASCII ESC HEX 1B Decimal 27 Range O lt n lt 255 Description Sets the line spacing to n x vertical or horizontal motion until inches Note 1 The line spacing can be set independently in standard mode and in page mode 2 The horizontal and vertical motion unit are specified by GS P Changing the horizontal or vertical motion unit does not
15. page mode Format ASCH GS i HEX 1D 69 Decimal 29 105 Description Print line amp box in page mode Horizontal length xL xH 256 dot Vertical length yL yH 256 dot Line thickness n dot If the horizontal length is 0 it becomes vertical line Tf the vertical length is 0 it becomes horizontal line 0 lt xL xH yL yH lt 255 0 lt n lt 255 gt oc 2 si http www woosim com 6 12 Black mark detection commands ESC P xL xH Name Format Description Set the movement position from the black mark ASCH ESC P xL HEX 1B 50 Decimal 27 80 The movement position will be set when this command is sent to the printer just once uo01 2911p pee ESC z ESC Name Format Description Black mark yL yH 256 dot lines Movement Position Feed the paper to the movement position ASCII ESC Zz HEX 1B 7A Decimal 27 122 27 Feed the paper to the movement position wees http www woosim com 7 Introduction of Protocol IrDA or Bluetooth 7 1 Frame Structure SOF TOF EOF Start Of Frame Type Of Frame End Of Frame 1 Byte Variable Type of frame Type of frame Value som oe oe seers sey ECS During transmission if COH C1H and or 7DH are contained in data field 7DH should be inserted before the data and the data should be XORed with 20H and sent During reception if 7DH is encountered 7DH should be ignored and the next byte sh
16. printing area set by ESC W are initialized 5 This command switches the settings for the following commands in which the values can be set independently in standard mode and page mode to those for standard mode a gt eTe j j woesze http www woosim com Reference CAN Name Format Description Notes Reference Set right side character spacing ESC SP Select default line spacing ESC 2 ESC 3 6 The following commands are enabled only to set in standard mode Set printing area in page mode ESC W Select print direction in page mode ESC T 7 The following commands are ignored in standard mode Set absolute vertical print position in page mode GS Set relative vertical print position in page mode GS 8 Standard mode is selected automatically when power is turned on the printer is reset or command ESC is used FF ESC FF ESC L Cancel print data in page mode ASCII CAN HEX 18 Decimal 24 In page mode deletes all the print in the current printable area This command is enable only in page mode If data that existed in the previously specified printing area also exists in The currently specified printing area it is deleted ESC L ESC W oos m i wees http www woosim com 6 11 Line amp box commands The PORTI S supports the following line amp box commands Command Name GSi Print line amp box in page mode GS i Name Print line amp box in
17. yH dxL dxH dyL dyH lt 255 except dxL dxH 0 or dyL dyH 0 The horizontal starting position vertical starting position printing area width and printing area height are defined as x0 y0 dx inch respectively x0 xL xH 256 horizontal motion unit y0 yL yH 256 vertical motion unit dx dxL dxH x 256 x horizontal motion unit a gt Pr j j weesimm http www woosim com dy dyL dyH 256 vertical motion unit The printing area is set as shown in the figure below 1 If this commands is input in standard mode the printer executes only internal flag operation This command does not affect printing in standard mode 2 If the horizontal or vertical starting position is set outside the printable area the printer stops command processing and processes the following data as normal data 3 If the printing area width or height is set to 0 the printer stops command processing and processes the following data as normal data 4 This command sets the position where data is buffered to the position specified by ESC T within the printing area 5 If horizontal starting position printing area width exceeds the printable area the printing area width is automatically set to horizontal printable area horizontal starting position 6 If vertical starting position printing area height exceeds the printable area the printing area height is automatically set to vertical printable area
18. 6 Switches from standard mode to page mode 1 This command is enabled only when processed at the beginning of a line in standard mode 2 This command has no effect in page mode 3 After printing by FF is completed or by using ESC S the printer returns to standard mode roos m i wees http www woosim com Reference ESCS Name Format Description Note 4 This command sets the position where data is buffered to the position specified by ESC T within the printing area defined by ESC W 5 This command switches the settings for the following commands in which the values can be set independently in standard mode and page mode to those for page mode Set right side character spacing ESC SP Select default line spacing ESC 2 ESC 3 6 Only valve settings is possible for the following commands in page mode these commands are not executed Select justification ESC a Turn upside down printing mode on off ESC Set left margin GS L Set printable area width GS W 7 The printer returns to standard mode when power is turned on the printer is reset or ESC is used FF CAN ESC FF ESC S ESC T ESC W GS GS Select standard mode ASCII ESC S HEX 1B 53 Decimal 27 83 Switches from page mode to standard mode 1 This command is effective only in page mode 2 Data buffered in page mode are cleared 3 This command sets the print position to the beginning of the line 4 The
19. Character size Resolution Print width Printing speed Specification Direct thermal line printing 42cpl Eng 9 24dots 12 24dots Kor 16 24dots 24 24dots 203dpi 8dots mm 2 inch 48mm 384dots 50mm sec 76 6 103 34 mm Standard model Weight S30 226g S40 264g Including battery amp roll paper Serial RS 232C IrDA Ver1 0 SIR Standard model Interface Bluetooth optional Thermal roll paper PORTI S30 57mm wide 309 Paper supplied PORTI S40 57mm wide 409 PDF417 2 dimension Code128 Code39 112 5 Code93 Barcode supplied UPC EAN KAN JAN CODABAR 10K bytes Printing speed may be slower depending on the data Receive buffer size Note transmission speed and the combination of control commands Rechargeable 7 4V DC 1100mA Li ion 1 hour continuous printing Input 100 250V AC 50 60Hz Battery Battery duration AC adapter Output 8 4VDC 0 8A 4hours full charge time Humidity 10 90 storage ant weesim 10 C 40 C operating Environment 10 C 70 C storage Conditions 30 80 operating MCBF Mean Cycle Between failure http www woosim com 2 Setting up the printer 2 1 Unpacking Your printer box should include these items If any items are damaged or missing please contact your dealer for assistance PORTI S ROLL PAPER Operator s Manual Adaptor for Battery Recharge LEATHERETTE vos Len j j weeslmm htt
20. MODEL PORTI S Portable Printer WOOSIM SYSTEM Inc 501 Daerung Technotown 3th 448 Gasan Dong GeumChun Ku Seoul Korea Tel 82 2 2107 3700 Fax 82 2 2107 3707 URL http www woosim com All specifications are subjected to change without notice wees http www woosim com Copyright PORTES portable printer operator s manual Copyright 2005 by Woosim System Inc All rights reserved The information contained in this manual is the property of Woosim System Inc and may not be reproduced in whole or in part without the prior written permission of Woosim System Inc Trademark a registered trademark of Woosim System Inc All other trademark are the properties of their respective companies Caution Some semiconductor devices are easily damaged by static electricity You should turn the printer OFF before you connect or removed the cable on the rear side in order to guard the printer against the static electricity If the printer is damaged by the static electricity you should turn the printer OFF Notice The contents of this manual are subject to change without notice roos m i weesim http www woosim com EI Introduction The PORTI S is designed for use with electronic instruments such as mobile POS retail transportation warehousing other traveling and mobile computing The general features of PORTI S printer are as follows gt Pocket size 76 6 x 103 x 34mm
21. This command sets the distance from the current position to nL nHx256 x vertical or horizontal motion unit inches 2 This command is ignored unless page mode is selected 3 When pitch N is specified to the movement downward nL nHx256 N When pitch N is specified to the movement upward the negative direction use the complement of 65536 gt eTA j j weesim http www woosim com Reference When pitch N is specified to the movement upward nL nH x 256 65536 N 4 Any setting that exceeds the specified printing area is ignored 5 This command function as follows depending on the print starting position set by ESC T When the starting position is set to the upper left or lower right of the printing the vertical motion unit y is used When the starting position is set to the upper right or lower left of the printing the horizontal motion unit x is used 6 The horizontal and vertical motion unit are specified by GS P 7 The GS P command can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount and it must be in even units of the minimum horizontal movement amount ESC ESC T ESC W ESC GS GS P ESC O xL xH yL yH Name Format Description Set print starting position ASCII ESC O xL xH yL yH HEX 1B 4F xL xH yL yH Decimal 27 79 xL xH yL yH Set horizontal starting position and vertical starting pos
22. ation Data Transmission Rate Notice If the quantity of data which is printed at once is more than 20K byte on Bluetooth communication it would cause the buffer to overflow and the data to get damaged woeesz http www woosim com 4 Using the printer 4 1 Control panel Power button Mode button Feed button Data printer PORTES N Error lamp cs Fig 4 1 gt Button Feed button Press the FEED button once to advance paper one line You can also hold down the FEED button to feed paper continuously Mode button MODE Button is for use to change communication mode Refer to 2 5 Setting operation mode for details about mode conversion If you want to set to RS 232C Mode just connect the communication cable to connector of the printer and then the mode will be changed automatically gt Panel lamp Power The POWER lamp is on whenever the printer is on But when the battery is almost exhausted this led flashes with red color occasionally In this case you must recharge the battery by using the adapter Error This indicates an error such as paper end or cover open mode conversion etc Data The Data lamp is on whenever the printer receives data roan Len j j weeslmm http www woosim com 4 2 The self test The self test checks whether the printer has any problems If the printer does not function properly contact your dealer The self test checks the following Make s
23. ct printer model to install and press Next Selecting Printer Model e Select printer model to install and press Db Next button to continue Printer Models Fig 4 3 4 Select the port connected to printer and press Next Selecting Printer Port e Select the port connected to printer 1 press Next button to continue Printer Ports F LPT2 J LPT3 f iS WBAROCOMESHPDeskJe wees ht tp www woosim com 5 If the installation has done successfully press OK Printer Driver Setup LA A L The Installation has done successfully V Set as default printer Copyright C 2002 Woosim System Fig 4 5 4 4 Bit image download The PORTI S Printer supports bit image download to the internal Flash ROM The bit image download require the Porti_Download application and PCX file Porti_Download Application The Porti_Download application can download by internet http www woosim com PCX file The picture must be black or white PCX file and the width of picture must be x8 pixel Refer to Porti_ Download manual for details about bit image download You can print out the downloaded picture with referred ESC f command See sec 6 6 wees ht tp www woosim com 5 Consumable Parts 5 1 Recommended paper Type Thermal Paper Paper width 57mm Paper thickness 7045 Mm Outer diameter 30 or less PORTI S30 40mm or less PORTI S40 Recording side
24. cter data as bar code data 7 If n is outside of the specified range the printer stops command processing and processes the following data as normal data yeeslem http www woosim com 8 Be sure to keep spaces on both right and left sides of a bar code Spaces are different depending on the types of the bar code Reference GS h GS w GS H ESC L ESC W ESC FF GS Hn Name Format Range Description ESC Z m nk d dl Name Format Description Turn HRI characters print mode ON OFF ASCI GS H n HEX 1D 48 n Decimal 29 n n 0 1 GS H n turns HRI characters print mode on or off When the LSB least significant bit of n is 1 HRI characters print mode is turned on When it is 0 HRI character print mode is turned off The default setting is n 0 dn Print 2D barcode ASCII ESC m n k d dl dn HEX 1B m n k d dl dn Decimal 27 m n k d dl dn 1 lt m lt 7 O lt n lt 8 2 lt k lt 5 1 lt d lt 65535 Print 2D bar code PDF417 format m specifies column number of 2D bar code n specifies security level to restore when bar code image is damaged k is used for define horizontal and vertical ratio d is consist of 2 byte 1st byte is lower number And 2nd byte is upper number wees http www woosim com 6 9 Macro Function Commands The PORTI S supports the following macro function commands Command Name GS Start end macro definition Execute macro GS
25. cters on the line are aligned at the baseline 6 The ESC command can also turn double width and double height modes on or off n 0 ESC Turn white black reverse printing mode On Off ASCII GS B n HEX 1D 42 n Decimal 29 n 0 lt n lt 255 Turns on or off White Black reverse printing mode yeeslem http www woosim com Notes 1 When the LSB is 0 white black reverse printing mode is turned on 2 When the LSB is 1 white black reverse printing mode is turned off 3 Only the lowest bit of n is valid 4 This command is available for built in characters and user defined characters 5 When white black reverse printing mode is on it also applied to character spacing set by ESC SP 6 This command does not affect the space between lines 7 White black reverse mode has a higher priority than underline mode Even if underline mode is on it is disabled but not canceled when white black reverse 6 4 Panel Button Commands The PORTI S supports the following command for enabling and disabling the panel button Command Name ESC c5 Enable disable panel buttons ESC c5n Name Enable Disable panel buttons Format ASCII ESC c HEX 1B 63 Decimal 27 Range O lt n lt 255 Description Enables or disables the panel buttons When the LSB is 0 the panel buttons are enabled When the LSB is 1 the panel buttons are disabled 1 Only the least significant bit of n is valid roos m i weesim http www woosim com
26. de system as follows Barcode System Number of character Remarks UPC A 11 lt Kk lt 12 48 lt d lt 57 UPC E 11 lt k lt 12 48 lt d lt 57 CODE39 1 lt k 48 lt d lt 57 65 lt d lt 90 d 32 36 37 43 45 46 47 1 lt k even number 48 lt d lt 57 1 lt k CODABAR 48 lt d lt 57 65 lt d lt 68 d 36 43 45 46 47 58 Wees http www woosim com Barcode System Number of characters Remarks CODE39 1 lt n lt 255 48 lt d lt 57 65 lt d lt 90 d 32 36 37 43 45 46 47 CODABAR 1 lt n lt 255 48 lt d lt 57 65 lt d lt 68 d 36 43 45 46 47 58 CODE93 lens 255 O lt d lt 127 CODE128 2 ns 255 O lt d lt 127 Notes 1 This command ends with a NUL code 2 When the bar code system used is UPC A or UPC E the printer prints the bar code data after receiving 12 bytes bar code data and processes the following data as normal data 3 When the bar code system used in EAN13 the printer prints the bar code after receiving 13 bytes bar code data and processes the following data as normal data 4 When the bar code system used in EAN8 the printer prints the bar code after receiving 8 bytes bar code data and processes following data as normal data 5 The number of data for ITF bar code must be even numbers When an odd number of data is input the printer ignores the last received data 6 n indicates the number of bar code data and the printer processes n bytes from the next chara
27. e The character width includes the right side character spacing and double width characters are set with twice the width of normal characters 4 This command cancels the previous horizontal tab settings 5 When setting n 8 the print position is moved to column 9 by sending HT 6 Up to 32 tab positions k 32 can be set Data exceeding 32 tab positions is processed as normal data 7 Transmit n k in ascending order and place a NUL code 0 at the end 8 When n k is less than or equal to the preceding value n k 1 tab setting is finished and the following data is processed as normal data 9 ESC D NUL cancels all horizontal tab positions 10 The previously specified horizontal tab positions do not change even if the character width changes 11 The character width is memorized for each standard and page mode The default tab positions are at intervals of 0 characters HT gt eTA j j weesim http www woosim com GS L nL nH Name Format Range Description Notes Default Reference Set left margin ASCII GS L HEX 1D 4C Decimal 29 76 0 lt nL lt 255 0 lt nH lt 255 Set the left margin using nL and nH 1 The left margin is set to nL nHx256 x horizontal motion unit inches Printable area Left margin Printing area width 2 This command is effective only processed at the beginning of the line in standard mode 3 If this command is input in page mode the printer perfor
28. e 2 ae Double height mode not selected Double height mode selected or oo Double width mode not selected Double width mode selected Off Undefined On Undefined Off 00 0 Underline mode not selected On 80 128 Underline mode selected Woese http www woosim com Note 1 When both double height and double width modes are selected quadruple size characters are printed 2 The printer can underline all characters but can not underline the space set by HT 3 The thickness of the underline is that selected by ESC regardless of the character size 4 When some characters in a line are double or mode height all the characters on the line are aligned at the baseline 5 ESC can also turn on or off underline mode However the setting of the last received command is effective 7 GS can also select character size However the setting of the last received command is effective Reference ESC ESC E GS ESC n Name Turn underline mode on off Format ASCII ESC HEX 1B Decimal 27 Range 0 lt n lt 1 Description Turns underline mode on or off based on the following values of n Function n Turns off underline mode Turns on underline mode 1 dot thick Turns on underline mode 2 dot thick Notes 1 The printer can underline all characters including right side character spacing but cannot underline the space set by HT 2 The printer cannot underline white black inverted charac
29. eeslmm http www woosim com ESC X 4 x y dl dk Name Format Description Print bit image ASCII ESC X 4 x y dl dk HEX 1B 58 34 x y dl dk Decimal 27 88 52 x y dl dk ESC X 4x y d1 d x y print bit image using x 8 dots in the horizontal direction and y dots in the vertical direction Horizontal direction dots x 8 dots Vertical direction dots y dots Q iO roan Len j j weeslmm http www woosim com EEE OINI Note Reference ESC fn Name Format Range Description Reference EN CHTIITIT CHRTIITITI CMRTIITIITI CHTIITIITI ET EOT CECCCEEEI CCC T nn 8 8 8 ESC X 4 is supported in Porti_W S produced after August 2002 but it s not supported in others yet ESC L ESC W ESC O ESC FF Print downloaded bit image ASCH ESC f HEX 1B 66 Decimal 27 n 0 1 48 49 ESC f prints a downloaded bit image specified by n as follows prints a downloaded bit imagel when n 0 or n 48 prints a downloaded bit image2 when n 1 or n 31 ESC L ESC W ESC O ESC FF woesza http www woosim com 6 7 Status Commands The PORTI S supports the following status transmission command Command Name ESC v Transmit paper sensor status ESC v Name Transmit paper sensor status Format ASCII ESC v HEX 1B 76 Decimal 27 118 Description ESC v transmits the s
30. gt Light weight S30 226g S40 264g for true mobility gt Very silent printing thru direct thermal printing method gt High speed 50mm sec gt High resolution 203dpi 8dots mm gt Easier paper loading by CLAMSHELL design gt Support text and graphic printing gt Serial RS 232C IrDA Ver 1 0 SIR Bluetooth optional interface gt Easier maintenance with self diagnostics gt Support bit image logo download gt Flow control Software XON XOFF X Hardware flow control not supported in printer wees http www woosim com Ei Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer Using the Printer Be careful not to drop or bump the printer on a hard surface Do not install the printer in direct sunlight or such areas Suitable environment for the use of the printer is as follows Operating temperature 10 C to 40 C Relative humidity 10 to 90 no condensation Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine Do not remove or reinstall the communication cable during printing or transmission wees http www woosim com CONTENTS 1 Outline 1 1 Model classifications 1 2 Specifications 2 Setting up the printer 2 1 Unpacking 2 2 Outer appearances and part name 2 3 Replacing the paper roll 2 4 Power connection 2 4 1 Specified power
31. ition in page mode Horizontal starting position xL xH 256 horizontal motion unit Vertical starting position yL yH 256 vertical motion unit This command is effective only in page mode a gt PE j j weesim http www woosim com 6 6 Bit Image Commands The PORTI S supports the following bit image command Command Name ESC Select bit image mode ESC X 4 Print bit image ESC f print downloaded bit image ESC m nL nH dl dk Name Select bit image mode Format ASCII ESC m nL nH dl dk HEX 1B 2A m n nH dl dk Decimal 27 42 m nl nH dl dk m 0 1 32 33 0 lt nL lt 255 0 lt nH lt 3 O0 lt d lt 255 Description Selects a bit image mode using m for the number of dots specified by nL and nH as follows Vertical direction Horizontal direction mode N f vee Dot density Dot density Number of Data of Dots o Sdotsinde 8 60DPI 90 DPI nie p56 8 dot double e 60 DPI 180 DPI nL nHx256 24 dot single 180DPI 90 DPI nL nHx256 x3 24 dot double 180 DPI 180 DPI nL nHx256 x3 Notes 1 If the values of m is out of the specified range nL and data following are processed an normal data 2 The nL and nH indicate the number of dots of the bit image in the horizontal direction wees http www woosim com 3 The number of dots is calculated by nL nH x 256 4 If the bit image data input exceeds the number of dots to be printed on a line the excess data is ignored 5
32. l motion unit 5 The horizontal and vertical motion unit are specified by GS P 6 The GS P command can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount and it must be in even units of the minimum horizontal movement amount 7 In standard mode the horizontal motion unit is used 8 In page mode the horizontal or vertical unit differs as follows depending on the starting point of the printing area When the starting position is set to the upper left or lower right of the printable area using ESC T the horizontal motion unit x is used When the starting position is set to the upper right or lower left of the printable area using ESC T the vertical motion unit y is used ESC ESC P Select justification ASCII ESC a HEX 1B 61 Decimal 27 97 0O lt n lt 2 48 lt n lt 50 Aligns all the data in one line to the specified position n selects the type of justification as follows n Justification Right justification wees http Www woosim com Default Example 1 The command is enabled only when processed at the beginning of the line in standard mode 2 If this command is input in page mode the printer performs only internal flag operations 3 This command has no effect in page mode 4 This command executes justification in the printing area 5 This command justifies the space area according to HT ESC or ESC n 0
33. ms only internal flag operations 4 This command does not affect printing in page mode 5 If the setting exceeds the printable area the maximum value of the printable area is used 6 The horizontal and vertical motion units are specified by GS P Changing the horizontal and vertical motion unit does not affect the current left margin 7 The horizontal motion unit x is used for calculating the left margin The calculated result is truncated to the minimum value of the mechanical pitch nL 0 nH 0 GS P GS W roos m i weesim http www woosim com GS W nL nH Name Format Range Description Notes Set printing area width ASCI GS W HEX 1D 57 Decimal 29 87 0 lt nL lt 255 0 lt nH lt 255 Sets the printing area width to the area specified by nL and nH 1 The printing area width is set to nL nHx256 x horizontal motion unit inches Printable area Left margin Printing area width 2 This command is effective only processed at the beginning of the line 3 In page mode the printer performs only internal flag operations 4 This command does not affect printing in page mode 5 If the left margin printing area width exceeds the printable area printable area width left margin is used 6 The horizontal and vertical motion units are specified by GS P Changing the horizontal and vertical motion units does not affect the current left margin 7 The horizontal motion unit x
34. n cause the printed image to fade Therefore when storing thermal paper in a card case or sample notebook be sure to use only products made from polyethylene polypropylene or polyester 5 If thermal paper touches diazo copy paper immediately after copying the printed surface may be discolored 6 Thermal paper must not be stored with the printed surfaces against each other because the printing may be transferred between the surfaces gt PE j j weesim http www woosim com 7 If the surface of thermal paper is scratched with a hard metal object such as a nail the paper may become discolored Notes on thermal paper storage Since color development begins at 70 C 158 F thermal paper should be protected from high temperature humidity and light both before and after printing 1 Store paper away from high temperature and humidity Do not store thermal paper near a heater or in enclosed places exposed to direct sunlight 2 Avoid direct light Extended exposure to direct light may cause discoloration or faded printing 3 Others Because this printer uses plated steel the manual cutting edge may be subject to rust However this does not affect the printer performance weeslm http www woosim com
35. ort Standard IrDA 1200 bps 2400 bps 4800 bps 9600 bps 19200 bps Baud Rate 38400 bps 57600 bps 9600 bps 7 Data bit Data Bit 8 Data bit No Parity Parity Bit Even Parity Odd Parity Density Low Density Density Medium Density High Default Protocol Protocol Lotte Protocol No use Use Low Medium 8 Sensor Medium2 High Table 1 weeslem http www woosim com 3 Interface 3 1 RS 232C serial The PORTI S printer has an RS 232C serial interface is connected by means of a 6 pin male connector In the following table the signals present on the connector are listed Fig 3 1 Pinno Signal Name Direction Function PRO Receive data Transmit data Tab 3 1 http www woosim com 3 2 Infrared bidirectional serial The PORTI S has a serial interface for bi directional data exchange The infrared port is the upper edge part of the left side Infrared Port Fig 3 2 1 To use the PORTI S s infrared port a computer or Personal Digital Assistant PDA with IR port is required 2 Position a PDA conforming to the specifications in point not more than A E E 8 50 centimeter away from the printer s infrared port Make sure the two ports are in front of each other with an angle of not more than 15 on the four sides see fig 3 3 ses Len j j weesim http www woosim com 3 3 Bluetooth Category Specific
36. ould be XORed with 20H and stored wees http www woosim com 7 2 Process of Getting the Printer Status HOST PRINTER Inquiry of Printer Status Response of Printer Status It is recommended that the host send the same inquiry up to 5 times with 400ms time interval in case of no response from the printer 7 2 1 Frame Format 7 Le Inquiry of printer status Response of printer status Status 1 Byte Previous ID 1 Byte x IMPORTANT This function is not yet implemented fully Currently the status byte is fixed to 0x02 However this process can be used to check the communication wees http www woosim com 7 3 Process of Printing Data HOST PRINTER Sending ENQ frame Sending ACK frame Sending Print Data frame Sending EOT ETX frame Sending NACK frame Resending Print Data frame In normal operation after receiving the print data frame the printer sends EOT prints out the data and sends ETX And it will wait for the next frame Conditions of NACK frame issued 1 Different checksum value 2 No data byte received 200ms after the previous byte received 3 No EOF End of frame at the end 4 No predefined number in Data Length field wees http www woosim com 7 3 1 Format of Print Data Frame DATA D DATA ID Print DATA Length Number Data 1 4 2 4 By
37. p www woosim com 2 2 Outer appearances and part name gt Part Name Paper cover Paper cover lock Manual Cutter Feed button Error lamp Infrared Transmitter Receiver Communication connector Fig 2 1 weeslm http www woosim com gt Dimensions Fig 2 2 weesz http www woosim com 2 3 Replacing the paper roll Note Be sure to use paper rolls that meet the specifications Do not use paper rolls that have the paper glued to the core because the printer cannot detect the paper end 1 Make sure that the printer is not receiving data otherwise data may be lost 2 Open the paper roll cover by applying your finger on both side of printer push it up when the lock is released as shown in the drawing Fig 2 3 3 Remove the used paper roll core if there is one 4 Insert the paper roll as shown Fig 2 4 vos Len j j weeslmm http www woosim com 5 Be sure to not the correct direction that the paper comes off the roll Fig 2 5 6 Pull out a small amount of paper and then close the cover as shown Fig 2 6 7 Tear off the paper as shown Fig 2 7 Wees http www woosim com 2 4 Power connection 2 4 1 Specified power supply The following specifications are requested for Power supply Vpp DC 7 4V Standby 60mA and Max 3A 2 4 2 Installation Remove the battery pack NOTE Before installing or removing the battery pack t
38. r waits for the FEED button to be pressed After the button is pressed the printer executes the macro once The printer repeats the operation r times 4 The waiting time is t x 100 ms for every macro execution 5 If this command is received while a macro is being defined the macro definition is aborted and the definition is cleared 6 If the macro is not defined or if is 0 nothing is executed 7 When the macro is executed m 1 paper always cannot be fed by using the FEED button GS roos m i weesim http www woosim com 6 10 Miscellaneous function commands The PORTI S supports the following miscellaneous function commands Command Name GSP Set horizontal and vertical motion units ESC Initialize printer ESC L Select page mode ESC S Select standard mode CAN Cancel print data in page mode GSPxy Name Set horizontal and vertical motion units Format ASCII GS P x HEX 1D 50 x Decimal 29 80 x Range 0 lt x lt 255 0 lt y lt 255 Description Sets the horizontal and vertical motion units to approximately 25 4 x mm 1 x inch and approximately 25 4 y mm 1 y inch respectively When x and y are set to 0 the default setting of each value is used Notes 1 The horizontal direction is perpendicular to the paper feed direction and the vertical direction is the paper feed direction 2 In standard mode the following commands use x or y regardless of character rotation upside down Command using x ESC SP ESC
39. racter spacing ASCII ESC SP HEX 1B 20 Decimal 27 O lt n lt 255 Sets the character spacing for the right side of the character to n x horizontal or vertical motion units inches 1 The right side character spacing for double width mode is twice the normal value When characters are enlarged the right side character spacing is n times normal value 2 This command sets values independently in each mode 3 The horizontal and vertical motion unit are specified by GS P Changing the horizontal or vertical motion unit does not affect the current right side spacing 4 The maximum right side spacing if 255 180 inches Any setting exceeding the maximum is converted to the maximum automatically n 0 GSP Select an international character set ASCII ESC R n HEX 1B 52 n Decimal 27 n 0O lt n lt 10 Selects an international character set n from the following table roos m i wees http www woosim com Character set n Character set Character set France Denmark II Default n 0 ESC n Name Format Range Description Bit Select print mode ASCII ESC HEX 1B Decimal 27 O lt n lt 255 Select print mode s using n as is follows Off On Hex il Decimal Function esse seu Character font B 9 x 24 on underines o Unac nes om Unac ines o Unae nes Pak la Emphasized mode not selected ze ae LE Emphasized mode selected e
40. rint position Print 2D barcode Select justification Enable disable panel buttons Print and feed n lines Print downloaded bit image Transmit paper sensor status ESC z ESC y ESC GS GS GS Function Type Bit image Print position Barcode Print position Panel button Print Bit image Status Feed the paper to the movement position Black mark detection Turn upside down printing mode on off Select characters size Set absolute vertical print position in page mode Start end macro definition Turn white black reverse printing mode On off Select printing position of HRI characters Set left margin Set horizontal and vertical motion units Set printing area width Set relative vertical print position in page mode Execute macro Set barcode height Print box amp line in page mode Print bar code Set barcode width Character Character Print position Macro function Character Barcode Print position Miscellaneous function Print position Print position Macro function Barcode Box amp line command Barcode Barcode 64 47 68 48 53 66 61 71 62 61 weesim http www woosim com 6 1 Print Commands The PORTI S supports the following commands for printing character and advancing paper Command Name LF Print and line feed ESC J Print and feed paper ESC d Print and feed n lines FF Print and return to standard mode in page mode
41. rint position to nL nHx256 x vertical or horizontal motion unit inches 2 This command is effective only in page mode 3 If the nL nHx256 x vertical or horizontal motion unit exceeds the specified printing area this command is ignored gt eT j j weesim http www woosim com Reference GS nL nH Name Format Range Description Notes 4 The horizontal starting buffer position does not move 5 The reference starting position is that specified by ESC T 6 This command operates as follows depending on the starting position of the printing area specified by ESC T When the starting position is set to the upper left or lower right this command sets the absolute position in the vertical direction When the starting position is set to the upper right or lower left this command sets the absolute position in the horizontal direction 7 The horizontal and vertical motion unit are specified by GS P 8 The GS P command can change the horizontal and vertical motion unit However the value cannot be less than the minimum horizontal movement amount and it must be in even units of the minimum horizontal movement amount ESC ESC T ESC W ESC GS P GS Set relative vertical print position in page mode ASCI GS nL nH HEX 1D nL nH Decimal 29 nL nH 0 lt nL lt 255 0 lt nH lt 255 Sets the relative vertical print starting position from the current position in page mode 1
42. scription When the LSB is 1 upside down mode is turned on 1 Only the lowest significant bit of n is valid 2 This command is enabled only when processed at the beginning of a line in standard mode 3 When this command is input in page mode the printer performs only internal flag operations 4 This command does not affect printing in page mode 5 In upside down printing mode the printer rotates the line to be printed by 180 degree and then prints it Paper feed direction Select character size ASCII GS HEX 1D Decimal 29 O lt n lt 255 1 lt vertical number of times lt 8 1 lt horizontal number of times lt 8 Selects the character width using bits 0 to 2 and selects the character height using bits 4 to 7 as follows roos m i weesim http www woosim com Hex Decimal Width Hex Decimal Height 1 normal Character Height Selection Character Width Selection Notes Default Reference GSBn Name Format Range Description 1 This command is all characters effective 2 If n is outside of the defined range this command is ignored 3 In standard mode the vertical direction is the paper feed direction and the horizontal direction is perpendicular to the paper feed direction 4 In page mode vertical and horizontal directions are based on the character orientation 5 When characters are enlarged with different sizes on one line all the chara
43. ss the MODE Button one more time the Error Lamp twinkles 6 times The baud rate has set to 38 400 bps roos na i weesim http www woosim com gt Press FEED Button one time Power Lamp twinkles 3 times and Error Lamp twinkles 2 times Press MODE Button one time Error Lamp twinkles one time The Data Bit has set to 7 data bit gt Press FEED Button one time Power Lamp twinkles 4 times and Error Lamp twinkles 1 time Press MODE Button one time Error Lamp twinkles 2 times The Parity bit has set to even parity bit gt Press FEED Button one time Power Lamp twinkles 5 times and Error Lamp twinkles 1 time Press MODE Button one time Error Lamp twinkles 2 times after then press MODE Button again the Error Lamp will twinkle 3 times The density has set to High gt Press FEED Button one time Power Lamp twinkles 7 times and Error Lamp twinkles 1 time Press MODE Button one time Error Lamp twinkles 2 times The mark has set to Use If all the mode have set press the MODE Button and the FEED Button at the same time after then release the buttons at the same time The printer will print out the mode status which has modified PROTOCOL IrDA 38 400 BAUD 7 DATA BIT EVEN PARITY DENSITY HIGH If the status is not correct please try it again according to the procedure roos m i weesim http www woosim com POWER Lamp MODE Lamp RS 232C Communication Protocol IrDA or Bluetooth P
44. supply 2 4 2 Installation Remove the battery pack 2 5 Setting operation mode 3 Interface 3 1 RS 232C serial 3 2 Infrared bidirectional serial 3 3 Bluetooth 4 Using the printer 4 1 Control panel 4 2 The self test 4 3 Driver installation 4 4 Bit image download 5 Consumable Parts 5 1 Recommended paper 5 2 Printing position 6 Print Control Function 6 1 Print Commands 6 2 Line Spacing Commands 6 3 Character Commands 6 4 Panel Button Commands 6 5 Print Position Commands roos m i weesim http www woosim com 6 6 Bit Image Commands 6 7 Status Commands 6 8 Barcode Commands 6 9 Macro Function Commands 6 10 Miscellaneous function commands 6 11 Line amp box commands 6 12 Black mark detection commands 7 Introduction of Protocol IrDA or Bluetooth 7 1 Frame Structure 7 2 Process of Getting the Printer Status 7 2 1 Frame Format 7 3 Process of Printing Data 7 3 1 Format of Print Data Frame 7 3 2 Format of ENQ Frame 7 3 3 Format of ACK Frame 7 3 4 Format of NACK Frame 7 3 5 Format of ETX Frame 7 3 6 Format of EOT Frame Appendix wees http www woosim com 1 Outline 1 1 Model classifications PORTI S Model name Size of roll paper 30 57mm wide 30 40 57mm wide 40 Interface None Serial IrDA BT Bluetooth Power None DC 7 4V weeslm http www woosim com 1 2 Specifications Item Printing method Characters per line
45. tatus of a paper sensor as 1byte of data When the paper roll end sensor detects a paper printer transmits the NULL H00 data When the paper roll end sensor doesn t detect a paper printer don t Transmit anything wees http www woosim com 6 8 Barcode Commands The PORTI S supports the following barcode commands Command Name GSh Set barcode height GS w Set barcode width GSk Print bar code GS H Select printing position of Human Readable Interpretation HRI characters GShn Name Set barcode height Format ASCII GS HEX 1D Decimal 29 Range 0 lt n lt 255 Description GS h n selects the height of a barcode n specifies the number of dots in the vertical direction One dot corresponds 1 8mm The default setting is n 80 GS wn Name Set barcode width Format ASCH GS HEX 1D Decimal 29 Range n 0 3 lt n lt 5 Description GS w n selects the horizontal size of a barcode The default setting is n 0 gt oc 2 i http www woosim com GS k m d1 dk NUL GS k mn d1 dn Name Print barcode Format DASCI GS m d1 dk NUL HEX 1D m d1 dk 00 Decimal29 m d1 dk 0 ASCII GS k m n dl dn HEX 1D 6B m n dl dn Decimal29 107 m n dl dn Range D 0 lt m lt 6 k and d depends on the bar code system used 0 lt m lt 6 n and d depends on the bar code system used Description GS k m d1 dk NUL selects a barcode system and print the barcode m specifies a bar co
46. te Bytes Bytes 7 Data ID number 0 9 0x30 0x39 Every time the host sends a new print data frame it increases this number Data Length 0001 9999 Each number must be an ascii code Checksum 2 bytes The first byte is the result of XOR of even number of data in Print data field and the second byte is that of odd number Example If SAMPLE TEST is in Print Data field the data length will be 0011 0x30 0x30 0x31 0x31 and the first byte of checksum will be the result of XOR of S M L space E and T and the second byte that of A P E T and S It is recommended that the host goes back to the initial stage in case that it receives neither EOT nor NACK from the printer 1 sec after it has sent the print data frame 7 3 2 Format of ENQ Frame COH 0x05 gt It is recommended that the host send the same ENQ frame up to 10 times with 400ms time interval in case of no response from the printer wees http www woosim com 7 3 3 Format of ACK Frame COH 0x06 7 3 4 Format of NACK Frame COH Ox15 7 3 5 Format of ETX Frame Data ID No CIH 7 3 6 Format of EOT Frame COH 0x04 7 Printer will send this frame after it receives the print data frame successfully x IMPORTANT In every frame coming from the printer 1 Byte of Null is preceded to SOF and CR and LF are followed by EOF For example the actual data of ETX frame is
47. ters 3 When underline mode id turned off by setting the value of n to 0 or 48 the following data is not underlined and the underline thickness set before the mode woeesza http www woosim com Default Reference ESCEn Name Format Range Description Default Reference is turned off does not change The default underline thickness is 1 dot 4 Changing the character size does not affect the current underline thickness 5 Underline mode can also be turned on or off by using ESC Note however that the last received command is effective n 0 ESC Turn emphasized mode On Off ASCII ESC E n HEX 1B 45 n Decimal 27 n 0 lt n lt 255 Turns emphasized mode on of off When the LSB least significant bit is 0 emphasized mode is turned off When the LSB least significant bit is 1 emphasized mode is turned on 1 Only the least significant bit of n is enabled 2 This command and ESC turn on and off emphasized mode in the same way Be careful when this command is used with ESC n 0 ESC ESC n E E Name Format Range Description Turn On Off upside down printing mode ASCII ESC n HEX 1B 7B n Decimal 27 n 0 lt n lt 255 Turns upside down printing mode on of off When the LSB is 0 upside down mode is turned off roos m i weesim http www woosim com Default n 0 Example n 0 ABCD EFGH GS n Name Format Range De
48. ure paper roll has been installed properly Turn on the power while holding down the FEED button The self test begins The self test prints the current printer status which provides the control ROM version and the communication method setting After printing the current printer status self test printing will print a pattern using the built in character set The self test automatically ends The printer is ready to receive data as soon as it completes the self test wees http www woosim com 4 3 Driver installation The driver installation instruction were written for the printer to be used with the Infrared port and serial port RS 232C Make sure that your PC has built in infrared device Ir DA Ver1 0 Printer driver can download by Internet http www woosim com Installing the PORTI S Printer Driver on Windows 98 ME 2000 XP 1 You must install new driver after deleting old driver Delete the old driver Reboot the computer Tf there is not any installed driver you can install new driver immediately Run the setup exe Press the Next after checking the supported Operating System Printer Driver Setup i Press Next button to continue Supported operating System Windows XP Home x86 Windows XP Professional x86 Windows NET Server x86 Terminate all running applications before installing driver _ coma Fig 4 2 wees ht tp www woosim com 3 Sele
49. urn the printer power off If the printer is not used for a long time remove the battery pack from printer To install battery pack proceed as follows 1 Installing the battery pack Insert the battery pack in the direction of the arrow at hole Fig 2 8 vos Len j j weeslmm http www woosim com Push the top of the battery pack Fig 2 9 To remove battery pack proceed the above order reverse TOOS Len j j weeslmm http www woosim com 2 5 Setting operation mode 1 Press the MODE Button until the Error Lamp twinkles 5 times 2 Change the mode and option using the MODE Button according to the MODE Table 1 FEED Button use for changing MODE status Power Lamp MODE Button use for changing OPTION status Error Lamp Example The defaults of the printer are RS 232C 9600 BPS 8 DATA BIT NO PARITY DENSITY LOW MARK NOUSE If a user wants to modify the defaults with PROTOCOL IrDA 38400 BPS 7 DATA BIT EVEN PARITY DENSITY HIGH MARK USE gt Press MODE Button until Error Lamp twinkles 5 times and release the button You will see the Power Lamp twinkles one time and the Error Lamp twinkles 1 time Press the MODE Button one time and the Error Lamp twinkles twice The interface mode has set to Protocol IrDA mode gt Press FEED Button one time Power Lamp twinkles twice and Error Lamp twinkles 4 times Press MODE Button one time Error Lamp twinkles 5 times and pre
Download Pdf Manuals
Related Search