User Manual
Contents
1. lt WITNESS 6 SVC400P SVC800P 4 8 Camera Live Tracking Vehicle DVR Installation Manual Version 1 0 e WITNESS 10 11 12 13 IVIAIIN FEATURES ss caccocscncssastsucnenctanssanannaentandinnsatadioeoantanesnnie PRODUCT OVERVIEW ii DIMENSIONS aaa PACKAGE CONTENTS MOUNTING AND ENVORNMENTAL REQUIREMENTS INSTALLATION TOOLS nitrer t rh RE rr PPAR IH RE n pea Por her RES INSTALLATION INSTRUCTIONS es CONNECTING THE POWER eene CONNECTING INPUTS AND OUTPUTS 9 1 The A V Cable Definition Video Input AV output 9 2 Specifications for the SENSOR BOX sensor inputs and outputs 9 3 Specifications for 485 and 232 serial ports WORKING STATUS aiittes di ome koE nou Eae Patna ad dn nr sa ii INERTIAL SENSOR CONNECTION e eeeeeee HDD INSTALLATION eee SIM CARD INSTALLATION eene SVC400P SVC800P Installation Manual WITNE S S SVC400P SVC800P Installation Manual 1 MAIN FEATURES The SVC400P SVC800P is an embedded Mobile Digital Video Recorder MDVR that provides the perfect surveillance solution for vehicles It features H 264 video compression which guarantees a high quality image high compression rate for smooth and fast network transmission A special movable plastic HDD case allows you remove and access the stored data easily2. battery Connect with vehicle ignition to let the System start up need provide 12V 24V DC power as signal ON OFF Ignition Signal Input Yellow e WITN FE S S SVC400P SVC800P Installation Manual 9 CONNECTING INPUTS AND OUTPUTS 9 1 The A V Cable Definition Video Input AV output Specifications for the PINs red 12V 0 6A AVINI wh ite AUDIO black GND No color VIDEO red 12V 0 6A AVIN2 white AUDIO black GND No color VIDEO red 12V 0 6A AVINS white AUDIO black GND No color VIDEO red 12V 0 6A AVIN4 white AUDIO black GND No color VIDEO VIDEO OUT AUDIO OUT SS Red line 12V OUT A INPUT A V Cable interface definition A V input is a 4 pin female connector 4CH machine has 4 A V inputs 8CH A V INPUT VIN1 VINA machine has 8 A V inputs Feet 1 is for 12V power input feet 2 is for GND feet 3 is for audio input and feet 4 is for video input A N output is a 4 pin male connector feet 1 is for 12V power input feet 2 A N OUTPUT AV OUT NN dd is for GND feet 3 is for audio input and feet 4 is for video input WITNE S S SVC400P SVC800P Installation Manual 9 2 Specifications for the SENSOR BOX sensor inputs and outputs SENSOR OUTI SENSOR 0UT2 SENSORs 1 6 are the inputs for I O sensors SENSOR OUT is for sensor output connection SPEED and SPEND are for speed sensor which connect to the speed
3. pulse of the vehicle Firstly follow the steps of GUI SETUP EVENT SENSOR then enable the sensor switch and make sure the alarm switch is ON as shown below SENSOR F DOOR R DOOR BRAKE LEFT RIGHT RED WA NEXT PAGE SAVE The MDVR has 6 Alarm inputs and 2 Alarm outputs All alarm inputs are I O PWL which can reflect various vehicle statuses such as braking turning left etc A schematic diagram of the alarm input braking is shown below when the brake is applied the MDVR will detect the I O PWL the alarm LED will light up or flash and will record this event WITNE S S SVC400P SVC800P Installation Manual Stoplight 24V a gt Connect to MDVR S sensor input All alarm outputs are PWL outputs drive ability is 200MA and the voltage is 12V if you need more than that please connect to an external relay An alarm output photoelectric wiring diagram is as follows MDVR S Alarm output 9 3 Specifications for 485 and 232 serial ports There are two 485 serial ports and two 232 serial ports the functions are the same These serial ports can connect to accessories purchased from Shenzhen Streaming Video Technology such as the inertia sensor acceleration control panel PTZ station announcement and the card reader etc Please Note 485A means 485 485B means 485 SETUP gt PERIPHERAL gt EXT COM SETUP MODE There are STANDARD and BUS MODE two options when selec
4. F M Y 55 c OFF OFF M 2 5 5 G X 00 000 Y 00 000 CHECK After installing the inertia sensor make sure that the ENABLE switch is turned on Then press CHECK to verify its current values all the values will be defaulted to O 12 HDD INSTALLATION Open the lock with the key in fittings box remove the HDD box and screws and then open the box as the picture below Install the foam pad on both sides Since there is no screw here we are use rubber cover and foam pad asa vibration absorber One side of the box is a blue foam pad the other side is two yellow foam pads Put the rubber cover on both sides of the SATA HDD the side with a rubber band should be near to the circuit board Connect the cable please make sure the data cable is connected properly Put the cover back on and then refit the screws Please Note Please lock the HDD after successfully installing the HDD otherwise the MDVR will not start up 11 W T N F SS SVC400P SVC800P Installation Manual t Install the vibration absorber foam HDD installation 13 SIM CARD INSTALLATION When the device has built in 3G wireless module that support the wireless network communication the user will need to install the a SIM Card as detailed in the image above Remove the HDD box and the SIM Card cover Carefully insert the SIM card in place re attach the SIM Card cover and place the screws and HDD box back as normal ensuring that yo
5. LLATION TOOLS Please ensure that you have the following tools available prior to commencing an installation Drill and bids Screws bolts and vibration dampening washers as appropriate for mounting Wire cutters and wire connectors Test for voltage and electric current le W T N S S SVC400P SVC800P Installation Manual 7 INSTALLATION INSTRUCTIONS Follow these guidelines when installing MDVR s Unpack all components provided in the package Disconnect any source of power supply and or devices Locate a proper spot to install the SVAAOOL and install a built in vibration absorber if required Locate a reliable electrical ground point in the vehicle All wires and connections should be gathered to the back of SVA400L Connect to a power source and turn on the vehicle ignition to test the unit Observe completion of the unit power up procedures as described in section labelled as System Startup and Shutdown Meet all legal requirements for installing and or operating a video surveillance such as labelling all the essential information on the MDVR Video surveillance statues vary across nations please abide to the local statues 8 CONNECTING THE POWER FOR THE MDVR S Wire Description Positive wire Should be connected to Positive Input Red the positive terminal of the battery DC 12V Negative ground wire Should be GND Input Black connected to the negative terminal of the
6. and efficiently The powerful CMS software provides o Remote Monitoring o GPS Locations Local Recording Remote Downloading e Alarm Report System Additionally the MDVR s CMS is set up to provide automatic services for the protection of its data such as recovery data monitoring and backup for all its critical data 2 PRODUCT OVERVIEW Front View e UC 14 maoOu RA Definition for LED and connector on front panel ERE SS RN NET For displaying the network status POWER For power when the MDVR is powered the LED will be lit HDD If the MDVR install HDD is working fine The LED will be lit ERR If the MDVR has errors such as no HDD the LED will be lit ALARM If the MDVR has triggered an alarm the LED will flash aa VLOSS It will flash if video loss happens e W T N S S SVC400P SVC800P Installation Manual iRreceiver OR For receive the signal of remote control System Information DEBUG Testing series port for MDVR device USB Interface USB2 0 USB2 0 for record files back up or firmware update Need to lock the HDD case before boot up the MDVR Otherwise the Lock LOCK MDVR can not boot up When the MDVR is working unlock the HDD case and then MDVR will standby Rear View 49 Wee EM NNNM NENNEN NN WI FI ANT connector WI FI For connecting the WIFI ANT G GPS ANT connector For connecting the GPS ANT 3G EDGE GPRS ANT EDGE For connecting the 3G EDGE GPRS ANT connector DC8 48V For con
7. attery over time if the ignition is not turned off Connection Connect only to appropriate power supply and ensure proper grounding of the circuit Moisture Protect unit and connections from environmental sources of moisture and liquid spills Temp Do not install where unit temperature will exceed F140 F 60 C fall below 20 F 28 C or store the unit where temperatures rise above 175 F 80 C Avoid direct exposure to sunlight Ventilation Provide sufficient ventilation with a minimum of 6 inches cooling clearance to ensure proper operating temperature for the unit Vibration If necessary provide additional shock mounting to prevent damage and wear by excessive vibration Clearance Front clearance of 8 inch is required to slide the recording module from the mounting assembly Wiring Install where mounting assembly wires have sufficient clearance and will not be crimped or subject to wire insulation damages due to vibration A Access Secure the MDVR so that passengers or drivers cannot tamper or damage the unit cameras wires or other accessories Do not mount where access to any other vehicle component will be restricted Injury Install the unit cameras accessories and wires so that no injuries can be caused through impact with equipment during vehicle operation Ensure that all transportation regulations are followed to avoid passenger injury should they come in contact with the installed equipment 6 INSTA
8. necting power input Network port RJ45 Network port to make sure the MDVR can go online A V input and output and alarm output A V Integrated input A Power supply for camera I O Input and Output I O sensor input and output EXTEND Interface EXTEND For extend function such as RS485 and RS232 serials port e W T SS SVC400P SVC800P Installation Manual 3 DIMENSIONS e W T N F S S SVC400P SVC800P Installation Manual 4 PACKAGE CONTENTS Please ensure that the SVC400P SCV800P s box includes the following items MDVR s Recording Module and Mounting Assembly Video Input AV output cable Powercable USB Cable Screws for installing the unit A set of keys for locking and or unlocking the HDD case and a fuse Handheld IR remote control batteries not included Installation bracket Accessories available for the SVC400P SCV800P include the following Alarm Input Box SVA400A GPS Module and Antenna SVAAOOG 3G Module SVAAOOT Wifi Module SVA480W Din Plug to BNC Socket Adapter SVA480C Locking Box SVA400L 5 MOUNTING AND ENVIRONMENTAL REQUIREMENTS To ensure the MDVR operates efficiently and within the product warranty compliance please adhere to all following installation instructions Power It is recommended that the MDVR be connected to the vehicle ignition Battery power is used only when the vehicle is running The MDVR could drain any vehicle b
9. t standard mode you can select each external port for each COM when select Bus mode COM1 is station announcement COM2 is amplifier board unchangeable COM3 and COMA is changeable Please Note COM1 means 232RXD 1 COM2 means 232RXD 2 COM3 Means 485 1 COM3 Means 485 2 PTZ is recommended connect to COM3 or COMA WITNE S S SVC400P SVC800P Installation Manual EXT COM SETUP STANDARD BUS MODE M CONTROL PANEL ACCELERATION PTZ LED SCTEEN 10 WORKING STATUS nus a Va HDD 30 0 o O EJ ER i W M C 14 maoOruw R When device started up please check the LED HTR is ON means device has built in heater POWER is ON means the power is normal ERR is ON means there is no HDD or some other hardware errors NET is ON means the net module is normal VIDEO LOSS is ON means there is video loss if all the LED always flashing and no live view that means there is something wrong with MDVR please contact with the sales Please Note when MDVR has started up and only POWER LED is on and no live view output please make sure you have locked the HDD box 10 WITNE S S SVC400P SVC800P Installation Manual 11 INTERTIAL SENSOR CONNECTION If the MDVR s is connected to the inertial sensor then you track its features in the unit s Graphical User Interface GUI as following SYSTEM gt SENSOR gt ACCELERATION and then press check ACCELERATION NAME OSD EN THRESHOLD ALARM LOCK X 55 G OVERSHOCK SHK OF
10. u have connected the 3G antenna Follow the steps of GUI gt SETUP gt NETWORK gt MOBILE NETWORK select the mode type for the wireless module you have got as well as APN and the access number The device will restart after all these have been setup 12 W T N S S SVC400P SVC800P Installation Manual MOBILE NETWORK DE TYPE Ted p V L i gt FY G 1 IV1P Check the setup status Wireless module User name Password APN Access number CDMA card card BISI EVDO card card BTTT WCDMA Check with SIM card manufacture gos GPRS Check with SIM card manufacture 9918 EDGE Check with SIM card manufacture 9918 Finally we can check the status of the SIM card by pressing ENTER in the live view after unit has restarted You will find the status information for unit see the screen below which includes signal network dial up status and CMS connection status ALARM VL GPS NORMAL WIFI 95DB TEMPERATURE 84F VOLTAGE 12 5V ACCELERATION INVALID STREAMING 9999 FIRMWARE X3 4 V000021 MCU X3 4 0541 MCU T033101 HEATER ON IGNITION ON SPEED 000MPH DIRECTION NW SIM CARD OFF NETWORK NO SERVER DIAL UP UNKNOW SIGNAL 0 3G NETWORK STATUS CONNECT FAILED WIFI NETWORK STATUS CONNECT FAILED 13
Download Pdf Manuals
Related Search