Wallmount Vac 3.5 Gallon
Contents
1. ON O OFF NOTE MANY MORE USEFUL TOOLS ARE AVAILABLE AT YOUR LOCAL DEALER OR SHOP VAC WEBSITE dirt or rinse from the inside of the filter with water dry completely approximately 24 hours and re install Figures 13 amp 14 Note If the filter has been used for wet pick up it must be cleaned and dried before using for dry pick up MOUNTING INSTRUCTIONS Wall Bracket Installation 1 Select mounting location at a wall stud and or provide a minimum 8 wide x 12 high x 34 thick surface which is strong enough to hold the weight of the vacuum unit with a full tank of debris WARNING INADEQUATE MOUNTING COULD ALLOW THE UNIT TO FALL CAUSING INJURY AND OR DAMAGE TO THE UNIT 2 Secure wall bracket to mounting surface with 3 screws provided or other suitable fastener NOTE The screws provided are adequate ONLY for mounting into wood Be sure to use the proper suitable fasteners for mounting vacuum to a surface other than wood Make sure bracket is level Figure 2 3 The tool bag hook can be mounted on the wall in close proximity to the vacuum Secure with screws provided Hang tool bag onto hook using loop in back of tool bag Figure 3 INSTALLING THE DISPOSABLE FILTER BAG Not Standard with All Models 1 Use for dry pick up only Use in conjunction with cartridge filter for picking 15 Attach Vac up soot cement plaster or drywall dust m 1 Grasp top handle with one hand and plac2. 2 Grasp top handle with one hand and place other hand under front of tank 3 Pull upward until vacuum detaches from bracket Figure 7 Remove ALL dirt and debris found in tank The vacuum requires only a minimum of conversion when going from dry to wet pick up Remove all dry use filters from the vacuum A clean cartridge filter may be used for vacuuming small amounts of liquids For best results when vacuuming large quantities of liquid remove the cartridge filter When vacuuming liquids containing debris it is recommended purchasing a foam sleeve and install over filter cage otherwise a foam sleeve is not required for wet pick up Foam sleeve and additional filters may be purchased by visiting our website at www shopvac com contacting our customer service department or purchasing at your local Shop Vac distributor Misting in exhaust air may occur if the filter becomes saturated during wet pick up If misting occurs remove filter and allow to dry or replace with another dry filter to eliminate the misting and possible dripping of liquid around the lid Turn the unit off immediately upon completing a wet pick up job or when tank is full and ready to be emptied Raise the hose to drain any excess liquid into D RY D C K U P the tank The interior of the tank should be periodically cleaned Installing Foam Sleeve Not standard with all models A WARN N G ALWAYS DISCONNECT THE PLUG FROM THE 4 With tank cover in an upside down posit
3. Keep cord away from heated surfaces 7 Do not unplug by pulling on cord To unplug grasp the plug not the cord 8 Do not handle plug or appliance with wet hands 9 Do not put any object into openings Do not use with any openings blocked keep free of dust lint hair and anything that may reduce air flow 10 Keep hair loose clothing fingers and all parts of body away from openings and moving parts 11 Do not pick up anything that is burning or smoking such as cigarettes matches or hot ashes 12 Do not use without dust bag and or filters in place 13 Turn off all controls before unplugging SAVE THESE INSTRUCTIONS 14 Use extra care when cleaning on stairs 15 Do not use to pick up flammable or combustible liquids such as gasoline or use in areas where they may be present 16 Do not use your cleaner as a sprayer of flammable liquids such as oil base paints lacquers household cleaners etc 17 Do not vacuum toxic carcinogenic combustible or other hazardous materials such as asbestos arsenic barium beryllium lead pesticides or other health endangering materials Specially designed units are available for these purposes 18 Do not pick up soot cement plaster or drywall dust without cartridge filter and collection filter bag in place These are very fine particles that may pass through the foam and affect the performance of the motor or be exhausted back into the air Additional collection filter bags are availabl
4. amp 10 To remove the filter for cleaning again hold the 2 Hold the tank cover and turn the filter retainer counterclockwise to loosen and remove Figure tank cover and turn the filter retainer counter clockwise to loosen and remove slide the cartridge 19 filter off the lid cage Figures 11 amp 12 To clean the cartridge filter shake or brush off excess 3 Remove foam sleeve by sliding it up and off the lid cage 4 Shake excess dust off foam sleeve with a rapid up and down movement 5 Hold foam sleeve under running water for a minute or two rinsing from the inside A water wash is not always required depending on the condition of the foam sleeve 6 Gently wring out excess water blot foam sleeve with a clean towel and allow to dry The foam sleeve is now ready to be reinstalled on the lid cage NOTE WET PICK UP ACCESSORIES SHOULD BE WASHED PERIODICALLY ESPECIALLY AFTER PICKING UP WET STICKY KITCHEN ACCIDENTS THIS CAN BE ACCOMPLISHED WITH A WARM SOLUTION OF SOAP AND WATER EMPTYING LIQUID WASTES FROM THE TANK Your Wet Dry Vacuum may be emptied of liquid waste by removing the tank cover To empty stop the motor and remove the plug from the wall receptacle Remove the tank cover and deposit the liquid waste contents in a suitable drain After the tank is empty return the cover to its original position To continue use plug the cord into the wall receptacle and start the motor AUTOMATIC SUCTION SHUT OFF The vac
5. EQUIP MENT GROUNDING CONDUCTOR CAN RESULT IN A RISK OF ELEC TRIC SHOCK CHECK WITH A QUALIFIED ELECTRICIAN OR SERVICE PERSON IF YOU ARE IN DOUBT AS TO WHETHER THE OUTLET IS PROPERLY GROUNDED DO NOT MODIFY THE PLUG PROVIDED WITH THE APPLIANCE IF IT WILL NOT FIT THE OUTLET HAVE A PROPER OUTLET INSTALLED BY A QUALIFIED ELECTRICIAN This appliance is for use on a nominal 120 volt circuit and has a grounded plug that looks like the plug illustrated in sketch A A temporary adaptor that looks like the adaptor illustrated in sketches B and C may be used to connect this GROUNDING METHODS plug to a 2 pole receptacle as shown in sketch B if a properly grounded GROUNDED outlet is not available The een aan adaptor should be used only until a properly grounded outlet sketch A can be installed by a qualified electri cian The green colored rigid ear lug or the like extending from the adaptor must be connected to a permanent ground such as a properly grounded outlet box cover Whenever the adap tor is used it must be held in place by a metal screw IN CANADA THE USE OF A TEMPORARY ADAPTOR IS NOT PERMITTED BY THE CANADIAN ELECTRICAL CODE Make sure that the appliance is connected to an outlet having the same configuration as the plug No adapter should be used with this appliance a ADAPTER J METAL a SCREW ies 11 TAB FOR GROUNDING SCREW GROUNDED OUTLET BOX A B GROUNDING PIN EXTENSION CORDS Whe
6. Thanks for shopping with Improvements 1 Wallmount Vac 3 5 Gallon Item 410497 If you have any questions regarding this product cal IM P ROVEM EN TS 1 800 642 2112 and ask for our product specialists for your home inside and out Mon Fri 9 00 5 00 EST or e mail To order call productspecialist improvementscatalog com 1 800 642 2112 See many more products on the Internet West Chester OH 45069 www ImprovementsCatalog com IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance basic precautions should always be followed including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE A WARNING TO REDUCE THE RISK OF FIRE ELECTRIC SHOCK OR INJURY Do not leave appliance when plugged in Unplug from outlet when not in use and before servic ing Connect to a properly grounded outlet only See Grounding Instructions l 2 Do not expose to rain store indoors 3 Do not allow to be used as a toy Close attention is necessary when used by or near children 4 Use only as described in this manual Use only Manufacturer s recommended attachments 5 Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water contact Shop Vac Corporation for assistance 6 Do Not pull or carry by cord use cord as a handle close a door on cord or pull cord around sharp edges or corners Do not run appliance over cord
7. e 19 Do not leave the cord lying on the floor once you have finished the cleaning job It can become a tripping hazard 20 Use special care when emptying heavily loaded tanks 21 To avoid spontaneous combustion empty tank after each use 22 The operation of a utility vac can result in foreign objects being blown into eyes which can result in eye damage Always wear safety goggles when operating vacuum 23 STAY ALERT Watch what you are doing and use common sense Do not use vacuum cleaner when you are tired distracted or under the influence of drugs alcohol or medication causing diminished control 24 WARNING Do NOT use this vacuum cleaner to vacuum lead paint debris because this may disperse fine lead particles into the air This vacuum cleaner is not intended for use under EPA Regulation 40 CFR Part 745 for lead paint material cleanup A WARNING DO NOT LEAVE VACUUM UNATTENDED WHEN IT IS PLUGGED IN AND OR OPERATING UNPLUG UNIT WHEN NOT IN USE GROUNDING INSTRUCTIONS This appliance must be grounded If it should malfunction or breakdown grounding provides a path of least resistance for electric current to reduce the risk of electric shock This appliance is equipped with a cord having an equipment grounding conductor and grounding plug The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances A WARNING IMPROPER CONNECTION OF THE
8. e other hand under front of tank 2 With cord disconnected from receptacle remove tank cover 2 Align tab on back of vacuum located near top of tank to engage with slot in center of wall 3 Grasp cardboard collar firmly and slide rubber guard onto inlet fitting as bracket as vacuum is lowered into bracket Figure 4 far as possible Figure 15 3 Push downward making sure slots on vacuum located near the bottom of the tank attach to 4 When secured in place expand bag and position around the inside of the the tabs located at bottom of bracket Figure 5 tank 4 Lower top handle on vacuum to lay flat on top of housing This will secure unit in bracket WARNING FOR FINE DUST amp POWDERS When vacuuming fine dust or powders of any kind ex plaster drywall dust cold ashes concrete dust etc a high efficiency drywall filter bag must be used When vacuuming normal house hold dust and debris standard household disposable filter bags may be used These large bag filters connect to the air inlet fitting on the inside of the vacuum tank FILTER SELECTION GUIDE 90107 REUSABLE DRY FILTER AND MOUNTING RING SIZE deeb Fenech fits most Shop Vac Wet Dry Vacuums 3 5 U S Gal 13 2L N A 91931 f 90585 FOAM FILTER SLEEVE fits most Shop Vac Wet Dry 5 U S Gal 18 9L N A 91932 O Vacuums Detach Vac 1 Push release lever on bracket with thumb while moving top handle on vacuum to the up posi en Fe WET PICK UP OPERATION
9. ght fit nozzles hose etc Check that tank cover is sealed properly Obstruction in hose Check nozzle hose etc for obstructions and or nozzle remove if present Misting in the Saturated filter Replace saturated filter with a dry filter exhaust air A WARNING IF ANY OF THE MOTOR HOUSING PARTS SHOULD BECOME DETACHED OR BROKEN EXPOSING THE MOTOR OR ANY OTHER ELECTRICAL COMPONENTS OPERATION SHOULD BE DISCONTINUED IMMEDIATELY TO AVOID PERSONAL INJURY OR FURTHER DAMAGE TO THE VACUUM REPAIRS SHOULD BE MADE BEFORE REUSING THE VACUUM Trouble Suction weakens or cleaner runs hot THREE YEAR HOME USE WARRANTY Your Shop Vac vacuum cleaner is warranted for normal household use in accordance with the User Manual against original defects in material and workmanship for a period of three years from date of purchase Should this product be used for commercial or rental use a 90 day limited warranty will apply Shop Vac Corporation warrants placing this vacuum cleaner in correct operating condition by repair or parts replacement during the warranty period without charge This warranty does not cover accessories Use of non recommended filters and or accessories may void the manufacturer s warranty Shop Vac assumes no responsibility for damage or faulty performance caused by misuse careless handling and where repairs or modifications have been made Do not attempt to service your vacuum beyond that described in the User Manual P
10. ion slide foam sleeve down over lid cage until foam WALL OUTLET BEFORE REMOVING THE TANK COVER sleeve completely covers lid cage Figure 16 2 Place filter retainer into top of foam sleeve Figure 17 3 Hold the tank cover with one hand turn the handle on the filter retainer clockwise to tighten A CAUTION KEEP FILTERS CLEAN locking the filter into place Figure 18 EFFICIENCY OF THE VACUUM IS LARGELY DEPENDENT ON THE FILTER A CLOGGED FILTER CAN CAUSE OVERHEATING AND POSSIBLY DAMAGE THE CLEANER CHECK THE FILTER PERIODICALLY AND REPLACE AS REQUIRED INSTALLING THE CARTRIDGE FILTER Not standard with all models The cartridge filter can be used for wet or dry pick up installation is the same for both Use the cartridge filter in position over the lid cage for most general dry material pick up With the tank Cleaning Foam Sleeve 18 lt gt lt gt 16 p cover in an upside down position slide the cartridge filter down over the lid cage pushing until Not standard with all models the filter seals against the cover Figure 8 Place filter retainer into the top of the cartridge filter 1 The foam sleeve should be cleaned periodically Always disconnect the plug from the wall hold the tank cover with one hand turn the handle on the filter retainer clockwise to tighten receptacle before removing the tank cover Place tank cover in an upside down position locking the filter into place Figures 9
11. n using the appliance at a distance where an extension cord becomes necessary a 3 conductor grounding cord of adequate size must be used for safety and to prevent loss of power and overheating Use the table below to determine A W G wire size required To determine ampere rating of your vacuum refer to nameplate located on rear of motor cover Before using appliance inspect power cord for loose or exposed wires and damaged insulation Make any needed repairs or replacements before using your appliance Use only three wire outdoor exten sion cords which have three prong grounding type plugs and three pole receptacles which accept the extension cord s plug When vacuuming liquids be sure the extension cord connection does not come in contact with the liquid NOTE STATIC SHOCKS ARE COMMON IN DRY AREAS OR WHEN THE RELATIVE HUMIDITY OF THE AIR IS LOW THIS IS ONLY TEMPORARY AND DOES NOT AFFECT THE USE OF THE APPLI ANCE TO REDUCE THE FREQUENCY OF STATIC SHOCKS IN YOUR HOME THE BEST REMEDY IS TO ADD MOISTURE TO THE AIR WITH A CONSOLE OR INSTALLED HUMIDIFIER UNPACKING AND SET UP 1 Remove the tank cover by pushing in the side lugs with thumbs and lifting up on the tabs of the tank cover 2 Remove any accessories and paperwork which may have been shipped in the tank 3 Before replacing tank cover refer to Dry Pick Up or Wet Pick Up Operation in this manual to ensure you have the proper filters installed for your cleaning operation 4 Re
12. place tank cover on the tank by aligning tabs with lugs Press down firmly on the upper housing until tank cover snaps into place Refer to mounting instructions in this manual to attach your unit to wall 6 Attach hose to inlet located on side of tank following the instructions that apply to your specific unit For 3 5 gallon Grasp curved hose end and position open end over inlet with long portion pointing upwards Push hose end into inlet as firmly as possible making sure o1 Total length of cord in feet 120V Ampere Rating More Not More Than Than 14 12 12 Not recommended notch on hose end lines up with tab on inlet Turn hose end until it is pointing towards bottom of tank For 5 gallon Position non threaded end of elbow over inlet with threaded end pointing upwards Push elbow into inlet as firmly as possible making sure notch on elbow lines up with tab on inlet Turn elbow until threaded part of elbow is pointing towards bottom of tank Insert long machine hose end with locking nut into end of elbow and tighten Do not over tighten 7 Attach the extension wands not standard with all models to the accessory end of the hose Twist slightly to tighten the connection Figure 1 8 Attach one of the cleaning accessories depending on your cleaning requirements on the exten sion wands Twist slightly to tighten the connection Figure 1 9 Plug the cord into the wall outlet Your cleaner is ready for use
13. roof of purchase date is required The warranty gives you specific legal rights and you may have other rights which vary from state to state or province to province This warranty is void outside of the United States and Canada Customers in the United States for product service contact Shop Vac Corporation Customer Service at 570 326 3557 or go to www shopvac com support Visit www shopvac com for your vacuum s parts list schematic Customers in Canada for product service return the complete unit transportation prepaid to the Authorized Shop Vac Service Center nearest you Visit www shopvac ca for a complete list of Authorized Service Centers in you area Customers in Mexico for product service see paperwork that came with your unit
14. uum is equipped with an automatic suction shut off that operates when picking up liq uids As the level of the liquid rises in the tank an internal float rises until it seats itself against a seal at the intake of the motor shutting off suction When this happens the motor will develop a higher than normal pitch noise and the suction is drastically reduced If this occurs turn unit off immediately Failure to turn unit off after float rises and shuts off suction will result in extensive damage to the motor To continue use empty the liquid waste from the tank as outlined in the previous paragraph NOTE IF ACCIDENTALLY TIPPED OVER THE VACUUM COULD LOSE SUCTION IF THIS OCCURS TURN UNIT OFF AND PLACE VAC IN UPRIGHT POSITION THIS WILL ALLOW THE FLOAT TO RETURN TO ITS NORMAL POSITION AND YOU WILL BE ABLE TO CONTINUE OPERATION LUBRICATION No lubrication is necessary as the motor is equipped with lifetime lubricated bearings STORAGE Before storing your vacuum the tank should be emptied and cleaned The power cord can be wrapped around the cord wraps provided on the tank cover on front of vacuum Figure 20 The hose may be wrapped around the wall bracket and the accessories stored in the tool bag so they can be readily available Figure 21 The vacuum should be stored indoors TROUBLESHOOTING Possible Cause Remedy Clogged filter Brush dirt from filter If condition continues change filter Air leak Check all fittings for ti
Download Pdf Manuals
Related Search