KW5212 Wireless VDSL2 Router User Manual
Contents
1. From LAN Configure the DSL Router s IP Address and Subnet Mask for LAN interface In this page you can use DHCP Dynamic Host Configuration Protocol to control the assignment of IP addresses on your local network LAN only KW5212 support IPv4 Configure the Broadband Router IP Address and Subnet Mask for LAN interface GroupName IP Address 192 168 1 1 Subnet Mask 255 255 255 0 0 O 00 Enable IGMP Snooping Standard Mode Blocking Mode Enable LAN side firewall Disable DHCP Server Enable DHCP Server Start IP Address 192 168 1 2 End 1P Address 192 168 1 254 Static IP Lease List A maximum 32 entries can be configured MAC Address IP Address Remove Add Entries Remove Entries Enable DHCP Server Relay DHCP Server IP Address ss 25 WLAN VDSL Router Item IP address Subnet mask Enable IGMP snooping Disable Enable DHCP server Start end IP address Lease time Enable DHCP server relay Configure the second IP address and User Manual Description This is the IP address that other devices on your local network will use to connect to the modem This defines the size of your network The default 1s 255 255 255 0 IGMP Snooping is a method that actually snoops or inspects IGMP traffic on a switch When enabled the switch will watch for IGMP messages passed between a host and a router and will add the necessary ports to its multicast tab2. Scheduler Algorithm the QoS Scheduler Algorithm SP Strict Priority or WFQ Weight Fair Queuing Precedence the priority identification Weight the weight value 1 63 the highest is 63 PTM Priority the PTM priority normal or high Enable check the enable check box then press Enable to activate the queue If you want to disable this queue you can uncheck the corresponding check box and press Enable the queue will be disabled To add a queue click the Add button you will see the following page QoS Queue Configuration This screen allows you to configure a QoS queue and add it to a selected layer interface Name y Enable a Interface Queue Precedence d lower value higher priority The precedence list shows OTe eduler algorithm for each precedence level Queues of equal precedence will be scheduled based on the algorithm Queues of unequal precedence will be scheduled based on SP Input a queue name as you want and select a interface depending your need decide the priority of the interface lower value higher priority click apply save button lt gt QoS Classification Setup You can add or remove a rule QoS Classification Setup maximum 32 rules can be configured To add a rule click the Add button To remove rules check their remove checkboxes then dick the Remove button The Enable button will scan through every rules in the table Rules with enable checkbox checked will b
3. Bridge PPPoE Frames Between WAN and Local Ports Multicast Proxy C Enable IGMP Multicast Proxy C No Multicast VLAN Filter PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter Authentication method is default to Auto It is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to Enable Full Cone NAT In full cone NAT all requests from the same private IP address and port are mapped to the same public source IP address and port Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device 12 WLAN VDSL Router User Manual The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute and 4320 minutes Use Static IPv4 address If the ISP gave you a static fixed IP address select this option and enter 1t in the IP Address field If the ISP did not give you a static IP address clear the Use Static IP Address option The ISP automatically assigns the WAN connection an IP address when it connects Enable PPP Debug Mode Select this to turn on the debug mode for the
4. Country Drop down menu that allows selection of specific channel f 5 5 2 Security This page allows you to configure security features of the wireless LAN interface You may set up configuration manually or through WiFi Protected Setup WPS 1 Click Security of Wireless item and you ll see the following page Enable Wireless Hide Access Point C Clients Isolation Disable WMM Advertise C Enable Wireless Multicast Forwarding WMF SSID WLAND75565 BSSID 00 0E F4 D7 55 66 Country UNITED STATES Max Clients 16 Wireless Guest Virtual Access Points Enable Max O Soa e WM WMF Clients 7 5 a n BSSID 2 Configure WPA Pre shared key as below and click Apply Save 28 WLAN VDSL Router User Manual WPS Setup Enable WPS Disabled w Manual Setup AP You can set the network authentication method selecting data encryption specify whether a network key is required to authenticate to this wireless ne Click Apply Save when done Select SSID WLANDT5565 w Network Authentication WEP Encryption Disabled w Apply Save 3 Enable WPS as below click Save Apply WPS Setup Enable WPS Enabled w Add Client This feature is available only when WPA PSK WPS1 WPA2 PSK or OPEN mode is configured Enter STA PIN Use AP PIN Add Enrollee Set WPS AP Mode Configured Setup AP Configure all security settings with an external registar Device PIN 168706
5. Option Description A checkbox that enables or disables the wireless LAN interfaces The default is to Enable wireless l o enable wireless communications Select Hide Access Point to protect the ADSL route access point from detection by wireless active scans If you do not want the access point to be automatically detected by a wireless station this checkbox should be deselected Hide Access The station will not discover this access point To connect a station to the access Point point the station must manually add this access point name in it s wireless configuration In Windows XP go to the Network gt Properties function to view all of the available access points You can also use other software programs such as NetStumbler to view available access points Clients Enable this item 1f you don t want your wireless clients to communicate with each isolation other Enter a name for user s wireless network here SSID stands for Service Set Network name Identifier This name must be between 1 and 32 characters long The default name is 27 WLAN VDSL Router User Manual SSID KASDAxxxx xxxx means the mac address of KW5212 with uppercase and without colon All wireless clients must either detect the gateway or be configured with the correct SSID to access the Internet BSSID Displays the gateway s wireless MAC address User may need this address if user 1s using WDS or multiple gateways Click Apply to save changes
6. hasda Networks with Innovation KW5212 Wireless VDSL Router User Manual Kasda Networks Inc AMIA IG ABU A BR ZS E WLAN VDSL Router User Manual NOTICE This document contains proprietary information protected by copyright and this Manual and all the accompanying hardware software and documentation are copyrighted All rights are reserved No part of this document may be photocopied or reproduced by mechanical electronic or other means in any form The manufacturer does not warrant that the hardware will work properly in all environments and applications and makes no warranty or representation either expressed or implied with respect to the quality performance merchantability or fitness for a particular purpose of the software or documentation The manufacturer reserves the right to make changes to the hardware software and documentation without obligation to notify any person or organization of the revision or change All brand and product names are the trademarks of their respective owners Copyright 2014 All rights reserved WLAN VDSL Router User Manual Content I ORV M o e OOO de de 1 1 1 NS A A A AN TESE EEA ANAE AE E 1 EEL o aa A E ca 1 ke2 VDE COMPAN oesi i A a AN 1 beloa A eas ai tee leh h alc 1 1 1 4 Network Protocol Features ni da 1 Los AFM CAPA IES A AAA AAA EA AI 2 ELG A A AP e O A EATA 2 Lie Management oppor sscan e Ee 3 LIS Operating Sy Steny Upa pon 3 LERES ra A tal bcos a a te
7. This option uses WPA2 with a pre shared key WPA2 and WPA This option supports WPA2 WPA encryption for devices capable of one or the other standard The gateway automatically detects whether a particular device can use WPA2 or WPA WPA2 AND WPA PSK This has WPA2 or WPA encryption based on client abilities as well as a pre shared key After making changes click Apply to save 5 4 Printer Server Installations 1 Click Advanced setup gt Print Server and then Check Enable on board printer server and key in Printer name Make and model Print Server settings This page allows you to enable disable printer support Enable on board print server Sawe Apply 2 Click on Add a printer from Control Panel of the Windows computer and click Next 31 WLAN VDSL Router User Manual Add Printer Wizard Welcome to the Add Printer Wizard This wizard helps you install a printer or make printer connections To continue click Next lt Back Cancel 3 Select Network Printer and click Next Add Printer Wizard Local or Network Printer ls the printer attached to your computer If the printer is directly attached to your computer click Local printer If itis attached to another computer or directly to the network click Network printer Local printer Y Automatically detect and install my Plug and Play printer Network printer lt Back Canc
8. IPv4 address If the ISP gave you a static fixed IP address select this option and enter it in the IP Address field If the ISP did not give you a static IP address clear the Use Static IP Address option The ISP automatically assigns the WAN connection an IP address when it connects Enable PPP Debug Mode Select this to turn on the debug mode for the PPP connection Bridge PPPoE Frames Between WAN and Local Ports In addition to the VDSL Device s built in PPPoE client you can enable this to pass PPPoE through in order to allow LAN hosts to use PPPoE client software on their computers to connect to the ISP via the VDSL Device Each host can have a separate account and a public WAN IP address PPPoE pass through is an alternative to NAT for applications where NAT is not appropriate Disable PPPoE pass through if you do not need to allow hosts on the LAN to use PPPoE client software on their computers to connect to the ISP The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires this setup do not select it If you need to select it the PPP IP Extension supports the following conditions It allows only one computer on the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to the computer s LAN interface through DHCP Only one system on the LAN can be connected to the
9. Jasa ao 41 WLAN VDSL Router User Manual QoS Classification Setup A maximum 32 entries can be configured Choose Add or Remove to configure network traffic classes F you disable WMM function in Wireless Page classification related to wireless will not take effects CLASSIFICATION CRITERIA CLASSIFICATION RESULTS na E HEE see aa meee 00 0e f4 23 45 12 100 23 22 23 22 22 erro renga PARL 1263 32 ow p AFLI upstream LAN F downstream 2 MIN 00 0c 12 13 11 11 13 36 25 11 8 192 1 68 1 23 2 RA Then in the Add Network Traffic Class Rule page enter the information to set up a rule to your needs To Assign Classification queue select the needed WAN queue Traffic Class Name Rule Order Rule Status Specify Classification Criteria A blank criterion indicates it is not used for classification Class Interface Ether Type Source MAC Address Source MAC Mask Destination MAC Address Destination MAC Mask Specify Classification Results ETHO WAN Last i Enable E PPPoE DISC oxeeaa 00 23 22 ae 12 22 fr if ff 00 00 00 12 11 11 21 a1 1a f f ff 00 00 00 Must select a classification queue A blank mark or tag value means no change Assign Classification Queue Mark Differentiated Service Code Point DSCP Mark 802 1p priority Tag VLAN 1D 0 4094 CLASSIFICATION CRITERIA pppikatnl kPathlkkerii hPres AFL2 0011003 Apply Save 3 Cl
10. and DNS server to the computer through DHCP using the LAN interface IP address The gateway extends the IP subnet at the remote service provider to the LAN computer That is the PC becomes a host belonging to the same IP subnet The ADSL gateway bridges the IP packets between WAN and LAN ports unless the packet 1s addressed to the gateway s LAN IP address 7 Select a preferred wan interface as the system default gateway Selected Default Available Routed WAN Gateway Interfaces Interfaces ppp 1 8 Get DNS server information from the selected WAN interface or enter static DNS server IP addresses If only a single PVC with IPoA or static MER protocol is configured you must enter static DNS server IP addresses 18 WLAN VDSL Router User Manual 2 Select DNS Server Interface from available WAN interfaces Selected DNS Server inter Available WAN Interfaces Interfaces Ppp 1 Use the following Static DNS IP address 9 Make sure that the settings below match the settings provided by your ISP Click on the Apply Save button to save your configurations Connection Type PPPOE NAT Ena bled Full Cone NAT Firewall IGMP Multicast Disabled Quality Of Service Enabled 5 2 3 Router Mode Setup 1 From Advanced Setup click Layer2 Interface and select ETH Interface Before you configure ETH WAN interface you d better remove all PVC settings from ATM interface ime Conn
11. beaten ete 3 1 2 PACKET CONTENTS aida 3 1 3 SYSTEM REQUIREMENTS c ccccesseccscccceccescescesceccacssccscesceccessescsesaecaecaceacsscsscessaesaecaecaceacers 3 1 4 FACTORY DEFAULTS ourn ll De dale oo 4 1 5 WARNINES AND CAUTION Sta idoiia 4 2 HARDWARE DESCRIPTION ae 5 3 HARDWARE INSTALDATIO Noia in 7 4 PC CONFIGURATION CUIDE cds 8 4 1 LOCAL PC CONFIGURATION IN WINDOWS 95 98 ME XP T ooooonnnnnnnccccnnccnncncnncnicicicinininon 8 4 2 LOCAL PC CONFIGURATION IN WINDOWS 2000 assi 8 5 WEB BASED MANAGEMENT GUIDE ooccocccnnncccnccnonoconaccnnnccnncconaccnnnconancnnaconacconaconannons 9 5 1 ED E PAG EE PETE E ETTE EEA EEE EAT ERTE eka oe 9 Dez INTERNE EP ACCESS CONPIGURA TIO Nit 10 LL ADS SEU A sad 10 A US A A Rano tousat nose ances atone 15 dio NOUter Mode Dec sss aren asa 19 1 AN ONO S sae a aoa E A 25 5 3 AHE A D N A E E EE A EETA A EEEE EEEE EETA E 27 O E A e EPET E EE ENE EEA NTE E E E N A EEEE 27 Dee DC CUTIE AA A O 28 5 4 PRINTER SERVER INSTALLATIONS ccccsccosccecccscccnccescesccenceescesecencecseusceesseescesecasseeseuascs 31 6 QOS Dr TUE OO 33 APPENDIX FREQUENT ASKED QUESTIONS cconcccnnicnnnonnnnonncnoncnnnancnonannconcnconcnnonancnnnanos 43 WLAN VDSL Router User Manual 1 Overview Thank you for choosing our product The product is a Wireless VDSL router combining an VDSL modem an 802 11n wireless router a 4 port switch and an USB port in one unit bringing high speed wireless Internet connection t
12. remote since the DHCP server within the ADSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this option is selected 23 WLAN VDSL Router User Manual The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address The gateway extends the IP subnet at the remote service provider to the LAN computer That is the PC becomes a host belonging to the same IP subnet The ADSL gateway bridges the IP packets between WAN and LAN ports unless the packet 1s addressed to the gateway s LAN IP address 9 Select WAN interface as the system default gateway Click Next Selected Default Available Routed WAN Gateway Interfaces Interfaces ppp 1 10 Get DNS server information from the selected WAN interface or enter static DNS server IP addresses Click Next Selected DNS Server Interfaces pppu 1 Use the following Static DNS IP address Secondary DNS server fo 24 Available WAN Interfaces WLAN VDSL Router User Manual 11 Make sure that the settings below match the settings provided by your ISP Click on the Apply Save button to save your configurations and reboot the ADSL router Connection Type PPPo MAT Enabled Ful Cone NAT Disabled Firewall Enabled IGMP Multicast Disabled Quality Of Service Enabled 5 2 4 LAN Settings IPv6 dual stack ul E
13. the format also should be xx xx xx Xx xx xx It is used to hide some information of the MAC address means needed and 0 means ignored For example MAC address e0 3b 4a c2 ca e2 and MAC mask ff ff ff 00 00 00 that is whatever MAC address while matches e0 3b 4a XX XX XX will be accepted Specify Classification Results Enter or select appropriate parameters you want for the packets matched the above classification criteria in the following fields You have to choose a classification queue A blank mark or tag value means no change Specify Classification Queue assign classification queue from the drop down box If you want to select the queue you should make sure the specific queue 1s enabled in Queue Config section Mark Differentiated Service Code Point DSCP select the DSCP you want to be the new DSCP for the packets which matched the above classification criteria Mark 802 1p priority it is a LAN Layer 2 QoS CoS Protocol for Traffic Prioritization It is interoperable with IEEE 802 1Q 802 1p has 8 kinds of priority Note 802 1p vlan tag feature be supported only when in bridge mode DSL WAN interface gt IPQoS o LAN to WAN IP QoS 1 It is a QoS controlling the traffic from LAN to WAN So first make sure there is at least one WAN queue If you have configured WAN interface and it will appeared as a default queue you can also add other queues of the specific interface See Queue Config Here we have
14. type 5 OAM F4 F5 Built in NAT MAC Filtering Packet Filtering Stateful Packet Inspection SPI Denial of Service Prevention DoS 2 WLAN VDSL Router 1 1 7 1 2 1 3 o DMZ Management Support Operating System Support Oo Web Based GUI User Manual O Upgrade or update via FTP HTTP O Command Line Interface via Telnet O Diagnostic Test O Firmware upgradeable for future feature enhancement eo WINDOWS 98 98 SE ME 2000 XP VISTA 7 O Macintosh o LINUX Environmental O Operating humidity 10 90 non condensing O Non operating storage humidity 5 95 non condensing Packet Contents The packet contents are as the following VDSL ROUTER External Splitter Power Adapter Telephone Line Ethernet Cable Antenna Base CD System Requirements Before using this ROUTER verify that you meet the following requirements x x x x x x 2 x x WLAN VDSL Router User Manual 1 4 1 5 Oo Subscription for ADSL service Your ADSL service provider should provide you with at least one valid IP address static assignment or dynamic assignment via dial up connection O One or more computers each contains an Ethernet 10 100M Base T network interface card NIC O A hub or switch if you are connecting the device to more than one computer O For system configuration using the supplied web based program A web browser such as Internet Explorer v5 0 or later or Netsca
15. 35 Help 4 Now you can use a wireless adaptor with WPS function and the WPS button to connect KW5212 to access the Internet 5 To configure security features for the Wireless interface please open Security item from Wireless menu This web page offers nine authentication protocols for user to secure user s data while connecting to networks There are four selections including Open Shared 802 1X WPA WPA PSK WPA2 WPA2 PSK Mixed WPA WPA2 Mixed WPA WPA2 PSK Different item leads different web page settings Please read the following information carefully 29 WLAN VDSL Router User Manual The wireless security page allows user to configure the security features of user s wireless network Set WPS AP Mode Configured wW Setup AP Configure all security settings with an external registar Device PIN 16870635 Help Manual Setup AP You can set the network authentication method selecting data encryption specify whether a network key is required to authenticate to this wireless network and specify the encryption strength Click Apply Save when done Select SSID WLAND75565 ww Network Authentication WEP Encryption Disabled w Apply Save There are several security methods to choose from depending on user s needs and the capabilities of user s wireless machines Shared 802 1 WPA WPA PSE WPA WPA FSE Mixed WPA2 WPA Mixed WPA WPA FSE WEP open and WEP shared WEP is an encr
16. P address IP address range of the PC that you specify should meet the setting range in NAT rules 4 Central Office equipment may have problem 5 The country or the wireless network type you selected is wrong 43 WLAN VDSL Router User Manual Q PC cannot browse Internet web page A Please make sure DNS server appointed to the PC is correct You can use ping application program to test whether the PC can connect to the DNS server of the ADSL operator Q Initialization of the PVC connection failed A Be sure that cable is connected properly from the DSL port to the wall jack The DSL LED on the front panel of the ADSL router should be on Check that your VPI VCI type of encapsulation and type of multiplexing setting are the same as what you collected from your service provider Re configure ADSL router and reboot it If you still cannot work it out you may need to verify these variables with the service provider If the cause is not given above please contact your local service provider 44
17. PPP connection Bridge PPPoE Frames Between WAN and Local Ports In addition to the VDSL Device s built in PPPoE client you can enable this to pass PPPoE through in order to allow LAN hosts to use PPPoE client software on their computers to connect to the ISP via the VDSL Device Each host can have a separate account and a public WAN IP address PPPoE pass through is an alternative to NAT for applications where NAT is not appropriate Disable PPPoE pass through if you do not need to allow hosts on the LAN to use PPPoE client software on their computers to connect to the ISP The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires this setup do not select it If you need to select it the PPP IP Extension supports the following conditions It allows only one computer on the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to the computer s LAN interface through DHCP Only one system on the LAN can be connected to the remote since the DHCP server within the ADSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this option is selected The gateway becomes the default gateway and DNS server to the computer through DHCP using the LAN interface IP address The gateway extends the IP subnet at the remote service p
18. a atm0 WAN interface the interface has a default queue Make sure to enable the queue 37 WLAN VDSL Router User Manual Name Polen a om ty y wwe Jw oe 2 A jpe B wid SP 2 o ts AA ema gy O q E E o ad ye we foe foe ff Jest WMM Best Fal Effort E EJ wid o az Enabled Default Queue ES ES amo ose Patho 2 In QoS Classification Setup page Click Add to add a QoS Classification a QoS Classification Setup A maximum 32 entries can be configured Choose Add or Remove to configure network traffic classes F you disable WMM function in Wireless Page classification related to wireless will not take effects CLASSIFICATION CRITERIA CLASSIFICATION RESULTS O ee e et ht aan con ya Then in the appeared Add Network Traffic Class Rule page enter the information to set up a rule 1 Specify the rule name rule order and rule status Traffic Class Name upstrea m Rule Order Rule Status Last ka Enable e 2 Specify the classification criteria Here you can set every parameter to strictly control the specific traffic or you can set several parameters to let them be the key elements to control the traffic A blank criterion indicates it is not used for classification 38 WLAN VDSL Router User Manual Specify Classification Criteria A blank criterion indicates it is not used for classification Class Interface LAN a Ethe
19. and active DSL Green Quick Blinking DSL is trying to establish a connection Slow Blinking No DSL link On IP connected Blinking IP connected and IP traffic is passing thru INET Green i this device Off ADSL connnetion is not present WLAN VDSL Router User Manual Rear panel ETH4 ETH3 ETH2 ETH1 ON OFF POWER y Function Connect the device to an DSL telephone jack or splitter DSL using a RJ 11 telephone cable Connect the device to your PC s Ethernet port or to ETH1 2 3 4 the uplink port on your hub switch using a RJ 45 cable Connect the device to a printer ON OFF Switch it on or off POWER Connect to the supplied power adapter Side panel WIFI button Enable or disable wireless function Reset button System reset or reset to factory defaults WPS button A convenient way for WPS set WLAN VDSL Router User Manual 3 Hardware Installation This chapter shows you how to connect Router Meanwhile it introduces the appropriate environment for the Router and installation instructions 1 Using a telephone line to connect the DSL port of ROUTER to the MODEM port of the splitter and using a other telephone line connect your telephone to the PHONE port of the splitter then connect the wall phone jack to the LINE port of the splitter The splitter comes with three connectors as below LINE Connects to a wall phone jack RJ 11 jack MODEM Connects to the DSL jack of ROUTER PHONE Connects to a telep
20. ass Class Ether SrclP DstiP z DSCP 802 1P Queue DSCP 802 1P VlaniD _ Name or a an Se E A pga PTOS tt a oa Key ae Tag le 00 06 f4 23 45 12 100 23 22 23 22 22 1 A EEFIN FRA 192 168 1 12 12 03 23 22 ro h 80 ma 33 g o 39 WLAN VDSL Router User Manual eo WAN to LAN IP QoS 1 Here we take WAN to LAN ETH1 QoS for example Make sure there are enabled port ETH1 based queues here LAN queues need your configuration You can enable wireless to enable WMM queues by default or add ETHO ETH4 ported based queues manually ple jefe 2 In QoS Classification Setup page Click Add to add a Qos Classification QoS Classification Setup A maximum 32 entries can be configured Choose Add or Remove to configure network traffic classes Tf you disable WMM function in Wireless Page classification related to wireless will not take effects CLASSIFICATION CRITERIA CLASSIFICATION RESULTS Class E Class Ether a SrclP DstiP DSCP 802 1P Queue DSCP 802 1P VlaniD E oie pa mner SrcMAC Mask DstMAC Mask Prefilength Prefileng sco nt Da Check Key ws Mark Tag a ae OO Qe F4 23 45 12 00 23 22 23 22 22 upstream NS EEEN ERRE 192 168 1 12 12 63 23 22 oh 80 a 33 a Then in the Add Network Traffic Class Rule page enter the information to set up a rule Traffic Class Name downstream Rule Order Last Rule Status Enable Specify Classification Criteria A blank criterion indicates it is not used for class
21. ccasion After the configuration you need to click Apply Save WPL 0 255 o VCI 32 65535 Select OSL Latency Patho C Pathi Select DSL Link Type Eo4 is for PPPoE IPOE and Bridge Eo PPPoA IPoA Select Connection Mode Default Mode Single service over one connection VLAN MUX Mode Multiple lan service over one connection Encapsulation Mode LLC SNAP BRIDGING w service Category UBR Without PCR 3 Click WAN Service from the left menu WLAN VDSL Router User Manual Interface Description Type Vlan3021p vlanMuxld Igmp NAT Firewall Remove Edit 4 Click Add to select a layer 2 interface for this service and then click Next atmO 0 0 35 5 Choose WAN service type just choose PPPoE for example here You can enter your own service description here if you want and then click Next Select WAN service type PPP over Ethernet PPPOE O IP over Ethernet Bridging Enter Service Description pppoe_O_0 35 6 Input PPP Username amp PPP Password and then click Next The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password 11 WLAN VDSL Router User Manual PPP Username O PPP Password O Authentication Method AUTO We C Enable Fullcone NAT C Dial on demand with idle timeout timer PPP IP extension FP Use Static IPv4 Address Enable PPP Debug Mode
22. dle timeout timer PPP IP extension FP Use Static IPv4 Address O Enable PPP Debug Mode C Bridge PPPoE Frames Between WAN and Local Ports Multicast Proxy FP Enable IGMP Multicast Proxy C No Multicast VLAN Filter 16 WLAN VDSL Router User Manual PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter Authentication method is default to Auto It is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to Enable Full Cone NAT In full cone NAT all requests from the same private IP address and port are mapped to the same public source IP address and port Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute and 4320 minutes Use Static IPv4 address If the ISP gave you a static fixed IP address select this option and enter it in the IP Address field If the ISP did not give you a static IP address clear the Use Static IP Address option The ISP automatically assigns the WAN connection a
23. ds of assured forwarding services Each AF has three different packet loss priorities from high medium to low Also CS1 CS7 indicates the IP precedence Note Before configuring Queue config and QoS Classification section you must enable QoS function for the reason that the queues activation will depend on this the classification will also depend on this lt gt QoS queue setup QoS Queue Setup In ATM mode maximum 16 queues can be configured In PTM mode maximum 8 queues can be configured Device Info For each Ethernet interface maximum 3 queues can be configured Quick Setup To add a queue click the Add button To remove queues check their remove checkboxes then click the Remove button Advanced Setup The Enable button will scan through every queues in the table Queues with enable checkbox checked will be enabled Queues with enable checkbox un checked will be disabled Layer2 Interface The enable checkbox also shows status of the queue after page reload WAN Service Note that if WMM function is disabled in Wireless Page queues related to wireless will not take effects LAN a dd e Security Parental Control QoS Queue DNS UPnP l WMM Background wild 6 SP Enabled DNS Proxy Interface Grouping AECE UC e UC CIO IS AS ES E E E Certificate Multicast Add Enable Remove Name the queue name Key the item number 34 WLAN VDSL Router User Manual Interface the queue interface
24. e enabled Rules with enable checkbox un checked will be disabled The enable checkbox also shows status of the rule after page reload If you disable WMM function in Wireless Page Classification related to wireless will not take effects Ey CLASSIFICATION CRITERIA CLASSIFICATION RESULTS Class Class Ether SrcMAC DstMAC SrcIP DstIP DstPort ae ae 1P Queue 802 1P kbps Bo A Name Intf Type Mask Mask PrefixLength PrefixLength Key Mark Add I Enable Remove Click add button you will see the following page 35 WLAN VDSL Router User Manual This screen creates a traffic class rule to classify the ingress traffic into a priority queue and optionally mark the DSCP or Ethernet priority of the packet Click Apply Save to save and activate the rule Traffic Class Name Rule Order Rule Status Class Interface Ether Type Source MAC Address Source MAC Mask Destination MAC Address Destination MAC Mask Specify Classification Results A blank value indicates no operation Specify Class Queue Required Packets classified into a queue that exit through an interface for which the queue is not specified to exist will instead egress to the default queue on the interface Mark Differentiated Service Code Point DSCP Mark 802 1p priority Class non vlan packets egress to a non vlan interface will be tagged with VID 0 and the class rule p bits Class vlan packets egress to a non vlan interface will hav
25. e the packet p bits re marked by the class rule p bits No additional vian tag is added Class non vlan packets egress to a vlan interface will be tagged with the interface VID and the class rule p bits Class vlan packets egress to a vlan interface will be additionally tagged with the packet VID and the class rule p bits Set Rate Limit fe Kbits s Parameters Traffic Class Name Assign a name for this class to uniquely identify the others among multiple classes Rule Order Select the priority for this class rule Rule Status Select Enable to activate this class rule Specify Classification Criteria The following parameters are to be classification rule Enter or select appropriate parameters on the following fields A blank criterion indicates it is not used for classification Class Interface select the interface you want to be the one aspect of the classification criteria Here LAN and WAN can be viewed as IP QoS the others can be viewed as ported based QoS which means that control the QoS of certain port such For example if you select ETHO port then criteria applies to this port that is ported based QoS Entry Type select the application type Source destination MAC Address enter the source and destination MAC address as the QoS 36 WLAN VDSL Router User Manual Classification Criteria The format should be xx xx xx xx xx Xx Source destination MAC Mask MAC mask is similar to IP mask and
26. ection Mode Remove 2 Click Add and you ll see the following screen 19 WLAN VDSL Router User Manual ETH WAN Configuration This screen allows you to configure a ETH port Select a ETH port ethietht Apply Save 3 Select a ETH port as you will You can select ENET1 ENET2 ENET3 or ENET4 port as the WAN interface and Default mode as connection mode eth0 ethO e ethi etho ethl ethl eth2 eth2 eth3 eth3 4 Click Apply Save and you ll see the following screen Interface Name Connection Mode Remove eth2 eth2 VlanMuxMode Remove 5 From Advanced Setup click WAN Service to configure a WAN service over the interface you selected Interface Description Type vlan8021p VianMuxid Igmp NAT Firewall Remove Edit 6 Click Add and you ll see the following screen eth2 eth2 7 Click Next and you ll see the following screen Select PPPoE as WAN service type for example Click Next WLAN VDSL Router User Manual WAN Service Configuration Select WAN service type PPP over Ethernet PPPoE IP over Ethernet Bridging Enter Service Description pppoe_eth2 For tagged service enter valid 802 1P Priority and 802 10 VLAN ID For untagged service set 1 to both 802 1P Priority and 802 190 VLAN ID Enter 802 1P Priority 0 7 Enter 802 10 VLAN ID 0 4094 Network Protocal Selection IPV6 Only not support IP 4 Only 8 Enter the u
27. el 4 Select Connect to a printer on the Internet type http 192 168 1 1 631 printers printer and click Next The printer name Printer must be the same name entered in the ADSL router print server setting as in step 1 Add Printer Wizard Locate Your Printer How do you want to locate your printer If you don t know the name of the printer you can browse for one on the network What do you want to do Type the printer name or click Next to browse for a printer Name Connect to a printer on the Internet or on your intranet URL jan 92 168 1 1 631 printers printer Cancel 32 WLAN VDSL Router User Manual 5 Select driver file directory on CD ROM or in your hard disk and click OK 6 Choose Yes or No for default printer setting and click Next Add Printer Wizard Default Printer Your computer will always send documents to the default printer unless you specify otherwise Do you want your Windows based programs to use this printer as the default printer Yes C No lt Back Cancel 7 Click Finish Add Printer Wizard Completing the Add Printer Wizard You have successfully completed the Add Printer wizard You specified the following printer settings Name Printer on 192 168 1 1 Default Yes Location Comment To close this wizard click Finish lt Back Cancel 6 QoS setup QoS helps
28. hone set 2 Using an Ethernet Cable to connect the LAN port of the ROUTER to your LAN or a PC with network card installed 3 Connect the power cable to the PWR connector on ROUTER then plug in the power adapter to the power outlet and then press the on off button Connect Wireless unit with siot EEEE op A ee tae ee ae ETH4 ETH1 ON OFF POWER PD MINIPCI Notes Without the splitter and certain situation transient noise from telephone can interfere with the operation of the Router and the Router may introduce noise to the telephone line To prevent this from happening a small external splitter must be connected to each telephone WLAN VDSL Router User Manual 4 PC Configuration Guide 4 1 4 2 Local PC Configuration in Windows 95 98 ME XP 7 k In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network icon On the Configuration tab select the TCP IP network associated with your network card and then click Properties In the TCP IP Properties dialog box click the IP Address tab Set the IP address as 192 168 1 x x can be a decimal number from 2 to 254 like 192 168 1 2 and the subnet mask as 255 255 255 0 On the Gateway tab set a new gateway as 192 168 1 1 and then click Add Configure the DNS tab 1f necessary For information on the IP address of
29. ick Apply to save your settings and the added rule will be listed as below CLASSIFICATION RESUL ii A OC ag ann SEM Me a 00 De f4 23 45 12 00 23 22 23 22 22 ostream LAN 92 168 1 1 ow y e ARI AAA AA id wer ferro pl downstream WAN F 00 0c 12 1a 11 11 13 36 25 11 8 192 168 1 23 24 TCP 180 80 AF13 34 100 23 22 a8 12 22 112 11 11 21 a1 1a y H et i h Ll lis de diia FRAPS O0 00 00 FF FF ff 00 00 00 e ad y 7 WLAN VDSL Router User Manual Appendix Frequent Asked Questions Q A Q telep A gt gt gt None of the LEDs are on when you power on the ADSL router Please make sure what you use is the power adaptor attached with the ADSL router package and checks the connection between the AC power and ADSL router DSL LED does not turn on after connect telephone line Please make sure what you use is the standard telephone line as attached with the package make sure the line is connected correctly and check whether there is poor contact at each interface Wait for 30 seconds to allow the ADSL router establishes connection with you ADSL operator DSL LED is in the circulation of slow flashing and fast flashing after connecting hone line This situation means the ADSL router is in the status of failing to establish connection with Central Office Please check carefully and confirm whether the ADSL router has been installed correctly LAN LED does not turn on after co
30. ification Class Interface Ether Type IF 0x800 Source MAC Address 00 0c 12 1a 11 11 Source IP Address Mask 13 36 25 11 8 y lt E 4 Destination IP Address Mask 192 168 1 23 24 Differentiated Service Code Point DSCP Check Protocol ER e UDP TCP Source Port port or port port 80 UDP TCP Destination Port port or port port 80 Specify Classification Results Must select a classification queue A blank mark or tag value means no change Assign Classification Queue ethl keyidiPrel Mark Differentiated Service Code Point DSCP Apply Save 3 Click Apply to save your settings The added rule will be listed as below 40 WLAN VDSL Router User Manual QoS Classification Setup A maximum 32 entries can be configured Choose Add or Remove to configure network traffic classes Tf you disable WMM function in Wireless Page classification related to wireless will not take effects CLASSIFICATION CRITERIA CLASSIFICATION RESULTS MEE me Boe mine rion Le cc es IL waaa vo fe Wp fx oe domsten MAN P 00 0c 12 1a 11 11 13 36 25 11 8 192 168 1 23 24 A i gt Port based QoS Take port ETHO to WAN QoS for example 1 First make sure there is at least a WAN queue and it is enabled Croce CA a fe Default Queue as atm0 NN Patho SES ETH as eth SP 1 2 In QoS Classification Setup page Click Add to add a QoS Classification a a a eS e C fl pap
31. le ensuring that only the ports that require a given multicast stream actually receive it The DHCP server assigns an IP addresses from a pre set pool of addresses upon request from DHCP client e g your computer Do not disable the DHCP server unless you wish to let another device handle IP address issuance on the local network This is the beginning and ending range for the DHCP server addresses The amount of time before the IP address is refreshed by the DHCP Server If NAT is disabled and the PVC is the IPoA or static MER type this item allows you to inform the router of another DHCP server on your LAN To do this disable the DHCP server on the gateway Then input the IP address of the current DHCP server Click Apply and restart the gateway Use this feature to create a public network on your local LAN accessible from the Internet By assigning an address to this interface and then statically setting your LAN clients to the same network the LAN clients are accessible from the public network e g FTP or HTTP servers 26 WLAN VDSL Router User Manual 5 3 Wireless setting 5 3 1 Basic m i or m T rD uN Ww E Ed nm ou Ww cr AL O 3 g q O 3 OD T Wireless Guest Virtual Access Points Disable Enabled SSID Hidden te Wmm Enable Max eocrp Clients WMF Clients Advertise O wi0_Guest1 O O O O 16 IN A O wl0_Guest2 o O O O fis N A O pio_Guests jo O E O lis pwa
32. n IP address when it connects Enable PPP Debug Mode Select this to turn on the debug mode for the PPP connection Bridge PPPoE Frames Between WAN and Local Ports In addition to the VDSL Device s built in PPPoE client you can enable this to pass PPPoE through in order to allow LAN hosts to use PPPoE client software on their computers to connect to the ISP via the VDSL Device Each host can have a separate account and a public WAN IP address PPPoE pass through is an alternative to NAT for applications where NAT is not appropriate Disable PPPoE pass through if you do not need to allow hosts on the LAN to use PPPoE client software on their computers to connect to the ISP The PPP IP Extension is a special feature deployed by some service providers Unless your service provider specifically requires this setup do not select it If you need to select it the PPP IP Extension supports the following conditions It allows only one computer on the LAN The public IP address assigned by the remote using the PPP IPCP protocol is actually not used on the WAN PPP interface Instead it is forwarded to the computer s LAN interface through DHCP Only one system on the 17 WLAN VDSL Router User Manual LAN can be connected to the remote since the DHCP server within the ADSL gateway has only a single IP address to assign to a LAN device NAPT and firewall are disabled when this option 1s selected The gateway becomes the default gateway
33. nnect Ethernet cable Please make sure Ethernet cable is connected hub PC and ADSL router correctly Then please make sure the PC hub have been power on Please make sure that you use parallel network cable to connect UpLink port of hub or use parallel network cable to connect PC If connect normal port of hub not UpLink port you must use cross cable Please make sure that your network cables meet the networking requirements above PC cannot access the Router Please make sure that all devices communicating with the device must use the same channel and use the same SSID Otherwise your PC will not find the wireless Router PC cannot access the Internet First check whether PC can ping the interface Ethernet IP address of this product successfully default value is 192 168 1 1 by using ping application If ping application fails please check the connection of Ethernet cable and check whether the states of LEDs are in gear If the PC uses private IP address that is set manually non registered legal IP address please check 1 Whether IP address of the PC gateway is legal IP address Otherwise please use the right gateway or set the PC to Obtain an IP address automatically 2 Please confirm the validity of DNS server appointed to the PC with ADSL operator Otherwise please use the right DNS or set the PC to Obtain an IP address automatically 3 Please make sure you have set the NAT rules and convert private IP address to legal I
34. o a home or office 1 1 Features 1 1 1 Data Rate O Downstream data rate up to 100 Mbps O Upstream data rate up to SOMbps 1 1 2 VDSL Compliant e ITU G 992 1 G DMT e ITU G 993 2 G vds12 Profile 8a 8b 8c 8d 12a 12b and 17a e ITU G 992 2 G Lite e ITU G 994 1 G hs e ITU G 992 3 G DMT BIS e ITU G 992 4 G lite bis e ITU G 992 5 O Compatible with all T1 413 issue 2 full rate DMT over analog POTS and CO DSLAM equipment 1 1 3 Wireless O Fully IEEE 802 11n compatible O Wireless data rate up to 300Mbps O Operating in the unlicensed 2 4 GHz ISM band O Multi SSID O Supports 64 128 bits WEP security and user authentication 1 14 Network Protocol amp Features O Ethernet to ADSL Self Learning Transparent Bridging O Internet Control Message Protocol ICMP 1 WLAN VDSL Router User Manual IP Static Routing Routing Information Protocol RIP RIPv2 Network Address Translation NAT Virtual Server Port Forwarding Dynamic Host Configuration Protocol DHCP DNS Relay DDNS IGMP Proxy Simple Network Time Protocol SNTP VPN pass through IPSec PPTP L2TP Parent control 1 1 5 ATM Capabilities 1 1 6 FIREWALL RFC 1483 Multi protocol over ATM Bridged Ethernet compliant RFC 2364 PPP over ATM compliant RFC 2516 PPP over Ethernet compliant ATM Forum UNIB3 1 4 0 PVC Support up to 16 PVCs VPI Range 0 255 VCI Range 32 65535 UNI 3 0 amp 3 1 Signaling ATM AALS Adaption Layer
35. pages Connect to 197 168 1 1 Enter username admin and password adsiroot Remember my password Click OK After log on you will see the following screen Please select Wizard or Advanced mode The Wizard setup walks you through the most common configuration settings We suggest you use this mode if it is the first time you are setting up your router or if you need to make basic configuration changes Use Advanced mode if you need access to more advanced features not included in Wizard mode Go to Wizard setup Go to Advanced setup Click here to always start with the Advanced setup WLAN VDSL Router User Manual We can select wizard setup or advanced setup mode to setup KW5212 the wizard set up will guide us for a basic setting and the advanced setup will guide us to home page for more detailed setup 5 2 Internet Access Configuration 5 2 1 ADSL Setup From home page you can find Advanced Setup option on the left router configuration page 1 From Layer2 Interface click ATM Interface you can set it up according to the following steps You Choose Add or Remove to configure DSL ATM interfaces Interface Vni Va L IFES Peak Cell Rate Sustainable Cell Max Burst Size Link Conn IP MPAAL P Latency egory cells s Rate cells s bytes Type Mode QoS Prec Alg Wght 2 Click Add to configure PVC identifier select DSL latency and select connection mode according to your local o
36. pe v4 7 or later Factory Defaults The device 1s configured with the following factory defaults O IP Address 192 168 1 1 O Subnet Mask 255 255 255 0 O Encapsulation RFC 2516 LLC o VPI VCI According to local information Warnings and Cautions Never install telephone wiring during storm Avoid using a telephone during an electrical storm There might be a risk of electric shock from lightening Do not install telephone jacks in wet locations and never use the product near water To prevent dangerous overloading of the power circuit be careful about the designed maximum power load ratings Not to follow the rating guideline could result in a dangerous situation Please note that telephone line on modem must adopt the primary line that directly outputs from junction box Do not connect Router to extension phone In addition 1f your house developer divides a telephone line to multi sockets inside the wall of house please only use the telephone that has connected with the splitter of ADSL Router when you access the Internet WLAN VDSL Router User Manual 2 Hardware Description Front Panel On Power on 1 Green i Off No power On LAN link established and active via LAN port Green Blinking DSL data activity occurs Off No LAN link via LAN port On The wireless module is ready and idle WLAN Green Blinking Data transmitting or receiving over WLAN Off The wireless function is off On DSL link established
37. r Type IF 0800 e Source MAC Address 00 0e 14 23 45 12 Source MAC Mask fff fF 00 00 00 Destination MAC Address 00 23 22 23 23 22 Destination MAC Mask ii i Source IP Address Mask ha 192 168 1 12 Destination IP Address Mask 12 63 23 22 Differentiated Service Code Point DSCP Check 4F11 001010 Protocol UDP TCP Source Port port or port port UDP TCP Destination Port port or port port 80 3 Specify the classification results Here you must Assign Classification Queue Whether the following parameters are needed is according to your needs If you do not want to change the original information please leave it empty The queues listed here in the Assign Classification Queue are WAN interface queues set in Queue Config section Select the needed queue If you find none queues here turn back to check whether you have configured a queue and enable it Specify Classification Results Must select a classification queue A blank mark or tag value means no change Assign Classification Queue popUhatmlbPathObkevishPred v Mark Differentiated Service Code Point DSCP 3 Click Apply to save your settings The added rule will listed as below QoS Classification Setup A maximum 32 entries can be configured Choose Add or Remove to configure network traffic classes If you disable WMM function in Wireless Page classification related to wireless will not take effects CLASSIFICATION CRITERIA CLASSIFICATION RESULTS Cl
38. rovider to the LAN computer That is the PC becomes a host belonging to the same IP subnet The ADSL gateway bridges the IP packets between WAN and LAN ports unless the packet is addressed to the gateway s LAN IP address 7 Select a preferred wan interface as the system default gateway 13 WLAN VDSL Router User Manual Selected Default Available Routed WAN Gateway Interfaces Interfaces popu 1 8 Get DNS server information from the selected WAN interface or enter static DNS server IP addresses If only a single PVC with IPoA or static MER protocol is configured you must enter static DNS server IP addresses Select DNS Server Interface from available WAN interfaces Selected DNS Server Interfaces popu 1 Use the following Static DNS IP address Available WAN Interfaces 9 Make sure that the settings below match the settings provided by your ISP Click on the Apply Save button to save your configurations Connection Type PPPOE NAT Ful Cone NAT Disabled Firewall Ena bled IGMP Multicast Disabled Enabled Quality Of Service Enabled 14 WLAN VDSL Router User Manual 5 2 2 VDSL Setup From home page you can find Advanced Setup option on the left router configuration page 1 From Layer2 Interface click PTM Interface you can set it up according to the following steps You Choose Add or Remove to configure DSL PTM interfaces Interface DSL Latency PTM Priori
39. ser name and password that your ISP has provided to you Click Next 21 WLAN VDSL Router User Manual PPP Username O PPP Password fF O PPPoE Service Name fs Authentication Method AUTO e E Enable Fullcone NAT Dial on demand with idle timeout timer PPP IP extension Use Static IPv4 Address Enable PPP Debug Mode Bridge PPPoE Frames Between WAN and Local Ports Multicast Proxy Enable IGMP Multicast Proxy No Multicast VLAN Filter PPPoE service name can be blank unless your Internet Service Provider gives you a value to enter Authentication method is default to Auto It is recommended that you leave the Authentication method in Auto however you may select PAP or CHAP if necessary The default value for MTU Maximum Transmission Unit is 1500 for PPPoA and 1492 for PPPoE Do not change these values unless your ISP asks you to 22 WLAN VDSL Router User Manual Enable Full Cone NAT In full cone NAT all requests from the same private IP address and port are mapped to the same public source IP address and port Someone on the Internet only needs to know the mapping scheme in order to send packets to a device behind the VDSL Device The gateway can be configured to disconnect if there is no activity for a specific period of time by selecting the Dial on demand check box and entering the Inactivity timeout The entered value must be between 1 minute and 4320 minutes Use Static
40. the DNS server please consult with your ISP Click OK twice to confirm and save your changes Y ou will be prompted to restart Windows Click Yes Local PC Configuration in Windows 2000 l In the Windows task bar click the Start button point to Settings and then click Control Panel Double click the Network and Dial up Connections icon In the Network and Dial up Connections window right click the Local Area Connection icon and then select Properties Highlight Internet Protocol TCP AP and then click Properties In the Internet Protocol TCP IP Properties dialog box set the IP address as 192 168 1 x x can be a decimal number from 2 to 254 and the subnet mask as 255 255 255 0 and the default gateway as 192 168 1 1 Then click OR Configure the DNS tab if necessary For information on the IP address of the DNS server please consult with your ISP Click OK twice to confirm and save your changes WLAN VDSL Router User Manual 5 Web based Management Guide In order to use the web based management software it will be necessary to use a computer that occupies the same subnet as the Router The simplest way to do this for many users will be to use DHCP server that is enabled by default on the Router 5 1 LAN setting page Launch a web browser such as Internet Explorer and then use http 192 168 1 1 to log on to the setting
41. ty Conn Mode IP Qos Remove 2 Click Add to configure PTM Priority select DSL latency and select connection mode according to your local occasion After the configuration you need to click Apply Save Select DSL Latency PathO Fast C Fathi Interleaved Select Scheduler for Queues of Equal Precedence as the Default Queue Weighted Round Robin Weighted Fair Queuing Default Queue Weight 1 63 Default Queue Precedence 1 8 lower value higher priority Default Queue Shaping Rate Kbits s blank indicates no shaping Default Queue Shaping Burst Size bytes shall be gt 1600 3 Click WAN Service from the left menu Igmp HAT Firewall Remove Edit 4 Click Add to select a layer 2 interface for this service and then click Next ptm 0 11 v 5 Choose WAN service type just choose PPPoE for example here You can enter your own service description here if you want and then click Next 15 WLAN VDSL Router User Manual Select WAN service type PPP over Ethernet PPPoE IP over Ethernet Bridging Enter Service Description pppoe_0_1 1 6 Input PPP Username amp PPP Password and then click Next The user interface allows a maximum of 256 characters in the user name and a maximum of 32 characters in the password PPP Username PPP Password PPPoE Service Name fe Authentication Method AUTO yw FP Enable Fullcone NAT E Dial on demand with i
42. you to control the data upload traffic of each application from LAN Ethernet to WAN internet It facilitates you the features to control the quality and speed of throughput for each application when the system 1s running with full upstream load 33 WLAN VDSL Router User Manual Qos Queue Management Configuration If Enable QoS checkbox is selected choose a default DSCP mark to automatically mark incoming traffic without reference to a Device Info E Note If Enable Qos checkbox is not selected all QoS will be disabled for all interfaces Advanced Setup Layer2 Interface Note The default DSCP mark is used to mark all egress packets that do not match any classification rules WAN Service LAN Enable QoS NAT Security Parental Control Select Default DSCP Mark No Change 1 Y Quality of Service 005 Queue QoS Classification Quality of Service Check to activate this function and the following field will be available Select Default DSCP Mark Select the default DSCP mark from the list box Differentiated Services Code Point DSCP is the first 6 bits in the ToS byte DSCP Mark allows users to classify the traffic of the application to be executed according to the DSCP value The default DSCP mark is used to mark all egress packets that do not match any classification rules DSCP indicates three kinds of service Class Selector CS Assured Forwarding AF and Expedited Forwarding EF AF1 AF2 AF3 and AF4 are four kin
43. yption scheme that is used to protect user s wireless data communications WEP uses a combination of 64 bit keys or 128 bit keys to provide access control to user s network and encryption security for every data transmission To decode a data transmission each wireless client on the network must use an identical 64 bit or 128 bit key WEP is an older wireless encryption method that is not as hard to break as the more recent WPA 802 1x In 802 1x also known as RADIUS a separate machine called an authentication server receives a user ID and password It grants or denies access based on whether the ID and password match any entries in its account list User can optionally enable WEP encryption with this option Because it requires a separate machine acting as the authentication server 802 1x is most often used in business environments 30 WLAN VDSL Router User Manual WPA WPA is a more recent encryption method that addresses many of the weaknesses in WEP Any client capable of WPA encryption should use it instead of WEP WPA PSK This is WPA encryption combined with a pre shared key PSK which is a text string known only to the gateway and authorized wireless clients The gateway rejects the login if the client s PSK does not match WPA2 WPA2 is a more advanced encryption method than WPA Because it is a more recent standard some of user s wireless devices might not be able to use it WPA2 PSK
Download Pdf Manuals
Related Search