Automation PC 810.book
Contents
1. Automation PC Figure 5 Dimensions APC810 1 card slot variant Automation PC 810 User s Manual V 1 10 Information Measurement A depends on which heat sink is Model number used Value in mm 5AC801 HS00 00 12 8 5AC801 HS00 01 28 Nominal measurement area up to 6 mm General tolerance acc to DIN ISO 2768 medium over 6 to 30 mm over 30 to 120 mm over 120 to 400 over 400 to 1000 39 Chapter 2 Technical data2. 00 1000 MBit s See also page 73 or page 75 Optional with add on interface 5AC600 CANI 00 See also page 86 or page 87 Type 2 See also page 72 or page 73 2 RS232 modem capable not electrically isolated 16550 compatible 16 byte FIFO Max 115 kBaud 9 pin DSUB Also see page 76 USB 2 0 5 Low speed 1 5 MBit s full speed 12 MBit s to high speed 480 Mbit s Type A Max 500 mA or 1 A per connection Reset button Yes accessible behind the orange front doors Card slots Amount half size Add on UPS slot Automation PC 810 User s Manual V 1 10 4 directed outwards via fiber optic lines see also section status LEDs on page 81 See also section Card slot PCI PCle on page 80 1 Dimensions of the PCI PCle cards vary Table 15 Technical data APC810 1 card slot variant 37 Chapter 2 Technical data Technical data Entire device Power supply Rated voltage 24 VDC 25 Rated current 6A Starting current Typ 7 A max 50 A lt 300us Power consumption Component dependent see section Powercalculation with 5PC810 SX01 00 Revision gt DO on page 57 Mechanical characteristics Housing Material Galvanized plate plastic Paint Light gray similar to Pantone 427CV dark gray similar to Pantone 432CV Front cover Colored orange plastic similar to Pantone 144CV Outer dimensions See section Dimensions APC810 1 card slot variant on page 39 Weight approx 2 2 kg component depe
3. Technical data Entire device 2 Entire device 2 1 Overview of APC810 1 PCI slot variations 2 1 1 Interfaces Add on interface slot MIC Line IN Line OUT Add on UPS slot ia i 2 ea ee i PCI slot half size r a COM2 PCI or PCle F Supply voltage 24 VDC Monitor Panel SDL Smart Display Link DVI ETH1 10 100 1000 MBit ETH2 10 100 1000 MBit USB2 USB4 max 500 mA USB1 USB3 max 1A gt Warning sign Heat sink seal VOID WARRANTY IF SEAL BROKEN Heat sink 1 Depending on the bus unit being used Figure 3 Interface overview APC810 1 card slot variant top Warning Do not remove the mounting screws from the heat sink as it is connected to the processor and chipset by a thermal coupling If this connection is broken the APC810 must be sent for repair Removal of the mounting screws which can be determined by a broken seal voids all warranty During operation surface temperatures of the heat sink may reach 70 C warning hot surface Automation PC 810 User s Manual V 1 10 35 Chapter 2 Technical data Technical data Entire device Status LEDs Input 24 VDC 1 6A Fuse 125 VDC 10A move or insert ompact Flash or open housing while power is on CMOS Profile switch Power Reset button Hardware Security Ke Permanent Slide in compact slot A 7 Connection via SATA CompactFlash slot CF2 Connection via IDE PATA co Rev Com
4. ndent Ambient temperature Operation Component dependent see section 2 4 Ambient temperatures on page 50 Storage 20 C 60 C Transport 20 C 60 C Relative humidity Operation Storage Transport Component dependent see section Humidity specifications on page 55 Component dependent see section Humidity specifications on page 55 Component dependent see section Humidity specifications on page 55 Vibration Operation continuous 2 9 Hz 1 75 mm amplitude 9 200 Hz 0 5 g Operation occasional 2 9 Hz 3 5 mm amplitude 9 200 Hz 1g Storage 2 8 Hz 7 5 mm amplitude 8 200 Hz 2 g 200 500 Hz 4 g Transport 2 8 Hz 7 5 mm amplitude 8 200 Hz 2 g 200 500 Hz 4 g Shock Operation 15g 11 ms Storage 30 g 15 ms Transport 30 g 15 ms Protection type IP20 Altitude Operation max 3000 m component dependent Table 15 Technical data APC810 1 card slot variant Forts 1 Maintenance Controller Extended 2 at 50 C 8 5 pA of the supplied components and a self discharge of 40 3 Depending on the process or batch there may be visible deviations in the color and surface structure 4 Maximum values as long as no other individual component specifies any other 5 Derating the maximum ambient temperature typically 1 C per 1000 meters from 500 meters above sea level 38 Automation PC 810 User s Manual V 1 10 2 1 3 Dimensions Technical data Entire device
5. pactFlash slot CF1 Connection via IDE PATA Serial number sticker Fan kit cover Figure 4 Interface overview APC810 1 card slot variant bottom Information The front doors contain two permanent magnets Contact between a data carrier that saves data magnetically hard disk diskette the magnetic strip of a credit card etc and a magnet can cause loss of data 36 Automation PC 810 User s Manual V 1 10 Technical data Entire device 2 1 2 Technical data APC810 1 card slot variant BIOS Processor Component dependent see technical data for the CPU boards 945GME on page 95 Boot loader Operating system Cooling Method Main memory Graphics Controller Power failure logic Controller Buffer time Real time clock RTC Battery buffered Accuracy SRAM Battery buffered Quantity Battery Type removable Lifespan Ethernet Amount Speed Controller CAN bus CompactFlash Type Amount Serial interface Amount Type UART Transfer rate Connection USB interface Type Amount Transfer rate Connection Current load Passive via heat sink and optionally supported with an active fan kit Max 3GB Component dependent see technical data for the CPU boards 945GME on page 95 MTCX see also page 384 10 ms Yes see technical data of the CPU boards 945GME on page 95 See also page 84 Renata 950 mAh Yes accessible behind the orange front doors 2 1 2 years 2 10 1
Download Pdf Manuals
Related Search