Product Manual - Backyard Ocean
Contents
1. filter bag properly installed This will damage the impeller and void the warranty the Front Wheel NOTE You should not need to apply excessive force in Vac Head with Wheels only Vac Head with Brushes and Front Wheel only NOTE Inserting the wheels into the vacuum head may require a good deal of force If you have trouble you may find it easier to insert them by placing the wheel on a hard surface and pushing down on the head CAUTION Wheels OR Brushes with Front Wheel must be installed prior to use Water Tech is NOT responsible for damages to your pool if neither the wheels nor brushes with Front Wheel are installed in the vacuum head before use order to close the latch If you have trouble make sure the filter bag is not between the seal and the nose cap or fun nel and there are no other obstructions such as sand HOW TO USE YOUR POOL BLASTER A CAUTION The Pool Blaster is designed for under water use only OPERATING TEMPERATURES Unit must be submerged in water to operate properly Maximum operating temperature is between 5 C 41 F and 40 C 104 F Maximum operating depth is 15 ft Your Pool Blaster is designed for use in 3 different ways to vacuum your pool or spa P D A A lt VW A Vacuum using the Kane and the vacuum head removed B Vacuum using the handle and attached vacuum head with either wheel or brush attachments depending on pool type C Vacuum using a2. from the pool when done cleaning WHEN USING HANDLE Lift from pool with the nose facing up to allow the water to escape from the back and sides WHEN USING A VACUUM POLE Remove the unit from the pool with the bottom facing upwards and the handle facing down This will allow the water to escape and keep the dirt inside Q How can I prevent sand and silt from escaping through the filter bag A The Pool Blaster comes standard with an all purpose filter bag A Sand and Silt bag Part No PBWO22SS or a Microfilter bags are available To purchase contact your retailer or see our website at www PoolBlaster com Q What if put fhe Pool Blaster in the pool without the On Off Knob in place A Do not operate your Pool Blaster if water gets inside the machine Put the Pool Blaster on its side to drain the water out of the knob hole and tilt side to side to get the water out COMMON QUESTIONS Do not use for at least 24 hours If possible you can soeed the drying process with a blow dryer To avoid serious injury or damage do not replace the knob or attempt to charge or Operate your Pool Blaster until it is completely dry Q Can I leave my Pool Blaster on the charger all the time A After charging is complete the Pool Blaster and charger should be removed from the outlet This will prevent over charging and prolong the life of your battery pack IMPOR TANT Disconnect the charger before storing your Pool Blaster Q Can I rep
3. has entered the motor box area use a blow dryer on warm setting to dry any moisture build up on the inside of the motor box Water entering the Pool Blaster body presents no safety hazard and should be drained occasionally to avoid any chance of long term corrosion The batteries and motor in the Pool Blaster are long lasting and proper care will help to prolong the life of your appliance These guidelines and safeguards help insure that your new Pool Blaster operates effectively Please read all instructions carefully be fore using your Pool Blaster Please take a few moments to review the following IMPORTANT INFORMATION before using this tool SERVICE amp IMPORTANT SAFEGUARDS Service Information A WARNING Any repairs requiring disassembly should be performed by a Water Tech Authorized Service Cen ter For repairs please go to www waiertechcorp com for more information or call 1 800 298 8800 A WARNING To reduce the risk of fire electrical shock injury or damage to your machine A Do not use if unit is damaged in any way A Use this product only for its intended use as described in this manual Use only Water Tech accessories and filters A Never leave your Pool Blaster plugged in for long term storage A NEVER LEAVE YOUR Pool Blaster IN WATER WHEN IT IS OFF OR HAS RUN OUT OF BATTERY POWER A Do not use your Pool Blaster for pool openings the Pool Blaster is designed for general mainte nance of your pool or sp
4. position e Charge your Pool Blaster for at least 12 hours If none of the above help resolve the situation please call our Customer Service Division at 1 800 298 8800 or see us on the web at www PoolBlaster com 11 IMPORTANT DO NOT RETURN THIS PRODUCT TO THE STORE should you have any problems or questions concerning your product you should contact Water Tech s Customer Service Division toll free in the U S at 1 800 298 8800 or via fax at 1 800 488 0700 or via the web AT Www PoolBlaster com Water Tech Corp 44 West Ferris St East Brunswick NJ 08816 USA Toll Free 1 800 298 8800 US only Email support WaterlechCorp com www WaterlechCorp com
5. a A The Pool Blaster is designed for underwater use only Do not attempt to use your Pool Blaster to clean anything other than your pool or spa It is not intended for use as an all purpose vacuum cleaner i r 1 A Close supervision is necessary wnen used near children Do not allow this vacuum cleaner to be used as a toy A This vacuum creates suction Keep hair loose clothing fingers and all parts of body away from openings and moving parts A Unit must be submerged in water to operate properly f 4 When not in use store the Pool Blaster indoors in a clean dry place Do not leave underwater in direct sunlight or exposed to extreme tempera tures You can operate the Pool Blaster without its vacuum head attachment but when using the vacuum head attachment make sure that ei ther the supplied wheels or brushes are inserted in place A Do not use without filter bag seal ring and nose cap in place A Replace damaged filter bag seal ring promptly A Avoid picking up hard sharp objects with the vacuum They may damage the vacuum and the filter bag A Do not use to pick up toxic substances flam mable or combustible liquids such as gasoline or operate in the presence of explosive or flam mable fumes A Never insert or drop any object into any opening onthe device Keep all openings free of leaves rocks or anything that may reduce water flow Do not use on or near hot surfaces A Use ext
6. cation is misuse and could result in a hazardous condi tion leading to possible serious injury The batteries and motor are factory sealed in the motor box and CANNOT BE REPLACED Do not attempt in any way to destroy or disassemble motor box or any of its components Instead take your Pool Blaster to an authorized service center Failure to follow these instructions may void your warranty agreement General maintenance of your Pool Blaster requires you occasionally clean off the O rings on the ON OFF knob and add silicone lubricant sealant This will ensure easier turning and a water tight seal This lubricant is available at your local pool amp soa or hardware retailer In the Nose Cap Part No PBA002 there is a Flapper Valve To keep the Nose Cap Flapper Valve moving freely clean the valve after every use This will help to keep dirt inside the Pool Blaster after the cleaner is removed from the pool MAINTENANCE Service Information NOTE Any repairs requiring disassembly must be performed by a Water Tech Authorized Service Center For the repair center nearest you call us toll free at 1 800 298 8800 Unauthorized repairs will void the warranty Storing the Pool Blaster NOTE State of the art Nickel Metal Hydride batteries power the Pool Blaster These are the same batteries used in many portable phones In order to properly ventilate and cool the batteries and drive system a certain amount of space is left open i
7. d or mounted away from such hot surfaces Charging The Battery Pack For The First Time Only charge the Pool Blaster with the charger provided with the unit The charger provided is specially designed for the Pool Blaster Please note that the Battery Pack for your Pool Blaster has been shipped in a low voltage condition You must charge the Pool Blaster Battery Pack for 12 Hours Before Initial Use CHARGING YOUR CLEANER TO RECHARGE THE CLEANER 1 Turn the knob counterclockwise to remove the On Off Knob This will expose the charging jack connection NOTE When removing the On Off Knob it is normal to hear air escaping The air inside has simply expanded from being heated by the motor 2 Connect the lead plug from the charger to the charging jack on the Pool Blaster 3 Connect the charger to the appropriate electrical outlet The Pool Blaster should be re charged for 10 12 hours 4 After charging ensure that the On Off knob is fully secure and turned to the On position before attempt ing to use your Pool Blaster 5 The ON OFF knob should remain disconnected from the unit and left hanging form the attached lanyard until the Unit is ready to be used Do Not leave the unit plugged into the charger for more than 24 hours CAUTION Replace the ON OFF knob tightly before plac ing the Pool Blaster in water Placing the Pool Blaster in water without tightening the ON OFF knob so that the unit is ON will voi
8. d your warranty BATTERY LIFE e Your battery pack should give you many hours of use If fhe motor batteries or charger stop working please review the warranty information and or read the Commonly Asked Questions e The batteries are factory sealed in the motor box and CANNOT BE REPLACED Do not attempt in any way to destroy or disassemble the motor box or any of its components Under no circumstanc es should you attempt to open the battery pack and replace the batteries yourself PREPARING THE VACUUM HEAD SETTING UP YOUR POOL BLASTER FOR USE INSERTING THE FILTER BAG Inserting Wheels and Brushes in the Vacuum Head _ Inserting the Filter Bag and Nose Cap Your Pool Blaster has been configured with wheels and brushes at the factory in a manner which we have found perform best in most swimming pool applications Vac Head with Wheels and Brushes as provided l with you Pool Blaster Should you wish to experiment with different configurations you can refit the head with just wheels or just brushes with Place the Pool Blaster on its end on a stable and secure surface Place the filter bag seal ring part no PBWO22AP into the Pool Blaster as shown in diagram Make sure the rubber seal ring sits on the funnel All of the filter bag must be inside the funnel to ensure the head closes fully Close the latch squeezing the filter bag seal ring in between Never use the Pool Blaster without the
9. do A Clean off the O rings and add silicone lubricant sealant This will ensure easier turning and a better water tight seal Refer to the maintenance section for more information Q Can my Pool Blaster be run out of water A Yes for a short period of time when you turn it on before subomegring in your pool or soa or when removing it from the pool or spa Q When I am cleaning my pool how do I know when the Pool Blaster is out of battery power A Most people can feel the Pool Blaster is running through vibration in the vacuum pole or handle To be sure you can lift it out of the water to hear if it is running or not Q How offen should I clean out my Pool Blaster filter bag A You can clean your filter bag as often as you like with no ill effects The filter bag can then be turned inside out and rinsed with a hose or in a sink Do not wash it in a washing machine or with detergent For more detailed instructions see Cleaning Your Pool Blaster instructions in this manual For best results Go this after each use or whenever you notice the performance of your Pool Blaster declining Q Is it normal for me to hear air escaping out of fhe Pool Blaster when I open the On Off knob A Yes the powerful motor heats the air in the motor box which then expands creating the air sound Q How can stop dirt from coming out of fhe nozzle when take the cleaner out of the water A There are two ways to remove the unit
10. e filter bag seal ring high level debris occurances be aware that you will have should be checked emptied and cleaned after each to empty the Fiter Bag much more offen than normal It use or whenever you notice the performance of you Pool may take several cleaning and recharging cycles to clean Blaster declining your pool Microfilter Bag The Microfilter Bag should only be used to remove fine sand silt algae and other small particles from your pool Be aware that due to the high degree of filtration that this bag affords It fills much more rapidly than the All Puroose bag and therefore must be emptied frequently during pool cleaning to insure optimum performance A WARNING never use your Pool Blaster without the filter bag seal ring and nose cap properly in place Doing so will VOID the warranty Using a standard pool pole The pole attachment on your Pool Blaster is designed to accommodate any standard pole To attach a pole simply press down on the alignment pins on the pole retaining spring clip Aligning the holes slide the pole onto L the Pool Blaster and release the clip ALIGNMENT PINS AAWARNING Do not lean on pole or use pole to support weight To clean the filter bag Unplug the Pool Blaster from the charging outlet before changing the filter or performing any other routine maintenance Place the Pool Blaster on its end remove the vacuum pole if attac
11. er is not working as it should or has been dropped or damaged in any way return it fo a service center before using Call 1 800 298 8800 for a center nearest you A This product contains a sealed nickel metal hy dride battery Do not incinerate battery as it will explode at high temperatures Always dispose of the battery in accordance with your state law A Leaks from a battery cell can occur under extreme conditions If the battery liquid gets on the skin wash immediately with water If it gets in your eyes immediately flush your eyes with a mild solution of baking soda and water and seek medical attention ITEM No O Aa O N CO NI amp POOL BLASTER BODY CHARGER VACUUM HEAD WHEELS VACUUM HEAD BRUSHES VACUUM HEAD a FUNNEL HANDLE ON OFF KNOB NOSE CAP FILTER BAG SEAL RING VACUUM POLE CONNECTION SPRING CLIP DESCRIPTION PART No QTY ADDITIONAL PARTS AVAILABLE FOR PURCHASE Vacuum Head PBAOO6G sand amp Silt bag part No PBWO022SS 1 Vacuum Head Brushs PBWOA9 6 Microfilter Bag part No PBWO22MF to be used in Vacuum Head Wheels PBWO50 5 conjunction with the Sand amp Silf bag 1 1 Nose Cap PBAOO2 shallow Water Hose Attachment part No PBASHA All Purpose Filter Bag PBWO22AP U S Charger part No PBAO99L w Seal Ring European 230V Charger part No WI3843 Pool Blaster PBAOOS Battery Charger PBAO99 1 To purchase contact your retailer or call us at S
12. erence by one or more of the following measures Reorient or relocated the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different than that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help NOTE Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Before Initial Use CONGRATULATIONS on your purchase of a top quality Water Tech product which has been thoroughly tested to meet our exacting quality control standards The Pool Blaster vacuum is powered by Nickel Metal Hydride bat teries These batteries will operate at their peak after the second or third charge A precise amount of space is left open in the Pool Blaster body to properly ventilate and cool the batteries seals and drive system Please take care to tighten the On Off Knob when turning the unit on and before you submerge the unit in water to prevent any water from entering the motor box From time to time water may enter the motor box To drain any water that may enter the motor box allow all the water to drain from the exterior vacuum area than re move the On Off Knob and turn the machine so the knob is towards the floor and tilt side to side in all directions The amount of water may be very small or not noticed at all If water
13. hed Unlatch the nose cap Remove the filter bag seal ring by pulling it out of the funnel Invert the filter bag seal ring shsake out the large debris and rinse with a garden hose or in a sink Note Do not clean in a washing machine or with detergent Re insert the filter bag when finished Note Your reusable filter bag should be re placed if the seal ring is worn or if the bag is torn Important Tips Store your Pool Blaster in a clean dry place when not in use Do not leave it underwater in direct sunlight or exposed to extreme heat or cold You may clean the Pool Blaster body with soap and water Avoid using solvents when cleaning plastic parts Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use Use clean cloths or paper towels to remove dirt dust oil grease etc The On Off knob should be periodically lubricated with a silicon based grease The ON OFF knob should remain disconnected from the unit and left hanging from the attached lanyard until the unit is ready to be used CAUTION Do not at any time let brake fluids gasoline pe troleum based products penetrating oils etc come in contact with plastic parts They contain chemicals that can damage weaken or destroy plastic WARNING Do not attempt to modify this tool or create ac cessories not approved for use with this tool Any such alteration or modifi
14. i sidiidddddddddddaadadddadadaaddiddiadidiiddddd i i d ad POOL BLASTER MAX Handheld Pool amp Spa Cleaner Use and Care Manual IMPORTANT DO NOT RETURN THIS PRODUCT TO THE STORE should you have any problems or questions concerning your product you should contact Water Tech s Customer Service Division toll free in the U S at l 800 298 8800 or via fax at 800 488 0700 or via the web AT Www PoolBlaster com Warning This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation NOTE This equipment has been tested and found to comply with the limits for a Class B digital device pursu ant to Part 15 of the FCC Rules These limits are de signed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television recep tion which can be determined by turning the equipment off and on the user is encouraged to try and correct the interf
15. lace the batteries myself A Under no circumstances should you attempt to open the motor housing or battery housing Ihe batteries and motor are factory installed and sealed and your rechargeable battery should give you many hours of use If your motor batteries or charger stop working take the Pool Blaster to an authorized service center Q Where can I buy replacement parts A Look for original Water Tech replacement parts at your local retailer or on the web at www PoolBlaster com Q Will my pool chemicals hurt the Pool Blaster A The Pool Blaster is designed to withstand pool chemicals during its usage period However it should be rinsed off with fresh water after it is removed from the pool This will increase the life of the filter bag seal ring Q Can I leave the Pool Blaster in the pool when not in use A No The Pool Blaster should be removed from the pool and stored in a clean dry place when not in use This will increase the life of your Pool Blaster and its accessories Q What do I do if my Pool Blaster does not vacuum A Make sure your Pool Blaster is completely submerged in the water and the air is out of the clear funnel The cleaner is only designed to vacuum water and will not vacuum alr If that does not resolve your situation please check the fol lowing e Make sure the filter bag is clear of debris that may be obstructing the flow e Make sure the Pool Blaster knob is in the 12 o clock ON
16. n the Pool Blaster body As a result from time to time water may enter the unit In order to allow for any water to be drained you should remove the On Off Knob after each use turn the machine so the knob is towards the floor and tilt side to side in all directions The amount of water may be very small or not noticed at all After removing any water use a blow dryer on warm setting to dry any moisture build up on the inside of the motor box Water entering the Pool Blaster body presents no safety hazard and should be drained to avoid any chance of long term corrosion The batter ies and motor in the Pool Blaster are long lasting and proper care will help to prolong the life of your appliance NOTE Remove Pool Blaster from charger before storage When not in use your Pool Blaster should be stored indoors in a clean dry location sheltered from direct sunlight extreme tem peratures and rain Do not store the Pool Blaster in a garage or anywhere the unit could freeze Storing the Pool Blaster in areas of high humidity can affect battery performance over time The ON OFF knob should remain disconnected from the unit and left hanging from the attached lanyard until the unit is ready to be used For your convenience the Pool Blaster has an oval opening in the pool pole adaptor on which you can hang the unit Long Term Storage Follow the above storage instructions and unplug the charger from the electrical outlet Your Pool Blaster sh
17. ould be charged once a month during long term storage to maintain the battery pack DO NOT leave the Pool Blaster charging for a period of more than 24 hours When charging for the first time after long term storage your Pool Blaster may take 2 3 uses before maximum performance is achieved The ON OFF knob should remain disconnected from the unit and left hanging from the attached lanyard until the unit is ready to be used LIMITED WARRANTY Water Tech Corp WT warrants this product including supplied accessories against defects in material or workmanship for the time periods as set forth below Pursuant to this Limited Warranty WT will at its option i repair the product to the original specifications or ii replace the product with a new or refurbished product In the event of a defect these are your exclusive remedies For purposes of this Limited Warranty refurbished means a product or part that has been returned to its original specifications All Pool Blaster Battery Powered Pool amp Spa Vacuums For a period of one 1 year from the original date of purchase of the product WT will at its option repair or replace with new or refurbished product or parts any product or parts determined to be defective Accessories Included accessories are covered by this Limited Warranty for a period of 90 Days Instructions Please retain the original box and internal packaging materials To obtain warranty service you must com
18. ply with the following requisite instructions 1 Visit Water Tech Corp s Customer Support Department at www wtrma com You will be guided through the correct process on how to obtain the required RMA Return Merchandise Authorization Number All customers must obtain an RMA number before any product will be accepted for warranty service If you need additional assistance please contact us by telephone 800 298 8800 or email customerservice watertechcorp com 2 Package the unit with all accessories properly and securely in the original box 3 Attach your RMA number and Bar Code you received from the website to the outside of the package If you could not print the RMA number and bar code from the website you must write your RMA number in thick black indelible marker on two sides of the box 4 Send the package by USPS or express courier of choice to Water Tech Corp 44 West Ferris Street East Brunswick New Jersey 08816 WT suggests you insure the contents of your package WT is not responsible for lost stolen or damaged property in transit to WT Repair Replacement Warranty This Limited Warranty shall apply to any repair replacement part or replacement product for the remainder of the original Limited Warranty period or for ninety 90 days whichever is longer Any parts or products replaced shall become the property of WT This Limited Warranty covers only product issues caused by defects in material or workmanship during ordinary cons
19. pring Clip PBWO41 1 800 298 8800 or see us on the web at www PoolBlaster com SETTING UP YOUR POOL BLASTER FOR USE Charging the Battery Pack PRECAUTIONS Make sure power supply is normal household voltage 120 volts 60 Hz 240 volts 50Hz International AC only Do not handle Pool Blaster while charging with wet hands or without shoes Do not use or store your Charger Outdoors Charge battery indoors in a clean ary place For best results your Pool Blaster battery should be charged in a location where the temperature is above 50 F and below 100 F Only use the charger supplied to recharge this vacuum Do not use the supplied charger with any other appliance or damage may Occur Disconnect Pool Blaster from power charger when not in use Unplug the charger from outlet before any rou fine Cleaning or maintenance The use of extension cords is not recommended Plug the charger into a properly grounded stan Card electrical outlet 120v 60Hz US 240 volts 50Hz International only lo protect against risk of electrical shock Qo not put unit Charger in water or other liquid Io avoid damage to fhe charger and cord never carry the charger by the cord or yank to disconnect from an outlet Instead firmly grasp the charger boqay and pull to disconnect Do not pull cord around sharp edges or corners Do not allow the cord to hang over the edge of q fable or counter or touch hot surfaces The vacuum should be place
20. ra care when cleaning on stairs A Make sure the Pool Blaster is unplugged from the charger and in the off position before clean ing filter change or any other routine mainte nance A While Pool Blaster is charging do not handle with wet hands or without shoes A Only use the charger supplied to recharge this vacuum Do not use the supplied charger with any other appliance A To protect against risk of electrical shock do not put Charger in water or other liquid fA To avoid damage to the charger and cord never carry the charger by the cord or yank to disconnect from an outlet Instead firmly grasp the charger body and pull to disconnect Do not pull cord around sharp edges or corners A Do not allow the cord to hang over the edge of a table or counter or touch hot surfaces A Do not operate with a damaged cord or char ger A Do not use or store charger outdoors Charge your Pool Blaster indoors in a clean dry place Do not expose charger to rain or extreme tem peratures A For best results operate the charger in a location where the temperature is more than 50 degrees F but less than 100 degrees F AA Disconnect charger from power supply when not in use and before any routine cleaning or maintenance A The use of extension cords is not recommended Plug the charger into a properly grounded stan dard electrical outlet 1 20v 60Hz US 240 volts SOHZ International only A If vacuum clean
21. standard pool accessory pole not supplied with the attached vacuum head Caution Vacuum Head must be used when using a pole Choosing the Proper Filter Bag Standard All Purpose Filter Bag The Pool Blaster with its Standard Filter Bag is intended for routine pool maintenance only Should there be an Once your Pool Blaster is set up for use you may put it in your pool or Spa Bring your Pool Blaster to the side of the Pool or Spa and turn it on by turning the On Off knob all the way to the On position This must be done outside of the water before it is submerged Once the Pool Blaster is On it can be com pletely submerged in water and is ready for use This appliance is designed to be in water only when in the ON position and has batery power Excessive leaking can occur when not running and void the warranty Never leave your Pool Blaster in the water when it is off NOTE There are two ways to remove the unit from the pool WHEN USING HANDLE Lift from pool with the nose facing up to allow the water to escape from the back and sides WHEN USING A POOL POLE Remove the unit from the pool with the bottom facing upwards and the handle fac ing down This will allow the water to escape and keep the dirt inside excessive amount of debris ie when opening the pool for Cleaning the reusable filter bags the season cleaning following major storm activity or other For maximum cleaning efficiency th
22. umer use it does not cover product issues caused by any other reasons including but not limited to product issues caused by commercial use acts of God misuse abuse limitations in technology or modification of or to any part of the WT product This Limited Warranty does not cover WT products sold AS IS or WITH ALL FAULTS or consumables such as batteries This Limited Warranty is invalid if the factory applied serial number has been altered or removed from the product This Limited Warranty is valid only in the United States and Canada EXPRESS LIMITATION THIS LIMITED WARRANTY ONLY APPLIES IF THE PRODUCT WAS PURCHASED FROM AN AUTHORIZED WATER TECH DEALER THIS WARRANTY IS NOT TRANSFERABLE LIMITATION ON DAMAGES WT WILL NOT BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF EXPRESSED OR IMPLIED WARRANTY ON THIS PRODUCT DURATION OF IMPLIED WARRANTIES EXCEPT TO THE EXTENT PROHIBITED BY LAW APPLICABLE LAW ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FORA PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION OF THIS WARRANTY some states do not allow the exclusion or limitation of incidental or consequential damages or allow limitations or how long an implied warranty lasts so the above limitations or exclusions may not apply to you This Limited Warranty gives you specific legal rights and you may have other rights which vary from state to state 10 Q The ON OFF knob has become difficult to turn What can
Download Pdf Manuals
Related Search