1 MB 6th Jan 2014 W70SBIR, W70MBIR & W70LBIR
Contents
1. Vandal Resistant IR Bullet Camera 10 11 12 13 14 15 Important Safety Instructions Read these instructions Keep these instructions for later use Pay attention to all warnings and adhere to them Follow all instructions Do not immerse this product in water Clean only with a lint free dry cloth Do not block any ventilation openings Do not install near any heat sources such as radiations heat registers or other products including amplifiers that produce heat Protect the power cord from being walked on or being pinched especially at power receptacles and the point where they exit from the camera Only use accessories specified by the manufacturer For added protection for this product during a lightning storm or when it is left unattended and unused for long periods of time unplug it from the power Refer all servicing to qualified service personnel Servicing is required when the product has been damaged in any way such as power supply cord or plug is damaged it does not operate normally or has been dropped Do not operate the camera beyond its temperature humidity or power source ratings Operating temperature 14F 122F 20 C 50 C Humidity gt 85 Do not point the camera towards the sun spotlights or reflective surfaces Laser beams will damage the image sensor Do not project laser beam directly into the lens of the camera Vandal Resistant IR Bullet Camera Contents Chapte2. White Speckles A CCD image pickup device uses accurate techniques to capture an image however imperceptible speckles may occasionally appear on the screen This is related to the principles of a CCD mage sensor pickup device and not a malfunction The white speckles could appear under the following conditions Using the camera in high temperatures When turning up the gain Blooming This is a phenomenon is which the light from very bright objects appears to overflow into neighbouring areas of an image Note If strong light enters a wide area of the image the screen may become dark If this occurs move the camera away from the light source or adjust the iris to reduce the amount of light entering the lens Vandal Resistant IR Bullet Camera Chapter 5 Troubleshooting If you encounter trouble in using the camera please refer to the instructions below For more information please consult your local authorised distributor or service centre Problem No Video Output Check the power supply and the cable camera and moni tor connections Malfunction Check whether the camera is connected to the DC12V power supply L ightimatio Adjust the display contrast of the monitor Change the 9 9 location if the camera is exposed to intense light Dark Image Adjust the Brightness The situations below are not malfunctions of the camera Problem Solution Vertical Streak ie appear when the camera is exposed to intense When the ca
3. Manual AIS Privacy Masking Sharpness lisina Chinese English Japanese German French Russian guag Portuguese Spanish Lens Angle of View 92 27 2 IR Light 2 Piece LED Array 2 5W Each Heater Optional 7W Dimensions LxWxH weg Design and Specifications are subject to change without notice Vandal Resistant IR Bullet Camera 15 Features Built in 2 8 12mm IR 2MP Lens Built in ICR Easy Lens Focal Length Adjustment 2 Piece IR LED Array Total Power 7W Visible Range up to 30m in Ideal Conditions 3 Axis Vertical Horizontal Rotational Vandal Resistant Weatherproof IP66 Package Check the contents of the package The following items are included 1x User Manual 1x IR Bullet Camera 3x Fixing Screws with Dielectric Covers 1x Dielectric Paper 1x L type Screwdriver Product Parts Fixing Base 1 Locking Ring Bracket Screw Sunshield Screw 4 Sunshield 5 IR LED Array Photovaristor 7 Bottom Cover Screw cmm 8 1 Fixing Base 5 Sunshield Fix the camera to the ceiling or wall Protects the Camera Body 2 Locking Ring 7 6 IR LED Array Locks the Camera Body to the Fixing Base Provides a light source at night time 3 Bracket Screw 7 Photovaristor Adjusts and fixes the monitoring direction Photocell to turn the IR LED s On or Off 4 Sunshield Screw 8 Bottom Cover Screw Fixes the Sunshield to the Camera Body Locks the Focus and OSD cover Vandal Resistant IR Bul
4. UN i 3r 1 2 Loosening the side screw allows you to rotate the camera body or bracket in a vertical direction 3 Byrotating the camera body or bracket downward 90 in a vertical direction as above left picture the camera body or bracket can be rotated 360 Note The camera body or bracket can be rotated 360 only when in the position indicated in the above left photo Vandal Resistant IR Bullet Camera Chapter 2 W70MBIR Overview X Specification cp Image Sensor Sync System Resolution 650TVL Colour 700 TVL B amp W Minimum Illumination 0 01Lux F1 2 Colour 0 001Lux F1 2 B amp W Electronic Shutter Auto Manual Exposure Conto AES DC Drive Auto Iris Video Drive Auto Iris P Auto Manual AIS os Privacy Masking Sharpness Chinese English Japanese German French Russian Menu Language Portuguese Spanish Weight Design and Specifications are subject to change without notice Vandal Resistant IR Bullet Camera Features Built in 2 8 12mm IR Corrective Lens Built in ICR Easy Adjustment of Lens Focal Length 2 Piece IR LED Array Visible Range up to 25m in Ideal Conditions e 3 Axis Vertical Horizontal Rotational Vandal Resistant Weatherproof IP66 Package Check the contents of the package The following items are included 1x User Manual 1x IR Bullet Camera 4x Fixing Screws with Dielectric C
5. eneath the installation location Installing the Camera The installation process is described below C G g A Trough Step 1 Place the dielectric paper on the wall ceiling this is to protect the camera from damage by conducted currents Then fix the camera base to the wall ceiling with the three screws provided Pay attention to the cable trough Point it in the direction of the power supply if cables exit there Step 2 Attach the camera body to the fixing base Step 3 Fasten the camera body tightly using the gearing on the locking ring The installation is complete Cautions for Installation 1 Allow the cable to pass through the hole in the middle before mounting the camera to the base 2 If passing through the side the cable must be put in the cable trough first before the camera is mounted Vandal Resistant IR Bullet Camera Adjusting the Monitoring Direction ei D XK NI ra 7 J Pd F SNL P Sa Wn 1 Before tightening the locking ring you can rotate the whole Camera Body to the required surveillance position 2 Loosen the bracket screw and you can rotate the Camera Body horizontally according to your surveil lance need Tighten the bracket screw after you finish the adjustment 3 Loosen the side screw and you can rotate the camera body vertically according to surveillance need Tighten the side screw after you finish the adjustment Changing Camera Fu
6. er Consumption Max 2W Max 6W with IR LED s ON Weigh Design and Specifications are subject to change without notice Features Built in 3 6mm 1 3 IR 1 3 Megapixel Lens Built in ICR 2 Piece IR LED Array Total Power 4W Visible Range of up to 15m in Ideal Conditions e 8 Axis Vertical Horizontal Rotational Vandal Resistant Water Resistant IP66 Package Check the contents of the package The following items are included e 1x User Manual 1x IR Dome Camera e 3x Fixed Screws with Dielectric Covers e 1xDielectric Paper 1x L Type Screw Driver Vandal Resistant IR Bullet Camera Product Parts Fixing Base Locking Ring Fixing Base Fixes the camera to the ceiling or wall N Locking Ring Locks the Camera Body to the Base 3 IRLED Array Provides light source at night time 4 Photovaristor Photocell to turn on or turn off the IR LED s 5 Bracket Screw Adjust and fix the horizontal angle of view 6 Side Screw Adjust and fix the vertical angle of view Operating Instructions Connection 1 Connect one end of the BNC Cable to the terminals of a monitor or recording device 2 Connect the other end of the BNC Cable to the camera VIDEO OUT terminal 3 Then plug the power adapter into the power receptacle The image will be displayed when the monitor is on Vandal Resistant IR Bullet Camera Installation Before Installation Read the cautions before installati
7. f Genie LZ CCTV W70SBIR W70MBIR amp W70LBIR Vandal Resistant IR Bullet Camera User Manual Safety Precautions DO NOT ATTEMPT TO DISASSEMBLE THE CAMERA A Risk of Electric Shock Do Not Open A CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSON This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons This symbol is intended to alert the user to the presence of important operation and maintenance instructions in the literature accompanying the appliance Vandal Resistant IR Bullet Camera 10 11 Warning This product is patented for configuration appearance and design copying is not permitted If this product fails to operate normally contact your authorised distributor or service centre Never disassemble or modify the product in any way Problems caused by disassembly modification or repair invalidates the product warranty Electromagnetic fields at specific frequencies may cause image interference Only use a standard regulated power adapter Using any other adapter could result in fire electric shock or damage to the product Incorrectly connecting the power supply may result in fire electric shock or damage to the product Do not connect multiple cameras to a sin
8. gle adapter Exceeding the capacity may cause abnormal heat generation or fire Securely plug the power cord into the power receptacle A loose connection may result in fire When installing the camera on a wall or ceiling fasten it safely and securely A falling camera may cause personal injury Do not place conductive objects e g screwdrivers coins etc on top of the camera Do not install the unit in humid dusty locations If any unusual smell or smoke comes from the unit please stop using the product In such cases please immediately disconnect the power source and contact your local authorised distributor or Service centre Cautions Do not drop objects on the products or apply strong shocks to it Keep it away from locations subject to excessive vibration or magnetic field interference Do not install in a location subject to high temperatures over 122 F or 50 C low temperatures below 14 F or 20 C it may cause a fire If want to relocate the installed product turn off the power before moving or reinstalling it Remove the power plug from the outlet if there is a lightning storm Neglecting to do so may cause fire or damage to the product Avoid a location which is exposed to direct sunlight or near heat sources Neglecting to do so may cause fire Install in a well ventilated location Avoid aiming the camera directly towards extremely bright objects such as the sun as this may damage the image sensor
9. he terminals of a monitor or recording device 2 Connect the other end of the BNC Cable to the camera VIDEO OUT terminal 3 Then plug the power adapter into the power receptacle The image will be displayed when the monitor is on Vandal Resistant IR Bullet Camera Installation Before Installation Read the cautions before installation 1 Makesurethe installation location can support 5 times the total weight of the bullet camera 2 Make sure the cable doesn t get jammed inappropriately or allow the cable insulation to get damaged during installation This may result in a malfunction or a fire hazard 3 Make sure that nobody is beneath the installation location Installing the Camera The installation process is described below Step 1 Place the dielectric paper on the wall ceiling this is to protect the camera from damage by conducted currents Then fix the camera base to the wall ceiling with the four screws provided Pay attention to the cable trough Point it in the direction of the power supply if cables exit there Step 2 Attach the camera body to the fixing base Step 3 Fasten the camera body to the fixing base The installation is now complete Cautions for Installation 1 Allow the cable to pass through the hole in the middle before mounting the camera to the base 2 If passing through the side the cable must be put in the cable trough first before the camera is mounted Vandal Resistant IR B
10. let Camera Bottom Cover D 0 Video Out Port IR Illumination Adjustment OSD Setup Lens Zoom Lever Lens Focus Lever 9 Side Screw EN 12 IR Illumination Adjustment Adjusts and fixes the monitoring direction Adjusts the IR LED intensity 10 Bottom Cover 13 OSD Setup Seals and protects the Focus and OSD Sets the available OSD functions controls 14 Lens Zoom Lever 11 Video Out Port Adjusts the zoom ratio of the Lens Test Monitor connector for checking the image locally 15 Lens Focus Lever Adjusts the focal length of the lens Operating Instructions Connection 1 Connect one end of the BNC Cable to the terminals of a monitor or recording device 2 Connect the other end of the BNC Cable to the camera VIDEO OUT terminal 3 Then plug the power adapter into the power receptacle The image will be displayed when the monitor is on Vandal Resistant IR Bullet Camera 17 Installation Before Installation Read the cautions before installation 1 Make sure the installation location can support 5 times the total weight of the bullet camera 2 Make sure the cable doesn t get jammed inappropriately or allow the cable insulation to get damaged during installation This may result in a malfunction or a fire hazard 3 Make sure that nobody is b
11. mera is in a high temperature environment Fixed Image Clutter there may be fixed image clutter on the entire monitor Screen When shooting at a ribbon like object a straight line or Jagged Image something with a similar pattern the image displayed on the monitor may be serrated Chapter 6 Routine Maintenance 1 Regularly clean the dust and dirt from the lens surface of the camera with a dry lint free cloth to maintain clarity of image 2 Clean the camera body with dry soft cloth For stubborn dirt wipe it with a cloth dipped in a little neutral detergent and then dry the camera 3 Do not use volatile chemicals such as thinners alcohol benzene etc to clean the camera because they can damage the surface coating and even weaken the functionality and performance of the camera Vandal Resistant IR Bullet Camera 21 22 Memo Vandal Resistant IR Bullet Camera Memo Vandal Resistant IR Bullet Camera 23 ff Genie uZ CCTV GENIE CCTV LTD CCTV House City Park Watchmead Welwyn Garden City Hertfordshire AL7 ILT Tel 44 0 1707 330541 Fax 44 0 1707 330543 www geniecctv com Edition GN January 2014
12. nctions Loosen the bottom cover screw to open the bottom cover 1 Use the video out port for connecting a test monitor to the camera to locally check the image output 2 Set the required functions using the OSD setup 3 Rotate the IR Illumination adjustment to adjust the IR intensity appropriate to the application 4 Adjust the focal length with the lens zoom and focus levers to obtain the correct field of view Once a clear and focused image is achieved fully tighten the thumb screws 5 After all adjustments are completed lock and tighten the bottom cover using the bottom cover screw Vandal Resistant IR Bullet Camera 19 20 Chapter 4 Typical CCD Phenomena The following effects on the monitor screen are characteristics of CCD cameras They do not indicate any fault with the camera Smear This can occur when the camera is pointed toward a very bright object such as electrical lighting the sun or a strong reflection This phenomenon is caused by an electric charge induced by infrared radiation deep in the photosensor It appears as a vertical smear because the CCD imaging element uses an interline transfer system Vertical Aliasing When the camera is pointed toward vertical stripes or lines they may appear jagged Blemishes A CCD image sensor consists of an array of individual sensor picture elements Pixels A malfunctioning sensor element causes a single pixel blemish in the picture This is generally not a problem
13. on 1 Make sure the installation location can support 5 times the total weight of the bullet camera 2 Make sure the cable doesn t get jammed inappropriately or allow the cable insulation to get damaged during installation This may result in a malfunction or a fire hazard 3 Make sure that nobody is beneath the installation location Installing the Camera The installation process is described below Step 1 Place the dielectric paper on the wall ceiling this is to protect the camera from damage by conducted currents Then fix the camera base to the wall ceiling with the 3 screws provided Pay attention to the cable trough Point it in the direction of the power supply if cables exit there Step 2 Attach the camera body to the fixing base Step 3 Fasten the camera body tightly using the gearing on the locking ring The installation is complete Cable Trough DI IT lili Cautions for Installation 1 Allow the cable to pass through the hole in the middle before mounting the camera to the base 2 If passing through the side the cable must be put in the cable trough first before the camera is mounted Vandal Resistant IR Bullet Camera Adjusting the Monitoring Direction 1 Loosening the bracket screw allows you to rotate the camera body and bracket 180 in a horizontal direction AI LU ALII TT I
14. overs e 1xDielectric Paper 1x L type Screwdriver Product Parts Fixing Base Bracket Screw 1 Fixing Base Fixes the Camera to the ceiling or the wall 6 IR LED Array Provides a light source at night time 2 Bracket Screw Adjusts and sets the monitoring direction 7 Front Window Environmental protection for the Lens 3 Sunshield Screw Fixes the Sunshield to the Camera Body 8 Bottom Cover Seals and protects the Focus and OSD controls 4 Sunshield Protects the Camera Body 9 Bottom Cover Screw Locks the Focus and OSD cover 5 Photovaristor Photocell to switch the IR LED s On and Off Vandal Resistant IR Bullet Camera 11 Q A Lens Zoom Cover Lens Focus Lever e Gili esto D e OSD Setup I Video Out Port 10 Holder Screw Adjusts and sets the monitoring direction 11 Connector Screw Adjusts and sets the monitoring direction 12 Lens Zoom Lever Adjusts the zoom ratio of the Lens 13 Lens Focus Lever Adjusts the focal length of the Lens 14 OSD Setup Sets the available OSD functions 15 Video Out Port Test Monitor connector for checking the image locally Operating Instructions Connection 1 Connect one end of the BNC Cable to t
15. r 1 W7OSBIR Overview 1 rire 6 SQ Cee A 6 ECT te 6 leise eiii aviaria 7 Operaurnig Inst b DES aoo eresia ii 7 ISIS siii 8 Adjusting the Monitoring PISCIon asraniei alain 9 Chapter 2 W70MBIR OvervieW sssssssssuunnsnnnnnnnnnnnnnunnnnnnnnnnnnnnnnnnnnnnnn nnna 10 PE 2 82 8 sata alec RES A A eee ce 10 ESUIlIE Saia lieta aiar dai 11 FIR 11 Product Pans init naar er oe el vu etai 11 Operating Inl HollOfiS ssi rale 12 MSto Nepi iaia 13 Adjusting the Monitoring Direction iii enne enr uina 14 Chapter 3 W7OLBIR Overview eeeeeeeeeee eene eren nnns 15 He 8 2 8 ef 1108 9 m HE 15 FEE Met TTE 16 PAG cce a a E AE TH LA aa 16 Product Paliano ira opera xx adi E tb abd 16 Operating INStr CTION ks eee eee es uod a parti 17 VSAM alone dita a 18 Adjusting the Monitoring DIF GHOM criteria 19 Chapter 4 Typical CCD Phenomena eere 20 Chapter 5 Troubleshootig rc 21 Chapter 6 Routine Maintenance eeeeeeeeee eren 21 Vandal Resistant IR Bullet Camera Chapter 1 W70SBIR Overview Specification Q 2 Model Number W70SBIR Image Sensor CMOS Video Format PAL Effective Pixels 720 H x 576 V Minimum Illumination 0 1Lux F1 2 AGC ON 0 Lux with IR Sync System Video Output 1Vp p Composite Output 750 BNC Angle of View 70 IR Light 2 Piece LED Array 2W Each Pow
16. ullet Camera 13 Adjusting the Monitoring Direction Ve VT E j e CO eem LI TO The W70MBIR has a 3 axis gimbal design Loosen the holder bracket and connector screws then adjust the camera to the appropriate monitoring position After one direction is set tighten the relevant fixing screw Fully tighten all screws when all adjustments are completed Changing Camera Functions Loosen the bottom cover screw to open the bottom cover 1 Use the video out port for connecting a test monitor to the camera to locally check the image output 2 Setthe required functions using the OSD setup 3 Rotate the IR Illumination adjustment to adjust the IR intensity appropriate to the application 4 Adjust the focal length with the lens zoom and focus levers to obtain the correct field of view Once a clear and focused image is achieved fully tighten the thumb screws 5 After all adjustments are completed lock and tighten the bottom cover using the bottom cover screw Vandal Resistant IR Bullet Camera Chapter 3 W7OLBIR Overview Specification Model Number W70LBIR Image Sensor Sony 1 3 Super HAD Il CCD Video Format PAL Effective Pixel 976 H x 582 V Sync System Resolution 650TVL Colour 700 TVL B amp W Minimum Illumination 0 01Lux F1 2 Colour 0 001Lux F1 2 B amp W Electronic Shutter Auto Manual Exposure Control AES DC Drive Auto Iris Video Drive Auto Iris p Auto
Download Pdf Manuals
Related Search