Home
Oxford Infared Heater User Manual
Contents
1. 2 Red light must be on above Master Power Switch to operate Remote Control unlock the controls 2 Push the ESO feature U on the remote control to unlock the controls 1 Replace the battery in the Remote Control See Maintenance Section 2 Check to ensure the appliance is plugged in Call 1 877 744 3649 for assistance or email us at service phoenixinno com
2. Dedicated circuit is preferred but not essential in all cases a dedicated circuit will be required if after installation the circuit breaker trips or the fuse blows on a regular basis when the heater is operating Additional appliance on the same circuit may exceed the current rating of the circuit breakers WARNING 1 Ensure the power cord is not installed so that it is pinched or against a sharp edge and ensure that the power cord is stored or secured to avoid tripping or snagging to reduce the risk of fire electric shock or injury to persons 2 Construction and electrical outlet wiring must comply with local building codes and other applicable regulations to reduce the risk of fire electric shock and injury to persons Do not attempt to wire your own new outlets or circuits To reduce the risk of fire electric shock or injury to persons always use a licensed electrician SPECIFICATIONS Technical Specifications Model EA1231 Voltage 120V Frequency 60Hz Power 1500W OPERATING INSTRUCTIONS Read all instructions and warnings prior to operating the appliance Ensure that all controls are in the OFF position before plugging the appliance in to a properly grounded electrical outlet The control panel of the appliance is located in the centre See Fig 1 and Fig 2 Fig 1 Fig 2 When you first turn the heater on it may emit a slight but harmless odor This odor results from certain oils or gre
3. not use abrasive cleaners or spray liquids on any part of the appliance 5 Periodic cleaning vacuuming of the fan heater unit is strongly recom mended to ensure that no dirt or foreign objects build up Air Filter Cleaning 1 It is suggested to clean the air filter on the back on the electric fireplace on a regular basis 1 or 2 times per season or more depending on the amount of dust in the air Wash in soapy water 2 See Fig 5 and 6 for the steps to clean the air filter Battery Replacement 1 For the first time use the protective plastic tab for the battery must be removed See Fig 7 below 2 For remote control battery replacement use a Lithium Cell CR2025 3V battery See Fig 7 and 8 below for the replacement steps STORAGE Store the heater in a cool dry location when not in use To prevent dust and dirt build up use the original packaging to repack the unit Fig 5 Fig 6 Rear of unit 1 Remove bracket screws 4 pcs 2 Remove Filter Bracket 2 pcs 3 Remove Air Filter Fig gt Remove plastic tab for 1st use Battery Fig 8 Remote Control NOTE The heater will automatically set the Child Lock Feature and lock the controls after 8 seconds if there are no adjustments to the controls Push the Child Lock button R once to unlock the remote control and the control panel functions NOTE This appliance comes equipped with an overheat protection safety device Should the appliance begin to over
4. HEARTH TRENDS EA1231 HOME COMPEIORIGTWPRODUCTS Oxford Infared Heater User Manual SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE lf you are assembling this unit for someone else give this manual to him or her to read and save for future reference na L2039 INTERTEK 4001358 JUNE 2013 Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEARTH TRENDS _ ____ BUILDING Ag TRADITION HOME COMTFIORKRUHIPR ODUCTS IMPORTANT SAFETY INSTRUCTIONS Quick Reference Guide RISK OF ELECTRICAL SHOCK SGAUIUDLE las MB bi Valle NO USER Rennie INSIDE EQUIPMENT PLEASE READ THESE SA 1965 SA 1965 INSTRUCTIONS CAREFULLY saii READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE KEEP DRAPERY AND OTHER FURNISHINGS AT LEAST 3 3 FEET 1 METER FROM THE FRONT AND SIDES OF THE ELECTRICAL HEATER WARNING 1 WARNING TO REDUCE THE RISK OF FIRE KEEP COMBUSTIBLE MATERIAL SUCH AS FURNITURE PAPERS CLOTHES AND CURTAINS AT LEAST 3 FEET 0 9 M FROM THE FRONT OF THE HEATER AND AWAY FROM THE SIDES AND REAR 2 SERVICING SHOULD BE DONE ONLY WHILE THE ELECTRICAL HEATER IS DISCONNECTED FROM THE POWER SUPPLY 1 Before permanently placing your electric fireplace plug it into a SPECIAL CHARACTERISTICS convenient outlet to verify that the circuit breakers A This heater is ideal for use all year round even when central for the outlet are on heating has been turned off 2 The heater may emit a sli
5. ases being heated as the appliance is used for the first time This odor is perfectly safe and will stop shortly it will not reoccur after the first operation of the appliance Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEARTH TRENDS ______ BUILDING SL S TRADITION HOME COMFIORUHIPR ODUCTS OPERATING INSTRUCTIONS Using the Control Panel See Fig 3 Below Master Power Switch A e Push button A to turn electric fireplace on Ensure that the red power light B above the Master Power Switch is on this confirms that the unit is plugged in It will turn from red to green when the Master Power Switch is pushed e The flame effect will automatically come on when the electric fireplace is on Fan Button C e This is a High and Low setting for the fan and the heater Note that the fan will only come on if the thermostat temperature is set above the room temperature e The fan light D denotes the Low fan setting and the fan light E denotes the High setting Timer F e f a timer is desired push this button once for a 1 hour timer twice for a 2 hour time etc up to 12 hours The time will show on the digital readout screen To reset keep pushing the Timer button F until it returns to your desired time setting Note that the timer is approximate and extreme caution is necessary when the electric fireplace is left operating and unattended Keep children invalids and and pet
6. e to release the appliance from the Energy Savings Option NOTE Direct the remote control at the appliance from 1 to 5 meter distance for the remote control to function properly The remote control receptor is located in the control panel Fig 1 NOTE For remote control battery replacement use Lithium Cell CR2025 3V Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEARTH TRENDS ____ BUILDING SL S TRADITION HOME COMFIORUHIPR ODUCTS MAINTENANCE WARNING BEFORE CLEANING THE EXTERIOR OF THE APPLIANCE DISCONNECT THE UNIT FROM THE POWER SUPPLY AND LEAVE UNTIL COOL CAUTION DO NOT USE ABRASIVE CLEANERS ON THE GLASS PANEL DO NOT SPRAY LIQUIDS DIRECTLY ONTO ANY SURFACE OF THE UNIT WARNING AN AUTHORIZED SERVICE REPRESENTATIVE SHOULD PERFORM ANY OTHER SERVICING WARNING Before attempting to perform any maintenance on this appliance turn all controls to the OFF position and unplug Allow the appliance to be OFF for at least 15 minutes before performing any maintenance in order to allow all components to cool properly Cleaning 1 To remove dust from glass window use clean dry cloth 2 To remove fingerprints or other marks from glass window use clean damp cloth Do not spray glass cleaner or other liquids directly onto the window 3 Clean metal surfaces with a clean damp cloth making sure not to push dust or debris into any air intake or exhaust vents 4 Do
7. ght harmless odor when first used B This heater produces a hot current of air This odor is normal and is caused by the initial heating of internal heater parts and will not occur again UNPACKING AND INSTALLING THE ELECTRICAL HEATER 3 If your electrical heater does not emit heat consult your owner s 1 Open the packaging carefully and remove the heater manual for further information 2 Remove and discard the plastic bag 3 BE RESPONSIBLE HANDLING THE PACKING MATERIALS WARNING KEEP PLASTIC WRAPPING AWAY FROM CHILDREN 4 Keep the original packing for future transport and or storage 5 Keep the front of the unit through which the heat is radiated at least 3 3 feet 1 meter away from furniture curtains and other flammable objects materials at all times 6 Ensure there is a grounded socket nearby back of the appliance 7 The power cord must remain at the back of the appliance and must not be in contact with any hot element Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEARTH TRENDS BUILDING Se AgS TRADITION HOME COMFIORTHPR ODUCTS IMPORTANT SAFETY INSTRUCTIONS WARNING Any use of this appliance other than that recommended by the manufacturer in this owners manual may cause fire burns electric shock and or other serious injuries or death When using electrical appliances basic precautions should always be followed to reduce the risk of fire electric shock and inj
8. heat for any reason it will automatically turn all heater functions of the appliance off The appliance will have to be reset prior to continuing use To reset the overheat protection safety device turn all controls off and unplug the appliance Wait 10 minutes plug the appliance back in and turn on If the appliance continuously overheats please call our customer service department toll free at 1 877 744 3649 or email to service phoenixinno com Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEARTH TRENDS ________ BUILDING L SS TRADITION HOME COMFORUTUIPR ODUCTS TROUBLESHOOTING WARNING Turn off the appliance unplug and let cool for at least 15 minutes before attempting to service Only a qualified professional should attempt to service or repair the appliance IF YOU EXPERIENCE DIFFICULTIES PLEASE DO NOT RETURN THIS PRODUCT TO STORE For assistance with this appliance please call our customer service department toll free at 1 877 744 3649 or e mail us at service phoenixinno com FREQUENTLY ASKED QUESTIONS FAQS POSSIBLE CAUSE 1 The overheat protection device in the appliance has been triggered 2 Thermostat is set lower than room temperature PROBLEM No warm air is coming from the heater SOLUTION 1 Turn all controls off unplug the appliance allow to cool for at least 15 minutes plug back in and restart 2 Push temperature buttons on control panel or remote control t
9. n the tab out of the chamber See Maintenance Section See below for directions to use the remote control FIG 4 On Off Button N Fan Button S e Push button N to turn oji D e This is a High and Low electric fireplace on N S setting for the fan and I O art the heater Note Child Lock Feature R _ e Push this button R Q once to unlock the control panel functions and remote control functions P Please note that the heater will automatically lock the heater after 8 seconds without any operations that the fan will only Gel come on if the thermostat ci temperature is set above the room temperature ere TO et NOTE If the remote controller is lost please press on the Power switch on the control panel for 3 seconds the control will unlock after a short beep sound Celcius Fahrenheit Setting Button T e Push the button T to change the heat readout settings Temperature Buttons Increase Q and Decrease P e This electric fireplace is equipped with a thermostat Press the Temperature Button Q to increase the temperature Press the Temperature Button P to decrease the temperature The electric fireplace heater and fan will only turn on if the temperature setting is higher than the room temperature ESO Button Energy Savings Option U e Push this button U once to move the temperature setting easily to 68 degrees F 20 degrees C e Push the ESO Button U an additional tim
10. nce turn all controls OFF then remove the plug from the electrical outlet Always unplug the appliance when not in use 9 Connect to properly grounded outlets only The appliance comes equipped with a 3 prong grounding plug Do not attempt to cut the grounding prong Connect to properly grounded 120V outlets only This appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes with the current Canada CSA 022 1 Canadian Electrical Code U S A ANSI NFPA NO 70 National Electrical Code 10 Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fire or damage the appliance 11 To prevent a possible fire do not block air intakes or exhausts in any manner Do not use on soft surfaces like a bed where openings may become blocked 12 All electrical heaters have hot and arcing or sparking parts inside Do not use in areas where gasoline paint or flammable liquids are used or stored or where the appliance will be exposed to flammable vapors 13 When transporting or storing the heater take care to keep both the unit and power cord plug dry free from excessive vibration and away from heat sources 14 Use the heater only as described in this manual Any other use not recommended by the manufacturer may cause fire electric shock or injury to persons 15 Always plug heaters directly into a wall
11. o increase temperature 1 The overheat protection device in the appliance has been triggered 2 House circuit breaker has been tripped The appliance turns off and will not turn back on 1 Turn all controls off unplug the appliance allow to cool for at least 15 minutes plug back in and restart 2 Reset house circuit breaker 1 The overheat protection device in the appliance has been triggered The appliance does not turn on when the button is pushed to ON 1 Turn all controls off unplug the alliance allow to cool for at least 15 minutes plug back in and restart 1 Check the light B above the Power Switch on the control panel and ensure it is lit up red 2 House circuit breaker has been tripped Remote Control will not turn on the appliance when the power button is pushed ON 1 If the light is not lit up B on the control panel the appliance needs to be plugged in 2 Reset house circuit breaker Digital Temperature Screen is off 1 There has been no temperature adjustments for 1 Push Temperature Buttons on the Control Panel or Remote over 5 minutes Control to light up 1 The Child Lock feature R on the remote control settings on Control Panel or Remote 1 Push the Child Lock feature R on the remote contro to may be activated 2 The ESO feature U on the remote control may be activated Control cannot be adjusted Remote Control does not work 1 Low Batteries
12. outlet receptacle Never use with an extension cord or relocatable power tap outlet power strip 16 Do not attempt to burn wood or other materials in this heater 17 This appliance comes equipped with an overheat protection safety device Should the appliance begin to overheat for any reason the thermal cutout of appliance will be operated then all functions of the appliance shut down The appliance will have to be reset prior to continuing use To reset the overheat protection safety device turn all controls off plug the appliance back and turn on SAVE THESE INSTRUCTIONS Call 1 877 744 3649 for assistance or email us at service phoenixinno com HEARTH TRENDS ______ BUILDING 3S AQYSS m TRADITION HOME COMFIORUIPRODUCTS GROUNDING INSTRUCTIONS This heater is for use on 120 volts The cord has a plug as shown atA in Figure 65 1 An adapter as shown at C is available for connecting three blade grounding type plugs to two slot receptacles The green grounding lug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box The adapter should not be used if a three slot grounded receptacle is available Figure 66 1 Cepin maoa E ay E1 Vlg COVER OF GROUNDED i i OMET BOR m h iHi s ADAPTER gi a gt Ss hate iy a oe KE GRC NDING ee ta ny kp MEANS GACH Sp Ar Fh al re NOTE A 15AMP 120 Volts circuit is required
13. s away from the unit when in use Temperature Buttons Increase G and Decrease H e This electric fireplace is equipped with a thermostat Press the Temperature Button G to increase the temperature Press the Temperature Button H to decrease the temperature The electric fireplace heater and fan will only turn on if the temperature setting is higher than the room temperature The Temperature Digital Readout Screen I e This screen shows the current setting of the thermostat in Celcius or Fahrenheit degrees See Button L to adjust the setting to C or F e Press on the C F Button L on the control panel for 3 seconds and after a short beep sound the displayer will show the real room temperature for 5 seconds e This screen will turn off after 5 minutes if there is no temperature adjustments e The temperature light J indicates if the digital reading is in Fahrenheit and the temperature light K indicates the digital reading is in Celcius NOTE The fan will continue to work for several minutes when the heaters turns off This allows the infrared components inside the heater to cool down Control deal FIG 3 Using the Remote Control This heater includes a remote control To operate the appliance using the remote control ensure the red power light B is on Each remote control is shipped with a plastic tab inserted into the battery chamber to prevent damage and power loss Pls remove by pulling o
14. ury to persons including the following 1 Read the manufacturers instructions completely before using this appliance 2 This appliance will become hot when in use To avoid burns do not let bare skin touch hot surfaces The grill at the bottom of this heater in particular will become hot when the heater is active Keep combustible materials such as furniture pillows bedding paper cloth curtains etc at least 3 0 9m away from the front of the appliance Keep all items away from the sides and back of the appliance and take special care not to block the air intake or exhaust vents 3 Extreme caution is necessary when the appliance is used by or near children or invalids and whenever the heater is left operating and unattended 4 Do not operate the appliance if the power cord or plug has been damaged or the heater has been damaged or malfunctioned in any way Take the appliance to an authorized service facility for examination electrical or mechanical adjustment or repair 5 Do not use outdoors 6 This heater is not intended for use in bathrooms laundry areas and similar indoor locations Never locate heater where it may fall into a bathtub or other water container 7 Do not run the power cord under carpeting Do not cover the power cord with throw rugs runners or similar floor coverings Take care to position the cord away from high traffic areas and such that it can not be tripped over 8 To disconnect the applia
Download Pdf Manuals
Related Search
Related Contents
Invacare Personal Lift 1500 User's Manual Armstrong 00761123 Installation Guide Admin Bandit User Manual Sept 09 Part 8 V2 Progress Lighting P3981-09 Installation Guide Copyright © All rights reserved.