HarnesSysTM User Manual for the UPDATE WIRES Program
Contents
1. The contents of this page is subject to the limitations of use specified in the front page iv TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires Foreword This user guide is one of a set of user guides that make up volume 3 of the Harness user documentation Below is a description of the volumes of the Harness user documentation Volume 0 Overview Volume 1 Schematics Volume 2 Layout Drawing Volume 3 Wiring Volume 4 Parts Volume 5 Integration Volume 6 Management and Configuration Control Volume 7 Manufacturing Volume 8 Technical Publications The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 V Update Wires HARNESS Volume 3 Wiring About this User Guide This user guide describes the operation of the Update Wires program Below is a brief description of the sections that comprise this user guide Introduction This section provides general information about the input and output of the Update Wires program wire status bundle and wire issue It also contains diagrams of a typical bundle and wire life cycle Invoking the Update Wires Program This section describes the access path to the Update Wires program Prompts and Messages This section describes the prompts and messages displayed during update The Update Process This sectio2. TSN140 930359 Issue B Revision 0 21 Error and Information Messages Update Wires HARNESS Volume 3 Wiring Error and Information Messages The contents of this page is subject to the limitations of use specified in the front page E ORARE MENNAN Messages 22 TSN140 930359 Issue B Revision 0 HarnesSys Volume 3 Diagrams Formatting Guidelines Index A xxx trn file 1 xxx wupd file 3 ACD code Update rules 15 B bundle issue 2 7 bundle status 2 7 D data base locking 13 delete field content 1 19 R Release 2 16 S statistics 14 T Top Drawing 2 transaction files 12 U Update after Release 2 7 Update program invoking 11 W wire issue 2 wire key fields 2 wire status 2 Update rules 15 The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 23 Formatting Guidelines HarnesSys Volume 3 Diagrams Index Cont The contents of this page is subject to the limitations of use specified in the front page 24 TSN140 930359 Issue B Revision 0 Wire Update Manual Comment Form Your comments and suggestions help us determine how well we meet your needs and also help us improve the documentation Please fill out this form and fax it to HARNESS Project Manager Israel Aircraft Industries Engineering Center Department 2420 Fax 972 3 935 5049 Who Are You Project
3. to other SWD s still exist WIRELIST DASH THIS WIRE HAS LINK S TO THE FOLLOWING SWD S WARNING YOU CHANGED A The wire was previously modified but since it RECORD THAT WAS NEVER was never released the status was never changed RELEASED for the wire code A was overwritten by code ACD CODE WAS A IT REMAINS A A WARNING IN ADD WIRE A wire was added with missing connector data CONNECTOR FIELD MISSING ERROR YOU TRIED TO ADD AN The same record was previously added EXISTING RECORD DELETE THE RECORD WILL BE The record was marked for deletion and will be DELETED IN TIME OF RELEASE physically deleted when the record is released A Typical Bundle Life Cycle This section describes a typical life cycle of a bundle and the wires it contains The description is accompanied by graphic representation The bundles are represented by a divided rectangle The left cell of the rectangle contains the bundle status and the right cell its issue STATUS ISSUE Representation of Bundles wupd messages The contents of this page is subject to the limitations of use specified in the front page Introduction 4 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires The bundle status can be Define Open or Release The bundle issue can be NEW A B Z AA AB ZZ AAA BBB ZZZ J Issue ZZZ means that the bundle was deleted The wires are represented by rectan
4. manager Engineer wiring designer DBA Data entry personnel Programmer External user Other How Do You Use This Manual As an overview For comprehensive reference To learn the product or program For quick look up Other How do you like this manual 1 Poor 10 Excellent 12345678910 Does this manual cover all the topics you need Does it contain all the information you need about the topic Is the technical information accurate Is it easy to understand Is the order of the topics logical Can you easily find what you want Are there enough examples Are the examples helpful Is the manual easy to read page layout How Frequently do you use this manual Comments Name Company Address Phone Fax Date Thank you for your time
5. 6 lll ENGINEERING DIVISION Commercial Aircraft Group ISRAEL AIRCRAFT INDUSTRIES LTD HarnesSys User Manual for the UPDATE WIRES Program IAI Publication Number TSN140 930359 6 ll ENGINEERING DIVISION Commercial Aircraft Group ISRAEL AIRCRAFT INDUSTRIES LTD Notices The information contained in this manual is believed to be accurate and reliable However Israel Aircraft Industries Ltd IAI assumes no responsibility for any errors omissions or inaccuracies whatsoever Information in this document is subject to change without notice and does not represent a commitment on the part of Israel Aircraft Industries Ltd IAI The software and or data base described in this document are furnished under a license and or agreement The software and or data base may be used or copied only in accordance with the terms of such license and or agreement It is against the law to copy the software on any medium except as specifically allowed in the license and or nondisclosure agreement The purchaser may make one copy of the software for backup purposes No part of this document and or data base may be reproduced or transmitted in any form or by any means electronic or mechanical including photocopying recording or information storage and retrieval systems for any purpose other than the purchaser s personal use without the express written permission of IAI 1993 Israel Aircraft Industries Ltd All rights reserved 4 Pr
6. D WITH THE SIGN Cause in a field indicates that this field should be deleted This delete request cannot be included in a trn record with ACD A Action Change the ACD code to C or delete the Error and Information Messages The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 19 Error and Information Messages Update Wires HARNESS Volume 3 Wiring ERROR DEL WIRE ILLEGAL ACD CODE Cause The ACD code in the trn file is D but there is no wire to be deleted Action Correct the ACD code DELETE THE OLD WIRE Cause The open wire is deleted DELETE THE RECORD WILL BE DELETED IN TIME OF RELEASE Cause The program produced an open copy of the released wire with ACD code D The wire remains in the bundle until Release Upon Release it will be deleted ERROR YOU TRIED TO ADD AN EXISTING RECORD Cause The wire exists in the data base and the trn record ACD code A Action Change the ACD code to C or D or correct the wire key ERROR CHANGE ILLEGAL ACD CODE Cause The ACD code in the trn file is incompatible with the wire in the data base Action Correct the ACD code ERROR DELETE PART OR PIN NOT ALLOWED Cause A appears in the From To Connector or Pin field These fields may not be deleted Action Delete the CHANGE THE RELEASED RECORD IS
7. IRE DIAGRAM 1AISI IFROH PART PIN TRM CD COMIF1 F2 F3 ASSY SIGNAL EH LENGTH TO PART IPIN TRH CD COM F1 F2 F3 ASSY SYS SUB S DATE AND TIME RETAINED RUN LETTER REMOVE A LINK TO CURRENT SHD FROM HIRE NAME RD000000311C in WIRE LIST 31012 DASH 0001 THE WIRE HAS LINK S TO THE FOLLOWING SWD S DKC WD31012 B DKCEA0001 0001 WARNING YOU CHANGED A RECORD THAT HAS NEVER RELEASED ax ACD CODE WAS A IT REMAINS A DIF l 31012 0001 RD000000313C EOE dg Eod ltl THE WIRE NAME RD000000312C in WIRE LIST 31012 DASH 0002 ALREADY LINKED TO THE FOLLOWING SHD S DKC WD31012 B DKCEA0001 0001 31012 0002 RD000000313C 22 DKC WD31012 A AO 3101210002 RD000000315 1221 I DKC WD31012 A AIO TOTAL RECORDS PROCESSED 6 ADDED RECORDS 3 CHANGED RECORDS 1 DELETED RECORDS 0 LINKED RECORDS 1 UNLINKED RECORDS 1 ERROR RECORDS 0 UNCHANGED RECORDS 0 The xxx wupd File Structure The contents of this page is subject to the limitations of use specified in the front page Th e XXX wup d F l l e TSN140 930359 Issue B Revision 0 3 Introduction Update Wires HARNESS Volume 3 Wiring wupd messages Message Translation THE WIRE NAME IN WIRE A new link is established but this wire is also LIST DASH linked to another drawing ALREADY LINKED TO THE FOLLOWING SWD S REMOVE A LINK TO CURRENT A link from the wire to an SWD was removed SWD FROM WIRE NAME IN however other links
8. NING Indicates an operation that you the user are to perform Operations in a series are also numbered Indicates what you should see on the screen the computer s response Indicates a key on your keyboard Indicates a path to take This usually entails selecting a number of options from menus Indicates the end of the user guide The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 vii HarnesSys Volume 3 Diagrams Formatting Guidelines Contents Introduction dte tbe bla tete fede ede 1 The DOCK TS se eto tota ae ot ic o dte deed aas 1 Wire Slats RE 2 Bundle and Wire Issue 2 The XXX WUp File 3 WUpd MeESsSages MT 4 A Typical Bundle Life Cycle ssssss 4 Delimnaihe Bindl6 uo oe e Sh eter 5 Adding New WES sic aiio iei roo Roten 6 Changing Wires before Release ssssssssss 6 Releasing the Bundle eeseeesesssssss 6 CHENG INO VES PE 7 Deleting Wires cm 7 Canceling the Delete Request ccceesssccceeeteeeeeeeeeeeees 8 Deleting WIRES ei ger ea e eto iR ears 8 Releasing the Bundle yrs br od een a edt tg 9 Changing Wires etse ies ek Ne I ELLA AL 9 Invoking the Update Program 11 The Update Process sss 15 The contents of this page is subject to the limitations of use specified in the fro
9. THE SAME AS THE TRN RECORD Cause The wire in the data base and the trn record the wire after change are identical Therefore no change is to be performed The released wire remains unchanged in the data base Error and Information Messages The contents of this page is subject to the limitations of use specified in the front page Error and Information Messages 20 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires ATT YOU CHANGED A RECORD THAT WAS NEVER RELEASED Cause This open wire has no released copy in the data base ERROR DELETE IN FIELD VALUE Cause in a field indicates that this field should be deleted This delete request cannot be included in a trn record with ACD D Action Change the ACD code to C or delete the character ATT CHANGE YOU RE ENTERED CHANGED A DELETE RECORD Cause This wire is intended to be deleted from the data base ACD code D and the trn request cancels the delete intention DELETE YOU HAVE DELETED THE LAST UPDATE Cause The open wire is deleted CHANGE THE OPEN RECORD IS THE SAME AS THE TRN RECORD Cause The open wire and the trn record change request are identical Therefore no change is to be performed The open wire remains unchanged in the data base Error and Information Messages The contents of this page is subject to the limitations of use specified in the front page
10. d and the change is performed on the open wire The released wire will be changed during Release If the wire before the change in the xxx trn file is identical to the Released wire the system deletes the open wire The released wire remains unchanged and the open wire is deleted The Update Process TSN140 930359 Issue B Revision 0 17 The Update Process HARNESS Volume 3 Wiring Update Wires Error and Information Messages The xxx wupd file messages are listed below Messages beginning with dashes are for information only Therefore no action should be taken Error messages begin with asterisks ERROR IN DOCUMENT DEFINITION BASE NUMBER OR DASH Cause The bundle is not properly defined Action Check the bundle definition It should at least contain Base Number Dash and proper Effectivities ERROR ADD WIRE ONE OF BUNDLE DASH WIRE NAME IS MISSING Cause Part of the wire key is missing Action Make sure that all wire key fields in the message exist in the xxx trn file ERROR ADD WIRE CONNECTOR FIELD MISSING Cause From To Connector or Pin field is missing Action Make sure that these fields exist in the xxx trn file ERROR ADD WIRE ILLEGAL ACD CODE Cause This wire does not exist in the data base Therefore the only legal operation is Add Action Change ACD to A or correct the wire key ERROR ADD WIRE YOU CANNOT ADD A RECOR
11. e front page Introduction 8 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires Releasing the Bundle The user releases the bundle The system changes the bundle status to Released i The system deletes the released wires 2 3 and 4 and changes the status of the open wires 3 and 4 to Released gt 5 z gt e E Changing Wires The user changes wire number 4 in the schematic diagram performs wire integration and updates the data base with the xxx trn file slele gt 5 z Since this is the first Update after Release the bundle issue is incremented and and the bundle status becomes Open a gt The Change intention is registered in the ACD field of the open wire The Issue field of the open wire is filled with the new incremented bundle issue e B gt Jo it z The contents of this page is subject to the limitations of use specified in the front page H el easi ng th e B un di e TSN140 930359 Issue B Revision 0 9 Introduction Update Wires HARNESS Volume 3 Wiring Changing Wires The contents of this page is subject to the limitations of use specified in the front page Introduction 10 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires Invoking the Update Program To invoke the Update program proceed as follows 1 Select Project Wires 9 Update Project Open Import Query Part
12. epared by ell ENGINEERING DIVISION Commercial Aircraft Group ISRAEL AIRCRAFT INDUSTRIES LTD 6 lll ENGINEERING DIVISION Commercial Aircraft Group ISRAEL AIRCRAFT INDUSTRIES LTD HarnesSys User Manual for the UPDATE WIRES Program Pub Number TSN140 930359 Issue B Revision 0 December 1997 Update Wires HARNESS Volume 3 Wiring List of Effective Pages At present there is a total of 21 pages in this user guide as detailed below Pages Revision No Date Issued Title 0 31 12 97 li ix 0 31 12 97 1 21 0 31 12 97 Revision No 0 is the original printing of the user guide Issue B replaces issue A entirely Please make sure that your copy of this user guide contains the correct pages The contents of this page is subject to the limitations of use specified in the front page ii TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires Record of Changes and Revisions Doc Date Date Change Issued Title amp Description Change Signature No Made The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 fil Update Wires HARNESS Volume 3 Wiring Record of Changes and Revisions Cont Doc Change No Date Issued Title amp Description Date Change Made Signature
13. ery 25 wires IOTAL RECORDS PROCESSED 7 ADDED RECORDS 1 CHANGE RECORDS e DELETE RECORDS ERROR RECORDS 0 UN_CHANGE_RECORDS 4 These are statistics of the operations performed during Update According to this message the xxx trn file included 7 wire records One wire was added to the data base one wire was changed and one wire was deleted All the wire records in the xxx trn file were correct therefore ERROR RECORDS 0 4 records contained information identical to the wires in the data base therefore there is no need to change those wires in the data base check REPORT TRANSACTION FILE FRB lt user gt harness SDP private SDP wupd This is the exact name of the xxx wupd file produced by the update process lt user gt indicates the user s home directory z It is good practice to check this file in a separate window before confirming the update process To open the xxx wupd file select Document 9 Private Open gt Filter wupd 9 OK CJ Enter Y for update wires data in database PUES else E for exit Confirm the Update by pressing LY or cancels the update by pressing E fen If the contents of the xxx wupd file is not satisfactory correct the xxx trn file and resume the Update program In voking the Updati e Pri ogram The contents of this page is subject to the limitations of use specified in the front page Invoking the Update Progra
14. existing wire can not be deleted Error an existing wire can not be added noe The open wire is changed but its status remains A mH The open wire is deleted Error an existing wire can not be added again The released wire remains unchanged and the change is registered on a new open copy During Release the released wire PA is deleted and the status of the open wire 5 gt 9 is changed to R The released wire remains unchanged and the deleting intention is registered on a new open copy The released wire will I be deleted during Release The Updati e Process The contents of this page is subject to the limitations of use specified in the front page The Update Process 16 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Before Operation After CARA m gt eefe Update Wires Description Error an existing wire can not be added again The released wire remains unchanged and the change is performed on the open wire The released wire will be changed during Release If the wire before the change in the xxx trn file is identical to the Released wire the system deletes the open wire The released wire remains unchanged and the delete intention is registered on the open wire pem wo a The contents of this page is subject to the limitations of use specified in the front page Error an existing wire can not be added again The released wire remains unchange
15. fter Release the bundle issue is incremented and the bundle status becomes Open The Change intention is registered in the ACD field of the open wires 3 and 4 while the released wires remain unchanged The Update program fills the Issue of the open wires with the new incremented bundle issue The user deletes wires 1 and 5 from the schematic diagrams Then he performs wires integration and updates the data base with the xxx trn file The Delete requests are register of the open wires 1 and 5 The wires will actually be delet Changing Wires TSN140 930359 Issue B Revision 0 7 Introduction Update Wires Canceling the Delete Request l 1 A 2 A amp A 8 6 4 A 4 C 5 A Deleting Wires d z z m im ls D z E O gt Z gt B z z Nor O Bo gt z gt z m Bo A OO Q9 ePi oj Jo gt gt l l gt z e gt Zz m Canceling the Delete Request a Z z N HARNESS Volume 3 Wiring The user updates the data base with the xxx trn file from the previous stage or integrates the previous revision of the schematic diagram The system deletes the open wit The user deletes wire number 2 from the schematic diagram integrates the diagram and updates the data base with the xxx trn file The Delete request is registered the open wire 2 The contents of this page is subject to the limitations of use specified in th
16. gles divided into three cells ACD code Status and Issue ACD CODE STATUS ISSUE Representation of Wires The ACD code can be A add C Change or D delete The wire status can be Open or Release The wire issue can be NEW A B Z AA AB ZZ AAA BBB ZZZ The bundles are defined in the Top Drawing The wires are drawn in Schematic Diagrams and stored in the data base Instead of the Schematic Diagram and Wires Integration programs the Wires Data Base Modification program may be used Project Wires Build Transaction 9 Screen Mode Defining the Bundle DEFINE NEW The user defines the bundle using Configuration DEFINE NEN 9 Define For more information refer to the Configuration Control User Manual Defining the Bundle The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 5 Introduction Update Wires HARNESS Volume 3 Wiring Adding New Wires The user draws five new wires in schematic diagrams Then he integrates these diagrams and updates the data base with the xxx trn file produced by the integration or another program Z m l m gt gt O z m O z z The status of the bundle is changed from Define to Open e gt O z m 5 z m gt gt e Jo z m e Q E FT D we pi D yo m e Dn c e 2 e e p e e un e wa The user changes wire numbe
17. kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk The following files are in your PRIVATE directory File of wire records affected DKC WD31012 lt home gt wupd File of wire transactions DKC WD31012 a vii CPN File listing wires in SWD DKC WD31012 A trn tbl File of wire transactions in flat format DKC WD31012 A trn flt Log file screen messages DKC WD31012 A trn log Do you want to commit the changes to the database Enter C to COMMIT or S to STOP The following messages appear in this window L oRACLE_USER hrsdp I Cd This is the name of the data base containing the Wires Table L PROJECT spp Ee This is the project code CJ Attention The wire tables have been locked BM for updating The Update Wires program locks the data base until the update process is completed and it does not enable other users to update the data base during the lock Invoking the Update Program The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 13 Invoking the Update Program Update Wires HARNESS Volume 3 Wiring i e TRN PROCESS started for DOCUMENT PEUX SDP1702 002 This is the name of the current bundle This message appears for each bundle processed CJ total 7 wires done mm This is the number of wires contained in the xxx trn file for the current bundle If the bundle contains many wires the program notifies the user ev
18. m 14 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires The Update Process The Update process is visually depicted below Each wire is represented by a divided rectangle The left cell contains the ACD code of the wire The right cell contains the wire status The ACD code may have the following values A add new wire C change one or more fields of an existing wire or D delete an existing wire The wire status is either Open or Released ACD STATUS The figure below is arranged in a 4 column layout as follows e Before Indicates the wire ACD and Status in the data base before the update e Operation Indicates the operation to be performed on the wire add change or delete Therefore for every wire in the Before column there are 3 rows of Operation The operation code is the ACD field in the xxx trn file The operation name appears inside an arrow e After Indicates the wire ACD and Status in the data base after the update e Description Explanation of the update process Before Operation After Description EE gt EE This is the layout example The Update Process The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 15 The Update Process Update Wires HARNESS Volume 3 Wiring After Description E Add a new wire 9 Error a non existing wire can not be changed Before E 485 Error a non
19. n describes the Update process by presenting the wire in the data base before update the operation to be performed and the updated wire Error and Information Messages This section lists the error and information messages issued by the Update Wires program For each error message the cause of its appearance and the corrective action to be taken by the user are provided The contents of this page is subject to the limitations of use specified in the front page vi TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires Italic text Bold text Bold italics COURIE 3 R y A Wy o amp wY EI Conventions The following conventions are used in this guide Italic text is used to to indicate a word or phrase which has a special meaning with respect to Harness such as the name of a menu or option Italic text is also used for examples Smaller italic text is also used for notes and helpful hints these are also indicated by an icon see below Bold text represents the exact text that you the user are supposed to enter Bold italics is used for emphasis Text printed in Courier font represents text that appears on your screen Indicates a note Indicates an example Indicates a helpful hint Indicates additional information Indicates cautionary text or a warning Both types of text are framed in a box A Warning however is printed on a raster gray and has the title WAR
20. nt page TSN140 930359 Issue B Revision 0 viii HarnesSys Volume 3 Diagrams Formatting Guidelines Contents Error and Information Messages 19 The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 ix Formatting Guidelines HarnesSys Volume 3 Diagrams Contents Cont The contents of this page is subject to the limitations of use specified in the front page X TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires Introduction The Update Wires program applies the changes contained in a xxx trn transaction file to the Wires Table It can add new wires update fields of existing wires and delete wires n Eel Top Programs Update Wires Table Producing Program In Data Base Xxx trn Files Xxx wupd File The Wires Updating Process The XXX trn file The xxx trn file includes data on wires which may belong to different bundles and different schematic diagrams The data are e The wire key fields Effectivity Wire Bundle Dash Wire Name and Color e The change code A add C change or D delete e The fields required to perform the update For adding a new wire the xxx trn file should at least contain the wire key fields For changing a wire the xxx trn file must at least contain the key fields and the new values of the fields to be changed A field to be deleted
21. opy of the wire 2 The update intention becomes reality upon Release Bundle and Wire Issue Wire Status When performing Update for the first time after Release the bundle issue in Top Drawing is incremented and the bundle status becomes Open Further updates do not change the bundle status and issue The program fills the issue of the wires included in the current xxx trn file with the bundle issue This causes that different wires of the same bundle may have different issues The Issue filed may have the following values NEW A B Z AA AB ZZ AAA AAB ZZZ The contents of this page is subject to the limitations of use specified in the front page Introduction 2 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires J The user can define exceptions e g I or O These values are stored in the Projects Table When incrementing the Issue filed these values are skipped The XXX wupd File The xxx wupd is a detailed report of the update process It includes the wires before the change the wire after the change and the difference between them It also includes error messages Itis good practice to check this file before confirming the update operation Each wire includes the key fields the fields to be changed if applicable and the change request ACD code HIRES UPDATE FILE date 1997 09 29 15 ISU EFFECTIVITY BUNDLE DASH WIRE NAME GA SU COLRITF TS S1 2 S3 PRESSURE SEAL H
22. r number in a schematic diagram integrates the diagrams and updates the data base with the xxx trn file z Im z z m m z m The ACD code of the wire remains A since the bundle was not released yet z z A z m e e lol Jo fol fo Z m e Releasing the Bundle The user releases the bundle Z m i m z m The status of the bundle and wires becomes R but the issue remains unchanged m gt gt zZ m The system stores the data of the released bundle in a file for possible future retrieval e gt z m A z m gt z m e Adding New Wires The contents of this page is subject to the limitations of use specified in the front page Introduction 6 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Changing Wires Ble m jt z m e N gt d z z m m oo g O gt gt A A el f gt O D z gt z oO gt a f Deleting Wires l e n e O d m O i8 8 s 8 gt e gt gt D z m gt A e O d z gt z O gt e The contents of this page is subject to the limitations of use specified in the front page Update Wires The user changes wires 3 and 4 in the schematic diagrams Then he performs wires integration and updates the data base with the xxx trn file Since this is the first Update a
23. s Wires Close Quit Document Configuration Mi D gt Build Transaction gt Ctrl Z Update F10 Query Report The function displays the following window which already contains the The contents of this page is subject to the limitations of use specified in the front page Invoking the Update Program TSN140 930359 Issue B Revision 0 11 Invoking the Update Program Update Wires HARNESS Volume 3 Wiring names of all the transaction files in your private directory E DCR Select Transaction File Transaction files DKC WD31012 A trn Selection DKC WD31012 A trr 2 Click on the desired xxx trn file and on OK The function displays the In voking the Updati e Pri ogram The contents of this page is subject to the limitations of use specified in the front page Invoking the Update Program 12 TSN140 930359 Issue B Revision 0 HARNESS Volume 3 Wiring Update Wires Wires Update window DCR 88 DKC WD31012 A trn running userhome ddnd r5a 02 hp integrate d out DCR 88 DKC WD31012 A trn DCR DKC WD31012 A Total of records read kKAkkXkKkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk The following lines summerize the updating of vires data in the database TOTAL No of RECORDS PROCESSED 2 No ADDED RECORDS No CHANGED RECORDS No DELETED RECORDS LINKED RECORDS UNLINKED RECORDS UNCHANGED RECORDS ERROR RECORDS XK kkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkkk
24. should contain the character For deleting a wire the xxx trn file must at least contain the key fields However if the xxx trn file is prepared by the Wires Integration program it always contains all wire fields Introduction The contents of this page is subject to the limitations of use specified in the front page TSN140 930359 Issue B Revision 0 1 Introduction Update Wires 8 HARNESS Volume 3 Wiring The wire key fields Effectivity Wire Bundle Dash Wire Name and Color cannot be changed The only way to change them is to delete the wire and add a new wire with the new key fields HIRE KEY 2 44 BUNDLE 1221 DASH 001 HIRE HAHE JP00005 TYPE FAH A TYPE TO CONNEC 123YJ TO PIN 74 ACD C STATUS O LCD 1993 03 28 12 9 31 WIRE KEY 245 BUNDLE 1221 DASH 001 WIRE NAHE JPO00006 TYPE FAH A TYPE TO CONNEC 123YJ TO PIN 65 ACD C STATUS O LCD 1993 03 28 12 9 31 Wire Status XXX trn File Portion During operation the Update program alters the following wire fields e Wire status e Bundle issue e Wire issue Wires in the data base are either open or released the Status field contains O or R Released wires may be used by external users e g production departments Open wires may be used by external users only after an authorized user Releases them In order to allow notifying the production departments wires are updated in two stages 1 The update intention add change or delete is registered on an open c
Download Pdf Manuals
Related Search