ET863 USER`S MANUAL - IBT Technologies Inc.
Contents
1. Panel Type 0 640x480 18bit TFT 1 800x600 18bit TFT 2 1024x768 36bit TFT 3 1280x1024 36bit TFT 41640x480 16bit DSTN 5 800x600 16bit DSTN 6 1024x768 16bit DSTN 7 1024x768 18bit 1CH LVDS 8 640x480 18bit TFT 9 800x600 18bit TFT A 1024x768 18bit TFT B 1280x1024 18bit TFT C 1400x1050 36bit 2CH LVDS D 800x600 16bit DSTN E 1024x768 16bit DSTN F 1280x1024 16bit DSTN Power Supply Type This field that power supply type that the system is using By default this field is set to AT SSS _ _ _____ _o gt 2 2 ET863 User s Manual 21 DRIVERS INSTALLATION aS OnChip USB The default setting of this filed is Enabled to enable the USB function OnChip Keyboard Support Enable this if you are using a USB keyboard OnChip Sound This field enables or disables the on board audio function CPU to PCI Write Buffer This controls the CPU write buffer to the PCI bus If this buffer is disabled the CPU writes directly to the PCI bus The default is Enabled PCI Dynamic Bursting This option controls the PCI write buffer If this is enabled then every write transaction on the PCI bus goes straight to the write buffer Burst transactions are then sent on their way as soon as there are enough to send in a single burst PCI Master 0 WS Write This function determines whether there s a delay before any writes to the PCI bus If this is enabled then writes to the PCI bus are executed immediately2. CPU Voltage 1 05V 1 825V CPU External 100 133Mhz Clock Chipset VIA Pro Savage TwisterT PN133T VT82C686B Chipset North Bridge VT8606 552 Pin PBGA South Bridge VT82C686A B 352 Pin BGA BIOS Award BIOS Support ACPI Function Cache 128K Level 1 64K Level 2 CPU integrated On Board VGA VT8606 with Integrated Savage4 AGP4x Graphic 8 16 32 MB frame buffer using system memory Integrated 2 channel 110MHZ LVDS interface LAN Realtek RTL8100BL Single Chip Ethernet Controller 10 100 Base T support Sound VT82C686A B Built in Sound controller AC97 Codec VIA1611A Line out Line in Mic Memory Type Ix SODIMM 3 3V Max 256MB Support PC100 PC133 SO DIMM Module Super I O VIA VT82C686A B IrDAx1 Parallel x1 COM1 2 RS 232 FDC 2 88MB 3 Mode support Hardware monitor 2 thermal inputs 4 voltage monitor inputs VIDO 4 RTC CMOS VT82C686A B Built in Local Bus IDE VT82C686A B Built in IDE1 IDE2 ETX Interface Connectors x 4 For PCI bus USB Sound VGA LCD COM1 COM2 LPT Floppy IrDA Mouse Keyboard IDE1 IDE2 Ethernet ISA USB Supports 4 ports transfer rate up to 12Mb s Board Size 95mm x 114mm 3 74 x 4 5 ET863 User s Manual 3 INTRODUCTION Dimensions e o RS 111 6 RV 24 KA ort E T 53 3 ko 0 95 om 92 5 e ES e 87 5 H 45 9 np 11 7
3. Le 111 H 114 gt O Location peg 91 0 0 5mm O Location peg 0 7 0 5mm All dimension without tolerance 0 2mm O CN2 CN1 CN4 CN3 4 Top View 4 ET863 User s Manual INTRODUCTION Connectors on ET863 TL ENECSA BUS ita dat dit 6 2 CN2 IDE 1 IDE 2 Ethernet MiSC ooonoconnonncnnnonnnnnonnnnnonacnonarnnos 7 3 CN3 PCI Bus USB Sound coccoccccccnoconnoncnnnonannnonacnnonarnnonaonnonnonaon 8 4 CN4 VGA LCD Video COM COM2 LPT Floppy IrDA Moise Keyboard ab 8 3 32 FDD CONE IOE a a aia 9 See ET863 User s Manual 5 INTRODUCTION a __ _ _ gt P E EEE EA 1 CN1 ISA Bus Signal Signal Signal Signal GND GND VCC VCC SD14 SD15 SA6 IRQ5 SD13 MASTER SA7 IR06 SD12 DREQ7 SA8 IRQ7 SD11 DACK 7 SA9 SYSCLK SD10 DREQ6 SA10 REFSHJ SD9 DACK 6 SA11 DREQ1 SD8 DREQ5 SA12 DACK 1 MEMW DACK 5 GND GND MEMR DREQO SA13 DREQ3 LA17 DACK 0 SA14 DACK 3 LA18 IRQ14 SA15 IORJ LA19 IR015 SA16 10W LA20 IRQ12 SA18 SA17 LA21 IRQ11 SA19 SMEMR LA22 IRQ10 IOCHRD Y AEN LA23 1016 VCC VCC GND GND SDO SMEMW SBHE M16 SD2 SD1 SAO OSC SD3 NOWSJ SA1 BALE DREQ2
4. General Adapter Monitor Performance Color Management Hj Standard PCI Graphics Adapter VGA Adapter Driver information Manufacturer Standard display types Software version 4 0 Current files vaa dry vdd ET863 User s Manual 39 DRIVERS INSTALLATION 3 The Update Device Driver Wizard will appear Click Next to search for the VGA drivers Update Device Driver Wizard This wizard searches for updated drivers for Standard PCI Graphics Adapter VGA A device driver is a software program that makes a hardware device work Upgrading to a newer version of a device driver may improve the performance of your hardware device or add functionality 4 Click Next to continue the search for the drivers Update Device Driver Wizard What do you want Windows to do Search for a better driver than the one your device is using now Recommended i Display a list of all the drivers in a specific location so you can select the driver you want lt Back Next gt Cancel 40 ET 863 User s Manual DRIVERS INSTALLATION 5 Click on the Specify a location checkbox and type the location path as E VIA VIA8606 Win9x This is assuming that E is your CDROM drive and you are installing drivers for Windows 9x Please select other subdirectories if you are using other operating systems Update Device Driver Wizard Windows will search for updated drivers in its dri
5. When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices eae 12 ET863 User s Manual DRIVERS INSTALLATION Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Advanced BIOS Features Advanced Chipset Features Integrated Peripherals Power Management Setup PnP PCI Configurations PC Health Status Frequency Voltage Control Load Fail Safe Defaults Load Optimized Defaults Set Supervisor Password Set User Password Save amp Exit Setup Exit Without Saving ESC Quit F10 Save amp Exit Setup NY gt Select Item Time Date Hard Disk Type The section below the setup items of the Main Menu displays the control keys for this menu At the bottom of the Main Menu just below the control keys section there is another section which displays information on the currently highlighted item in the list Note If the system cannot boot after making and saving system changes with Setup the Award BIOS supports an override to the CMOS settings that resets your system to its default Warning It is strongly recommended that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability Changing the defaults could cause the system to become unstable and crash in
6. COMP Y NC Signal C Signal VCC VCC VCC NC NC DINST NC GND GND GND NC GND GND Note JP1 and S1 are for manufacturing test use only ET863 User s Manual 9 INTRODUCTION This page is intentionally left blank ey 10 ET863 User s Manual DRIVERS INSTALLATION BIOS Setup This chapter describes the different settings available in the Award BIOS that comes with the CPU card The topics covered in this chapter are as follows BIOS Intro ducto ati 12 PILONS ni i o tops cdt allas 12 Standard CMOS Setup oococcccccnconcnnnnnononncanonoconcnnonorannonencnacnonos 14 Advanced BIOS Features oooococccnconnnnnnnnnononnonccnnocnononanonocncnono 17 Advanced Chipset Features oococonnonnonnnonononnnnnanncnanonononncnono 20 Integrated Peripherals eeesessecseeesseteseeeeesseeeeeeesseeeeees 23 Power Management Setup occocccococnonononnnnnanononnrncanononncnnanononnos 25 PNP PCI Configurations cccocconccconnnnononnnnnonnonnnnnannonononaronnaneno 29 PC Health Status iii oil liada 30 Frequency Voltage Control ooconccocicicnncncnonononnncnoncnncnnanononnos 31 Load Fail Safe Defaults ooioncnnnnonnnnnonnononnnnnonnonononorocnanono 32 Load Setup Default p 32 Set Supervisor User PassWold oooonococicnnnnnnnnonnononnconinnonananooos 32 Save Exit Sepi uturatidn a bre AE hast EEEE 32 Exit Without Saving bits aein 32 ET863 U
7. OFOh Clear Math Coprocessor Busy Signal OF 1h Reset Math Coprocessor 1F0h 1F7h IDE Interface 278 27F Parallel Port 2 LPT2 2F8h 2FFh Serial Port 2 COM2 2B0 2DF Graphics adapter Controller 378h 3FFh Parallel Port 1 LPT1 360 36F Network Ports 3B0 3BF Monochrome amp Printer adapter 3C0 3CF EGA adapter 3D0 3DF CGA adapter 3FO0h 3F7h Floppy Disk Controller 3F8h 3FFh Serial Port 1 COM1 ET863 User s Manual 49 APPENDIX B Interrupt Request Lines IRQ Peripheral devices use interrupt request lines to notify CPU for the service required The following table shows the IRQ used by the devices on board Function System Timer Output Keyboard Interrupt Cascade Serial Port 2 Serial Port 1 Reserved Floppy Disk Controller Parallel Port 1 Real Time Clock Reserved Reserved Reserved PS 2 Mouse 80287 Primary IDE Secondary IDE 50 ET863 User s Manual
8. SD4 SA2 TC SD5 IRQ9 SA3 DACKJ 2 SD6 SD7 SA4 IR03 1OCHK RSTDRV SA5 IRQ4 GND ET863 User s Manual GND INTRODUCTION 2 CN2 IDE 1 IDE 2 Ethernet Misc Pin Signal Pin Signal Pin Signal Pin Signal 1 GND 2 GND 51 SIDEIOW 52 PIDE IORJ 3 5V SB 4 PWGIN 53 SIDEDRQ 54 PIDEIOW 5 PS ON 6 SPEAKER 55 SIDED15 56 PIDE DRQ 7 PWRBTNJ 8 BATT 57 SIDEDO 58 PIDED15 9 KBINH 10 LILED 59 SIDED14 60 PIDE DO 11 NC 12 ACTLED 61 SIDE D1 62 PIDE D14 13 NC 14 SPEEDLED 63 SIDED13 64 PIDE D1 15 NC 16 NC 65 GND 66 GND 17 VCC 18 VCC 67 SIDE D2 68 PIDE D13 19 OVCRJ 20 GPCSJ 69 SIDED12 70 PIDE D2 21 EXTSMI 22 NC 71 SIDE D3 72 PIDE D12 23 SMBCLK 24 SMBDATA 73 SIDE D1 74 PIDE D3 25 SIDE CS3 26 N C 75 SIDE D4 76 PIDE D11 27 SIDE CS1J 28 DASP S 71 SIDE D10 78 PIDE D4 29 SIDE A2 30 PIDE_CS3 79 SIDE D5 80 PIDE D10 31 SIDE AO 32 PIDE CS1J 81 VCC 82 VCC 33 GND 34 GND 83 SIDE D9 84 PIDE D5 35 NC 36 PIDE_A2 85 SIDE D6 86 PIDE D9 37 SIDE Al 38 PIDE A0 87 SIDE D8 88 PIDE D6 39 SIDEINTRO 40 PIDE Al 89 N C 90 N C 41 N C 42 N C 91 RXD 92 PIDE D8 43 SIDE AKJ 44 PIDE INTRO 93 RXD 94 SIDE D7 45 SIDE RDY 46 PIDE AK 95 TXD 96 PIDE D7 47 SIDE JOR 48 PIDERDY 97 TXD 98 HDRSTJ 49 VCC 50 VCC 99 GND 100 GND ET
9. but not all modern PCs have additional external cache memory When the CPU requests data the system transfers the requested data from the main DRAM into cache memory for even faster access by the CPU These items allow you to enable speed up memory access or disable the cache function By default these items are Enabled el a I _ o o RR e ET863 User s Manual 17 DRIVERS INSTALLATION Se CPU L2 Cache ECC Checking This field enables or disables the ECC Error Correction Checking checking of the CPU level 2 cache The default setting is Enabled Quick Power On Self Test When enabled this field speeds up the Power On Self Test POST after the system is turned on If it is set toEnabled BIOS will skip some items First Second Third Boot Device These fields determine the drive that the system searches first for an operating system The options available include Floppy LS ZIP HDD 0 SCSI CDROM HDD 1 HDD 2 HDD 3 LAN and Disable Boot Other Device These fields allow the system to search for an operating system from other devices other than the ones selected in the First Second Third Boot Device Swap Floppy Drive This item allows you to determine whether or not to enable Swap Floppy Drive When enabled the BIOS swaps floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A By default this field is set to Disabled Boot Up Floppy Seek When enabled the BIOS will seek whether or not the
10. installation 1 Insert the CD that comes with the CPU card and the screen below would appear Click VIA Chipsets on the left side Anside This fi 34 ET863 User s Manual DRIVERS INSTALLATION 3 When the Welcome screen appears click Next Wekens to the Wit Services Pack Setup prog Tyr program yal Patel VIA Service Pack on your lt conais le shoggy coconnanded that pau ssk dl ndave piagam baie irreg hi Seto pogam Dick Cencel to qu Setup ad ihar chise ay pogana vat have mawa Cick New to contnue uth the Setup pogan WARNING Tiis progam ir protected by oopynghi tot and Hensel tasis Unashotzed repioduction a detibufen of ve mogen o an Portion olit ma resak in revere coal and enms penaber and wi be prosecuted ta the makinn od t parido undar Ge cuca 4 Click Next to agree with the license agreement statement and to continue A VIA Service Peck VIA Sargs Pack VIA 4 1 Lo LIS VIA Techrmiog es Ire able of Contents Shout VIO din 1 Selling Up Upeiete Technical Support Special Hote WirFact AGP VGA users oy Qicting es mesos pou have reed ard ageet wilt the licence egiesment and README Dick Noto decir and Est q us E zz A lt K mm OC a A EEC 44 ET863 User s Manual 35 DRIVERS INSTALLATION ee 5 Select the Setup Mode and click Next to continue Ciok to esbis Normally or Quickly iretal 6 Click Next to install the drivers listed Setup Loamponents E This
11. with zero wait states as soon as the PCI bus is ready to receive data PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 PCl 2 Access 1 Retry This BIOS feature is linked to the CPU to PCI Write Buffer Normally the CPU to PCI Write Buffer is enabled All writes to the PCI bus are as such immediately written into the buffer instead of the PCI bus This frees up the CPU from waiting till the PCI bus is free The data are then written to the PCI bus when the next PCI bus cycle starts AGP Master 1 WS Write Read When enabled a single wait state is used when writing reading to the AGP bus When disabled a 2 wait state is used For optimal performance set this to enabled For improved stability set it to disabled ee ee 22 ET863 User s Manual DRIVERS INSTALLATION ee Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals On Chip IDE Channel 0 Enabled ITEM HELP On Chip IDE Channel 1 Enabled Menu Level DE Prefetch Mode Enabled DE Primary Master PIO Auto DE Primary Slave PIO Auto DE Secondary Master PIO Auto DE Secondary Slave PIO Auto DE Primary Master UDMA Auto DE Primary Slave UDMA Auto DE Secondary Master UDMA Auto DE Secondary Slave UDMA Auto nit Display Fir
12. _ _ _ _ _ _ __ _ gt _e_ 4 ET863 User s Manual 15 DRIVERS INSTALLATION A A z oem gt I QQRRIEI TI UEE Video This field selects the type of video display card installed in your system You can choose the following video display cards EGA VGA For EGA VGA SEGA SVGA or PGA monitor adapters default CGA 40 Power up in 40 column mode CGA 80 Power up in 80 column mode MONO For Hercules or MDA adapters Halt On This field determines whether or not the system will halt if an error is detected during power up No errors The system boot will not be halted for any error that may be detected All errors Whenever the BIOS detects a non fatal error the system will stop and you will be prompted All But Keyboard The system boot will not be halted for a keyboard error it will stop for all other errors All But Diskette The system boot will not be halted for a disk error it will stop for all other errors All But Disk Key The system boot will not be halted for a key board or disk error it will stop for all others K _ lt _ _ __ ____ A 16 ET863 User s Manual DRIVERS INSTALLATION Advanced BIOS Features This section allows you to configure and improve your system and allows you to set up some system features according to your preference Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features Virus Warning Disabled ITEM HELP CPU Internal Ca
13. freely Save amp Exit Setup This option allows you to determine whether or not to accept the modifications If you type Y you will quit the setup utility and save all changes into the CMOS memory If you type N you will return to Setup utility Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session Typing Y will quit the Setup utility without saving the modifications Typing N will return you to Setup utility SSS SSS ey 32 ET863 User s Manual DRIVERS INSTALLATION Drivers Installation This section describes the installation procedures for software and drivers under the Windows 98 Windows NT 4 0 and Windows 2000 The software and drivers are included with the CPU card If you find the items missing please contact the vendor where you made the purchase The contents of this section include the following VIA 4 in 1 Drivers Installation ooccconnnncccninnccncnncccnnono 34 VGA Drivers InstallatiON ooncccnnnccccnnnnccncncccnnnnonicinns 39 LAN Drivers Installation oooooncccnnnnocccnnnnccnnnicccnnnnnnanonns 42 Sound Drivers Installation ooccccconncccnnnnocncnnacnnnnnnnnos 46 ET863 User s Manual 33 DRIVERS INSTALLATION VIA 4 in 1 Drivers Installation Before installing the drivers for VGA LAN and Audio install the VIA 4 in 1 drivers first Follow the instructions below to complete the
14. 863 User s Manual 7 INTRODUCTION as 3 CN3 PCI Bus USB Sound Signal Signal Signal GND GND VCC PCICLK3 PCICLK4 PAR GND GND GPERRJ PCICLK1 PCICLK2 PMEJ REQJ3 GNTJ3 LOCK DEVSELJ GNTJ2 3V TRDYJ USB30 REQJ2 GNTJ1 IRDYJ STOPJ REQJ 1 3V FRAMEJ USB21 GNTJO N C GND GND VCC VCC AD16 CBEJ 2 SERIRQ REQJO AD17 USB31 ADO 3V AD19 AD18 AD1 AD2 AD20 USBOO AD4 AD3 AD22 AD21 AD6 AD5 AD23 USB10 CBFJO AD7 AD24 CBE 3 AD8 AD9 VCC VCC GND GND AD25 AD26 AD10 AUXAL AD28 USBO1 AD11 MIC AD27 AD29 AD12 AUXAR AD30 USB11 AD13 ASVCC PCIRSTJ AD31 AD14 SNDL IRQY IRQZ AD15 ASGND IRQW IRQX CBE 1 _ _ _ _ _ __ _ u ET863 User s Manual SNDR GND GND INTRODUCTION 4 CN4 VGA LCD Video COM COM2 LPT Floppy IrDA Mouse Keyboard Signal GND R HSY VSY NC TYCLK NC TYCLK NC GND GND TY1 TY2 TY1 TY2 GND GND TYO TYO GND TXCLK TXCLK GND TX1 TX1 VCC LTGIOO JILi_CLK BLON BIASON DIGON
15. Compatible with PCI Local Bus Revision 2 1 specification IEEE 802 3u Auto Negotiation for automatic speed selection Supports Full Duplex Half Duplex Operation Provides 32 bit bus mastering data transfer Supports 10Mbps and 100Mbps operation in a single port The following section describes the installation driver procedure for Windows 98 ___ _ _ _ _ _ _ M M 42 ET863 User s Manual DRIVERS INSTALLATION ee Installing LAN Drivers for Windows 98 This section describes the procedure to install Windows 98 drivers for Realtek RTL8100BL PCI Fast Ethernet controller 1 Under Windows 98 click Start then Settings then Control Panel Double click System Properties Under System Properties click Device Manager then Other Properties Remove the two PCI Ethernet Controller and click Refresh Denard Duva Menage Hediste Prrffer Periotnsnce E N vn devices by pe F View devices by connector baller Sp Had dirk cmrobu S Keosd Ps Mentor gt Howe LE car adagio ta Y Othe devices PO Eihera Conois mF Pate COMS LPT Sound video and g re cor DS 2 EEE AAA 2 A ET863 User s Manual 43 DRIVERS INSTALLATION Ce a o ho 2 Windows will start to search for the new drivers for the Ethernet controllers In the Add New Hardware Wizard click Next 3 Now select Search for the best driver for your device Recommended and click Next FEE AAA nn 44 ET863 User s Man
16. D disc to the CD ROM drive The CD ROM autoruns and displays the selections available Click on VIA Chips Driver and the following window appears Click VIA 686A B PCI Multimedia Audio Driver incide This CI Inehidie VIA registry INT driver VLA AOP YD sitet IIA ATAN 2 When the Welcome screen appears click Next to proceed with the audio driver installation agg Welcoms to the Vit PC Audio Driver Setup Progran Sap en This program valinta via PEI Fado Dar Sako Progam on pour computa le strong oconemanced that pou sst A nda progre babie ung ihi Seto pio gem Click Cancel to quk Seip sod then chee ay pogana yai have nin Cick Hest to continue wth the Setup program WARNING Tres progam de by co lew and Pheinstional pestes nia a Unedhotzed reproduction a debuten of hie mogen ot ary potion of it map resak in severe chu and crimina perez and vl be pipsaculad to the mana tor passie under li EA sm 46 ET863 User s Manual DRIVERS INSTALLATION 3 The Select Components window will appear Click Next to install the audio driver instal or Aemave the Auda Driver E Isiah Remave t Hack Cancel 4 After the necessary files are copied click Finish Seo has finished coco des tn pour compute Betts you Cart Les Ihe Progen pou mut aE ROME Of your campus C Ma yal stat my conpurer eter Reomave any debs bom thay deso and than cidi Fish lo comp s actu 5 When W
17. ET863 VIA C3 Eden Processor ETX CPU Module USER S MANUAL Version 1 0 Acknowledgments Award is a registered trademark of Award Software International Inc PS 2 is a trademark of International Business Machines Corporation Microsoft Windows is a registered trademark of Microsoft Corporation All other product names or trademarks are properties of their respective owners ii ET 863 User s Manual Table of Contents Introducti ON isaac 1 Product Description cooooooocccnncccnononanannnnnnnnnncnnonnnnnncnccnnnnnnns 1 Check tete Leona 2 Specifications cece cio re see te Aiea dns og 3 DIMENSIONS rita ia 4 Connector Locations on ET863 ooooonccnnccnnnccnnnoccnuncnnnncnnnos 5 BIOS SU Dinars 11 Drivers InstallatiON conccoonncccnancconancccnananonanananana 33 VIA 4 in 1 Drivers Installation ooccccocccnnnccnnnccnnnocnnnicnns 34 VGA Drivers InstallatiON oocccncccnnnccnonccnnininnnicnnnncnns 39 LAN Drivers Installation ocoooccnncccnnnccnnnccnninononicnnaninns 42 Audio Drivers InstallatiOK occconccnnnccnnnccnnnccnnnccnnnicnno 46 A Gees iaaa taakaaka 49 A I O Port Address Map occccooooccnnonocnncnononanononananccnnnnnanoss 49 B Interrupt Request Lines IRQ ccccccccceceeeeesetneeeeeees 50 ET863 User s Manual iii This page is intentionally left blank SSS ey iv ET863 User s Manual INTRODUCTION Introduction Product Description ET863 is an ET
18. PU clock and PCI clock You can also use this parameter to overclock your system However it is important to note that overclocking the system CPU can cause your system to become unstable or crash Ser ET863 User s Manual 31 DRIVERS INSTALLATION SS Load Fail Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features Load Setup Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features Set Supervisor User Password These two options set the system password Supervisor Password sets a password that will be used to protect the system and Setup utility User Password sets a password that will be used exclusively on the system To specify a password highlight the type you want and press lt Enter gt The Enter Password message prompts on the screen Type the password up to eight characters in length and press lt Enter gt The system confirms your password by asking you to type it again After setting a password the screen automatically returns to the main screen To disable a password just press the lt Enter gt key when you are prompted to enter the password A message will confirm the password to be disabled Once the password is disabled the system will boot and you can enter Setup
19. Phoenix AwardBIOS CMOS Setup Utility PC Health Status CPU Warning Temperature 80 C 176 F ITEM HELP Current System Temperature 34 C 95 F Current CPU Temperature 28 C 82 F Vcore V 1 45V 2 5V 2 47V 3 3 V 3 34V 5 V 5 05V 12 V 12 09V CPU Warning Temperature This field sets the temperature threshold that when reached the system would give an audible warning The default is 80 C Temperatures Fan Speeds Voltages These fields are the parameters of the hardware monitoring function feature of the CPU card The values are read only values as monitored by the system and show the PC health status 8s 30 ET863 User s Manual DRIVERS INSTALLATION Eo o o A A e Frequency Voltage Control This section shows the user how to configure the processor frequency Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control VIA C3 Clock Ratio Default ITEM HELP Auto Detect DIMM PCI Clk Disabled Menu Level Spread Spectrum Disabled Host CPU PCI Clock Default VIA C3 Clock Ratio The clock ratio is set as Default Auto Detect DIMM PCI Clk This field enables or disables the auto detection of the DIMM PCI clock The default setting is Disabled Spread Spectrum This field sets the value of the spread spectrum The default setting is Disabled This field is for CE testing use only Host CPU PCI Clock The Host CPU PCI Clock has a default setting of Default which automatically detects the systems host C
20. Press Enter System Configuration Data ESCD when you PCI VGA Palette Snoop Disabled exit Setup if you have Enabled installed a new add on Assign IRQ for VGA hable and the system Assign IRQ for USB Enabled reconfiguration has caused such a serious conflict that the OS cannot boot PNP OS Installed Enable the PNP OS Install option if it is supported by the operating system installed The default value is No Reset Configuration Data This field allows you to determine whether to reset the configuration data or not The default value is Disabled Resources Controlled by This PnP BIOS can configure all of the boot and compatible devices automatically with the use of a use a PnP operating system such as Windows 95 PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This field allows you to set whether or not MPEG ISA VESA VGA cards can work with PCI VGA When this field is enabled a PCI VGA can work with an MPEG ISA VESA VGA card When this field is disabled a PCI VGA cannot work with an MPEG ISA VESA card Assign IRQ for VGA USB By default this fields are Enabled _ _ _ _ _ _ _ _ _ _ _ gt gt gt lt lt _ _ _ gt __ Qu ET863 User s Manual 29 DRIVERS INSTALLATION ee PC Health Status This section shows the parameters in determining the PC Health Status These parameters include temperatures fan speeds and voltages
21. X CPU module based on the VIA C3 Eden processor ETX stands for Embedded Technology extended a technology or form factor that offers flexible time to market solution enabling product development time to shrink from four months to just four weeks It also features low power consumption and low heat emission eliminating the need for a CPU fan System memory is provided by a SO DIMM socket that supports up 256MB of SDRAM memory The Award BIOS facilitates easy system configuration and peripheral setup Other advanced features of ET863 includes On Board Savage AGP4X Graphics LVDS Realtek RTL8100BL LAN Controller Built in Audio with AC97 Codec TV out 4 USB ports The ET863 has four board to board high density interface connectors for I O signals that plug onto baseboards specific to customer s applications ETX embedded solutions provide fast time to market through the interchangeability and scalability of both the ETX module and the baseboard SSS ee ET863 User s Manual 1 INTRODUCTION Checklist Your ET863 package should include the items listed below e The ET863 CPU Module e This User s Manual e CD containing the following e Chipset Drivers e Flash Memory Utility e 1FDD cable _ _ _ _ _ _ _ _z ay 2 ET863 User s Manual INTRODUCTION Specifications Product Name ET863 Form Factor ETX CPU Type VIA C3 Samuel 2 or Ezra or Eden Processor EBGA
22. che Enabled Menu Level External Cache Enabled CPU L2 Cache ECC Checking Enabled Allows you choose Quick Power On Self Test Enabled the VIRUS warning First Boot Device Floppy feature for IDE Hard Second Boot Device HDD 0 Disk boot sector Third Boot Device CDROM Protection Hanis Boot Other Device Enabled funtion is nabled and someone Swap Floppy Drive Disabled attempt to write Boot Up Floppy Seek Disabled data into this area Boot Up Numlock Status On BIOS will show a Gate A20 Option Fast warning message Typematic Rate Setting Disabled on screen and Typematic Rate chars Sec 6 alarm beep Typematic Delay Msec 250 Security Option Setup OS Select For DRAM gt 64MB Non OS2 Video BIOS Shadow Enabled C8000 CBFFF Shadow Disabled CC000 CFFFF Shadow Disabled D0000 D3FFF Shadow Disabled D4000 D7FFF Shadow Disabled D8000 DBFFF Shadow Disabled DC000 DFFF Shadow Disabled Small Logo EPA Show Enabled Virus Warning This item protects the boot sector and partition table of your hard disk against accidental modifications If an attempt is made the BIOS will halt the system and display a warning message If this occurs you can either allow the operation to continue or run an anti virus program to locate and remove the problem CPU Internal Cache External Cache Cache memory is additional memory that is much faster than conventional DRAM system memory CPUs from 486 type on up contain internal cache memory and most
23. e It is recommended to leave as disabled although enabling 15M 16M can help with sound issues P2C C2P Concurrency Set to Disabled for best performance You may set this to Enabled if you want any sort of system stability System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at FOOOh FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result Video BIOS Cacheable The Setting Enabled allows caching of the video BIOS ROM at C0000h F7FFFH resulting in better video performance However if any program writes to this memory area a system error may result See 20 ET863 User s Manual DRIVERS INSTALLATION Es Frame Buffer Size The default setting of the frame buffer size is 8M AGP Aperture Size The field sets aperture size of the graphics The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any translation The default setting is 64M AGP 4X Mode The field enables or disables the AGP 4X mode of the integrated VGA function AGP Driving Control This BIOS function allows you to adjust the control of the AGP driving force It is set to Auto by default Panel Type This field sets the panel type that is supported by the system Below are the selections for the different panel types
24. er Menu Level PM Control by APM Yes Video Off Option Suspend gt Off Video Off Method V H Sync Blank Modem Use IRQ 3 Soft Off by PWRBTN Instant Off Thermal Duty Cycle 50 Wake Up Events Press Enter Phoenix AwardBIOS CMOS Setup Utility Power Management Setup Power Management User Define ITEM HELP HDd Power Down Disabled Menu Level Doze Mode Disabled Suspend Mode Disabled Phoenix AwardBIOS CMOS Setup Utility IRQ Event Activity Detect VGA OFF ITEM HELP LPT amp COM LPT COM Menu Level HDD amp FDD ON PCI Master OFF PowerOn by PCI Card Disabled Modem Ring Resume Disabled RTC Alarm Resume Disabled IRQs Activity Monitoring Press Enter SS er ET863 User s Manual 25 DRIVERS INSTALLATION Phoenix AwardBIOS CMOS Setup Utility IRQs Activity Monitoring Enabled ITEM HELP Enabled Menu Level Enabled Enabled Enabled Disabled Disabled Disabled Disabled Enabled Enabled Enabled Disabled 26 ET 863 User s Manual DRIVERS INSTALLATION ACPI Function Use this option to enable or disable the ACPI function Power Management When you press Enter while selecting this field the menu for Power Management appears The following are the fields in this menu Power Management This field allows you to select the type of power saving management modes There are four selections for Power Management Min Power Saving Minimum power management Max Power Saving Maximum power manage
25. floppy drive installed has 40 or 80 tracks 360K type has 40 tracks while 760K 1 2M and 1 44M all have 80 tracks Boot Up NumLock Status This allows you to activate the NumLock function after you power up the system Gate A20 Option This field allows you to select how Gate A20 is worked Gate A20 is a device used to address memory above MB 8s 18 ET863 User s Manual DRIVERS INSTALLATION ee Typematic Rate Setting When disabled continually holding down a key on your keyboard will generate only one instance When enabled you can set the two typematic controls listed next By default this field is set to Disabled Typematic Rate Chars Sec When the typematic rate is enabled the system registers repeated keystrokes speeds Settings are from 6 to 30 characters per second Typematic Delay Msec When the typematic rate is enabled this item allows you to set the time interval for displaying the first and second characters By default this item is set to 250msec Security Option This field allows you to limit access to the System and Setup The default value is Setup When you select System the system prompts for the User Password every time you boot up When you select Setup the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up OS Select for DRAM gt 64MB This option allows the system to access greater than 64MB of DRAM memory when used with OS 2 that depends o
26. indows restarts the new hardware wizard window will appear The wizard searches for the drivers for VIA PCI Audio Controller WDM Click Next to continue 6 In the next window select Search for the best driver for your device Recommended Click Next A oS U CUOU E OUUU MIM ET863 User s Manual 47 DRIVERS INSTALLATION 7 Now select Specify a location then key in location path as d via via686A win98 win98se assuming that D is your CDROM drive and the driver CD is in the CDROM Now click Next gt Next 8 When prompted to insert the Windows 98SE CD do so accordingly and click OK When the screen appears with a message can t find viaudio dat insert the driver CD into the CDROM and key in the file path as d via via686a win98 win98se and click Finish 9 Restart your computer when prompted for changes to take effect 48 ET863 User s Manual APPENDIX Appendix A I O Port Address Map Each peripheral device in the system is assigned a set of I O port addresses which also becomes the identity of the device The following table lists the I O port addresses used Address Device Description 000h 01Fh DMA Controller 1 020h 03Fh Interrupt Controller 1 040h O5Fh Timer 060h 06Fh Keyboard Controller 070h 07Fh Real Time Clock NMI 080h 09Fh DMA Page Register OAOh OBFh Interrupt Controller 2 OCOh ODFh DMA Controller 2
27. lay on the PCI Slot By default the PCI Slot VGA is initialized first IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive Onboard FDD Controller Select Enabled if your system has a floppy disk controller installed on the CPU card and you wish to use it If you install an add in FDC or the system has no floppy drive select Disabled in this field This option allows you to select the onboard FDD port Onboard Serial Parallel Port These fields allow you to select the onboard serial and parallel ports and their addresses The default values for these ports are Serial Port 1 3F8H IRQ4 Serial Port 2 2FSH IRQ3 Parallel Port 378H IRQ7 UART 2 Mode This item allows you to determine which Infra Red IR function of onboard I O chip The options are Standard IrDA and ASKIR Parallel Port Mode This field allows you to determine parallel port mode function SPP Standard Printer Port EPP Enhanced Parallel Port ECP Extended Capabilities Port Onboard Legacy Audio Enable or disable the on board legacy audio with this option If enabled some audio options will appear ee 24 ET863 User s Manual DRIVERS INSTALLATION Power Management Setup The Power Management Setup allows you to save energy of your system effectively Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Disabled ITEM HELP Power Management Press Ent
28. ment User Define Each of the ranges is from 1 min to 1hr Default Except for HDD Power Down which ranges from 1 min to 15 min Under this option you can also configure other features such HDD Power Down Doze Mode and Suspend Mode HDD Power Down After the selected period of drive inactivity the hard disk drive powers down while all other devices remain active Control of this mode is independent of the Power Management mode selected previously Doze Mode After the selected period of system inactivity the CPU clock runs at slower speed while all other devices still operate at full speed Suspend Mode This option decides when to shutdown video for power saving You can select it as always on or turn off video when system enters suspend mode PM Control by APM If Advanced Power Management APM is installed on your system selecting Yes gives better power savings Video Off Option This option decides when to shutdown video for power saving You can select it as always on or turn off video when system enters suspend mode ET863 User s Manual 27 DRIVERS INSTALLATION a Se Video Off Method This field defines the Video Off features There are three options V H SYNC Blank Default setting blank the screen and turn off vertical and horizontal scanning DPMS Allows the BIOS to control the video display card if it supports the DPMS feature Blank Screen This option only writes blanks to the video buffer Modem Use IRQ Thi
29. n certain BIOS calls to access memory The default setting is Non OS 2 Video BIOS Shadow This item allows you to change the Video BIOS location from ROM to RAM Video Shadow will increase the video speed C8000 CBFFF Shadow DC000 DFFFF Shadow Shadowing a ROM reduces the memory available between 640KB to 1024KB These fields determine whether or not optional ROM will be copied to RAM Small Logo EPA Show This field enables the showing of the EPA logo located at the upper right of the screen during boot up SSS 4 ET863 User s Manual 19 DRIVERS INSTALLATION SS Advanced Chipset Features This Setup menu controls the configuration of the chipset Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing By SPD Enabled ITEM HELP Memory Hole Disabled Menu Level P2C C2P Concurrency Enabled System BIOS Cacheable Disabled Video BIOS Cacheable Disabled Frame Buffer Size 8M AGP Aperture Size 64M AGP 4X Mode Enabled AGP Driving Control Auto Panel Type 07 Boot Device Select Both Power Supply Type AT OnChip USB Enabled USB Keyboard Support Disabled OnChip Sound Enabled CPU to PCI Write Buffer Enabled PCI Dynamic Bursting Enabled PCI Master 0 WS Write Enabled PCI Delay Transaction Disabled PCl 2 Access 1 Retry Enabled AGP Master 1 WS Write Disabled AGP Master 1 WS Read Disabled DRAM Timing by SPD This field enables or disables the DRAM Timing based on SPD Memory Hol
30. o 12 Date 1 to 31 Year 1994 to 2079 To set the date highlight the Date field and use the PageUp PageDown or keys to set the current time T 14 ET863 User s Manual DRIVERS INSTALLATION ee Time The time formatis Hour 00 to 23 Minute 00 to 59 Second 00 to 59 To set the time highlight the Time field and use the lt PgUp gt lt PgDn gt or keys to set the current time IDE Primary HDDs IDE Secondary HDDs The onboard PCI IDE connectors provide Primary and Secondary channels for connecting up to four IDE hard disks or other IDE devices Each channel can support up to two hard disks the first is the Master and the second is the Slave Press lt Enter gt to configure the hard disk The selections include Auto Manual and None Select Manual to define the drive information manually You will be asked to enter the following items CYLS Number of cylinders HEAD Number of read write heads PRECOMP Write precompensation LANDZ Landing zone SECTOR Number of sectors The Access Mode selections are as follows Auto Normal HD lt 528MB Large for MS DOS only LBA HD gt 528MB and supports Logical Block Addressing Drive A Drive B These fields identify the types of floppy disk drive A or drive B that has been installed in the computer The available specifications are 360KB 1 2MB 720KB 1 44MB 2 88MB 5 25in 525in 3 5in 3 5in 3 5in lt _ _ _ _
31. s field sets the IRQ used by the Modem By default the setting is 3 Soft Off by PWRBTN This field defines the power off mode when using an ATX power supply The Instant Off mode allows powering off immediately upon pressing the power button In the Delay 4 Sec mode the system powers off when the power button is pressed for more than four seconds or enters the suspend mode when pressed for less than 4 seconds The default value is Instant Off Thermal Duty Cycle This field enables or disables the thermal duty cycle The default setting is 50 Wake Up Events The HDD FDD COM LPT Ports and PCI PIRQ are I O events which can prevent the system from entering a power saving mode or can awaken the system from such a mode When an I O device wants to gain the attention of the operating system it signals this by causing an IRQ to occur When the operating system is ready to respond to the request it interrupts itself and performs the service eee 28 ET863 User s Manual DRIVERS INSTALLATION ee PNP PCI Configurations This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations PNP OS Installed No ITEM HELP Reset Configuration Data Disabled Menu Level Default is Disabled Select Enabled to reset Extended Resources Controlled By Manual IRQ Resources Press Enter DMA Resources
32. sebo ceegram instal the boo divors Pos dont lo entab them you can uncheck fr arsoculad check bar i MA ATAR Vardai Suc rivet FF ARQ outing hn por Oresi MA INF Driver 1 408 sim e ts AAA AAA ee 36 ET863 User s Manual DRIVERS INSTALLATION 7 Click Next to install the VIA ATAPI Vendor Support Driver ATAPI Vendor Suppoet Unver 1 20 E S o SSS ET863 User s Manual 37 DRIVERS INSTALLATION 9 Click Next to install the VIA AGP VxD in Turbo mode VIA GART AGP Dower 415 E Setup ragam e lasta lira AGP dive tor yore O Inctal VIA AGP YD in Standard modo cuca 10 Click Finish to restart the computer and for changes to take effect Setup hee ried copra ties In pour comptes Belts yo Cat te Ihe pogam pou Mee esata oF yout compu ker C Mo yal restart mp can puras eter Remove any doka ton thay dese and than ches Fired to complete lun 38 ET863 User s Manual DRIVERS INSTALLATION VGA Drivers Installation After installing the VIA 4 in 1 drivers you may now install the VIA 8606 VGA Driver Follow the steps below to proceed with the installation NOTE Before installing the VGA drivers on Windows NT 4 0 you need to install Service Pack 3 or above 1 In your Windows operating system click Start gt Settings gt Control Panel gt Display gt Settings gt Advanced 2 Click the Adapter tab then click on the Change icon Standard PCI Graphics Adapter VGA Properties 29 x
33. ser s Manual 11 DRIVERS INSTALLATION A e _z gt P E EA BIOS Introduction The Award BIOS Basic Input Output System installed in your computer system s ROM supports Intel Pentium II III processors The BIOS provides critical low level support for a standard device such as disk drives serial ports and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system BIOS Setup The Award BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup utility When you turn on the computer the Award BIOS is immediately activated Pressing the lt Del gt key immediately allows you to enter the Setup utility If you are a little bit late pressing the lt Del gt key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reset button or simultaneously pressing the lt Ctrl gt lt Alt gt and lt Delete gt keys You can also restart by turning the system Off and back On again The following message will appear on the screen Press lt DEL gt to Enter Setup In general you press the arrow keys to highlight items lt Enter gt to select the lt PgUp gt and lt PgDn gt keys to change entries lt F1 gt for help and lt Esc gt to quit
34. some cases ET863 User s Manual 13 DRIVERS INSTALLATION A _ _ JQRQRQQEPIEAXAX2_O _A A Standard CMOS Setup Standard CMOS Setup choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling If the board is already installed in a working system you will not need to select this option You will need to run the Standard CMOS option however if you change your system hardware configurations the onboard battery fails or the configuration stored in the CMOS memory was lost or damaged Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Tue Mar 26 2000 ltem Help Time hh mm ss 00 00 00 Menu Level IDE Primary Master None Change the day month IDE Primary Slave None Year and century IDE Secondary Master None IDE Secondary Slave None Drive A 1 44M 3 5 in Drive B None Video EGA VGA Halt On All But Keyboard Base Memory 640K Extended Memory 129024K Total Memory 130048K At the bottom of the menu are the control keys for use on this menu If you need any help in each item field you can press the lt F1 gt key It will display the relevant information to help you The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following describes each item of this menu Date The date format is Day Sun to Sat Month 1t
35. st PCI Slot DE HDD Block Mode Enabled Onboard FDD Controller Enabled Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 Onboard Parallel Port 378 IRQ7 UART 2 Mode Standard Onboard Parallel Mode Normal Onboard Legacy Audio Disabled OnChip IDE Channel 0 1 The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately IDE Prefetch Mode This field enables disables the prefetch buffers in the PCI IDE controller The prefetch buffers are used as a temporary storage place as data is transferred from one location to another IDE Primary Secondary Master Slave PIO These fields allow your system hard disk controller to work faster Rather than have the BIOS issue a series of commands that transfer to or from the disk drive PIO Programmed Input Output allows the BIOS to communicate with the controller and CPU directly The system supports five modes numbered from 0 default to 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode L a M a MM ET863 User s Manual 23 DRIVERS INSTALLATION Sr IDE Primary Secondary Master Slave UDMA These fields allow your system to improve disk I O throughput to 33Mb sec with the Ultra DMA 33 feature The options are Auto and Disabled Init Display First This field allows the system to initialize first the VGA card on chip or the disp
36. ual DRIVERS INSTALLATION SEE 4 Select Specify a location and specify the path of the drivers Assuming that the drivers are in diskettes the path would be A RTL8139C Win98 But if your drivers come in a CD disc the path would be assuming d is your CDROM drive d LAN RTL8139X WIN98 After entering the path click Next Click Next to start the driver search Mindeord search fis ren deers br tz eves dalobsss mpenected devo in an ol tha Resor Hed Dm stan fie souch TF Etoo dde dry T Padre FR eee tee eet Sgecty ajocadar 5 When the driver location has been verified click Next to start the driver installation ido ri yer fle speach los ther das Reade AFLINN IN PO Es Diksi NIC Aledo mis nave iced kors testis best diver for ta Grice Ach Bekta select a dieron daei c dich New Lucston of wer a unr aso TREN de EY orm 6 After file copying is done click Finish and restart the computer when prompted System Settings Change Q To fan seling ub pour new hadise pou huit teat yoni Conde Do poo want bo teeta ina cono des now E w ET863 User s Manual 45 DRIVERS INSTALLATION Audio Drivers Installation Follow the This chapter describes the VIA 686A B audio driver installation process for Windows 98SE and Windows NT Follow the installation steps below to finish the audio driver installation Windows 98SE Audio Driver Installation Insert the driver C
37. ver database on your hard drive and in any of the following selected locations Click Next to start the search T Floppy disk drives IT CD ROM drive FF Microsoft Windows Update IV Specify a location fE AVIASVIASBOBS Wing X lt Back Next gt Cancel 6 When Windows find the driver click Next for Windows to install the drivers into the system Update Device Driver Wizard Windows driver file search for the device 53 Graphics Twister Windows is now ready to install the best driver for this device Click Back to select a different driver or click Next to continue Location of driver RQ ewinsnscos wnaasrwesaz3 ne 7 When the driver installation is finished click Finish for changes to take effect ET863 User s Manual 41 DRIVERS INSTALLATION LAN Drivers Installation This section describes LAN features and driver installation of the onboard Realtek RTL8139C Ethernet controller Introduction Realtek RTL8139C is a 32 bit 10 100MBps Ethernet controller for PCI local bus compliant PCs It supports bus mastering architecture and auto negotiation feature which make it possible to combine one common type of Ethernet cabling an RJ 45 connector for twisted pair cabling that can be used for both 10Mbps and 100Mbps connection Extensive driver support for commonly used network operating systems is also provided Features Conforms to the Ethernet IEEE 802 3u standard
Download Pdf Manuals
Related Search