406 User`s Manual
Contents
1. Connect the AC Power cord and make sure that the line is completely connected between the instrument and power outlet Check the power switch is turned on Please refer to 3 1 Power on off and Door Release If the door is not closed completely the instrument can t run Check the Door LED on the display window and close the door completely If the power is out check the main fuse for the laboratory to supply the power If it is not solved in shortly open the door with the Emergency Door Tool manually for safety of sample Please refer to 4 6 Emergency Door Open Remove the dirt at the door latch and then close the door completely again If the door seems not being closed by mechanical reason please contact our service team Please check the balanced status of both the table and the instrument Please re check the coupling status of the following three matches to minimize the noise 1 the balanced way of coupling of the rotor into the motor shaft 2 the completeness of fixing of the Rotor Locking Nut on the rotor 3 the matching status of Rotor Lid with the rotor Please refer to 3 2 Rotor coupling and disassembling Check balances of samples in the rotor Please refer to 3 3 Positioning of Sample Tubes and load the same weight of samples symmetrically A 17 35Y LIZEN Low Speed Centrifuge 406 If the instrument shows the error code with beeping sound press STOP button to stop the beeping sound and press2. Use the emergency door open function only when the door button on the control panel is dumb under the condition of complete stop of rotor running Never try to open or move the instrument if it is not completely stopped If the power input is more than 10 of the recommended voltage or fluctuates frequently it may cause malfunction of the instrument and often result serious damage Install the instrument at the place without any kinds of corrosive gases 2 Product Description amp Technical Specifications 2 1 Product Description Door A Power Chamber Socket qaum GE 1 Emergency Door dde B Power Open Hole Switch Control Panel beai 8 35Y LIZEN Low Speed Centrifuge 406 Accessory User manual Power Cable Rotor Locking Tool Emergency Door Open Tool Cat no GZ 406 includes GRA 12 6 2 2 Technical Specifications GO 9 35Y LIZEN Low Speed Centrifuge 406 3 Installation 3 1 Power On Off and Door Release 3 1 1 Power On off Action 1 Connect the AC Power cord at the power socket on the right back of the instrument 2 Turn on the instrument by pressing a switch on the right side of the instrument 3 Press the Door button to open the door 3 1 2 Door Release Action 1 For opening the door press the DOOR button The door is automatically opened after completion spinning with beeping sound Close the door until he
3. I any rust appears clean it with neutral detergents and keep dry 5 2 Chamber 1 Keep dry inside the chamber after every use 2 If the chamber is contaminated dip the cloth in neutral detergent and clean contaminated area 5 3 Shaft 1 Always make special attention to clean the motor shaft to avoid any imbalance problem due to the contaminants 2 After using the instrument take out the rotor from the shaft and clean the shaft with dry soft cloth to keep dry 5 4 Rotor 1 If any parts are contaminated with samples clean the rotor with soft wet cloth and keep the rotor dry 2 Be careful not to make scratches inside or on the surface of rotors Any small scratches can cause corrosion of the rotor and big damage to the instrument 3 If you do not use the instrument keep the rotor separately from the motor shaft and stand it upside down 5 5 Transportation of the instrument 1 If you need to move or ship the instrument be cautious to protect the motor shaft from any physical impact or turbulence 2 Do not mount a rotor in any cases of movement Fill inside the chamber with proper materials to keep the motor shaft on place and not to be influenced by physical pressure 6 Trouble Shooting A 16 BER d LIZEN Low Speed Centrifuge 406 6 1 Check list Symptom Power failure Can t be started Can t open the door Can t close the door Noise and vibration during running 6 2 Error Code Check list
4. change input value gt After keeping holding finger on the A V buttons for 5 seconds the unit of setting value is changed to 100 rpm from 10rpm 3 Press the RPM RCF button again for saving 4 2 2 Setting RCF gt Speed setting unit 1 rcf or 10 rcf 1 Press the RPM RCF button twice RCF MODE is generated by pressing a RPM RCF button twice 2 Press the A V buttons to change input value After keeping holding finger on the A W buttons for 5 seconds the unit of setting value is changed to 10 rcf from 1 rcf 3 Press the RPM RCF button again for saving 4 3 Setting Time gt Speed setting unit 1min or 10min 1 sec or 10 sec Action 4 3 1 Setting MIN 1 Press the TIME button once Minutes MODE is generated with pressing a TIME button once 2 Press the A V buttons to change input value After keeping holding finger on the A W buttons for 5 seconds the unit of setting value is changed to 10min from 1 min 3 Press the TIME button again for saving 4 3 2 Setting SEC 1 Press the TIME button twice Seconds MODE is generated with pressing a TIME button twice 2 Press the A V buttons to change input value After keeping holding finger on the A W buttons for 5 seconds the unit of setting value is A 13 BER d LIZEN Low Speed Centrifuge 406 changed to 10 sec from 1 sec 3 Press the TIME button again for
5. saving 4 4 Start Stop Action 1 After setting RPM RCF and Time press START STOP button gt During running a Start LED is turned on In case of pressing the START STOP button during running the running is stopped 4 5 Program Saving amp Recalling Action 4 5 1 Program Saving l Set parameters Refer to 4 2 4 3 2 Press the PROG button longer than 3 seconds to save your preferred set values The LED of PROG button and SEC Save is turned on 3 Input the program number by using A V button Save up to 10 programs 4 Press the PROG button again to complete the saving The setting value is saved gt If you do not press the PROG buttons for 5 second the setting mode is cleared 4 5 2 Program Recalling 1 To recall the saved program just press the PROG button shortly The LED of PROG and MIN Call is turned on 2 Check the program number to call and enter the program number you want to recall by pressing A V button 3 Press PROG button once again The setting values are displayed according to your saved number gt If you do not press the PROG buttons for 5 second the setting mode is cleared A 14 BER d LIZEN Low Speed Centrifuge 406 4 6 Emergency Door Open For emergency door opening you can use the Emergency Door Open Tool as long as the instrument is completely stopped The door can be unlocked manually with Em
6. EO display with bright white lettering on a blue LCD background B Automatic HERT conversion for prompt detection of g force B Easy ta check actual rpm through the top window of door E Program memory for up to 10 programs E Soft spin key for for gentle acceleration and deceleration B Actomatic door opeing function when rotor is statics for easy retrivel of samples B A large assortment of rotors ced angie ar swing out with buckets and adaptors EASY CUSTOMIZATION g Any rotors sample containers and adaptors can be manufactured according to tustomer s specification B Flexibility of including any additional functions or programs in need ECO FRIENDLY MANUFACTURING B Dust free AL induction motor WB Very quiet operation at lesser than 6 d8 mM 3 35Y LL E N Low Speed Centrifuge 406 1 1 1 2 2al 2 2 esk 3 2 3 3 4 1 4 2 4 3 4 4 4 5 4 6 4 7 FL Dre 373 353 CONTENTS Page Meanings of A PreCaUTIOTS ke 6 Mu ge Eau deie EO 6 belli aaa 6 Product Description amp Technical Specifications a 8 Product Description a 8 Technical Specification 9 Installation ii eee 10 uev Weed iii 10 Rotor coupling and disassembling a 11 FSI ON NUN Or SSmple NN Screen 11 ERT RRE 12 By EAN EONS NUE ei E aa EA 12 GOR ARE re 12 Setting TIME 13 GE E 14 Program Saving amp Recalling a 14 EMCIGENC RAE 15 FUSE replacement 15 KLELET EN E E 16 Outer part or
7. Enter button to release of the error status and make the instrument go to the default setting again Error Error 1 Or Error 9 Error 2 Error 3 Error 4 Error5 Error 6 Possible Causes RPM Sensor Door Motor Overheating Low Voltage High Voltage Over Speed Actions Shut off the power supply and then turn on the power switch again to check the instrument If the error code shows continuously although you try to operate again please call Gyrozen Field Service Engineer If the door is not closed completely this message is appeared Remove the dirt at the door latch and then close the door completely again Check the Door LED on the display window If it is not solved in shortly open the door with emergency door tool manually for safety of sample Please refer to 4 6 Emergency Door Open If the motor is overheated this message is appeared Shut off the power supply for an hour and then turn on the power switch for checking the instrument If the error code shows continuously please call Gyrozen Field Service Engineer If the power input of Power supply V Hz is 10 less than required power this message is appeared Shut off the power supply and then check the voltage of the Power supply V Hz Use AVR to provide proper power If the power input of Power supply V Hz is 10 more than required power this message is appeared Shut off the power supply and then check th
8. Low Speed Centrifuge 406 User s Manual Gyrozen Co Ltd B station 30 12 Gyeryong ro 141 gil Yuseong gu Daejeon 305 301 Korea Tel 82 42 719 8200 Fax 82 42 826 9848 WWW gyrozen com DOC No C00DC00204 11 La yr RUZEN Designed to suit your exact needs Wide range of modern centrifuges for a wide variety of laboratory applications THE BEST FUNCTIONAL QUALITY lo NE A SAFETY and ROBUSTNESS Manufactured and tested to IEC standards stable spinning operation within 2 variation Steady and soft deceleration with dynamic brake technology Automatic recognition and alarms for imbalance over speed and over heat m Automatic RPM RCF conversion Safety door lock mechanism ensures the door is locked whilst in operation mode Unique door drop protection protects the operator and samples when loading and unloading Automatic detection and alarms for imbalance excess speed and heating Automatic door open scheme with safety level of aperture depth not to damage operators m Emergency door lock release helps to open the instrument when power blackout or The Aerosol tight buckets and rotors prevent contamination and ensures safety Autoclavable and corrosion resistant rotors ensure safety and long life High quality cabinets with scratch resistant powder coated finish A 2 BER d LIZEN Low Speed Centrifuge 406 CONVENIENCE IN OPERATION d Infutve cotra pannel with asy to ust BB Easy to need L
9. aring clank shut When the door is opened the door LED turns on The door is not opened while the instrument is running If the door is opened the instrument could not be operated even with pressing the Start button Power Failure If there is any power failure during operation door is not opened with Door button Door can be opened only when the operation is completely stopped and the power is on again If you want to open the door at the power failure please refer to 4 6 Emergency Door Open A 10 BER d LIZEN Low Speed Centrifuge 406 3 2 Rotor coupling and disassembling Action 1 Before coupling a rotor clean the motor shaft and chamber with soft dry towel l 2 Mount a proper rotor into the motor shaft Put the Washa at the center hole of the rotor and assemble it with Door Locking Nut e d To assemble the rotor Rotate the Door Locking Nut clockwise until tightly assembled To disassemble the rotor Rotate the Door Locking Nut counterclockwise 3 Load the 15ml stainless steel sleeves at every hole 3 3 Positioning of Sample Tubes Before loading sample tubes check the water drop or dirt in the rotor hole or inner adaptor 1 gt I there is a water drop or dirt in the rotor hole or inner adaptor remove it with soft dry cloth 2 Tubes should be placed in the rotor with same amount of samples at symmetrical positions Only use appropriate centrifugal tubes and do not
10. d not exceed the rated speed or specific gravity Samples whose density is greater than 1 2g ml must have reduced maximum rotational speed to avoid rotor failure The sample content should not exceed 8096 of total capacity of a tube Otherwise it would cause spillage of sample fluid and even the tube breakage ALWAYS load the tubes symmetrically with evenly weighted samples to avoid rotor imbalance If necessary use the water blank to counterbalance the unpaired sample The operation speed should not exceed the highest value of the individual guaranteed g forces of each centrifuge rotor bucket or adaptors and sample container especially the guaranteed g force of sample container should not be neglected The rotors should be cleaned and kept dry after every use for longer life and safety ALWAYS disconnect the power supply prior to maintenance care and service to avoid electrical shock ALWAYS use proven disinfection procedures after centrifuging biohazardous materials Should not centrifuge flammable toxic radioactive explosive or corrosive materials 7 arr LIZEN Low Speed Centrifuge 406 18 When it is necessary to use toxic or radioactive materials or pathogenic micro organisms which belong to the Risk Group II of WHO Laboratory Bio safety Manual should follow national regulations Do not place dangerous materials within 30 cm distance around the instrument and that is also recommended by IEC 61010 2 020
11. e voltage of the Power supply V Hz Use AVR to provide proper power If the instrument is spun with over speed there will be some problems A 18 BER d LIZEN Low Speed Centrifuge 406 in the overload of motor and the output of motor Shut off the power supply and then turn on the power switch again to check the instrument If the installed software has bugs this message is appeared Error 7 Software l l Tuning the firmware Download Check weight balances of samples Please refer to 3 3 Positioning of Error 8 Imbalance i Sample Tubes and then turn off and on the instrument for checking Any wire disconnection or tuning of the instrument must be performed only by a service engineer who is authorized by GYROZEN Co Ltd 7 Rotors and Accessories Angle Rotor GRA 15 6 Led Tube hee apatiet 0 1S eden c e C Marra Noce More Now Mostra Sheet 15 74 Somn MELIA tab Ma reame Try barrun MaswieriDu me 13x63 o B Ia Letek Rad is pam 5 vt iti 115 116 1 Pan OP 4 000 Man ETE AK PART 2S Man ET s Farc LE 1282 ET ZA 2075 2 00 19 L3 Y Ele Elba Low Speed Centrifuge 406 8 Product Range CC amp 20 L Y LJ Va E N Low Speed Centrifuge 406 Doc No STC A08 113 KELO8 C10032 EC Declaration of Conformity We Gyrozen Co Ltd B Station 544 1 Bongmyeong dong Yuseong gu Daejeon 305 301 Korea declare under our sole responsibility that the product Descr
12. ergency Door Open Tool through the emergency opening hole 1 Find the emergency hole at the left side of the instrument 2 Insert the Emergency Door Open Tool into the hole and push it until the door is released Manual opening should be performed only when spinning is completely stopped Otherwise harmful damage will be accompanied to not only operators but samples After opening the door manually it is recommended to wait until normal electricity comes back 4 7 Fuse replacement When the power is not turned on please check the connection of power consent power switch Replace the fuse as following instruction if the power is still not turned on Action l Separate the AC Power Cord at the back of the instrument and push the flat head screwdriver for bring out the fuse case Spare Fuse v Connacted Fuse in the power 2 Replace the damaged fuse with new one from the fuse case and then connect in the power 5 Maintenance 15 35Y LIZEN Low Speed Centrifuge 406 5 1 Outer part of instrument 1 Clean the outside of the instrument with dry soft cloth If necessary dip the cloth in neutral detergent and clean contaminated area Keep completely dry after cleaning 2 Do not use any volatile chemicals such as alcohol and benzene etc 3 Be careful not to make scratches on the surface of the instrument The scratches can cause corrosion on the surface of the instrument v
13. exceed the speed beyond the tube s max g force gt For safety fill the sample for 70 8096 in the tubes Correct Way of Sample Balancing amp Tube Usage ai 9 000 xg 8 000 xg e URIEN i I 000 xg 10 8096 filling for safety E Check the g force of BEE If the number of samples is not in pair please load the control tubes at each symmetrical position Otherwise it results noise and vibration which eventually damage the instrument For safety the Imbalance Cut Off function will be occurred if there is imbalance of loading tubes IS Error 8 Imbalance error Please refer to 6 Trouble Shooting 11 L3 Y Ele Elba Low Speed Centrifuge 406 4 Operation 4 1 Key Functions of Control Panel TEEI TTU ET Mica OLD IDA 00 0lo SEC Save START STOP Use to start or stop operation PROG Use to save a set of setting values or recall the saved program number Door Use to open the instrument lid RPM RCF For automatic conversion of RPM RCF and to set the speed TIME Use to set time available range up to 99 min 00 continuous 4 2 Setting RPM RCF gt Maximum RPM RCF 4 000 RPM 2 700 x g Action 4 2 1 Setting RPM gt Speed setting unit 10rpm or 100rpm 1 Press the RPM RCF button once gt RPM MODE is generated by pressing a RPM RCF button once A 12 35Y LIZEN Low Speed Centrifuge 406 2 Press the A V buttons to
14. iption of Equipment Centrifuge Model Name 416 to which this declaration relates is in conformity with the following standards or other normative oratory use Part 1 General Safety requirements for electrical r measurement control and laboratory use Part 2 Particular requiremen Electrical equipment for measurem EMC requirements Industrial scientific and medical ISM disturbance characteristics Limits a 2004 108 EC the European Parliament and of Council of 15 December 2004 on the approximation of the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89 336 EEC 2006 95 EC Directive 2006 95 EC of the European Parliament and of the Council of 12 December 2006 on the harmonization of the laws of Member States relating to electrical equipment designed for use within certain voltage limits Issued date November 11 2008 Confirmed by f c Sun Ki Kim President YEA 21 3 LIZEN Low Speed Centrifuge 406
15. jury or physical damage on the instrument or its accessories 1 ALWAYS locate the instrument on a flat rigid and stable table capable of withstanding the weight of the instrument and its spinning operation beai 6 35Y LIZEN Low Speed Centrifuge 406 10 LL 12 Lo 14 15 16 17 ALWAYS make a safety zone of 30 cm around the centrifuge to indicate that neither hazardous materials nor persons should be permitted within the area during operation v ALWAYS position the instrument with enough space on each side of instrument to ensure proper air circulation ALWAYS install the instrument within a temperature and humidity controlled environment Permissible ambient temperature 5 C 35 C Relative humidity lt 85 Before connecting the power check the rated voltage Should not use unapproved rotors and accessories v Only use rotors from Gyrozen Co Ltd with appropriate centrifugal tubes and suitable adaptors to embrace sample containers tightly enough inside rotors Before operating the instrument check if the rotor and the rotor lid are securely fastened v Should operate the instrument with a rotor properly installed and secured to the motor shaft Mount the rotor on the motor shaft properly check it with spinning manually Do not stop the rotor by touching with hand during the instrument is running Emergency door open should be performed only when spinning is completely stopped Shoul
16. qs A 16 Chamber SM 16 EN M O 16 Rotor EMEN 16 Trdnspoptat HF ted SU HIFTTGTIE E 16 4 35Y LIZEN Low Speed Centrifuge 406 6 liceo za elei elea 17 6 1 81 4 E EO 17 6 2 ErrOr COC 18 7 Rotors amp Accessories a 19 8 FIOCIUGE riez 20 9 CR 21 beai 5 35Y LIZEN Low Speed Centrifuge 406 1 Meanings of Symbols amp Safety Precautions 1 1 Meanings of Symbols 1 1 1 Symbols on the device Symbol Meaning Symbol Meaning Attention and warning Attention and warning for electric shock 1 4 Please be careful i r y na a not to get hands caught CAUTION BUE Rotors ela Door gi HRU Attention and warning aga 234 pane ons Attention and warning uou FA 42 Nk l for door opening and for rotor coupling in the instrument closing Attention and warning l Indicate a hole for for correct way of BO manual door opening in sample balancing in the case of emergency rotor 1 1 2 Symbols in this document This symbol refers to safety Note relevant warnings and indicates This symbol refers to the important possible dangerous outcomes reminder 1 2 Safety Precautions Before using the instrument please read this operation manual to ensure correct usage through understanding Incorrect handling of the instrument could possibly result in personal in
Download Pdf Manuals
Related Search