MPEG Series Manual - Artefects by Virtualtronica
Contents
1. Intruder Alarm System Key Model EE E E E W E E E E E E W E E W W E W E E W W W E E E E E W E W W E W E W E W W E W W I W E W I W W E E E E E Statement This equipment must be installed and used in strict accordance with the instructions given in this user documentation Virtualtronica cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice Should you require any technical assistance please contact directly with Virtualtronica or use the site http www artefects pt Notice e Keep the device away from high temperature places heat source and direct sunlight e Keep away from water If it gets wet cut off the power immediately e The reference range for operation humidity is below 80 RH e The reference range for operation temperature is between 10 C and 50 C e If the equipment is not working properly please contact Virtualtronica do not try to disassemble or modify the equipment in any way e Check carefully the voltage of the power adaptor don t insert incorrect power otherwise it will damage the device and is not covered by warranty Technical e Working power AC 100 230V DC 12V 1A e Static current lt 35mA when not charging Alarm current lt 120mA e Built in Li lon battery 3 7V 800mAH rechargeable Standby around 24 hours Full charging time 8hours e Receiving and e2. long sound which means the record is successful 6 11 Play audio tape 9 Raise the fixed line telephone connected with the main engine and then you can listen to the recording contents Press any button it will quit the play 11 http www artefects pt e AATEFECTS 7 Included Accessories Technical Specifications 7 1 Wireless Remote Control e Battery Type 27A 12V alkaline battery e Emitting distance 100m in open area h 7 2 Wireless intelligent Door Sensor e Battery Type 23A 12V alkaline battery Emitting distance 100m in open area e Magnetic alarm Distance lt 4cm ALARM LED LOW VOLTAGE LED LESS THAN 1CM a Door open sensor installation Distance less than CM 7 2 1 Door Sensor installation Use the random equipped double side tape to stick a magnetic stripe on the door and affix the gate magnetic emission box on the doorframe Pay attention to put the magnetic strip close to the side with indicator lights of the emission box during installation assuring proper alignment and the smaller distance the better 7 3 Wireless wide angle PIR Sensor e Battery Type 9V alkaline battery e Emitting distance 100m in open area Detecting distance 50 5to9m 12 http www artefects pt el MATEFECTS 40 degree Wireless PIR motion sensor 50 degree _ Surveillance Area 2 1m SS 7 3 1 DIR Sensor installation The principle of infrared detectors is to sense people s mov
3. by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits Ce CE Rules European regulations This digital equipmenttulfilss the requirement for radiated emission according to limit B of EN55022 1998 and the requirement for immunity according to EN50082 1 1992 Liability Virtualtronica Lda cannot be held responsible for any technical or typographical errors and reserves the right to make changes to the product and manuals without prior notice Virtualtronica Lda makes no warranty of any kind regard the material contained within this document including but not limited to the implied warranties of merchantability and fitness for any particular purpose 14
4. outside line into LINE2 of the main engine and connect LINE1 of the main engine with telephone using attached telephone wire of alarm Then joint up the power source and warning signal meanwhile the main engine will give a sound of B and light of the power source goes on which means the main engine starts working http www artefects pt el AATEFECTS 3 Basic Functions 3 1 Set up defences Press AN button on remote controller or ARMING button on panel and the main engine will give a sound of B then the main engine enter the defence situation or delayed defence state 3 2 Cancel defences Press m button on remote controller or DISARMING button on panel and the main engine will give two sounds of B then the indicator lamp dies out so the main engine is in a state of no defences 3 3 Emergency alarm Press MB button on remote controller or ALARM button on panel main engine will enter the state of emergency alarm instantly calling automatically and siren going off Press gt button on remote controller once is silent alarm while long press or two presses will open the siren 3 4 Intelligent defences Press 5 button on remote controller or INTELLIGENT button on panel then main engine will enter the state of intelligent defence or delayed defence 4 Status indication of main engine digital tube The main panel will indicate the status of the alarm with this codes
5. phone is in use or not able to connect the system will dial next alarm phone until it is dialled and hosts confirm It will play records after receiving alarm phone and the operation methods are similar to remote setup http www artefects pt el MATEFECTS 6 Function settings All the settings can be carried out under the undefended situation with a long ring for all the proper operations while two short sounds for wrong settings 6 1 Warnings Silent alarm 0 0 no alarm whistle for warning Vocal alarm 0 1 alarm whistles for warning 6 2 Open and Close password protection To open password protection please press 1 1 if you hear a di sound which means set successfully After hearing di sound please wait about 26 seconds The system will start password protection automatically So if nobody can arm or disarm on the panel if no input password After finishing if you want to disarm or arm on the panel you need to press password you set For example if i set the password is 1234 we need to press 1234 to enter into the system and then arm or disarm Otherwise you can t control on the panel To close password protection Please press 1 0 6 3 Set up common alarm telephone numbers 1 5 2 2 4 Set 1 5 groups telephone number 1 5 is the ordinal of the telephone number 7 stands for telephone numbers 6 4 Set up emergency phone numbers 6 The same method as above press alar
6. TIMES 6 6 24 RECOVER FACTORY SETTINGS 8 PASSWORD 6 25 SETUP ALARM VOICE RECORD O PASSWORD 6 26 PLAY AUDIO TAPE 9 7 INCLUDED ACCESSORIES TECHNICAL SPECIFICATIONS sss nn nn ssssnon fole WIRELESS REMOTE CONTRO E caia ta fios WIRELESS INTELLIGENT DOOR SENSOR ias 7 2 42 DOOR Sensor installation iii A Ai A A 12 7 3 WIRELESS WIDE ANGLE PIR GENSOn EEN O A 7 3 1 PIR Sensor installation 2 1 ccccccccccconecseescenececescenecersecersersessersessesses fin QQ 13 http www artefects pt el AATEFECTS 1 PRODUCT INTRODUCTION 1 1 Product summary Thank you for choosing our company s Intruder Alarm System This alarm system combines a complete kit for intrusion alarm with a Central Unit a magnetic sensor a motion sensor PIR 2 remote controls and a power supply It is very suitable and affordable for houses garages shops small to medium office building and several other uses You can also use other accessories like gas flood smoke fire sensors or internal and external sirens panic buttons and external keypads with this central unit For more information regarding other accessories please go to www artefects pt 1 2 Features e Keypad and Blue LED display e 5 phone numbers to call on alarm e 1 phone number to call on emergency e Settings for Arm Delay Alarm Delay Administrator Password e Crack proof function None wireless remote controller can cancel defenc
7. able when hosts at home because indoor infrared alarm function is cancelled while the gate magnetisms on the door and window are still in a state of monitoring e Emergency defence area 3 No matter under the defended or undefended situations once triggered it will report to the phone number immediately This is suitable for gas reaction smoke reaction safe emergency accesses and other special occasions e Multi checked defence area 4 Under the situation of defence or intelligent defence if two or more detectors that set up multi checked are all triggered within 30 seconds the main engine will give an alarm Therefore based on this pattern none of the infrared detectors will misinform the events Note Para funcionar neste modo deve criar 2 ou mais zonas e configurar todas neste modo http www artefects pt el MATEFECTS e Delay alarm defence area 5 Este modo serve para atrasar o alarme depois da activa o do sensor Exemplo Ao abrir a porta necessita de 10 segundos para chegar a central e desactivar a central Este modo ideal para o sensor magn tico da porta de entrada e Delete defence area 6 Significa e means delete selected defence areas only for wireless defence areas Note when you input 8 99 6 all of the wireless defence areas will be deleted e Repeat triggered defence areas 7 When the detector is triggered once the system will not alarm immediately Only when it is triggered again wi
8. e SP for defence e CF for no defence e 99 for emergency alarm e DE for intelligent defence e Fi for alarm when telephone lines disconnect e F3 means there is no learning defence area 1 98 means wireless defence area L1 L8 means wired defence area http www artefects pt el MATEFECTS 5 Distance Remote operation methods 5 1 Calling to the central You can use any telephone to dial the numbers of main engine and it will put on automatically after system detecting the ring times you have been setup When you hear the beep input passwords two sounds when the password is wrong while when the wrong time is above 3 the phone will hang up automatically and if it is correct you can have remote control of the system Please press after accomplish all operations then you can implement other operations and hang up telephone e Press 1 to monitor the scene e Press 2 to start siren e Press 3 to stop siren e Press 4 to set up defences e Press 5 to cancel defences e Press 6 to play recorded voice e Press to confirm and hang up If the password is wrong or no operations within 20 seconds it will hang up automatically Press 1 button once you can listen for 20 seconds 5 2 Processing method after receiving alarm In case of emergency main machine will dial the setup telephone numbers automatically and give alarm rings based on settings If the host s
9. eccccececececcccccececuccccececscueueauaesececauacaesetseeraeaens 7 6 FUNCTION SETTINGS e LM onan cn cnccccncnensnccccncnensnsnncnenenensnscnensnscsesenenenenensnsenenensnseseneness 8 Giles WARNNG ET EE EE EE 8 6 2 OPEN AND CLOSE PASSWORD PROTECTION 8 6 3 SET UP COMMON ALARM TELEPHONE NUMBERS Silb MB eeeerana aan eeranaaanenaa 8 6 4 SETUP EMERGENCY PHONE NUMBERS Gd 2 8 6 5 DELETE TELRRMONE NUMBERS TA be E EE 8 6 67 ALARMA E e a E o 8 6 7 ALARM RINGING TIME OI 9 6 8 INQUIRY ALARM DEFENCE AREA DO 9 6 9 THE STATE OF SETTING UP DEFENCE AREA 8 ODE renan career 9 GO DEFENSE AREAS ell aci E 9 6 11 INPUT PASSWORD PASSWORD rara errante 10 6 12 LEARNING REMOTE CONTROLLER DEE 10 6 13 LEARNING DETECTOR 0 EE ERROR BOOKMARK NOT DEFINED 6 14 DESIGNATED SERIAL LEARNING DETECTOR 8 T an rnranr ar annnnrnr annue 10 6 15 DELETE ALL OF THE REMOTE CONTROLLERS IO 10 6 16 DELETE ALL OF THE DEFENSE AREA DETECTORS 8 99 6 rara 11 6 17 USE REMOTE CONTROLLER TO OPEN AND CLOSE THE SIREN SOUND 210 11 6 18 OPEN CRACK PDROOEEUNCTIONTZ2IT ERROR BOOKMARK NOT DEFINED 6 19 CLOSE CRACK PROOF FUNCTION 30 ERROR BOOKMARK NOT DEFINED 2 http www artefects pt ww AATEFECTS 6 20 DELAYED TIME OF SETTING UP DEFENSE INPUTTING AN 6 21 OPEN THE ALARM FUNCTION WHEN TELEPHONE LINES DISCONNECT BI 6 22 CLOSE THE ALARM FUNCTION WHEN TELEPHONE LINES DISCONNECT 5 O 6 23 REMOTE SETUP TELEPHONE RINGING
10. ement through sensing infrared signals generated by bodies and the detection range is usually 5 9 meters Infrared sensor should be installed about 2 1 meters away from ground Aim straight at the detection ranges Moreover the infrared detector can be only installed in the room without facing the sunshine windows and other places where temperature is easy to change because the installed location may influence the detection range and accuracy FE FCC Rules Electromagnetic Compatibility EMC This device compiles with FCC Rules Part 15 Operation is subject to the following two conditions e This device may not cause harmful interference e This device must accept any interference received including interference that may cause 13 http www artefects pt ww AATEFECTS undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a partial installation If this equipment does cause harmful interference to radio or television reception which can be determined
11. es e Alarm on Landline disconnection e 99 wireless zones Every zone with types of defence e 7 types of defence areas Bypass Common Intelligent Emergency Multi check Delayed Repeat Triggered e Alarm Information Mode PSTN Call e Learning codes for remote controls and sensors e Support Arming disarming and monitor voice by calling to the alarm unit e Arm disarm by Remote control Main keypad Voice call or optional wireless keypad 1 3 Included in the box e 1 Intrusion alarm central Can connect by landline Battery included e 1 Internal wired siren e 2 Remote controls to Away Arm Home Arm Disarm and panic Batteries included 1 PIR motion sensor with wall stand and battery e 1 Magnetic door sensor with duple sided tape and battery e 1 Power supply 12V 1 A e 1 Cable to connect landline e 1 User manual 1 4 Zone types and definitions Perimeter zone Detect entering spaces like doors windows and balconies Motion zone Detect inside spaces like living room hall bedrooms etc Emergency zone Detect Emergency situations like gas leakage fire smoke flood panic button and vibrations This zone keeps 24 hour monitoring status automatically http www artefects pt el AATEFECTS 2 Central Unit 2 1 Images 1 2 3 CO 6 6 QB E aa ANTENNA ALARM HOST Kar SH AARM POWER LAE 1 LES i Ss l Telephone Line Power Top 2 2 Alarm Installation Insert the plug of telephone
12. m button of the main engine and the remote alarm button will call this group number 6 5 Delete telephone numbers 1 6 Delete all the selected group telephone numbers 6 6 Set up alarm delay 7 2 set up delay warning time in the delay mode zone in seconds Here stands for the number of seconds within the range between 0 and 99 http www artefects pt wW ARTEFECTS 6 7 Alarm ringing time 4 9 The alarm ringing time without human intervention after warning Here the range of is between 0 and 30 minutes 6 8 Inquiry alarm defence area 0 9 Directly press 0 9 to inquiry the 10 latest alarm events and display alarm defence area 0 means the latest one 6 9 The state of setting up defence area 8 0 7 E Here stands for the serial number from O to 99 0 7 designates the setting mode of selected defence area O not use 1 common defence area 2 intelligent defence area 3 emergency defence area 4 multi checked defence area 5 delay alarm defence area 7 repeat triggered defence area For example press 8 2 2 then you can set up defence area 2 as the intelligent area Note When you input 99 it means all the wireless defence area will work according to this mode 6 10 Defence Areas e Intelligent defence area 2 After selecting an area as intelligent defence one the defence area is not effective it is still effective under the normal defence area which is suit
13. mitting range O 433Mhz about 100m non blocking e Dimensions 157x100x30 mm e Weight Central unit 210g Complete kit with box 803g Troubleshoot If the sensors are not working properly check the batteries and also the distance from the central e Sometimes there are other sources with wireless frequencies that can interfere with these units like baby monitor remote control toys microwaves etc Try to find it and eliminate it or change channel e In PSTN mode the alarm calling has priority over normal call H on normal call when alarm occur the line will be taken by the alarm call http www artefects pt ww AATEFECTS Index 1 PRODUCT INTRODUCTION s socos cisasisansniasdsimiconad o descts denso ta dead 4 1 1 PRODUCT SUMMARY causais sais sao Rad rsss ue nda SE da cando das ass Sudene Ed ais DUE ds doada asa duda 4 dio FEATURE EE 4 lieler A 14 ZONE TYPES AND DEFINITIONS e Ee a A 2 CENTRAL UNID e ee e ae a Ee 5 2 IMAGES 0 MM io 5 2 2 ALARM INSTALLATION EE cc E cocino 5 3 BASIC FUNCTIONS A WEEN 6 Bale SENUPDEREN SES II o e esa apli E casa dead 6 SCENE EE EEN 6 3 3 EMERGENCY ALAN EE era 6 34 INTELLIGENT DEFENSES isa ata e re li 6 4 STATUS INDICATION OF MAIN ENGINE DIGITAL TUBE sessao 6 5 DISTANCE REMOTE OPERATION METHODS ENNEN ENKER REN ENKEN RK EN ENKE EN KEEN 7 5 1 CALLING TO THE CENTRAL MI ias 7 5 2 PROCESSING METHOD AFTER RECEIVING ALARM cccccecec
14. s for opening while buzzer sounds for closing 6 5 Delayed time of setting up defence Inputting 4 Means the defence will begin after seconds when you press the button Here the range of is between O and 99 Although it can enter defence situation immediately if you repress the defence button 6 6 Open the alarm function when telephone lines disconnect 5 1 When phone lines disconnect or failure it will give alarm rings to inform 6 7 Close the alarm function when telephone lines disconnect 5 O Means main engine will not detect telephone lines disconnection or fault 6 8 Remote setup telephone ringing times 6 If the ring times calling local fixed line telephone above the setting times it will connect remote server automatically Here is the setting ring times while 0 means no remote setup 6 9 Recover factory settings 8 password The system will recover factory settings Clear telephone numbers vocal alarm alarm sounds cancel alarm delayed setting defence close the function of detecting disconnected telephone lines alarm ring time last for 5 minutes The instruction cannot delete remote controller and defence area 6 10 Setup alarm voice record O password It starts to record sounds at the place where 20 centimetres away from the main engine after correspond operations and the digital tube begin to countdown It will quit automatically and the main engine gives a
15. thin 5 30 seconds after the first trigger the system will alarm The selection of common defence area and intelligent defence area has no influence of choosing Mode 4 5 6 so you choose intelligent or common defence area while selecting any one of Mode 4 5 6 at the same time However when you reselect Mode 1 2 3 Mode 4 5 7 will be cleared 6 11 Input password password The designing password is 0000 which can be changed to another four numbers as the password 6 12 Learning remote controller 0 The intelligent learning remote controller of main engine begin to count down 10 seconds When the remote or detector is triggered in 10 seconds the main engine can distinguish automatically and give a long sound presenting the location of remove memory which means successful study All of the code learning method is the same 6 1 Delete all of the remote controllers 0 2 means delete all of the remote controllers 6 2 Designated serial learning detector 8 Connect learning detector to the designated defence area number and is the defence number For example if you want to designate a detector to Defence Area 16 only input 8 16 10 http www artefects pt el MATEFECTS 6 3 Delete all of the defence area detectors 8 22 6 Means delete the zone of the defence area detectors 99 for all zones 6 4 Use remote controller to open and close the siren sound 2 1 0 Siren sound
Download Pdf Manuals
Related Search