ColorCast 14 User Guide
Contents
1. Fig 2 fa First Light in Series Second Light in Series Cable gt MIM Ath ih thet Pa tr me I TON Oe e A O CE Female to Male Connection E 3 65 mi 34 7 cm la 0 19 0 5 cm STM MMMM aws Mounting Base Plate Alignment 50 foot leader cable to first light in series Connectors are gender specific Ensure that all lights are installed with connectors facing the same directions Female to Male connection Tenminater S c Always terminate last light in series CAUTION Ensure terminator is inserted into last fixture of each series Failure to do so can result in product failure and void the warranty 3 Continue mounting the fixtures making power data connections as you go until all lights in the series are mounted 4 Once all fixtures are mounted and connected connect the leader cable from the Data Enabler to the first fixture in the series Ensure power is off when making this connection 5 Insert the terminator into the last fixture of each light series 6 Repeat Steps Ithrough 5 for each Data Enabler in the installation until all lights are installed See Fig 3 ATTACH SAFETY CABLE Each fixture is designed for use with a safety cable When dictated by local or state code or by a Structural Engineer attach a safety cable from the fixture to the mounting surface 1 Locate the four cable ho2. depreciation is also affected by means of control thermal manage ment current levels and a host of other electrical design consider ations Color Kinetics systems are expertly engineered to optimize LED life when used under normal operating conditions Lumen depreciation information is based on LED manufacturers source life data as well as other third party testing Low temperatures and controlled effects have a beneficial effect on lumen depreciation Overall system lifetime could vary substantially based on usage and the environment in which the system is installed Temperature and effects will affect lifetime Color Kinetics rates prod uct lifetime using lumen depreciation to 50 of original light output When the fixture is running at room temperature using a color wash effect the range of lifetime is in the range of 80 000 100 000 hours This is LED manufacturers test data High output is defined as any LED device that is 1 2 watt or above For more detailed information on source life please see www colorkinetics com lifetime WARRANTY This product is sold pursuant to CK s Standard Terms and Conditions the T amp Cs which may be found at http colorkinetics com how tobuy buy terms and which contain important provisions including among others Limited Warranty exclusions and limitations on CK s liability for damages and restrictions on the remedies that are avail able to you
3. 60 Hz OUTPUT 100 240VAC 50 60 Hz POWER CONSUMPTION 30 Watts full power POWER FACTOR 0 95 or greater at 120VAC ENVIRONMENTAL SPECIFICATIONS TEMPERATURE RANGE 40 F to 122 F 40 C to 50 C operating temperature A F to 122 F 20 C to 50 C starting temperature PROTECTION RATING IP66 Suitable for wet locations TEMPERATURE MONITORING For protection from extreme temperatures the ColorCast 14 has been designed with a temperature monitoring feature If operating tempera tures rise to an unsafe level a compensation circuit is triggered and the ColorCast 14 operation is interrupted causing the lights to turn dull red To prevent additional power shut downs determine the cause of the overheating and correct the problem Power cycle the system to return to full intensity LED SOURCE LIFE In traditional lamp sources lifetime is defined as the point at which 50 of the lamps fail This is also termed Mean Time Between Failure MTBF LEDs are semiconductor devices and have a much longer MTBF than conventional sources However MTBF is not the only con sideration in determining useful life Color Kinetics uses the concept of useful light output for rating source lifetimes Like traditional sources LED output degrades over time lumen depreciation and this is the metric for SSL lifetime LED lumen depreciation is affected by numerous environmental condi tions such as ambient temperature humidity and ventilation Lumen
4. Addressing Software and instructions from http support colorkinetics com LIGHT SYSTEM COMPOSER When using ColorCast 14 fixtures in an Ethernet application the lights can be addressed after installation using the Light System Composer Management Tool TO SET DMX ADDRESS 1 With power disconnected connect a single ColorCast 14 fixture or a series of fixtures to a Data Enabler 2 Attach the DMX interface Zapi iPlayer 2 or Smart Jack 3 to the DMX IN port on the Data Enabler 3 Connect power to the Data Enabler 4 Use Zapi or Serial Addressing Software SAS to set the light address for each serial number 5 If addressing individual fixtures disconnect power and then discon nect the addressed fixture Repeat steps 1 through 5 NOTE Serial addressing gives you the option of post installatioin addressing multiple fixtures through a single Data Enabler or multiple Data Enablers using the recorded serieal numbers Refer to the Zapi User Guide or SAS Instruction Guide for details INSTALL THE DATA ENABLER Determine a location for the Data Enabler Things to remember e Install the Data Enabler according to state and local codes e Consult a Electrical Inspector to approve all wiring plans DANGER Ensure that the power source is off before wiring the Data Enabler or connecting fixtures Failure to do so can can result in seri ous injuries or death Refer to the Data Enabler Installation Guide for complete in
5. INSTALLATION GUIDE CHROMACORE BY COLOR KINETICS POWERCORE BY COLOR KINETICS OPTIBIN BY COLOR KINETICS COLOR KINETICS INCORPORATED 10 MILK STREET SUITE 1100 BOSTON MA 02108 TEL 888 FULL RGB TEL 617 423 9999 Fax 617 423 9998 INFO COLORKINETICS COM WWwW COLORKINETICS COM ColorCast 14 ITEM 123 000007 00 White 123 000007 01 Black This product is protected by one or more of the following patents U S Patent Nos 6 016 038 6 150 774 and other patents listed at http colorkinetics com patents Other patents pending 2005 2006 Color Kinetics Incorporated All rights reserved Chromacore Chromasic Color Kinetics the Color Kinetics logo ColorBlast ColorBlaze ColorBurst ColorCast ColorPlay ColorScape Direct Light iColor iColor Cove iPlayer Optibin Powercore QuickPlay Sauce the Sauce logo and Smartiuice are registered trademarks and DiMand EssentialWhite eW IntelliWhite iW and Light Without Limits are trademarks of Color Kinetics Incorporated CE OF PUB 000136 00 Rev 01 LISTED All other brand or product names are trademarks or registered trademarks of their respective owners Specifications subject to change without notice 13PE GETTING STARTED Color Kinetics ColorCast 14 offers indoor outdoor wall washing up to 15 feet and large alcove lighting in a compact linear housing It s power on board feature makes it easy to install This guide contains impor
6. les are designed into each fixture two at each end of the fixture See Fig 4 2 Thread a cable through one of the cable holes 3 Attach the safety cable to the mounting surface For the proper mounting method of the safety cable to the installa tion surface refer to a Structural Engineer or applicable standards for your specific application Fig 4 The safety cables used in the installation should meet the following minimal requirements MATERIAL 316 Stainless Steel SIZE 5 64 inch 0 78 inch nominal diameter or larger minimum break load must be greater than 400 pounds Maximum diameter is 3 16 inch CONSTRUCTION 7 x 7 49 wires performed stranded END TERMINATIONS Determined by installer and or owner MOUNTING METHOD Determined by installer or owner COLORCAST 14 SPECIFICATIONS 16 7 million 24bit additive RGB colors continuously vari able intensity output range SOURCE High intensity surface mount power LEDs COLOR RANGE BEAM ANGLE 90 at 50 of peak illuminance HOUSING Die cast aluminum Fixture 13 5 x 3 6 x 1 4 34 3 cm x 9 1 cm x 3 6 cm Base 8 9 x 1 9 x 2 22 6 cm x 4 8 cm x 5 cm CONNECTORS Over molded integral male female connectors LISTINGS C UL US CE certified COMMUNICATION SPECIFICATIONS DATA INTERFACE Color Kinetics Data Enabler CONTROL Color Kinetics full line of controllers or other DMX512 RS485 sources ELECTRICAL SPECIFICATIONS INPUT 100 240VAC 50
7. ng hardware is dictated by the mounting surface Ensure that the hardware used is appropriate for the mounting surface e Install and wire the Data Enabler before installing ColorCast 14 fix tures Refer to the Data Enabler Installation Guide STEPS TO A SUCCESSFUL INSTALLATION 1 Record serial numbers and identify fixtures as you unpack them Note the installation location on a mapping grid Address the fixtures Install the Data Enablers Install fixtures AR WN Connect power and data from the Data Enabler to the fixtures RECORD SERIAL NUMBERS 1 As you unpack the fixtures record the serial numbers Each ColorCast 14 fixture has a unique serial number programmed at the time of manufacture 2 Write the serial numbers onto a Mapping Grid 3 Using the Layout Plan assign the fixture to a layout position in the installation A Using a weatherproof label identify the fixtures installation posi tion Place an identifying label in an inconspicuous location ADDRESS THE FIXTURES The ColorCast 14 fixtures are pre addressed to light number 1 at the time of manufacture Address each fixture with a new light number as needed using one of the follow methods ZAPI Use Color Kinetics Zapi to reset the DMX address for each serial number Refer to the Zapi User Guide for step by step addressing instructions sas When using a PC with iPlayer 2 or a PC with Smart Jack 3 to address the serial numbers download the Serial
8. pecified voltage and current input Doing so will result in property damage and void the warranty CAUTION Do not exceed the maximum number of specified fixtures in a light run Doing so will result in current overload CAUTION Do not use sharp tools near or on the fixture lens Doing so will result in property damage and void the warranty CAUTION Do not hot swap Ensure that power to the fixture is off before connecting or disconnecting fixtures Hot swapping will result in property damage and void the warranty CAUTION ColorCast 14 is a Class 2 LED product with LED radiation Do not stare into beam or view directly with optical instruments NOTE The instructions and precautions set forth in this user guide are not necessarily all inclusive all conceivable or relevant to all applica tions as Color Kinetics cannot anticipate all conceivable or unique situations OWNER USER RESPONSIBILITIES It is the responsibility of the contractor installer purchaser owner and user to install maintain and operate ColorCast 14 in such a manner as to comply with all state and local laws ordinances regulations and the American National Standard Institute Safety Code PLAN THE INSTALLATION The nature and complexity of ColorCast 14 installation requires in depth planning to ensure timely successful installation with minimal complications and down time PLANNING SUGGESTIONS When planning ColorCast 14 installation Color Kinetics sugges
9. struc tions After running power and data to the Data Enabler you are ready to attach the ColorCast 14 fixtures INSTALL THE FIXTURE ColorCast 14 fixtures are installed in series The in line connectors provide an end to end fixture butt for the best visual effects Jumper cables are available to add space between the fixtures when needed Mount fixtures by using the two mounting holes located on the base Use hardware suitable for the mounting surface See Fig 1 Note The ColorCast 14 fixture can be used as a template when pre drilled pilot holes are required Hold the fixture in place and mark the two screw holes Fig 1 a 13 5 34 3 cm i 2125 5 4 cm t l i i i i Base Foot Print 1 Position the first fixture in a series and attach with two 10 mount ing screws suitable for the mounting surface Ensure that the male connector is in position to receive data and power from the leader cable See Fig 2 2 Position the next fixture in the series matching the male connec tor end to the female connector of the previously mounted fixture Attach the fixture to the surface See Fig 2 The flexible connector cables allow for up to 180 turning radius
10. sult in minor or moderate injury or property damage DANGER Ensure that main power supply is off before installation or wiring ColorCast 14 Failure to adhere to these instructions will result in death or serious injury DANGER ColorCast 14 must be installed by a qualified electrician in accordance with NEC and relevant local codes Failure to comply will result in death serious injury or property damage WARNING Do not attempt to install or use ColorCast 14 until you read and understand the installation instructions and safety labels Failure to adhere to these instructions could result in serious injury or property damage WARNING Do not use ColorCast 14 if the power cables are dam aged Doing so can result in death serious injury and property dam age WARNING As dictated by a Structural Engineer and or local code install safety cables to ColorCast 14 fixtures Failure to do so can result in injuries or property damage WARNING When using safety cables ensure that they comply to the specifications given in this user guide Failure to comply can result in injuries or property damage CAUTION Use appropriate materials and mounting methods to support the fixture adequately Failure to do so can result in property damage and void the warranty CAUTION ColorCast 14 has no user serviceable parts Do not attempt to open the fixture Doing so will result in property damage and void the warranty CAUTION Do not exceed the s
11. tant information on planning installing and operating your new ColorCast 14 For your protection read it care fully and save it for future reference Included in this box e 1 ColorCast 14 fixture e Installation Guide e Warranty and Registration cards Additional items needed e Color Kinetics Data Enabler ITEM 106 000003 04 05 e ColorCast 14 Leader Cable with terminator ITEM 108 000017 00 US or 108 000017 01 EU e 10 mounting screws M5 and tools Optional items needed e ColorCast 14 Jumper Cables ITEM 108 000016 00 01 e 3 16 OD braided safety cable and hardware as required SCOPE OF THIS USER GUIDE The goal of this user guide is to explain in an easily understandable lan guage the necessary steps to install ColorCast 14 and assure peak per formance lts intended use is for reference only by persons who are fully qualified This document should never be considered a substitute for any provision of a regulation or state and or local code IDENTIFICATION AND WARNINGS OF SAFETY HAZARDS In accordance with ANSI Z535 4 2002 the following system of iden tifying the severity of the hazards associated with the products is used DANGER I mminently hazardous situation which if not avoided will result in death or serious injury WARNING Potentially hazardous situation that if not avoided could result in death or serious injury CAUTION Potentially hazardous situation that if not avoided may re
12. ts doing the following e Consult an Electrical Inspector to approve all wiring plans e Refer to local and state codes for installation compliance e Create a Layout Plan drawing e Create a Mapping Grid Use this grid to record serial numbers for easy reference and addressing e Employ Color Kinetics Application Engineering Services INSTALLATION CONSIDERATIONS When creating your installation plan consider the following e Location of Data Enabler in relationship to lights Each Data Enabler can support up to 36 120VAC or 61 240VAC ColorCast 14 fix tures using a 50 foot field cuttable leader cable The Data Enabler supports a slightly greater or fewer number of fixtures depending on customized installation parameters NOTE By decreasing the length of the leader cable you can increase the number of ColorCast 14 fixtures per run For more information contact Color Kinetics or refer to the Configuration Calculator located at www colorkinetics com support Calculate the number of fixtures per iW Data Enabler Use the Configuration Calculator located at www colorkinetics com support to calculate the number of fixtures you can put on a data enabler The fixtures to iW Data Enabler ratio is determined by the parameters of your installation Installation parameters include all or part of the following line voltage fixture type leader length jumper lengths and wire gauge Location of the fixture and method of attaching Mounti
Download Pdf Manuals
Related Search