QuickGuide_Fingertra..
Contents
1. Quick Guide Fingertracking amp DTrack2 01 2012 Security advice Do not use any components if looking damaged Do not use any different cables than supplied with the system Fingertracking will not work correctly when modulated flash is not in sync group 1 Included in delivery v 2 active hand targets v 6 active finger thimble sets different sizes v 4 battery packs v 2 battery chargers v 2 power supplies for chargers 100 240 Volt 50 60 Hz Fingertracking hand target Carries five infrared LEDs two status LEDs a configuration dial with ten switching positions an IR receiver for the sync signal and a connector for the finger LEDs s status LEDs infrared sync receiver a power switch configuration dial The configuration dial is used to select the LED brightness and the number of fingers used in the setup The status LEDs provide the following information e green LED sync received e red LED no sync e red and green LED flashing battery low or discharged Please refer to the user manual for more details Fingertracking license Select DTrack2 Licenses Add license key for your Fingertracking device If you don t have a license key yet please click on the hardware info button to find out the serial number of your Synccard2 Please contact ART We will provide a license key consistent with your Synccard2 serial number Licenses gt new2. S tracked or not is shown by the light right next to the Hand ID handedness Cleft right setting green tracked red not tracked Then click on one of fingerset fingers F the hand signs to see your tracked fingers To start a small demo showing the handling of a virtual object l push the Demos button this opens the demos menu You have thp Calibrate a small number of simple demos available e g you can handle a virtual sphere or cube To insert the virtual object in the tracking Enter a name for the hand geometry volume place the tracked hand at a convenient position and Select handedness and the type of fingerset press the Grab object button The Fingertracking Viewer is only for demonstration and testing The calibration process is divided into two steps purposes and is only available as a 2D Viewer Step 1 Fingertracking Calibration put forth your hand and keep it still make sure that the markers are seen by all cameras fingers must be stretched and not spread the thumb must be spread I show worl CS I show Jemo cs Show hand cs I Show ingers CS fingers must be stretched and not spread all the time gently move your fingers together up and down simultaneously until calibration process is finished do not bend your fingers the thumb must be spread and must not be moved fingers down Please refer to the user manual for a more detailed description of the ART
3. bration coordinate system due to room min marker quality normal quality hd Save file Calibrate Exit Press Calibrate the calibration starts within 5 seconds Quick Guide Fingertracking amp DTrack2 Connect the finger thimble sets by plugging in the connector Fingertracking display into the hand target In DTrack2 select Display Fingertracking to see the measured coordinates of the fingers Output settings In DTrack2 select Settings Output You can either select Apply the finger thimbles to your thumb and fingers Please this computer or enter an IP address of the computer you observe the order when using the 5 finger AR set want to send data to Please make sure that the checkbox for Fingertracking data is ticked Otherwise the data will not be index middle transmitted Press Start to start measurement Display tool Fingertracking Viewer The Fingertracking Viewer is a small graphical tool which shows the hand and finger position Optionally it can be installed on the remote PC to perform a quick test of the Fingertracking setup Finger calibration After starting the viewer click the Go Online button and Select Calibration gt Fingertracking specify on which data port the viewer has to listen then click OK to connect the viewer to DTrack Afterwards choose the Hand ID you want to display If this ID is Dae EEA
4. license code currently installed licenses DTrack2 basic supported DTrack2 extended supported DTrack2 Full featured supported Fingertracking MultiUser Flystick supported expiry at Apr 09 2009 not supported Hardware Info Add license Camera and Fingertracking settings Select Settings Cameras All cameras and activate the modulated flash for a camera of sync group 1 Select Settings Fingertracking Fingertracking Settings number of hands e Hand geometry Tactile selected hands available hand geometries Hand 1D Hand geometry Simulate 5 Fingers Hand geometry Creation Date none H2 OK Cancel 4 Define the desired number of hands to be used The hand geometry remains none until you completed the calibration of the Fingertracking Press OK Inserting the battery Slide the battery in with the contact side first and then gently press the battery into the compartment until the battery snaps cauTION FIRE pany EXPLODE OF BATERY on DISPOSE gt gpecineD OE ST CHARGE On CHARGING NE T COM 1adF OR u m HEAT A CE Body calibration First of all a body calibration Calibration Body of the hand target has to be carried out Therefore select the body name Fingertracking hand body 01 for the hand target of the first hand Body Calibration 2 xI Body Fingertracking hand body 01 re cali
5. tracking system If you need further assistance please do not hesitate to contact our support ART GmbH Press Calibrate the calibration starts within 5 seconds 49 0 881 92530 00 A RT je Repeat these steps for other hands http www ar tracking de Advanced Realtime Tracking Copyright 2012 ART GmbH
Download Pdf Manuals
Related Search
QuickGuide_Fingertra..