24-port 10/100/1000 Mbps Layer 2 Managed Switch with 370W PoE
Contents
1. Hardware Installation Connecting to the Console Port and Ethernet Port 1 Attach one end of the supplied RS 232 cable to PC or terminal and the other end to the console port of the SP6524P front panel The connected terminal or PC must support the terminal emulation program 2 Connect one end of an RJ 45 cable to the Ethernet port at the front panel and the other end to PC or terminal for web interface management Cabling Requirements for 1000Base SX LX SFP Module SP6524P supports the more complex and comprehensive TP cabling in the fiber media Basically there are two categories of fiber multimode and single mode The later is categorized into several classes by the distance supported They are SX LX LHX XD and ZX From the viewpoint of connector type there mainly are LC and Bi Di LC e Gigabit Fiber with multimode LC SFP module e Gigabit Fiber with single mode LC SFP module e Gigabit Fiber with Bi Di LC 1310nm SFP module e Gigabit Fiber with Bi Di LC 1550nm SFP module For more details please refer to user manual CE Mark Warning This equipment complies with the requirements relating to electromagnetic compatibility of the essential protection requirement of Council Directive 89 336 EEC on the approximation of the laws of the Member States Company has an on going policy of upgrading its products and it may be possible that information in this document is not up to date Please check with your local distributors for the l2. atest information No part of this document can be copied or reproduced in any form without written consent from the company WEEE Directive amp Product Disposal At the end its serviceable life this product should not be treated as household or general waste It should be handed over to the applicable collection point for the recycling of electrical and electronic equipment or returned to the supplier for disposal T CE tp ra R P N 2300 0686 Configuration Web based User Interface Before using web management install the SP6524P on the network and make sure that any one of the PCs on the network can connect with the SP6524P through the web browser The default IP subnet mask username and password are as follows IP Address 192 168 1 254 Subnet Mask 255 255 255 0 User Name admin Password leave blank Login in the Console Interface When the connection between SP6524P and PC is ready turn on the PC and run a terminal emulation program or Hyper Terminal and configure its communication parameters to match the following default characteristics of the console port Baud Rate 38400 bps Data Bits 8 Parity none Stop Bit 1 After finishing the parameter settings click OK When the blank screen shows up press Enter key to bring out the login prompt Key in the admin default value for the both User name and Password use Enter key to switch then press Enter key and the command line interface
3. ation CoS e Support broadcast storm control e Support jumbo frame up to 9216K bytes e Support 802 1d STP 802 1w Rapid STP IEEE802 1s MSTP e Support 802 1x port based authentication and port security with MAC address e Support IGMPV1 IGMPV2 IGMPv3 e Support SNMPV1 SNMPV2 SNMPV3 e Support IEEE 802 3af PoE support 15 4W port at each of the 24 ports e Support non standard 30W port up to 12 ports configurable in the web user interface LED definition SP6524P LED light for port 1 24 System System Green On When the power supplied to the system Off Power off GE LED Link Act Green Light When the link through the 10 100 1000M port is successfully established PoE port Off No link detected for the port Blink When the port is activating transmitting data PoE Amber Light While PSE supply power Off No PoE power supply to connected device RESET Button To restore switch configuration to factory defaults Press the Reset button for more than 10 seconds switch configuration will be restored to factory defaults and then reboots
4. of console management appears Communicate via Micro network j iy L 4 Micronet Making Communication Easier Quick Installation Guide 24 port 10 100 1000 Mbps Layer 2 Managed Switch with 370W PoE Model No SP6524P www micronet com tw Introduction Micronet SP6524P 10 100 1000Mbps Managed Switch with 370W PoE output offers performance and a full set of layer 2 networking management features at an affordable cost suitable for high performance workgroups and server applications With 10 100 1000 Mbps RJ 45 ports and shared mini GBIC slots for fiber optic connection it delivers maximum throughput to high performance users or provides a backbone to a growing business network Package Contents Before you start installing the device verify the following items are in the package e SP6524P Managed Switch e Quick Installation Guide e Manual CD e RS 232 cable e Mounting Kits amp accessories e Power Cord Physical Description SP6524P Front Panel Rear View Key Features Compliant with IEEE802 3 10Base T IEEE802 3u 100Base TX IEEE802 3ab 1000Base T and IEEE802 3z 1000Base LX SX standards e SP6524P provide 24 RJ 45 ports of 10 100 1000Mbps and 4 shared mini GBIC slots for fiber extension e Support IEEE 802 3ad Link Aggregation up to 8 trunk groups up to 14 ports for each group e Support IEEE802 1q tag based VLAN IEEE 802 1q in q nested VLAN and IEEE802 1p traffic prioritiz
Download Pdf Manuals
Related Search