Rear-view Integration System for Jeep Grand
Contents
1. INTERFACING SOLUTIONS RVCCH 75C ww REAR VIEW INTEGRATION U CONNECT 8 4 SCREEN U CONNECT 5 6 BUTTON 2 KNOB CHRYSLER 2015 2015 300 See note below DODGE 2014 2015 Durango JEEP 2014 2016 Grand Cherokee NOTE 2015 Chrysler 300 must NOT have a separate CD slot If a separate CD slot is present 2 Piece radio use Part RVCCH 75K IMPORTANT Compatible Radio Type U CONNECT 8 4 SCREEN U CONNECT 5 6 BUTTON 2 KNOB REAR VIEW WITH VIM INTEGRATION amp CAMERA FOR DODGE and JEEP VEHICLES 2014 UP Rev 080215 We recommend reading this installation guide first before starting any work Following these instructions from Start to Finish will ensure a smooth and hassle free installation We offer telephone support M F 9 00 AM 5 00PM PDT at 1 855 822 1348 We are here to help PARTS INCLUDED 1 Camera CH 75C 20 ft Extension CH 75C Interface CH 75C Harness Instruction CAN BUS INTERFACE Camera Specifications Lens Angle 170 Degrees Resolution 420 TV Lines Min Illumination 0 2Lux Voltage 12V Operating Temp 22 F 176 F TO FACTORY NTSC lt DISPLAY Reference Lines Shutter Speed 1 60s 20us Waterproof Pixels 656 x 492 K5 52 PIN male plug PRECAUTIONS Remove the negative side of the battery to avoid any short circuits during the installation Do not install the interface near any major components or near the HVAC system This may cau2. CLOSE Attempt One Set both 5 amp 6 to the ON position Attempt Two Set 5 to On and 6 to OFF Attempt Three Set 5 to OFF and 6 to ON If none of the above solutions work out for your vehicle please contact tech support TROUBLE SHOOTING 1 No video display while in reverse Make sure the DIP switches are in the correct position INTERFACING SOLUTIONS RVCCH 75C U CONNECT 8 4 SCREEN U CONNECT 5 6 BUTTON 2 KNOB CHRYSLER 2015 2015 300 See note below DODGE 2014 2015 Durango JEEP 2014 2016 Grand Cherokee NOTE 2015 Chrysler 300 must NOT have a separate CD slot If a separate CD slot is present 2 Piece radio use Part RVCCH 75K IMPORTANT Compatible Radio Type U CONNECT 8 4 SCREEN U CONNECT 5 6 BUTTON 2 KNOB REAR VIEW WITH VIM INTEGRATION amp CAMERA FOR DODGE and JEEP VEHICLES 2014 UP Rev 080215 COMPATIBLE RADIOS a 8 4 SCREEN 5 SCREEN SEPARATE KNOBS 6 BUTTON SEPARATE KNOBS CONNECTOR VIEW Here is a Pin View of the RED 52 Pin Connector Le Ane RE i A 10 last AA NOT COMPATIBLE RADIO DOES NOT SUPPORT COLOR
3. SAME FUNCTION AS DIP 1 l NON PERMANENT RED aMMa WHITE 12V OUTPUT 12V POWER BLACK YELLOW RCA O VIDEO SIGNAL 8 PIN VIDEOIN lt TD wC Tia male plug male plug eT Cn Tn RED BARREL 12V CAM POWER 2AN ZZZ ee MAKE SURE TO TEST THE CAMERA BEFORE DOES NOT REQUIRE YOU TO RE INSTALLING THE RADIO TAP FOR REVERSE SIGNAL TO FACTORY SIGNAL IS FROM MODULE HARNESS SETTING THE DIP SWITCHES PARKING LINE The parking lines are there to assist you while reversing 1 On Enable VIM PERMANENT To activate the parking lines simply connect the GREEN wires located Z n near the 4 pin camera connector in the back 4 On Enable Force RVC To invert the image simply connect the WHITE wires 5 May Vary 6 May Vary GREEN Dip 1 Activates the Video In Motion feature The DIP switch is the permanent solution for keeping the VIM unlocked Use the Green wire with a toggle switch for a non permanent solution Switch not included Dip 2 Activates the Rear View Camera image when the vehicle is in YELLOW reverse gear Dip 4 Activates the Force Rear View Camera while driving RED Force Rear View Camera allows the driver to view the rear view camera when not in the Reverse gear Dip 5 amp 6 Varies these switches are defaulted to OFF If the radio is having turn on issues please try the following What the lines mean Green Line CLEAR Yellow Line GETTING CLOSE Red Line WARNING VERY
4. se damage or overheating to the vehicle PRELIMINARY Please read the entire manual before installing this interface INSTALLING THE CAMERA AND CABLE 1 Remove the rear lip panel 2 Drill a 5 8 size hole in the available location 3 Fish the wires thought the drilled hole and through the pass through into the trunk cargo area Make video and power connection 5 Remove the factory radio to gain access to the factory connectors 5 Route the wires towards the radio and make the power and video connections For powering up the camera use the 12V OUTPUT White Wire See Overview 6 Test the camera before re installing the radio Note The camera is defaulted to power down after 10 seconds FORCE REVERSE The force reverse is used to view the back up camera when the vehicle is not in reverse gear Allows you to view what is in the back while driving SEEK UP To activate this feature make sure the dip switch settings are correct Then simply press the center button once on the Left Hand steering wheel control PRESS Note The camera is defaulted to power down after 10 seconds SEEK DN CONNECTIONS OVERVIEW 4 PIN BARREL CONNECT FOR CAMERA POWER AND SIGNAL oD e 1 On Enable VIM PERMANENT ii gt 2 On Enable RVC eo eee OPTIONAL T eA me Force RVC TOGGLE SWITCH a 20FT 2 id NOT a P E EXTENTION GREEN 12V POWER SWITCH
Download Pdf Manuals
Related Search