Home

Honeywell Vista-250FBP User Manual

1. 8 5 After a few seconds the keypad displays the status of the original partition for the keypad Also this mode will end in approximately 120 seconds if no keys are pressed 27 Accessing Other Panels cont d Multi Partition Multi Panel Mode 98 To access the multi partition multi panel mode perform the following steps 1 Enter your security code 8 8 2 Thekeypad displays the following PANELnn 12345678 STATUS XXXXXXXXx where nn panel id 01 08 12345678 are the partition s and XXXXXXXX is the status of each partition of that panel Possible status indications indude A Armed Away S Armed Stay M Armed Maximum I Armed Instant R Ready N Not Ready B Bypassed Ready Alarm T Trouble F Fire Alarm P AC Power Failure L Low System Battery C Comm Fail NOTES See the table that follows for priority of displays A under a partition number indicates the user does NOT have access to that partition Use the following keys to perform a function in this mode Press to attempt to disarm all partitions Press to attempt to arm AWAY all partitions Press to attempt to arm STAY all partitions Press 4 to attempt to arm MAXIMUM all partitions Press to attempt to arm INSTANT all partitions Press to read the status of the next panel Press to read the status of the previous panel Press 0 to exit mode After a few seconds the keypad di
2. key can be pressed in place of the security code when arming the system The security code must always be used to disarm the system however 15 Security Codes amp Authority Levels cont d Authority Levels 16 Authority levels define the system functions a particular user can perform Depending on the authority assigned to you there are certain system functions you may be prohibited from performing In summary there are six authority levels each having certain system restrictions as shown below Level 1 Master Level 2 Manager Level 3 Operator A Level 4 Operator B Level 5 Operator C Level 6 Duress Can perform all system functions in assigned partitions and can add delete or change Manager and Operator level users Master codes are added by the Installer Can perform system functions in assigned partitions and can add delete or change Operator level users Can perform system functions in assigned partitions but cannot add or delete other users Same as Operator A except Operator B cannot bypass zones of protection Can arm the system in assigned partitions but cannot disarm the system unless the system was armed with this code This code is typically assigned to someone who has a need to arm disarm the system only at certain times such as a baby sitter Can arm and disarm the system but also sends a silent panic alarm to the central station if that service is connected To view yo
3. control panels Single Partition Single Panel displays status of a partition on a remote control panel and allows control of that remote control panel Multi Partition Multi Panel Mode displays status and allows arming disarming of multiple partitions at once on a remote control panel Multi Panel View Mode displays status and allows arming disarming of multiple remote control panels at a time NOTE A user will not be able to access or view partitions or panels that they have not been assigned to Single Partition Single Panel Mode To access the single partition single panel mode perform the following steps 1 2 3 4 Enter your security code 8 6 Enter the panel ID 72 01 08 of the panel you want to link to Enter the partition number of the panel The keypad displays AWAITING PANEL LINK After a few seconds the keypad displays the status of the partition along with the panel ID number and partition number flashing in the upper right hand corner The user now has full control of the remote control panel All functions can be performed except the following e Those limited by the user s authority level e Theuser cannot enter Installer Program mode e Theuser cannot execute another panel linking mode NOTE To execute another panel linking mode or to access a different remote panel the user must first exit this mode return to the original control panel To exit enter your security code
4. The Load Number LN assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop which is used by the device to prevent overloading The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the Load Numbers of all the devices does not exceed 100 AVIS L tiquette du minist re des Communications du Canada identifie le mat riel homologu Cette tiquette certifie que le mat riel est conforme certaines normes de protection d exploitation et de s curit des r seaux de t l communications Le minist re n assure toutefois pas que le mat riel fonctionnera la satisfaction de l utilisateur Avant d installer ce mat riel l utilisateur doit s assurer qu il est permis de le raccorder aux installations de l entreprise locale de t l communications Le mat riel doit galement tre install en suivant une m thode accept e de raccordement Dans certains cas les fils int rieurs de l entreprise utilis s pour un service individuel la ligne unique peuvent tre prolong s au moyen d un dispositif homologu de raccordement cordon prolongateur t l phonique interne L abonn ne doit pas oublier qu il est possible que la conformit aux conditions nonc es ci dessus n emp chet pas la d gradation du service dans certaines situations Actuellement les entreprises de t l communications ne permettent pas que l
5. The Panel Linking is ideal for multi building environments e g a shopping mall college campus etc The system provides the following three modes to access other linked control panels e Single Partition Single Panel displays status of a partition on a remote control panel and allows control of that remote control panel e Multi Partition Multi Panel Mode displays status and allows arming disarming of multiple partitions at once on a remote control panel e Multi Panel View Mode displays status and allows arming disarming of multiple remote control panels at a time Your system s sensing devices have been assigned to various zones For example the sensing device on your Entry Exit door may have been assigned to zone 001 sensing devices on windows in the master bedroom to zone 002 and so on These numbers will appear on the display along with an alpha descriptor for that zone if programmed when an alarm or trouble condition occurs Fire Protection The fire protection portion of your security system if used is always on and will sound an alarm if a fire condition is detected Refer to the FIRE ALARM SYSTEM section for important information concerning fire protection smoke detectors and planning emergency exit routes from your facility System Overview cont d Burglary Protection Alarms The burglary protection portion of your system must be turned on or armed before it will sense burglary ala
6. 1 Open and close each protected door and window in turn and listen for three beeps Each faulted protection point should appear on the display 2 Walk in front of any motion detectors if used and listen for three beeps as movement is detected wireless motion detectors have a 3 1 2 minute lockout between trips Each detector s should appear on the display when it is activated 3 Follow the manufacturer s instructions to test all smoke detectors to ensure that all are functioning properly Each detector should appear on the display when activated 4 When all protection points have been checked there should be no zone identification numbers displayed If a problem is experienced with any protection point no confirming sounds no display CALL FOR SERVICE IMMEDIATELY 5 Turn off Test mode by entering the security code the OFF key 62 Fire Alarm System Your fire alarm system if installed is on 24 hours a day providing continuous protection In the event of an emergency the smoke and heat detectors automatically send signals to your Control triggering a loud interrupting sound from the keypad and the optional exterior sounders FIRE appears at your keypad and remains on until you silence the alarm In Case Of Fire Alarm 1 Should you become aware of a fire emergency before your detectors sense the problem go to your nearest keypad and manually initiate an alarm by pressing the panic key assigned as FIRE emergency
7. NO 1 YES transmitter has been supplied and has not yet been assigned to a user Press 1 if a button transmitter will be assigned to this user Otherwise press 0 ENTER BUTTON ZN If assigning a button transmitter this prompt will 001 250 appear Enter the button s zone number see your installer for zone number MULTI ACCESS 0 NO 1 YES GLOBAL ARM 0 NO 1 YES PART 2 SHOP 0 NO 1 YES XMIT USER DATA 0 NO 1 YES INDV USER PGM 1 YES 0 NO Security Codes amp Authority Levels cont d If you as a user have access to other partitions the keypad will prompt for ability of this new user to access GOTO those partitions Press O NO or 1 YES If no the system activates this user code and exits Add a User mode If yes the keypad prompts for the Global Arm option for this user Press 1 YES if this user will be allowed to try to arm more than one partition at the same time Press O if this user will arm only his assigned partition The keypad now prompts for the user s access to the next partition see GOTO command Again press 0 or 1 If yes the system will automatically assign a user number for use in that partition and will prompt for authority level and global arm options for this user within the partition see previous steps If the user number is from 001 050 this prompt appears Answer YES 1 to have the system send the user s attributes to all the other control panels that are linked to this
8. O NO 1 YES O NO 0 Press to continue QUIT MENU MODE Enter 1 YES or O NO 1 YES O0O NO Press to continue 59 Event Log Procedures General Information The system has the ability to record various events in a history log wherein each event is recorded in one of five categories listed below with the time and date of its occurrence The Event Log holds up to 1000 events with the oldest event being replaced by the logging of any new event after the log is full Using an alpha keypad the Event Log can be viewed one category at a time or can display all events regardless of category ALL EVENT LOG The system also allows selection of displaying the COMPLETE log or only those events occurring since the last installer service RECENT In addition events in the other partitions can be viewed by users authorized to access those partitions Note that events are displayed in chronological order from most recent to oldest 60 To Display The Event Log 1 Enter CODE 6 0 2 Select the display mode RECENT Displays only those events occurring since last Event Log Clear command was executed COMPLETE Displays complete event log up to 1000 events Press the desired key O or 1 ENTER 0 RECENT 3 Select the partition 0 8 Enter the partition number for the partition whose events are to be displayed Entering O NO will display all partitions events SCAN LOG BY PART O NO 1 8 P
9. System Low Battery L 6 Trouble T 7 Bypass B 8 Not Ready N 9 Ready R 10 Armed STAY S 11 Armed AWAY A 12 Armed INSTANT I 13 Armed MAXIMUM M Checking For Open Zones Using the READY Key Before arming your system all protected doors windows and other protection zones must be closed or bypassed see BY PASSING section Otherwise the keypad will display a Not Ready message Using the READY key will display all zones that are faulted making it easier for you to secure any open zones To show faulted zones DISARMED PRESS Note Some keypads light a green LED when TO SHOW FAULTS thesystemis ready If not lit the system is not ready to be armed READY 1 Do not enter security code but simply press FAULT 005 FRONT Typical fault display UPSTAIRS BEDROOM 2 DISARMED Secure or bypass the zones displayed before READY TO ARM arming the system The Ready message will be displayedt when all protection zones have been either closed or bypassed T NOTE All or part of this message may be replaced by a customized message programmed by the installer Bear this in mind whenever the instructions indicate that the DISARMED or READY message will be displayed 31 Displaying All Zone Descriptors Using the READY Key 389 The Alpha Keypads can also display all the zone descriptors that are programmed in your system The abbreviated instructions for the READY key will appear first followed by t
10. any wire runs to the control communicator Plug the control communicator into a different outlet so that it and the receiver are on different branch circuits If necessary the user should consult the dealer or an experienced radio television technician for additional suggestions The user or installer may find the following booklet prepared by the Federal Communications Commission helpful Interference Handbook This booklet is available from the U S Government Printing Office Washington DC 20402 The user shall not make any changes or modifications to the equipment unless authorized by the Installation Instructions or User s Manual Unauthorized changes or modifications could void the user s authority to operate the equipment IN THE EVENT OF TELEPHONE OPERATIONAL PROBLEMS In the event of telephone operational problems disconnect the control by removing the plug from the RJ31X CA38A in Canada telephone wall jack We recommend that your certified installer demonstrate disconnecting the phones on installation of the system Do not disconnect the phone connection inside the control communicator Doing so will result in the loss of your phone lines If the regular phone works correctly after the control communicator has been disconnected from the phone lines the control communicator has a problem and should be returned for repair If upon disconnection of the control communicator there is still a problem on the line notify the tel
11. control If you answer NO 0 the system displays the following prompt on the next page Answer YES 1 to link to another control panel and manually enter the user into partition s in that control panel If you answer NO 0 the system scrolls through each partition displaying a summary of the user s attributes in each partition see next prompt 19 Security Codes amp Authority Levels cont d PART 1 AO WHSE USER 003 AUTH 3G To Change a User s Code When all partitions have been displayed the keypad will scroll through the partition s to which access has been assigned and will display the user number authority level and global arm option for each The G after the authority level indicates that the global arm feature is active for this user in the displayed partition The indicates the partition from which this user can be changed or deleted The at the end of the second line indicates that this user sends open close reports Open close reporting is automatically active for any users added by you if you have open close reporting active CODE L Enter Master or Manager code and press the key 4 user number to be changed 2 Enter the new code for that user ADD NEW USER 0 2 NO 1 YES USER 002 CHANGED SUCCESSFULLY 90 The system will recognize that the user number is already in use and will prompt whether or not this is a new user Enter O to change the existing user s code to
12. if programmed by the installer and hold down for at least 2 seconds Evacuate all occupants from the premises If flames and or smoke are present leave the premises and notify your local Fire Department immediately If no flames or smoke are apparent investigate the cause of the alarm The descriptor of the zone s in alarm appears at the keypad Silencing A Fire Alarm 1 Silence the alarm by entering your code and pressing the OFF key To clear the display enter your code and press the OFF key again If the keypad does not indicate a READY condition after the second OFF sequence press the READY key to display the zone s that are faulted Be sure to check that smoke detectors are not responding to smoke or heat producing objects in their vicinity Should this be the case eliminate the source of heat or smoke If this does not remedy the problem there may still be smoke in the detector Clear it by fanning the detector for about 30 seconds You can clear the display by entering your code the OFF key 63 Fire Alarm System cont d Fire Display Lock If several zones produce an alarm before any are silenced the system can be programmed to lock the keypad display with the first zone that produced an alarm Ask your installer if your system has been activated with this feature To display the other zone s press the key for each zone Also the A B or C keys can be programmed to scroll the keypad di
13. installer can be accessed in this manner To GOTO another partition READY 1 Enter your security code then press partition number 0 8 Entering partition number 0 will return the keypad toits original partition 2 The keypad will remain in the new partition PART X COMPLETE until directed to go to another partition or until 2 minutes has elapsed with no keypad activity AAAA alpha descriptor programmed by the installer X partition number Global Arming 99 The Global Arming option may be assigned for use by some users If Global Arming was enabled for use with your security code a keypad prompt message shown below appears after pressing one of the arming function keys STAY INSTANT AWAY MAXIMUM OFF ARM P12345678 The prompt displays all the partitions The user HIT 0 8 XXX X may only arm disarm the partitions they are assigned access to To select the partition s that are to be armed enter the desired number 1 8 An X will appear under that partition Entering a partition s number again will delete the X and that partition will not arm when this prompt is exited Pressing O will turn all partitions the user is assigned access to on off When completed press to exit All the partitions with the X will then arm disarm Accessing Other Partitions cont d Global Arming Notes e When performing a Global Arm if there are faults in any of the selected partitions the system will
14. must be READY TO ARM to perform this function Refer to the FUNCTIONS OF THE KEYPAD section for descriptions of each key function Phone Access amp Voice Response Capability Your system may include a 4285 or 4286 VIP module that will permit you to access the system via a Touch tone phone either on premises or by call in when away The phone access feature will enable you to do the following e Receive synthesized voice messages over the telephone regarding the status of the security system e Arm and disarm the system and perform most function commands via the telephone with voice confirmation provided after each command entry e Control 4204 4204CF relays devices and lights and appliances through the 70 Manual Relay Activation mode Complete information regarding the use of this feature is provided in a separate manual entitled PHONE ACCESS USER S GUIDE which accompanies the 4285 or 4286 VIP module About The Keypads General IMPORTANT If the keypad beeps rapidly upon entering the premises it indicates that an alarm has occurred during your absence LEAVE IMMEDIATELY and CONTACT THE POLICE from a safe location nearby NOTE If you have a Symphony Advanced User Interface connected to your system refer to the Symphony User Guide for operating instructions Your keypads allow you to control all system functions The keypads feature a telephone style digital keypad and a Liquid Crystal Display LCD that show
15. must disarm the system within the entry delay period or an alarm will occur The system provides three STAY modes STAY mode 1 2 and 3 STAY modes 1 and 2 when activated automatically bypass specific zones assigned by the your installer to each of the STAY modes STAY mode 3 when activated automatically bypasses all zones assigned to STAY modes 1 AND 2 Check with your installer for a list of the zones that are bypassed during each STAY mode Close all perimeter windows and doors before arming see CHECKING FOR OPEN ZONES section STAY 1 Enter your security code and press 1 for STAY Mode 1 Enter your security code and press 2 for STAY Mode 2 Enter your security code and press 3 for STAY Mode 3 NOTE If none of the zones in a partition are assigned to Stay mode 2 then when the user enters User Code 3 STAY all zones assigned to Stay mode 1 are automatically bypassed 2 ARMED STAY 1 The keypad beeps three times displays the ZONE BYPASSED armed message and indicates which STAY mode 1 2 or 3 Note ZONE BYPASSED in this display simply indicates that some zones of protection are not armed when using STAY mode Arming Perimeter Only With Entry Delay ON cont d Auto STAY Arming Auto stay allows the system to automatically bypass certain zones if upon arming none of the entry exit zones are faulted during the exit delay time no one exits the premises The system provides an option
16. on raccorde leur mat riel aux prises d abonn s sauf dans les cas precis pr vus par les tarifs particuliers de ces entreprises Les r parations du mat riel homologu doivent tre effectu es pas un centre d entretien canadien autoris par le fournisseur La compagnie de l utilisateur de d sign t l communications peut demander d brancher un appareil la suite de r parations ou de modifications effectu es par l utilisateur ou cause de mauvais fonctionnement Pour sa propre protection l utilisateur doit s assurer que tous les fils de mise en terre de la source d nergie lectrique des lignes t l phoniques de r seau de conduites d eau s il y en a soient raccord s ensemble Cette pr caution est particuli rement importante dans les r gions rurales Avertissement L utilisateur ne doit pas tenter de faire ces raccordements lui m me il doit avoir recours un service d inspection des installations lectriques ou un lectricien Selon le cas L indice de charge IC assign chaque dispositif terminal pour viter toute surcharge indique le pourcentage de la charge totale qui peut tre raccord un circuit t l phonique boucl utilis par ce dispositif La terminaison du circuit boucl peut tre constitu e de n importe quelle combinaison de dispositifs pourvu que la somme des indices de charge de l ensemble des dispositifs ne d passe pas 100 75 WARNING THE LIMITATIONS
17. soon as possible Also you will be advised of your right to file a complaint with the FCC if you believe necessary The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of the equipment If this happens the telephone company will provide advance notice in order for you to make the necessary modifications in order to maintain uninterrupted service If trouble is experienced with this equipment please contact the manufacturer for repair and warranty information If the trouble is causing harm to the telephone network the telephone company may request you remove the equipment from the network until the problem is resolved There are no user serviceable components in this product and all necessary repairs must be made by the manufacturer Other repair methods may invalidate the FCC registration on this product This equipment cannot be used on telephone company provided coin service Connection to Party Line Service is subject to state tariffs This equipment is hearing aid compatible When programming or making test calls to an emergency number briefly explain to the dispatcher the reason for the call Perform such activities in the off peak hours such as early or late evening 74 CANADIAN DEPARTMENT OF COMMUNICATIONS DOC STATEMENT NOTICE The Canadian Department of Communications label identifies certified equipment This certification means that t
18. the code entered in step 3 The system will confirm that the change is allowed based on authorization level and if so will put the new code into effect Note that if changing one s own code the system will prompt for the new code to be re entered This prevents accidentally changing one s own code Security Codes amp Authority Levels cont d To Delete a User CODE 1 Enter Master or Manager code and press the key user number to be deleted 2 Enter Master or Manager code first entered OK TO DELETE The system will recognize that the User number 0 NO 1 YES is already in use and will prompt to confirm that it should be deleted Press 0 NO or 1 YES USER CODE If yes that user s code will be removed from all DELETED partitions to which it was assigned and all authorization levels and other information about that user will be deleted Note that a user can only be deleted from the partition in which it was first assigned and can only be deleted by a user with a higher authority level A User s security code cannot be deleted by oneself 21 Accessing Other Partitions To Access Another Partition Each keypad is assigned a default partition for display purposes and will show only that partition s information But if the user is authorized a keypad in one partition can be used to perform system functions in other partitions by using the GOTO command Note that only those partitions authorized and programmed by the
19. you to override the normal schedules programmed by the installer Temporary schedules can be in effect for up to one week and take effect as soon as they are programmed They are comprised of an arming closing time window and a disarming opening time window A time window is simply a defined period of time at the end of which arming or disarming will occur Before programming use a worksheet similar to the one below to plan your schedule This will make it easier when actually programming the schedule Arm Disarm Mon Tue Wed Thu Fri Sat Tom KT E WW p w po pi Disarm Window J T e Start Time HOM TI III Hn ERG RT DEE WEE StopTime DOMM J Am Window o Start Time HOM III II pd o MEAT ee Stop Time HH MM Using Schedules cont d Programming Temporary Schedules B9 Temporary schedules only affect the partition from which it is entered Temporary schedules can be reused at later dates simply by scrolling by pressing to the DAYS prompt described below and activating the appropriate days This should be considered when defining daily time windows Note that only users with authority level of manager or higher can program temporary schedules To program temporary schedules 1 Enter your security code 2 Press the 4 key followed by 81 3 Thefollowing prompts will appear MON DISARM WIND 07 45AM
20. your installer Loss of system battery power is not indicated or annunciated by the keypad warnings are for loss of AC power only 79 UL NOTICE This is a GRADE A system FEDERAL COMMUNICATIONS COMMISSION FCC Part 15 STATEMENT This equipment has been tested to FCC requirements and has been found acceptable for use The FCC requires the following statement for your information This equipment generates and uses radio frequency energy and if not installed and used properly that is in strict accordance with the manufacturer s instructions may cause interference to radio and television reception It has been type tested and found to comply with the limits for a Class B computing device in accordance with the specifications in Part 15 of FCC Rules which are designed to provide reasonable protection against such interference in a residential installation However there is no guarantee that interference will not occur in a particular installation If this equipment does cause interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures If using an indoor antenna have a quality outdoor antenna installed Reorient the receiving antenna until interference is reduced or eliminated Move the receiver away from the control communicator Move the antenna leads away from
21. 0 will turn all days on off The temporary schedule will only be in effect for the days which have the letter x underneath them As the week progresses the days are reset tothe deactive state When completed press to exit the temporary schedule entry mode 53 Programming Device Timers General Information Device timers consist of an ON time amp an OFF time and selected days of the week in which they are active There are up to 20 timers that can be used to control various devices such as lights or appliances Your installer will have programmed the appropriate devices into the system up to 96 devices can be programmed Each timer controls a single device designated as an output number that you select For example timer 1 might be set to turn the porch lights on at 7 00pm and turn them off at 11 00pm Timer 2 might turn on the air conditioner Monday Friday at 4 30pm to cool the premises before you arrive at 5 00pm and turn it off at 10 00pm when you are retiring for the night If desired different timers can control the same device For example timer 2 could be used Monday F riday as in the previous example and timer 3 could be set to turn the air conditioner on and off at different times Saturday and Sunday To enter the device timer menu mode Enter your security code then press the key followed by 83 OUTPUT TIMER Up to 20 timers can be programmed E ach timer 01 20 00 QUIT 01 is identified by a number
22. 08 45AM MON ARM WINDOW 07 45AM 08 45AM TUE DISARM WIND 07 45AM 08 45AM The cursor will be positioned on the tens of hours digit of the start time for Monday s disarm window Enter the desired hour Press to move to the minutes field The minutes are entered in the same manner The AM PM indication is changed by hitting any key 0 9 while the cursor is under the letter A P position Repeat for the stop time entry Press the key to move to the arming window for Monday Press to move to the next screen display without making changes The cursor will be positioned on the tens of hours digit of the start time for the arm window Repeat the previous steps to enter the start and stop time for Monday s arming window After the windows for that day have been completed the system will prompt for disarm and arm time windows for the next day Repeat the procedure for all days of the week When all of the days have been completed the system will ask which days are to be activated Using Schedules cont d DAYS MTWTESS This is the prompt that actually activates the HIT 0 7 X X temporary schedule and allows the temporary schedule to be customized to a particular week s needs To select the days which are to be activated enter the desired number 1 7 Monday 1 An X will appear under that day indicating the previously entered schedule for that day is active Entering a day s number again will deactivate that day Pressing
23. 1 20 Enter the desired timer number to be programmed 1 20 Press to accept entry 06 07 00P 11 45P If that timer number has already been programmed a summary screen will appear In this example 06 Timer 04 Output Device affected by this timer PORCH LITE Output Descriptor for Device 4 07 00PM Start Time 11 45PM Stop Time Press to continue af nor for Enter the desired output device number 1 96 i oo S the number is entered the device s description will appear To delete a previously programmed timer enter 00 as the output number BA Programming Device Timers cont d 00 ON TIME 00 00 PM 00 OFF TIME 00 00 PM 00 DAYS MTWTFSS HITO 7 XX 00 PERMANENT O NO 1 YES 0 Enter the time you want the device turned on using 00 01 11 59 format When the display shows the desired time press the key to move to the AM PM field Press any key 0 9 to change the AM PM indication Enter 00 00 if this timer is not being used to turn something ON for the days selected below ex using one timer to turn lights on one day and using another timer to turn them off on another day Enter the time you want the device turned off using 00 01 11 59 format When the display shows the desired time press the key to move to the AM PM field Press any key 0 9 to change the AM PM indication Enter 00 00 if this timer is not being used to turn something OFF for the days selected below ex using one
24. 15 sec Keypad only TWO SHORT BEEPS SYSTEM IS ABOUT TO Opened Zone identifications will appear once every 5 sec AUTOMATICALLY EXIT TEST n Keypad only MODE ONE BEEP LOW BATTERY AT A TRANSMITTER LO BAT displayed with description of transmitter every 60 sec Keypad only Keypad only Red ARMED indicator is lit THREE SHORT a ARM STAY OR INSTANT a ARMED STAY ZONE BYPASSED or ARMED BEEPS b ZONE OPENED WHILE SYSTEM INSTANT ZONE BYPASSED is displayed Red Keypad only IS IN CHIME MODE ARMED indicator is lit c ENTRY WARNING CHIME displayed descriptor of open protection zone will be displayed if the x key is pressed DISARM SYSTEM OR ALARM WILL OCCUR is displayed RAPID BEEPING a TROUBLE CHECK displayed Descriptor of troubled Keypad only b AC POWER LOSS ALERT protection zone is displayed c MEMORY OF ALARM AC LOSS displayed may alternate with other displays that may be present FIRE or ALARM is displayed descriptor of zone in alarm is displayed SLOW BEEPING a ENTRY DELAY WARNING DISARM SYSTEM OR ALARM WILL OCCUR is Keypad only b EXIT DELAY WARNING displayed Exceeding the delay time without if programmed disarming causes alarm ARMED AWAY or ARMED MAXIMUM is displayed along with You May Exit Now If bell is used as Notification Appliance fire alarm is pulsed ring burglary audible emergency is steady ring Entry warning may consist of three short beeps or slow continuous beeping as programmed by
25. 3 digit entries Enter code Press BYPASS 6 Press Enter code Press BYPASS 6 Press Enter Group Number 01 15 Bypass Zones Quick Bypass Chime Mode Enter code Press CHIME 9 Keypad will sound if doors or windows are ree Pres OMWEI TE seconds View User Capabilities GOTO Partition Enter user s code Press Dk Enter security code Press s Enter partition number 1 8 0 returns to default partition Bypassed zones are unprotected and will not cause an alarm if violated Bypasses all faulted zones automatically Bypasses all zones assigned to the group Displays partitions amp authority levels assigned to the user Allows a user at one keypad to perform functions in another partition if that user is authorized to do so Self Help Press and hold any function key for Will display abbreviated instructions for the key at least 5 seconds pressed Add a User Enter master manager code Master amp Manager level users can add users to Press CODE 8 Enter new user s user number Enter code for that user Enter authority for that user in this partition 1 5 Follow prompts 1 Yes 0 No Enter master manager code Press CODE 8 Enter user s 3 digit number Change a User s Code Enter new code for that user Press 0 No at prompt 70 the system each with its own code and authority level Master amp Manager level users can change
26. 4 Using the 9 E 44 VIEWING ALARM COMPANY MESSAGE S ie sie penc egere 45 General Information 45 PANIC KEY S 2 shed eee 46 Using Panic Keys ese see eee eee 46 SPEED KEY MACROS 47 General Information 47 DENNO HE 47 EX6GCUtlIg tite ite neret ds 48 Using Speed Key For Fire Alarm FUNCION et eui ter she ree sg 48 ACCESS DOOR CONTROL 49 General Information 49 EXeCU lting ende de Peers 49 USING 70 RELAY MENU MODE 50 General Information 50 USING SCHEDULES 51 Delaying the Closing Time iese ees 51 Temporary Open Close Schedules 51 Programming Temporary Schedules 52 PROGRAMMING DEVICE TIMERS 54 General Information 54 Randomize Output Device Times 56 USING 77 INSTANT ACTIVATION MODE ds sind 57 EVENT LOG PROCEDURES 60 General Information 60 To Display The Event Log 60 TESTING THE SYSTEM TO BE CONDUCTED WEEKLY 62 Using the 5 TEST Key 62 Testing Your System cc cee ese eee 62 FIRE ALARM SYSTEM 63 In Case Of Fire Alarm 63 Silencing A Fire Alarm 63 Fire Display Lock cee Ee ee 64 Fire Drill Test Code 69 64 TROUBLE CONDITIONS 65 Typical Trouble Displays 65 Power Failure ctr 66
27. ADY TO ARM displays ready to arm message 33 Bypassing Protection Zones cont d Quick Bypass Your system allows you to easily bypass all open faulted zones without having to enter zone numbers individually Note All bypasses are removed when an OFF sequence security code plus OFF is performed To use the Quick Bypass feature BYPASS 1 Enter your security code and press 6 then press t 2 BYPASS 007 FRONT in a few moments all open zones will be UPSTAIRS BEDROOM displayed along with the word BYPASS Wait Typical bypass message for these zones to be displayed before arming Arming the system before bypassed zones are displayed eliminates all bypasses 3 DISARMED BYPASS Arm the system as usual when the keypad READY TO ARM displays the ready to arm message Bypassed zones are unprotected and will not cause an alarm when violated while your system is armed Displaying Bypassed Zones 34 For determining what zones have been previously bypassed Bypassed zones can be displayed only when system is disarmed BYPASS 1 Enter your security code and press 6 2 Wait for all bypassed zones to be sequentially displayed Bypassing Protection Zones cont d Group Bypass Your system allows you to easily bypass a group of zones without having to enter zone numbers individually The system provides up to 15 groups There is no limit to the number of zones that may be assigned to any
28. ART Event Logging Procedures continued 4 Use the 3 amp 1 keys for next and previous categories respectively to display the categories of events Press 8 to select a category and display the first event Press 8 again for each subsequent event Shows burglary alarm occurred in zone 3 C03 of partition 1 P1 at 12 02AM on J anuary 1 P1 01 01 12 02AM Typical BURGLARY C003 Event Log Display After the last event has been displayed the END OF EVENT LOG message appears for a few seconds then the system automatically displays the RECENT COMPLETE mode select screen again see step 2 5 To EXIT the Event Log Press at any time ALARM EVENT LOG Typical TYPE CCC UUU Category Select Screen ALARM EVENT LOG Displays time and date for zones that have either caused an alarm or have been restored in the selected partition CHECK EVENT LOG Displays time and date for zones that have caused a trouble or supervisory condition in the selected partition BYPASS EVENT LOG Displays time and date for zones that have been bypassed in the partition OPEN EVENT LOG Displays time date and user number or 6 character descriptor for the user if programmed for each arming and disarming of the system for the partition selected SYSTEM EVENT LOG Displays time and date for system problems such as AC Loss low battery etc regardless of partition ALL EVENT LOG Displays all categories of events in chr
29. CALL FOR SERVICE IMMEDIATELY if AC power cannot be restored SERVICING INFORMATION Your local ADEMCO dealer is the person best qualified to service your alarm system Arranging some kind of regular service program with him is advisable Your local ADEMCO dealer is Name Address Phone 66 Emergency Evacuation Establish and regularly practice a plan of escape in the event of fire The following steps are recommended by the National Fire Protection Association 1 Position your detector or your interior and or exterior sounders so that they can be heard by all occupants Determine two means of escape from each room One path of escape should lead to the door that permits normal exit from the building The other may be a window should your path be impassable Station an escape ladder at such windows if there is a long drop to the ground Sketch a floor plan of the building Show windows doors stairs and rooftops that can be used to escape Indicate escape routes for each room Keep these routes free from obstruction and post copies of the escape routes in every room Assure that all fire doors are shut while you in the building This will prevent deadly smoke from entering while you escape Try the door If the door is hot check your alternate escape route If the door is cool open it cautiously Be prepared to slam the door if smoke or heat rushes in Where smoke is present crawl on the ground
30. DY INDICATOR 13 Protect Access Door 49 eie dn EE EE E 13 Quick Arming sse 15 Quick BYPASS ee ee e 34 QUICK EXIT sai 2 conem EE 41 Quick Guide 70 71 Randomize Output Devices 56 Ready ihe eere 31 READY cet tee ener ded 44 Ready Key ssn eee hist 31 Relay commande AAA 57 78 Relay Menu Mode 50 Replacing Batteries 68 R BUTTON ioni 18 Routine Care 69 Schedules nm memini 8 51 Security Code 15 Security Codes 15 Sensing Devices sees 6 Silencing A Fire Alarm 63 Silent Emergency 46 Single Partition Single Panel Mode 27 Smoke Deiectors iese ee ke ee ee 62 Speed Keys EE ER ER ER RE ea 47 SPEED KEY inn nee ree ees 8 EE AO RE T 7 22 STAN EE fetu 43 STAY Mode eo eise 36 SVMPNONY EE 5 10 System LO Bat 66 System Overview 5 T l S MANE eet tene mee 5 Temporary Schedules 51 52 Temporary USerS AA 18 Test gy nie sine 62 Test mode EE OE HD 62 Testing Your System 62 Time Window 51 IR SE 65 Trouble Condition 65 UNABLE TO ARM LOBBY 25 User Edit Mode User Numbers User s Instructions Using 77 Instant Activation Mode 57 WARRANTY A 79 Wireless Sensor 68 Zone Bypassed AN 36
31. E 7 ARMED INDICATOR ees ee eene ee ee 13 Audible Emergency 46 Audible Signals sse 72 Authority Level 15 Authority Levels ese ee ee ee 16 17 Auto STAY Arming eene 37 NEE 7 22 PAW AN EE 43 AWAY mode ee ee ee ee ee 39 battery life 2 25 68 elle LE TE 5 Burglary Protection 7 Bypass Access Door 49 Bypass Commands see ke ee ee 58 Bypass Zones 33 Bypassing ER rete rei HE 33 eds AE EE EE DA 65 Change a User s Code 20 Change User Code i ee ee Re 17 OHEGK ees Ee E a 65 Chim aed catt tem 7 44 Closing H eie 51 Common Lobby 25 Delaying Closing Time 51 Delete a User 21 Delete User Code 17 Descriptors eene intet 32 Device Timers 8 54 DISA OR AE ES ER 42 Displays for Multi Partition and Multi Panel Ok ER EE EE N 30 DOG ois aside AE T 75 BT RE DE 16 Dur ss Gode EE nece 15 Emergehoy Eie SE ee ESEL Ie petere 5 Entry Delays iacet hat 14 SUE 6 Event Log Procedures 60 Exit Delay iseer eee ReRE IER 14 Exit User Edit Mode 17 GG uten EE EE IE 73 IDEA s NE OE RE N 5 46 SICA E 63 Fire Display Lock 64 FIRE DRILL ACTIVE AA 64 Fire Drill Test eine 64 Fire Protection ges er KEER Gee eg engin 6 GLOBAL E 19 Global Arming 22 EE ise ee Deiere 19 GOTO EE 22 GOTO Command 8
32. ED TO ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN 12 MONTHS FROM DATE OF ORIGINAL PURCHASE IN NO CASE SHALL SELLER BE LIABLE TO ANYONE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY EXPRESS OR IMPLIED OR UPON ANY OTHER BASIS OF LIABILITY WHATSOEVER EVEN IF THE LOSS OR DAMAGE IS CAUSED BY THE SELLER S OWN NEGLIGENCE OR FAULT Some states do not allow limitation on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you Seller does not represent that the product may not be compromised or circumvented that the product will prevent any personal injury or property loss by burglary robbery fire or otherwise or that the product will in all cases provide adequate warning or protection Buyer understands that a properly installed and maintained alarm may only reduce the risk of a burglary robbery fire or other events occurring without providing an alarm but it is not insurance or a guarantee that such will not occur or that there will be no personal injury or property loss as a result CONSEQUENTLY SELLER SHALL HAVE NO LIABILITY FOR ANY PERSONAL INJURY PROPERTY DAMAGE OR OTHER LOSS BASED ON A CLAIM THE PRODUCT FAILED TO GIVE WARNING HOWEVER IF SELLER IS HELD LIABLE WHETHER DI RECTLY OR INDIRECTLY FOR ANY LOSS OR DAMAGE ARISING UNDER THIS LIMITED WARRANTY OR OTHERWISE REGARDLESS O
33. EMERGENCY EVACUATION 67 MAINTAINING YOUR SYSTEM 68 Taking Care of Your System 68 Replacing Batteries in Wireless SENSOIS c cci ei cei md ees E 68 Silencing Low Battery Warning Tones at the Keypad sse 69 Routine Care eda certes 69 QUICK GUIDE TO SYSTEM FUNCTIONS Ee en ee ecco peau coc 70 SUMMARY OF AUDIBLE NOTIFICATION 72 INDEX een een Nr 77 General System Overview Congratulations on your ownership of an ADEMCO Partitioned Security System You ve made a wise decision in choosing it for it represents the latest in security protection technology today ADEMCO is the world s largest manufacturer of security systems and millions of premises are protected by ADEMCO systems This system offers you three forms of protection burglary fire and emergency To realize the system s full potential it is important that you feel comfortable in operating it Your system consists of at least one Keypad which provides full control of system operation various sensors which provide perimeter and interior burglary protection plus a selected number of strategically placed smoke or combustion detectors designed to provide early warningin case of fire The system uses microcomputer technology to monitor all protection zones and system status and provides appropriate information for display on the Keypad s used with the system and initiates appropriate alarms Your system may also have been
34. F CAUSE OR ORIGIN SELLER MAXIMUM LIABILITY SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT WHICH SHALL BE THE COMPLETE AND EXCLUSIVE REMEDY AGAINST SELLER This warranty gives you specific legal rights and you may also have other rights which vary from state to state No increase or alteration written or verbal to this warranty is authorized 79 ADEMCO GROUP 165 Eileen Way Syosset New York 11791 Copyright 2002 PITTWAY CORPORATION K0377 8 02
35. G OTHER PARTITIONS 22 To Access Another Partition 22 Global Arming eene 22 Master Keypad Operation 23 Common Lobby Operation 25 How User Codes Affect the Common LOBBY oru EET 26 ACCESSING OTHER PANELS 27 Single Partition Single Panel Mode 27 Multi Partition Multi Panel Mode 28 Multi Panel View Mode 29 Priority of Displays for Multi Partition and Multi Panel Modes 30 CHECKING FOR OPEN ZONES 31 Using the READY Key 81 DISPLAYING ALL ZONE DESCRIPTORS EE 32 Using the x READY key 32 BYPASSING PROTECTION ZONES 33 Using the BYPASS Key 33 Quick Bypass sse 34 Displaying Bypassed Zones 34 Group Bypass 35 ARMING PERIMETER ONLY 36 Using the STAY Keane 36 Auto STAY Arming 0 ees see ee eee 37 ARMING PERIMETER ONLY 38 Using the INSTANT Regester 38 ARMING ALL PROTECTION 39 Using the AWAY Key 39 ARMING ALL PROTECTION 40 Using the MAXIMUM ke 40 QUICK CA WEE 41 Using the EE AE 41 DISARMING AND SILENCING e dE 42 Using the OFF 42 Memory of Alarm 42 USING THE KEYSWITCH 43 ETC 43 ATTI EA N EN 43 Disarmirig irr ette 43 CHIME MODE ees sesse see ee ee ee ee ee ee ee 4
36. Grant Access Door 49 Group Bypass 35 How to Use Panel Linking 27 HSENS site os Ee ve SE a te De cie ipee 66 ISL ee LLLA MAA ER 7 22 INSTANT GEGEE SEN EE iene 14 INSTANT mode 38 ee ER AR ER tts 5 Keypad back lighting eess 10 Koypads EER OE RE 10 KeySWItGh EE ee EEN 43 LO Bath rss epe EE EE EO 66 e le 68 Low Battery Warning s e 69 dd Kam EE ER IE OE 66 MAGCIOS c os EE 8 47 Manager is RA RE t OE 16 LESC RE NE 16 Master Keypad 9 23 MAXIMUM ugin to eio cor Ge EE dee 7 22 MAXIMUM aaaea rompre DIM 14 MAXIMUM mode AA 40 Memory of Alarm ccceeecceeeeeeeeeeees 7 42 Ee GT 45 Modem Comm sse 66 MULTI ACCESS essen 19 Multi Panel View Mode sees 29 Multi Partition Multi Panel Mode see 28 NIGHT a N RE EE EE EE 38 Not EG ie ER eee 31 OER EG EE ee iu 22 42 Open ZONES EE ecce ESE Ne ia 31 Open Close Schedules 51 Open Close Windows esses 58 Op rator A ES inserer 16 Operator Bissau 16 Operator Cine nin ee ee NE 16 OUTPUT TIMER ee ee ee ke ee ee 54 Panel Linking 6 27 Panic Keys 46 PANIC KEYS iii 13 Partitioned Security System 5 Partitioned System 6 Personal Emergency 46 Phone Access 9 POWER REA
37. LPHA DISPLAY WINDOW A 2 line 32 character Liquid Crystal Display LCD Displays protection point identification and system status messages and user instructions Disarms the burglary portion of the system silences alarms and audible trouble indicators and clears visual alarm trouble after the problem bas been corrected perimeter and interior burglary protection by sensing an intruder s movements through protected interior areas as well as guarding protected doors windows etc Late arrivals can enter through an entry delay zone without causing an alarm if the system is disarmed before the entry delay time expires Completely arms both 3 STAY Arms the perimeter burglary protection guarding protected doors windows and other perimeter protection points and sounds an alarm if one is opened Allows automatic bypassing of certain areas which allows movement within your house without causing an alarm Late arrivals can enter through an entry delay zone without causing an alarm if the system is disarmed before the entry delay time expires See ARMING PERIMETER ONLY for a full explanation of the STAY key 12 Arms in manner similar to AWAY mode but eliminates the entry delay period thus providing maximum protection An alarm will occur immediately upon opening any protection point including entry delay zones 5 TEST Tests the system and alarm sounder if disarmed 6 BYPASS protect
38. OF THIS ALARM SYSTEM While this system is an advanced design security system it does not offer guaranteed protection against burglary or fire or other emergency Any alarm system whether commercial or residential is subject to compromise or failure to warn for a variety of reasons For example ntruders may gain access through unprotected openings or have the technical sophistication to bypass an alarm sensor or disconnect an alarm warning device Intrusion detectors e g passive infrared detectors smoke detectors and many other sensing devices will not work without power Battery operated devices will not work without batteries with dead batteries or if the batteries are not put in properly Devices powered solely by AC will not work if their AC power supply is cut off for any reason however briefly Signals sent by wireless transmitters may be blocked or reflected by metal before they reach the alarm receiver Even if the signal path has been recently checked during a weekly test blockage can occur if a metal object is moved into the path A user may not be able to reach a panic or emergency button quickly enough While smoke detectors have played a key role in reducing residential fire deaths in the United States they may not activate or provide early warning for a variety of reasons in as many as 35 of all fires according to data published by the Federal Emergency Management Agency Some of the reasons smoke detectors used in conjunction wi
39. VISTA 126FBP VISTA 250F BP Commercial Fire and Burglary Partitioned Security System with Scheduling User Guide ADEMCO K0377 8 02 TABLE OF CONTENTS SYSTEM OVERVIEW s 5 General IR N EE GE aN 5 A Partitioned System 6 Panel Linking eee 6 Vds tp MITT 6 Fire Protectlon 4i eerte 6 Burglary Protection 7 Alatimg rec ten erii ste 7 Memory of Alarm 7 Speed Key Macros 8 Using Gchedules iii ee ee Re 8 Device Timers 8 To Access Another Partition GOTO Command 8 Master Keypad Operation 9 Self Help Feature 9 Phone Access amp Voice Response Capability rene tn tts 9 ABOUT THE KEYPADS 10 General Ge ee GE ee 10 The Alpha Keypad ees ee ee ee 10 FUNCTIONS OF THE KEYPAD 11 ENTRY EXIM DELAYS ice 14 General Information ss 14 SECURITY CODES amp AUTHORITY LEVELS asie 15 General Information 15 Duress Code A 15 Quick Arming tee eee tenet eee 15 Authority Levels 16 General Rules on Authority Levels and Changes ene EE EE aa dts 17 To Exit User Edit Mode 17 To Add a Ser iens 18 To Change a User s Code iese 20 To Delete a User 21 ACCESSIN
40. Zone Descriptors 32 ZONES EL EER i tuba etus 6 ADEMCO ONE YEAR LIMITED WARRANTY Alarm Device Manufacturing Company a Division of Pittway Corporation and its divisions subsidiaries and affiliates Seller 165 Eileen Way Syosset New York 11791 warrants its security equipment the product to be free from defects in materials and workmanship for one year from date of original purchase under normal use and service Seller s obligation is limited to repairing or replacing at its option free of charge for parts labor or transportation any product proven to be defective in materials or workmanship under normal use and service Seller shall have no obligation under this warranty or otherwise if the product is altered or improperly repaired or serviced by anyone other than the Seller In case of defect contact the security professional who installed and maintains your security equipment or the Seller for product repair This one year Limited Warranty is in lieu of all other express warranties obligations or liabilities THERE ARE NO EXPRESS WARRANTIES WHICH EXTEND BEYOND THE FACE HEREOF ANY IMPLIED WARRANTIES OBLIGATIONS OR LIABILITIES MADE BY SELLER IN CONNECTION WITH THIS PRODUCT INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE ARE LIMITED IN DURATION TO A PERIOD OF ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE ANY ACTION FOR BREACH OF ANY WARRANTY IN CLUDING BUT NOT LIMIT
41. a fire alarm message to the central station and will uniquely sound external Notification Appliance Circuits FIRE plus a zone number would also be displayed Speed Key Macros General Information Defining The A B C and or D keys can be used to activate a string of commands up to 32 keystrokes each These commands are known as a macro and are stored in the system s memory Typical Speed K ey functions include e Arming sequences that involve first bypassing certain zones before arming e Seldom used but repeatable sequences e Relay activation sequences NOTE If a speedkey function includes an arming sequence and the user executing it has global arming all partitions the user can global arm will arm To program a macro enter your user code D The following appears ENTER SPEED KEY 01 32 00 QUIT Enter the 2 digit Speed Key number 01 32 being defined and press Enter up to 32 keystrokes A Speed Key sequence can include different commands Press the D key to separate different commands For example you may want to perform the following sequence GOTO partition 2 Enter 2 Bypass zones 10 amp 11 Press bypass 6 then the zone numbers 010 amp 011 Arm in maximum mode Press maximum 4 key Return to partition 1 Enter 1 To program that Speed K ey sequence type the following 2 D 6010011 D 4 D 1 D D Note that the D
42. access to that partition Also in order for a user of any partition to log onto the Master partition Partition 9 to view the status of all partitions and to perform any functions at the Master keypad that user must have access to all partitions Otherwise access will be denied 93 Accessing Other Partitions cont d 24 The following is an example of what would be displayed for a fault condition on Zone 002 Loading Dock Window on Partition 1 Warehouse when logging on from a keypad on Partition 9 WHSE DISARMED HIT FOR FAULTS This is the normal display that appears at Partition 1 s keypad s Pressing x will display FAULT 002 LOADING DOCK WINDOW Additional zone faults will be displayed one at a time To display a new partition s status press Partition Nol This will display the status of the new partition The Armed LED on a Master keypad will be lit only if all partitions have been armed successfully The Ready LED will be lit only if all partitions are ready to arm The sounder on a Master keypad will reflect the sound of the most critical condition on all of the partitions The priority of the sounds is as follows A Pulsing fire alarm sounds B Steady burglar alarm sounds C Trouble sounds The sounder may be silenced by pressing any key on the Master keypad Accessing Other Partitions cont d Common Lobby Operation When an installation consists of a partition that is sha
43. ccess control functions may also be executed use your security code 77 See Using 77 Instant Activation Mode later in this manual 49 Using 70 Relay Menu Mode General Information Your system may be set up so that certain lights or other devices can be turned on or off by using the 70 command from either a keypad or a telephone keypad if 4285 or 4286 VIP module is used Ask your installer if this has been done in your system To activate relays from a keypad enter 4 digit security code 7 70 Follow the keypad prompts described below To activate relays using a telephone and 4285 or 4286 VIP module first dial the 2 digit phone access code When the system acknowledges the access enter 4 digit security code 70 The following prompts voice responses will begin ENTER DEVICE NO Voice ENTER DEVICE CODE NOW 00 QUIT 01 Enter the2 digit number of the device to be activated Note that if an invalid number is entered the system will simply ask you to reenter the number NN DEVICE IS OFF Voice voicedescriptor DEVICE nn ON OFF HIT O OFF 1 ON FOR voicedescriptor ON ENTER 1 FOR voice descriptor OFF ENTER 0 Press 0 or 1 to turn the device off or on respectively nn represents the 2 digit device number and voice descriptor is the relay voice descriptor programmed by the installer NN DEVICE IS OFF Voice voicedescriptor DEVICE nn ON OFF TO HIT THE KEY EXIT ENTER 00 NOW From a keypa
44. ction INSTANT 1 Enter your security code and press 1 for INSTANT Mode 1 Enter your security code and press 2 for INSTANT Mode 2 Enter your security code and press 3 for INSTANT Mode 3 NOTE If none of the zones in a partition are assigned to INSTANT mode 2 then when the user enters User Code 7 INSTANT all zones assigned to INSTANT mode 1 are automatically bypassed 2 ARMED INSTANT1 The keypad beeps three times displays the ZONE BYPASSED armed message and indicates which INSTANT mode 1 2 or 3 Note ZONE BYPASSED in this display simply indicates that some zones of protection are not armed when using INSTANT mode Arming All Protection With Entry Delay ON Using the 2 AWAY Key Use this key when no one will be staying on the premises When armed in AWAY mode the system will sound an alarm if a protected door or window is opened or if any movement is detected inside the premises You may leave through the entrance door during the exit delay period without causing an alarm Y ou may also reenter through the entrance door but must disarm the system within the entry delay period or an alarm will occur Close all perimeter windows and doors before arming see CHECKING FOR OPEN ZONES section AWAY 1 Enter your security code and press 2 ARMED AWAY The keypad will beep twice and will display the YOU MAY EXIT NOW armed message Note The Y OU MAY EXIT NOW portion of the mes
45. d press to continue The ENTER DEVICE NO prompt will appear From a telephone keypad enter 00 to exit or enter the next relay number to be programmed The current on off state of that relay will be annunciated as described above Alternatively if 6 seconds elapses with no key depression the 4285 or 4286 VIP module will annundate the ENTER DEVICE CODE NOW message _ 50 Using Schedules Delaying the Closing Time Your system s programmed schedules may automatically arm the system at a predetermined time In the event a user must stay on the premises later than usual users with master or manager authority levels can manually delay the automatic arming closing time up to 2 hours To delay the closing time 1 Enter your security code master or manager authority levels only 2 Press the key followed by 82 3 A menu prompt will be displayed asking for the number of hours of delay CLOSING DELAY Enter the desired number of hours of delay 1 or 2 KEY 0 2 HOURS The system automatically exits this mode after entry Notethat the delay is from the scheduled closing time not from the time the command is entered IMPORTANT The selected delay cannot be reduced once it is set A 1 hour delay can be increased to 2 hours though 4 The system will automatically send a message to the central station informing them that the programmed schedule has been changed Temporary Open Close Schedules Temporary schedules allow
46. do not walk upright Smoke rises and may overcome you Clearer air is near the floor Escape quickly don t panic Establish a common meeting place outdoors away from your house where everyone can meet and then take steps to contact the authorities and account for those missing Choose someone to assure that nobody returns to the house many die going back E Maintaining Your System Taking Care of Your System The components of your security system are designed to be as free of maintenance as possible However there are some things you can do to make sure that your system is in reliable working condition 1 Test your system weekly See TESTING THE SYSTEM and FIRE ALARM SYSTEM sections 2 Test the system after any alarm occurs Replacing Batteries in Wireless Sensors Wireless sensors Each wireless sensor in your system has a 9 volt or 3 volt battery The system may not have detects a low battery in any wireless sensor including smoke detectors the been used in your d security system Optional personal emergency transmitter and the optional portable wireless keypad A low battery in a portable wireless keypad is detected as soon as one of its keys is pressed and the keypad will display 00 Alkaline batteries provide a minimum of 1 year of operation and in most units and applications provide 2 4 years of service Actual battery life will depend on the environment in which the sensor is used the number o
47. ds See SUMMARY OF AUDIBLE NOTIFICATION section for information which will help you to distinguish between FIRE and BURGLARY alarm sounds IMPORTANT If you return and the main burglary sounder is on DO NOT enter the premises but call the police from a nearby safe location If you return after an alarm has occurred and the main sounder has shut itself off the keypad will beep rapidly upon entering indicating that an alarm has occurred during your absence LEAVE IMMEDIATELY and CONTACT THE POLICE from a nearby safe location To disarm the system and silence burglary or fire alarms OFF 1 Enter your security code and press DISARMED READY TO ARM 2 The Ready message will be displayed if no alarms have occurred while armed and the keypad will beep once to confirm that the system is disarmed Memory of Alarm 42 The keypad displays the zone number and type of alarm for any zone that has an alarm condition These messages will remain displayed until deared by a user If an alarm has occurred note the zone number displayed on the keypad and repeat step 1 above to clear the Memory of Alarm and restore the Ready message display If the Ready message will not display go to the displayed zone and remedy the fault close windows etc If the fault cannot be remedied notify the alarm agency If the system was armed when the alarm occurred repeat step 1 twice once to disarm the system a second time to clear the displa
48. e again to turn off the random schedule 2 Enter your security code and press followed by 42 This is the same as the method above except the randomization occurs only on devices with activation times within 6 PM and 5 AM Enter the same sequence again to turn off the random schedule Using 77 Instant Activation Mode The 77 Instant Activation Mode is used to activate outputs bypass zones etc immediately upon exiting the 77 Mode The actions that may be activated are relay commands arm disarm commands zone bypassing commands and open close access conditions Relay Commands Action Code Action Specifier 01 Relay On Relay 02 Relay Off Relay 03 Relay Close for 2 seconds Relay 04 Relay Close XX minutes Relay 05 Relay Close YY seconds Relay 06 Relay Group On Relay Group 07 Relay Group Off Relay Group 08 Relay Group Close for 2 seconds Relay Group 09 Relay Group Close XX minutes Relay Group 10 Relay Group Close YY seconds Relay Group Check with your installer for the amount of time Arm Disarm Commands Activation times 1 Beginning 2 End 3 During are the only valid choices for automatic arming and disarming functions During can be used to arm or disarm the control for a specific time only For example if during is selected with Arm STAY the system will automatically Arm STAY at the beginning of the window and automatically disarm at the end of the window Action Code Act
49. eed Keys can be programmed for the following fire alarm functions e Fire Sounder Silence The key when pressed silences fire alarms e Display Next Fire Alarm The key when pressed causes the keypad to display the next fire alarm in the system e Display Previous Fire Alarm The key when pressed causes the keypad to display the previous fire alarm in the system NOTE Each of these functions requires programming by the installer If you want to use a Speed Key for one of these functions ask your installer to program the system accordingly Access Door Control General Information Executing Your system may be set up such that a locked access door such as in a lobby can be unlocked momentarily or for a specific period of time using a keypad command Ask your installer if this has been done in our system There are several entries that can be entered at the keypad to activate this command 1 Enter your security code 0 The door will unlock for 2 seconds 2 Enter your security code 73 or security code 74 access point The door will unlock for a specific period of time 3 Enter your security code 4 75 access point function The functions available are Grant Protect and Bypass Grant will temporarily unlock a door to allow an access Protect will cause a door to unlock only when a valid access is received Bypass will cause a door to be permanently unlocked to allow continuous access 4 A
50. electrical devices is subject to component failure Even though this equipment is designed to last as long as 10 years the electronic components could fail at any time The most common cause of an alarm system not functioning when an intrusion or fire occurs is inadequate maintenance This alarm system should be tested weekly to make sure all sensors and transmitters are working properly Installing an alarm system may make one eligible for lower insurance rates but an alarm system is not a substitute for insurance Homeowners property owners and renters should continue to act prudently in protecting themselves and continue to insure their lives and property We continue to develop new and improved protection devices Users of alarm systems owe it to themselves and their loved ones to learn about these developments 76 70 command 50 4285 or 4286 VIP module 9 50 Le 66 Access Another Partition 22 Access Control Commands 58 ACCESS DOOF use ete entes 49 Action Code ie ee metes 57 Action Specifier esses 57 Add a User usines ae 18 ADD NEW USER aise Minas 20 Add User Code 17 Ademco Dealer 66 Advanced User Interface 5 10 Alarm OE ER EO dee 7 Alkaline batteries 68 Alpha Keypads AAA 10 Arm Disarm Commands ss 57 le E
51. enter a Summary Mode F aulted zones in all the selected partitions will be displayed These faults must be corrected or bypassed This Summary Mode will end in approximately 120 seconds if no keys are pressed e When performing a Global Disarm if any of the selected partitions has a condition which would cause the keypad to beep e g alarm memory or a trouble condition the system enters a Summary Mode and displays the condition This Summary Mode will end in approximately 120 seconds if no keys are pressed Master Keypad Operation A Master keypad is one that reflects the status of the entire system Partitions 1 8 on its display This is useful because it eliminates the need for a security officer in a building to have to log on to various partitions from one partition s keypad to find out where an alarm has occurred A description of a typical display follows SYSTEM 12345678 STATUS RRNNATXB The status of each partition is directly below the partition number on the display Possible status indications include A Armed Away S Armed Stay M Armed Maximum Armed Instant R Ready N Not Ready B Bypassed Ready Alarm T Trouble F FireAlarm P AC Power Failure L Low System Battery C Comm Fail To obtain more information regarding a particular partition enter x Partition No i e 4 This will allow viewing only of that partition In order to affect that partition the user must log on with a code that has
52. ephone company that they have a problem and request prompt repair service The user may not under any circumstances in or out of warranty attempt any service or repairs to the system It must be returned to the factory or an authorized service agency for all repairs Bee fc e FEDERAL COMMUNICATIONS COMMISSION FCC Part 68 NOTICE This equipment complies with Part 68 of the FCC rules On the front cover of this equipment is a label that contains among other information the FCC registration number and ringer equivalence number REN for this equipment If requested this information must be provided to the telephone company This equipment uses the following jacks An RJ31X is used to connect this equipment to the telephone network The REN is used to determine the quantity of devices which may be connected to the telephone line Excessive RENs on the telephone line may result in the devices not ringing in response to an incoming call In most but not all areas the sum of the RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to the line as determined by the total RENS contact the telephone company to determine the maximum REN for the calling area If this equipment causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required If advance notice is not practical the telephone company will notify the customer as
53. et to alert you to the opening of a door or window while it is disarmed by using CHIME mode When activated three tones will sound at the Keypad whenever a protected perimeter door or window is opened and the Not Ready message will be displayed Pressing the READY key will display the open protection points Note that Chime mode can be activated only when the system is disarmed 1 To turn Chime Mode on enter the security code and press 9 CHIME MODE ON The CHIME MODE ON message will appear for about two seconds then disappear To display this message again to determine whether chime mode is on or off simply press and hold down the CHIME key for 5 seconds 2 Toturn Chime Mode off enter the security code and press 9 again CHIME MODE OFF The CHIME MODE OFF message will appear for about two seconds then disappear To display this message again to determine whether chime mode is on or off simply press and hold down the CHIME key for 5 seconds 44 Viewing Alarm Company Messages General Information Users of the system may periodically receive messages on their display screens from their monitoring agency or installer When message is waiting to be viewed the message shown below will appear MESSAGE PRESS 0 FOR 5 SECS 1 Press and hold down 0 key for 5 seconds 2 The message could take up to four screens to display all the information available NOTE Any message sent by the central station d
54. f signals that the transmitter in the sensor has had to send and the specific type of sensor Factors such as humidity high or low temperatures or large swings in temperature may all lead to the reduction of actual battery life in an installation If you have a low battery in a wireless sensor a low battery message is displayed on the keypad In addition a battery operated smoke detector with a low battery also emits a single chirp sound once approximately every 20 30 seconds identifying itself as the smoke detector with the weak battery If you do not replace a smoke detector s low battery the smoke detector may sound continuously as if there were a fire alarm Note The low battery message comes on as a warning that battery replacement in indicated sensor s is due within 30 days In the meantime the sensor s causing the low battery indication is still fully operational Important Use only batteries recommended by your installer as replacement 68 Maintaining Your System cont d Silencing Low Battery Warning Tones at the Keypad The keypad s warning tones can be silenced by performing an OFF sequence code plus OFF key but the Keypad s low battery message display will remain on as a reminder that you have a low battery condition in one or more of your sensors When you replace the weak battery with a fresh one the sensor will send a good battery signal to the control as soon as the sensor is activated openi
55. he equipment meets certain telecommunications network protective operational and safety requirements The Department does not guarantee the equipment will operate to the user s satisfaction Before installing this equipment users should ensure that it is permissible to be connected to the facilities of the local telecommunications company The equipment must also be installed using an acceptable method of connection In some cases the company s inside wiring associated with a single line individual service may be extended by means of certified connector assembly telephone extension cord The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier Any repairs or alterations made by the user to this equipment or equipment malfunctions may give the telecommunications company cause to request the user to disconnect the equipment Users should ensure for their own protection that the electrical ground connections of the power utility telephone lines and internal metallic water pipe system if present are connected together This precaution may be particularly important in rural areas Caution User should not attempt to make such connections themselves but should contact the appropriate electric inspection authority or electrician as appropriate
56. he zone descriptors Displaying all descriptors is useful when you need to know the zone number of a particular zone as when bypassing zones The Disarmed Ready to arm message must be displayed before zone descriptors can be displayed READY Press the key and hold down for at least 5 seconds Bypassing Protection Zones Using the 6 BYPASS Key This key is used when you want to arm your system with one or more zones intentionally unprotected Bypassed zones are unprotected and will not cause an alarm when violated while your system is armed All bypasses are removed when an OFF sequence security code plus OFF is performed Bypasses are also removed if the arming procedure that follows the bypass command is not successful Note The system will not allow fire or emergency zones to be bypassed To bypass zones the system must be disarmed first BYPASS 1 Enter your security code and press 6 2 Enter zone number s for the zones to be bypassed e g 001 002 003 etc Important All single digit numbers must be preceded by 00 for example enter 001 for zone 1 3 BYPASS 007 FRONT When finished the keypad will display the UPSTAIRS BEDROOM word BYPASS along with each bypassed zone Typical bypass message number Wait for these zones to be displayed before arming Arming the system before bypassed zones are displayed eliminates all bypasses 4 DISARMED BYPASS Arm the system as usual when the keypad RE
57. ion Specifier 20 Arm STAY Partition s 21 ArmAWAY Partition s 22 Disarm Partition s 23 ForceArm STAY Auto bypass faulted zns Partition s 24 Force Arm AWAY Auto bypass faulted zns Partition s 25 ArmINSTANT Partition s 26 ArmMAXIMUM Partition s 57 Using 77 Instant Activation Mode cont d _ 58 Bypass Commands Activation times 1 Beginning 2 End 3 During are the only valid choices for bypass commands If 3 During is selected for auto bypassing the system bypasses the zone s specified on a particular zone list at the beginning of the window and unbypasses them at the end of the window If it is selected for auto unbypassing the system removes the bypass at the beginning of the window and restores the bypass at the end of the window Action Code Action Specifier 30 Auto bypass Zone list Zone list 31 Autounbypass Zone list Zone list Open Close Windows Activation time 3 During is the only valid choice for these commands Action Code Action Specifier 40 Enable Opening Window by partition Partition s 41 Enable Closing Window by partition Partition s 42 Enable Access Window for access group Access Group Access Control Commands Action Code Action Specifier 55 Access Point Grant Access Point 56 Access Point Grant with Override Access Point 57 Access Point Protect Access Point 58 Access Point Bypass Access Point 59 Access Point Lock Access Point 60 Access Point Exit Acces
58. ion zones from being monitored by the system Displays previously bypassed protection zones 7INSTANT Arms in manner similar to STAY mode but turns off the entry delay period offering greater security while inside and not expecting any late arrivals An alarm will occur immediately upon opening any perimeter protection point including entry delay zones 8 CODE Allows the entry of additional user codes that can be given to other users of the system 9 CHIME Turns on amp off the CHIME mode When on any entry through a protected delay or perimeter zone while the system is disarmed will cause a tone to sound at the K eypad s Removes individual Functions Of The Keypad cont d READY When depressed prior to arming the system the keypad will display all open protection zones within the keypad s home partition This key is also used to display all zone descriptors that have been programmed for your system by holding the key down for at least 5 seconds s Permits ARMING of the system without use of a security code Quick Arm if programmed KEYS 0 9 Used to enter your individual security access code s LED READY INDICATOR GREEN Lit indicates system is ready to be armed while unlit indicates system not ready LED ARMED INDICATOR RED Lit when the system has been armed STAY AWAY INSTANT or MAXIMUM LED SUPER INDICATOR GREEN Lit when a supervisory condition exists in the sy
59. itions Arms Disarmed NO NO NO NO YES YES NO YES NO NO YES YES YES YES NO NO YES ENTRY NOT ALLOWED DE Accessing Other Partitions cont d How User Codes Affect the Common Lobby 96 Codes with Global Arming If your code is given global arming when it is defined the system displays a prompt that allows you to pick and choose the partitions to be armed or disarmed This eliminates the automatic operation of the lobby Keep in mind however that if attempting to arm all the partitions you have access to and another affecting partition is disarmed one you do not have access to you will not be able to arm the lobby and the message UNABLE TO ARM LOBBY PARTITON will be displayed Codes with Non Global Arming If arming with a non global code the lobby partition operation will be automatic as described in the previous table Other Methods of Arming Disarming When arming or disarming a partition that affects and or arms the common lobby in one of the following manners lobby logic remains active e Quick Arm e Keyswitch e Wireless Button e Wireless Keypad Accessing Other Panels If the user is authorized a keypad in one panel can be used to perform system functions in other panels by using one of the panel linking methods described below Note that only users 001 to 050 can be authorized to access other panels The system provides three modes to access other linked
60. key is pressed after each command Press D twice to complete the entry and exit NOTE When defining Speed Key sequences do not use the key to represent Quick Arming The system uses the code entered in response to the prompt to initiate commands in a Speed Key sequence so the quick arm key is unnecessary The system interprets the use of the key in a Speed Key sequence as its designated function only 47 Speed Key Macros cont d Executing To execute a Speed Key sequence do the following If a lettered key A B C has been assigned as a Speed Key press and hold down the appropriate key about 2 seconds If a user code is required for any part of the Speed Key sequence the following prompt appears Otherwise the Speed K ey sequence automatically begins ENTER USER CODE TKK KOK Enter your user code The defined Speed Key sequence will begin automatically To activate a Speed Key not assigned to the A B C keys press and hold down the D key for 2 seconds until the following prompt appears ENTER SPEED KEY 01 32 00 QUIT Enter the desired Speed Key number If a user code is required for any part of the Speed Key sequence the following prompt appears Otherwise the Speed Key sequence automatically begins ENTER USER CODE 3o0 Enter your user code The programmed Speed K ey sequence will begin automatically Using Speed Key For Fire Alarm Function 48 Instead of a macro sequence the Sp
61. lti partition multi panel mode and multi panel view mode Access Control Enter security code Enter 0 Activate access relay for current partition Enter security code Press Enter 73 Request to enter or exit at a console Enter security code Press Enter 74 Enter access point number Request to enter or exit at an access point Enter security code Press Enter 75 Enter access point number Enter state 1 3 Change the access point state Enter security code Press Enter 79 Perform an access control card function 71 Summary Of Audible Notification Alpha Display Keypads SOUND CAUSE DISPLAY LOUD FIRE ALARM FIRE is displayed descriptor of zone in alarm is INTERRUPTED displayed Keypad amp External LOUD BURGLARY AUDIBLE EMERGENCY ALARM is displayed descriptor of zone in alarm is CONTINUOUS ALARM also displayed Keypad amp External ONE SHORT BEEP a SYSTEM DISARM a DISARMED READY TO ARM is displayed not repeated b SYSTEM ARMING ATTEMPT b The number and descriptor of the open protection Keypad only WITH AN OPEN ZONE zone is displayed c BYPASS VERIFY c Numbers and descriptors of the bypassed protection zones are displayed One beep is heard for each zone displayed Subsequently the following is displayed DISARMED BYPASS Ready to Arm ONE SHORT BEEP SYSTEM IS IN TEST MODE Opened Zone identifications will appear once every
62. ng closing of door window etc causing the low battery display to turn off If the sensor is not activated the display will automatically clear within approximately 1 hour Routine Care e Treat the components of your security system as you would any other electrical equipment Do not slam sensor protected doors or windows e Keep dust from accumulating on the keypad and all protective sensors particularly on motion sensors and smoke detectors e The keypad and sensors should be cleaned carefully with a dry soft cloth Do not spray water or any other fluid on the units NOTE It is important that your system is tested periodically to insure proper protection This includes testing the fire alarm portion of your system See TESTING THE SYSTEM and FIRE ALARM SYSTEM sections for the testing procedures 69 Quick Guide To System Functions FUNCTION PROCEDURE COMMENTS Check Zones Press To view faulted zones when is system not ready Display All Press and hold x for 5 seconds Displays all alpha descriptors programmed by Descriptors installer Enter code Press arming key desired AWAY STAY INSTANT MAXIMUM Arm System Arms system in mode selected NOTE After pressing the STAY or INSTANT arming key enter 1 2 or 3 to arm in the desired STAY or INSTANT mode Disarm System Enter code Press OFF 1 Disarms system and silences alarms Enter code Press BYPASS 6 Enter zone numbers to be bypassed use
63. nstallation you were assigned an authority level and a personal four digit security code known only to you and yours The security code must be entered when arming and disarming the system The authority level defines the system functions that you can perform As an additional safety feature other users that do not have a need to know your code can be assigned different security codes and each user can be given a different authority level Users are identified by user numbers which are assigned when assigning a user s security code All codes can be used interchangeably when performing system functions within the limits of each code s authority level a system armed with one user s code can be disarmed by another user s code with the exception of the Operator Level C code See AUTHORITY LEVELS on the following page for details regarding authority levels Important Only users assigned for user numbers 001 050 can perform panel linking functions Duress Code This feature is intended for use if you are forced to disarm or arm the system under threat When used the system will act normally but can silently notify the central station of your situation if that service has been provided The duress code is pre assigned by the installer during installation authority level 6 Important This code is useful only when the system is connected to a central station Quick Arming Note If Quick Arming was programmed by the installer the
64. o Exit User Edit Mode You can exit any of the user edit modes described on the following pages at any time by doing the following 1 Press either or or don t press any key for 10 seconds 2 System returns to normal mode 17 Security Codes amp Authority Levels cont d To Add a User 18 IMPORTANT Temporary users should not be shown how to use any system function they do not need to know e g bypassing protection zones CODE Enter Master or Manager code and press the key Enter the new user s 3 digit User Number 002 250 Enter 4 digit security code for that user The following prompts will appear ADD NEW USER Enter 1 to add a new user code Entering O will 0 NO 1 YES change the existing user s code to the code entered in step 3 See Changing A User s Code section m WN USER NUMBER 003 Enter the authority level 1 6 for this user within ENTER AUTH LEVEL this partition 1 master 2 manager 3 operator A 4 operator B 5 operator C 62duress code GROUP BYPASSING Enter 1 YES to allow this user to perform group 0 NO 1 YES bypasses Enter 0 NO this user will not be able to perform group bypasses ACCESS GROUP If access schedules have been programmed this ENTER 0 8 prompt appears Enter the user s access group number 1 8 if this user should have limited access to the system Enter 0 if no access group should be assigned RF BUTTON This prompt will appear if a 5800 series button 0
65. okes which can be activated anytime by simply pressing the A B C or D keys This feature can be used to make it easy to perform multiple functions at once such as going to another partition to bypass a zone or it can be used to simplify an everyday repeated procedure Refer to the SPEED KEY section for procedures for using this feature Using Schedules Your system may have been programmed with schedules for automatically arming disarming and activating various devices and or performing other system functions at predetermined times Users can modify some of these schedules by manually delaying a dosing time using temporary schedules or by programming special user schedules Refer to the USING SCHEDULES section at the end of this manual for scheduling related procedures Device Timers The system provides up to 20 timers that can be used to control various devices such as lights or appliances These timers are similar in concept to the individual appliance timers that might be purchased at a department store The devices that can be controlled are programmed into the system by the installer Up to 96 of these devices can be programmed Refer to the PROGRAMMING DEVICE TIMERS section for procedures To Access Another Partition GOTO Command Each keypad is assigned a default partition for display purposes and will show only that partition s information But if the user is authorized a keypad in one partition can be used to perf
66. one group Check with your installer for a list of zones assigned to the group s Notes All bypasses are removed when an OFF sequence security code plus OFF is performed Users must be assigned the following attributes to perform the group bypass function e Enabled for group bypassing e Access to the partition s containing the zones being bypassed e Global arming capability To use the Group Bypass feature BYPASS 1 Enter your security code and press 6 then press then enter the group number 01 15 2 BYPASS 007 FRONT In a few moments all the zones in the group UPSTAIRS BEDROOM will be displayed along with the word BYPASS Typical bypass message Wait for these zones to be displayed before arming Arming the system before bypassed zones are displayed eliminates all bypasses 3 DISARMED BYPASS Arm the system as usual when the keypad READY TO ARM displays the ready to arm message Bypassed zones are unprotected and will not cause an alarm when violated while your system is armed 35 Arming Perimeter Only With Entry Delay ON Using the 3 STAY key 36 Use this key when you are staying home but might expect someone to use the entrance door later When armed in STAY mode the system will sound an alarm if a protected door or window is opened but you may otherwise move freely throughout the premises Late arrivals can enter through the entrance door without causing an alarm but they
67. onological order See your Installer for additional information concerning the event log 61 Testing The System To Be Conducted Weekly Using the 5 TEST Key The TEST key puts your system into Test mode which allows each protection point to be checked for proper operation 1 Disarm the system and close all protected windows doors etc READY should be displayed TEST 2 Enter your security code and press the key 3 The external sounder should sound for 3 seconds and then turn off If the sounder does not sound it may be due to dialer communication activity Wait a few minutes and try again If the sounder still does not sound CALL FOR SERVICE IMMEDIATELY 4 The keypad will sound a single beep every 15 seconds as a reminder that the system is in Test mode Each time a protection zone is faulted opened the keypad should beep three times If the sounder does not sound CALL FOR SERVICE IMMEDIATELY Notes e No alarm reports will be sent to the central monitoring station while the system is in Test mode The system will automatically exit the Test mode if there is no activity no doors or windows are opened and closed no motion detectors are activated etc for 30 minutes on the VISTA 128FBP 60 minutes on the VISTA 250FBP The system will beep the keypad s twice every 5 seconds during the last 5 minutes as a warning that it is about to exit the Test mode and return to normal operation Testing Your System
68. orm system functions in another partition by using the GOTO command Note that only those partitions authorized and programmed by the installer can be accessed in this manner To GOTO another partition enter your security code then press followed by the desired partition number 1 8 The keypad will remain in the new partition until directed to go to another partition or until 120 seconds has elapsed with no keypad activity Entering your security code pressing followed by 0 will return the keypad to its original partition System Overview cont d Master Keypad Operation A Master keypad is one on which the status of all 8 partitions is displayed simultaneously A user can get more information about a certain partition by simply entering the desired partition number 1 8 To log on to the Master partition 9 using the GOTO command and to perform any functions at a Master keypad a user must have access to all partitions Self Help Feature Abbreviated user s instructions are built into the system that can be easily viewed on the alpha keypad s message display screen This feature will prove particularly useful if this manual is not conveniently accessible when you need to perform a system procedure with which you are not familiar To view the abbreviated instructions Simply press and hold down the function key of interest until the description starts to appear about 5 seconds and then release it The system
69. ownloader may be viewed at any partition s keypad 45 Panic Keys For Manually Activating Silent And Or Audible Alarms Using Panic Keys Your system may have been programmed to use special key combinations to manually activate panic functions The functions that might be programmed are Silent Emergency Audible Emergency Personal Emergency and Fire See your installer for the function s that may have been programmed for your system Active Panic Functions Your installer should note which function s system BEE your To use a paired key panic function simply press both keys of the assigned pair at the same time tand 995 If your keypad s have lettered keys for 3and 996 panic functions press the designated 46 key and hold down for at least 2 seconds to activate the panic function A silent emergency sends a silent alarm signal to the central station but there will be no audible alarms or visual displays An audible emergency sends an emergency message to the central station if connected and will sound a loud steady alarm at your keypad and at any external sounders that may be connected ALARM plus a zone number would also be displayed A personal emergency alarm sends an emergency message to the central station if connected and will sound at Keypads but not at external Notification Appliance Circuits ALARM plus a zone number would also be displayed A fire alarm sends
70. programmed to automatically transmit alarm or status messages over the phone lines to a central alarm monitoring station NOTE If you have a Symphony Advanced User Interface connected to your system refer to the Symphony User Guide for operating instructions NOTE All references in this manual for number of zones number of user codes number of access cards and the event log capacity use the VISTA 250FBP s features The following table lists the differences between the VISTA 128FBP and the VISTA 250F BP control panels All other features are identical for both panels Feature VISTA 128FBP VISTA 250FBP Number of Zones 128 250 Number of User Codes 150 250 Number of Access Cards 250 500 Event Log Capacity 512 1000 VistaKey Modules 8 15 System Overview cont d A Partitioned System Simply stated a partitioned system shares one physical alarm system among different users each with their own requirements For the most part you as a user need not know about other users and their structure in the system but from time to time you may see display messages which indicate the system is in use by another user Do not be concerned this is normal Refer tothe ACCESSING OTHER PARTITIONS section for additional information Panel Linking Zones Panel Linking networks up to eight VISTA 128F BP VISTA 250F BP control panels enabling a user to control the features of all control panels from a single location
71. ptors indicate that a problem exists with those zone s First determine if the zone s displayed are intact this may include Fire and Waterflow type zones and make them so if they are not If the problem has been corrected key an OFF sequence Code plus OFF to clear the CHECK or TRBL display If the display persists CALL FOR SERVICE IMMEDIATELY CHECK or TRBL display accompanied by a display of 6XX where XX 01 32 indicates a trouble on a supervised relay corresponding relay number 01 32 CHECK or TRBL display accompanied by a display of 8XX where XX 00 30 indicates a trouble on a peripheral device connected to the panel s keypad terminals CHECK or TRBL display accompanied by a display of 9XX where XX 00 99 indicates a system trouble exists dialers Notification Appliance Circuits ground fault etc These zones are as follows 970 Bell 1 Output 975 Dialer 2 971 Bell 2 Output 988 2nd RF Receiver not receiving signals 972 Earth Ground Fault 990 1s RF Receiver not receiving signals 973 J 2 Trigger Output 997 Polling Loop Short 974 Dialer 1 SUPV display accompanied by a display of one or more zone descriptors indicate a problem on fire supervisory zone s This means that the operation of the fire alarm system may be compromised First determine if the zone s displayed are intact and make them so if they are not If the problem has been correc
72. red by users of other partitions in a building that shared partition may be assigned as a common lobby partition for the system An example of this might be in a medical building where there are two doctors and a common entrance area This option employs logic for automatic arming and disarming of the common lobby Partitions may be set to affect and or attempt to arm the common lobby This will affect the way the lobby will react when arming or disarming activity occurs in another partition Partitions that affect the lobby will cause the following to occur a When the first partition that affects the lobby is disarmed the lobby will also be disarmed b The common lobby cannot be armed unless every partition selected to affect the lobby is armed c Arming the last partition that affects the lobby will not automatically attempt to arm the lobby Partitions set to arm the lobby will cause the following to occur a Arming any partition programmed to arm the lobby will automatically attempt to arm the lobby If any faults exist in the lobby partition or another partition that affects the lobby is disarmed the lobby cannot be armed and the message UNABLE TO ARM LOBBY PARTITION will be displayed The following chart summarizes how the common lobby partition will operate Partition Affects Partition Arms Disarms When Attempts to Arm Can Be Armed if Lobby Lobby Partition Disarms When Partition Other Part
73. rm conditions Your system provides four modes of burglary protection STAY AWAY INSTANT and MAXIMUM and even allows you to BYPASS selected zones of protection while leaving the rest of the system armed The system also provides a CHIME mode for alerting users to the opening and closing of doors and windows while the system is disarmed Refer to the other sections of this manual for procedures for using these features The following table lists the four different arming modes and the results of each Features For Each Arming Mode Arming Mode Exit Delay Entry Delay Perimeter Armed AWAY Ves Yes Ys STAY NSTANTE MAXIMUM KThe system provides three different STAY and INSTANT arming modes See ARMING IN THE STAY MODES and ARMING IN THE INSTANT MODES sections for details on these modes When an alarm occurs both the keypad and external sounders will sound and the keypad will display the zone s causing the alarm If your system is connected to a central monitoring station an alarm message will also be sent To stop the alarm sounding simply disarm the system Memory of Alarm When an alarm condition occurs the keypad displays the number s of the zone s that caused the problem and displays the type of alarm ex FIRE ALARM It remains displayed until it is deared by disarming the system see DISARMING THE SYSTEM section System Overview cont d Speed Key Macros The system can store a string of up to 32 keystr
74. s glass partitions glass doors or windows Mechanical tampering masking painting or spraying of any material on the mirrors windows or any part of the optical system can reduce their detection ability Passive Infrared Detectors sense changes in temperature however as the ambient temperature of protected area approaches the temperature range of 90 to 105 F the detection performance can decrease Alarm warning devices such as sirens bells or horns may not alert people or wake up sleepers if they are located on the other side of closed or partly open doors If warning devices sound on a different level of the residence from the bedrooms then they are less likely to waken or alert people inside the bedrooms Even persons who are awake may not hear the warning if the alarm is muffled from a stereo radio air conditioner or other appliance or by passing traffic Finally alarm warning devices however loud may not warn hearing impaired people or waken deep sleepers Telephone lines needed to transmit alarm signals from a premises to a central monitoring station may be out of service or temporarily out of service Telephone lines are also subject to compromise by sophisticated intruders Even if the system responds to the emergency as intended however occupants may have insufficient time to protect themselves from the emergency situation In the case of a monitored alarm system authorities may not respond appropriately This equipment like other
75. s Point 61 Access Point Group Grant Group 62 Access Point Group Grant with Override Group 63 Access Point Group Protect Group 64 Access Point Group Bypass Group 66 Access Point Group Exit Group 67 Access Point Partition Grant Partition 68 Access Point Partition Grant with Override Partition 69 Access Point Protect by Partition Partition 70 Access Point Bypass by Partition Partition 71 Access Point Lock by Partition Partition 72 Access Point Exit by Partition Partition 73 Access Point Trigger On Trigger 74 Access Point Trigger Off Trigger Using 77 Instant Activation Mode cont d Additional Commands Action Code Action Specifier 77 Access Point Group Enable Group 78 Access Point Group Disable Group To enter the Instant Activation Mode Enter your security code then press the key followed by 77 ACTION Enter the code for the desired action The EST action codes are the events that are to take place when either the system exits the 77 Mode or the scheduled time is reached depending on the action selected Press to continue Enter the action specifier This defines what the action will affect relay relay group partition zone list user group The action specifier screen prompt varies depending on the type of action selected Asan example if you selected Auto Bypass as the action the action specifier prompt would be ZONE LIST ARE YOU SURE Enter 1 YES or
76. s the nature and location of all occurrences Keypad display back lighting is programmable to always stay on or to light only when a key is pressed then turn off a few minutes later The keypads also feature a built in sounder that will sound during alarms and troubles It will also beep during certain system functions such as during entry exit delay times during CHIME mode and when depressing keys to perform system functions to acknowledge the key press These sounds can be optionally suppressed in some of your keypads so as not to disturb other users of the system Ask your installer if this has been done The Alpha Keypad 10 Alpha keypads feature a 2 line 32 character alphanumeric Liquid Crystal Display LCD that can display system messages in user friendly English Abbreviated user s instructions can also be displayed see Self Help paragraph in the SYSTEM OVERVIEW section These keypads can also be programmed with custom zone descriptors Functions Of The Keypad LCD DISPLAY SPEAKER kg ARMED lt gt READY lt gt LEDS SUPER lt T gt TROUBLE lt gt FUNCTION KEYS 6160CR 003 V1 IMPORTANT When using the keypad to enter codes and command s sequential key depressions must be made within 3 seconds of one another If 3 seconds elapses without a key depression the entry is aborted and must be repeated from its beginning 11 Functions Of The Keypad cont d A
77. sage disappears when exit delay expires 39 Arming All Protection With Entry Delay OFF Using the 4 MAXIMUM Key A0 Use this key when the premises will be vacant for extended periods of time such as vacations etc or when no one will be moving through protected interior areas When armed in MAXIMUM mode the system will sound an alarm if a protected door or window is opened or if any movement is detected inside the premises You may leave through the entrance door during the exit delay period without causing an alarm but an alarm will be sounded as soon as someone reenters Close all perimeter windows and doors before arming see CHECKING FOR OPEN ZONES section MAXIMUM 1 Enter your security code and press 2 ARMED MAXIMUM The keypad will beep twice and will display the YOU MAY EXIT NOW armed message Note The YOU MAY EXIT NOW portion of the message disappears when exit delay expires Quick Exit Using the In 9 Keys The Quick Exit feature allows you to exit the armed partition without having to disarm and then rearm the partition To Quick Exit the premises 1 Press the key and then press the 9 key 2 Thesystem will sound the exit beeps if enabled and will give you the programmed exit delay time to leave the premises 41 Disarming And Silencing Alarms Using the 1 OFF Key The OFF key is used to disarm the system and to silence alarm and trouble soun
78. splay to view the previous or subsequent fire alarms Fire Drill Test Code 69 64 This test causes Notification Appliance Circuits to be activated in either steady or pulsing manner as programmed in the system for the purpose of conducting a fire drill or a bell test This can only be activated by the installer or a master user from Partition 1 keypads as follows 1 Enter the corresponding security code and press 69 make sure the burglary portion of the system is disarmed Keypads will display FIRE DRILL ACTIVE whilethetest is active 2 Thetest may be stopped by entering any security code and pressing OFF NOTE The system continues to monitor all 24 hour zones fire panic etc while this test is active and will end the test when an alarm condition is detected This test should be conducted at periodic intervals as determined by the local authority having jurisdiction Trouble Conditions Typical Trouble Displays The word CHECK or TRBL on the Keypad s display accompanied by a rapid beeping at the Keypad indicates there is a trouble condition in the system To silence the beeping sound for trouble conditions press any key CHECK or TRBL display accompanied by a display of CALL SERVICE indicates that a problem exists with the system that eliminates some of the protection CALL FOR SERVICE IMMEDIATELY CHECK or TRBL display accompanied by a display of one or more zone descri
79. splays the status of the original partition of the original panel for the keypad Also this mode will end in approximately 120 seconds if no keys are pressed Accessing Other Panels cont d NOTES When performing any of the arming commands if there are faults in any of the partitions none of the partitions will arm These faults must be corrected or bypassed before attempting to arm When performing either a STAY or INSTANT arm command the system always arm in mode 1 see page 36 Arming Perimeter Only for a detailed explanation of the STAY arming modes The user cannot execute another panel linking mode To execute another panel linking mode or to access a different remote panel the user must first exit this mode return to the original control panel Multi Panel View Mode To access the multi panel view mode perform the following steps 1 Enter your security code 8 7 2 Thekeypad displays the following ALLPANEL 12345678 STATUS XXXXXX XX where 12345678 are the panel id and xxxxxxxx is the overall status of each panel Possible status indications include A Armed Away S Armed Stay M Armed Maximum Armed Instant R Ready N Not Ready B Bypassed Ready Alarm T Trouble F Fire Alarm P AC Power Failure L Low System Battery C Comm Fail NOTE See the table that follows for priority of displays Use the following keys to perform a function in the Multi Panel View Mode Press to at
80. stem LED TROUBLE INDICATOR RED Lit when a trouble condition exists in the system SPEAKER Source of audible internal warning and confirmation sounds as well as alarms see Summary of Audible Notifications FUNCTION KEYS These keys can be used for Speedkey macros functions or panic keys Refer to the SPEEDKEY MACROS and PANIC KEYS sections for descriptions of these functions ac Entry Exit Delays General Information 14 Your system has installer programmed time delays known as exit delay and entry delay Whenever you arm your system exit delay gives you time to leave through the designated exit door without setting off an alarm Exit delay begins immediately after entering any arming command and applies to all modes of arming protection If programmed a slow beeping will sound throughout the exit delay period Entry Delay gives you time to disarm the system when you reenter through the designated entrance door But the system must be disarmed before the entry delay period ends or an alarm will occur The keypad will beep during the entry delay period reminding you to disarm the system You can also arm the system with no entry delay at all by using either INSTANT or MAXIMUM arming modes These modes provide greater security while on the premises or while away for extended periods of time See your installer for your delay times Security Codes amp Authority Levels General Information At the time of i
81. ted key an OFF sequence Code plus OFF to dear the SUPV display If the display persists CALL FOR SERVICE IMMEDIATELY 65 Trouble Conditions cont d e A display of COMM FAILURE at the Keypad indicates that a failure has occurred in the telephone communication portion of your system CALL FOR SERVICE IMMEDIATELY e A display of SYSTEM LO BAT accompanied by a once per minute beeping at the Keypad indicates that a low system battery condition exists CALL FOR SERVICE IMMEDIATELY e A display of LO BAT and a zone descriptor accompanied by a once per minute beeping at the Keypad indicates that a low battery condition exists in the wireless transmitter displayed CALL FOR SERVICE IMMEDIATELY e A display of MODEM COMM indicates that the control is on line with the central station s remote computer The control will not operate while on line e A display of HSENS and a zone number indicates a smoke detector with a high sensitivity level which may cause false alarms CALL FOR SERVICE IMMEDIATELY e A display of LSENS and a zone number indicates a smoke detector with a low sensitivity level Detectors with a low sensitivity might not detect a smoke condition CALL FOR SERVICE IMMEDIATELY Power Failure If the message AC LOSS is displayed the Keypad is operating on battery power only If only some lights are out on the premises check circuit breakers and fuses and reset or replace as necessary
82. tempt to disarm all partitions on all panels Press to attempt to arm AWAY all partitions on all panels Press to attempt to arm STAY all partitions on all panels Press 4 to attempt to arm MAXIMUM all partitions on all panels Press to attempt to arm INSTANT all partitions on all panels 29 Accessing Other Panels cont d Press 0 to exit mode After a few seconds the keypad displays the status of the original partition of the original panel for the keypad Also this mode will end in approximately 120 seconds if no keys are pressed NOTES When performing any of the arming commands if there are faults in any of the partitions of a panel the system will not arm that panel but will arm all the other partitions of the other panels When performing either a STAY or INSTANT arm command the system always arms in mode 1 see page 36 Arming Perimeter Only for a detailed explanation of the STAY arming modes The user cannot execute another panel linking mode To execute another panel linking mode or to access a different remote panel the user must first exit this mode return to the original control panel Priority of Displays for Multi Partition and Multi Panel Modes 80 This table shows the priority of displays if more than one of the conditions exists at the same time Priority Description Display 1 FireAlarm F 2 All Other Alarms 3 AC Loss P 4 Comm F ail C 5
83. th this System may not work are as follows Smoke detectors may have been improperly installed and positioned Smoke detectors may not sense fires that start where smoke cannot reach the detectors such as in chimneys in walls or roofs or on the other side of closed doors Smoke detectors also may not sense a fire on another level of a residence or building A second floor detector for example may not sense a first floor or basement fire Moreover smoke detectors have sensing limitations No smoke detector can sense every kind of fire every time In general detectors may not always warn about fires caused by carelessness and safety hazards like smoking in bed violent explosions escaping gas improper storage of flammable materials overloaded electrical circuits children playing with matches or arson Depending upon the nature of the fire and or the locations of the smoke detectors the detector even if it operates as anticipated may not provide sufficient warning to allow all occupants to escape in time to prevent injury or death Passive Infrared Motion Detectors can only detect intrusion within the designed ranges as diagrammed in their installation manual Passive Infrared Detectors do not provide volumetric area protection They do create multiple beams of protection and intrusion can only be detected in unobstructed areas covered by those beams They cannot detect motion or intrusion that takes place behind walls ceilings floors closed door
84. their own or other users codes Quick Guide To System Functions cont d FUNCTION Delete a User PROCEDURE Enter master manager code Press CODE 8 Enter user no to be deleted Enter master manager code Press 1 Yes at prompt COMMENTS Master amp Manager level users can delete users A user can only be deleted by a user with higher authority level Control Output Device Enter security code Press Enter 71 or 72 Activate output device as programmed Enter security code Press Enter 70 Activate output device manually Enter security code Press Enter 77 Activate output device or system event instantly Randomize Output Device Enter security code Press Enter 41 Randomize output devices set for random schedules Enter security code Press Enter 42 Randomize output devices set for random schedules with activation times between 6 PM and 5 AM Enter the sequence used to activate randomization De activate randomization Panel Linking Enter security code 002 050 Press Enter 86 Activate single panel single partition mode Enter security code 002 050 Press Enter 85 Exit single panel single partition mode Enter security code 002 050 Press Enter 88 Activate multi partition multi panel mode Enter security code 002 050 Press Enter 87 Activate multi panel view mode Enter 0 Exit mu
85. timer to turn lights on one day and using another timer to turn them off on another day Select the days on which the device is to be activated by entering 1 7 Monday 1 An X will appear under that day indicating the output for that day is active Entering a day s number again will deactivate that day Pressing O will turn all days on off The outputs will only be in effect for the days that have the letter x underneath them As the week progresses the days are reset to the inactive state unless the permanent option is selected next screen prompt When completed press to continue Answering 1 YES means the system executes this timer continuously Answering 0 NO means the system executes each day s output only once 55 Programming Device Timers cont d Randomize Output Device Times 56 Devices in your system may be set for a random schedule whereby they will turn on and off at different times each day This is useful when going on vacation and you desire the turning on and off of the lights to the give the appearance of someone being home Your installer sets these devices for a random schedule You can initiate a random schedule by either of the following methods 1 Enter your security code and pressl followed by 41 This will randomize up to 30 minutes the activation time of all devices programmed for randomization assigned to the partition the sequence is entered in Enter the seguenc
86. to set each burglary zone for Auto stay All zones enabled for auto stay except for perimeter and day night types of zones has exit delay time when the partition is armed Check with your installer for the zones assigned for Auto STAY NOTE e Auto STAY applies to all four arming modes AWAY STAY INSTANT and MAXIMUM e Arming the partition AWAY via an RF transmitter overrides the Auto stay feature partition will not bypass zones programmed for auto stay lt 37 Arming Perimeter Only With Entry Delay OFF Using the 7 INSTANT Key 38 Important If you are using a Symphony Advanced User Interface NIGHT mode is the same as INSTANT Use this key when you are staying home and do not expect anyone to use the entrance door When armed in INSTANT mode the system will sound an alarm if a protected door or window is opened but you may otherwise move freely throughout the premises The alarm will also sound immediately if anyone opens the entrance door The system provides three INSTANT modes INSTANT mode 1 2 and 3 INSTANT modes 1 and 2 when activated automatically bypass specific zones assigned by your installer to each of the INSTANT modes INSTANT mode 3 when activated automatically bypasses all zones assigned to INSTANT modes 1 AND 2 Check with your installer for a list of the zones that are bypassed during each INSTANT mode Close all perimeter windows and doors before arming see CHECKING FOR OPEN ZONES se
87. ur authority level and system capabilities 1 Enter your code X 2 Thekeypad will display the partition s that you are authorized to operate and your user number and authority level in each partition Security Codes amp Authority Levels cont d General Rules on Authority Levels and Changes e A user may not delete or change the user code of the SAME or HIGHER authority than which heis assigned e A user may only ADD users to a LOWER authority level e A user may assign access codes only to those partitions to which the user adding the code has access ex a user with access to only partition 1 cannot assign codes in partition 2 e The only way to assign a user s authority level is by using the Add A User procedure To change a user s authority level that user must first be deleted then added again e A user can only be DELETED or CHANGED from within the partition he is assigned e User numbers must be entered as 3 digit entries Single digit user numbers must be preceded by a 00 example 003 004 etc Security codes are entered as 4 digit numbers e Before assigning a security code be sure it does not conflict with any DURESS code Note When adding changing or deleting users all other alpha keypads in that partition will display User Edit Mode Please Stand By and key depressions except Panic at those keypads will be ignored Panic key depressions will cause an alarm and terminate user entry T
88. y General Arming Disarming Using The Keyswitch Your system may be equipped with a keyswitch for use when arming and disarming a partition A red and green light on the keyswitch plate indicate the status of your system as follows Green Light Red Light Lit Steady Slow Flashing Rapid Flashing Lights when the system is disarmed and ready to be armed no open zones If the system is disarmed and the green light is off it indicates the system is not ready one or more zones are open Lights when system is armed or memory of alarm exists Partition is armed in AWAY mode Partition is armed in STAY mode Memory of alarm indicating an alarm has occurred To arm in the AWAY mode turn the key to the right for 1 second and release Keypads will beep twice and the red light will stay on steady To arm in the STAY mode turn the key to the right and hold for longer than 10 seconds then release Keypads will beep three times and the red light will flash slowly To disarm the partition turn the key ge gt to the right and release If an alarm has occurred the red light will be flashing rapidly memory of alarm NOTE Your system may be programmed to use the keyswitch to silence fire alarms without affecting the status of the burglary portion of the system Check with your installer to see if this feature has been enabled cdi Chime Mode Using the 9 Key Your system can be s

Honeywell Vista-250FBP User Manual

Contents

Download Pdf Manuals

Related Search

Related Contents