Z-lOl SERIES USER`S GUIDE
Contents
1. straps that were removed earlier with the screws at positions AE and AF Return the latching slides to their normal position and replace the two screws AA and AB Make sure that the slides move freely then slide them about 1 4 towards the rear of the Computer Pictorial 14 Page 15 Assembly Referto Pictorial 15 Replace the top case by bringing it straight down into its position and slide the latches all the way to the front if they do not snap into place This completes the assembly of the all in one model Return to the acces sory Installation Manual and perform any necessary tests Pictorial 15 DRIVE SUBASSEMBL BEVEL Pictor INSET 2 TRIANGLE 08 MARKED EDGE pi SSD owe oN SFT SNS AEN AN NM V e AS ANA VY A Ant Pictorial 16 DRIVE SUBASSEMBL Pt 2 we d 2 A SSSSS SS SS Soo SS _ e SSO Press Poo ui N NN ANN MANNY ES Page 16 Assembly LOW PROFILE MODELS Refer to Pictorial 16 fold out from this Page and rest the drive subassembly about 2 inches in front of its normal position on the base Refertoinset 1 and plug the power cables into each disk drive Refer to inset 2 note the slot in the drive connector strip Position the small2. drive latch is closed FLOPPY DISK LED DISKETTE DRIVE LATCH DISK ACCESS ege INDICATOR Pictorial 2 Disk drive components Page 3 Disassembly The following disassembly instructions apply to the all in one model of the Z 101 with built in display If you have the low profile model proceed to Disassembly Low Profile Models on Page 6 NOTE The disk drives shown in the illustrations in this Manual are typical of the ones being supplied in the Z 101 series Computers However the location of the flat cable connector and power connector may vary slightly from the locations shown ALL IN ONE MODELS WARNING When the line cord is connected to an AC outlet hazardous voltages can be present inside your Computer Unplug the line cord from the AC outlet Refer to Pictorial 3 Using a small flat blade screwdriver move the metal slides all the way to the front and then 1 4 to the back as shown Carefully lift the top case straight up and set it to one side TOP CASE Pictorial 3 Page 4 Disassembly Refer to Pictorial 4 and remove the back screws at positions AA and AB that hold each latching slide Pivot each latching slide out as shown Remove the five screws at positions AC AD AE AF and AG Note the position of the ground straps at AE and AF if present Carefully lift the drive video subassembly up and to the front of the Computer about 4 to 5 inches and set i
3. triangle or marked edge of the flat cable toward this end of the connector strip Plug the flat cable from the Z 207 board onto the disk drives as shown Movethedrive subassembly to its normal position Page 17 Assembly Referto Pictorial 17 and install and tighten the four screws at posi tions AA AB AC and AD Install and tighten the two locking pins at AE and AF 66 E emm Pictorial 17 Page 18 Assembly Refer to Pictorial 18 Replace the top case by bringing it straight down into its position Push the latches all the way forward if they do not snap into place This completes the assembly of the low profile model Return to the acces sory Installation Manual and perform any necessary tests Pictorial 18 PUSH FORWARD 2
4. SING ISSO EN NN E Se SS lt Pictorial 13 599 12 Assembly Refer to Pictorial 12 for the steps below Positionthekeyboardonthe base as shown Replace the keyboard and base cover and install and tighten the two screws you removed earlier at positions BA and BB Make sure the keyboard is centered so that no keys rub on the sides of the keyboard opening This could cause the keys to stick Low profile models only Install and tighten the two locking pins at positions BC and BD Low profile assembly instructions continue on Page 16 2 KEYBOARD AND BASE COVER J Pictorial 12 Page 13 Assembly ALL IN ONE MODELS Refer to Pictorial 13 fold out from Page 10 and rest the drive video subassembly 4 to 5 inches in front of its normal position on the base Plug the signal power cable into the video board Refer to inset 1 and plug the power cables into each disk drive Move the drive video subassembly to its normal position Refer to inset 2 and note the slot in the drive connector strip Position the small triangle or marked edge of the flat cable toward this end of the connector strip Plug the flat cable from the Z 207 board onto the disk drives as shown Page 14 Assembly Refer to Pictorial 14 and install and tighten the five screws at posi tions AC AD AE AF and AG Be sure you replace the ground
5. Z 101 series computers NOTE The disk drives shown in this manual are typical of the type sup plied in the Z 101 series computers The drives in your unit may be differ ent iv Contents 6 0 9 9 9 9 8 9 9 9 9 9 eee 9 9 9 9 9 9 9 8 9 8 9 8 6 8 9 9 8 9 ee ee eo Page 1 Disk Drives Look at the disk drives They are storage devices designed to transfer information into and out of your Computer s memory Refer to Pictorial 1A for the all in one model and Pictorial 1B for the low profile model e Disk Drive Positions One or two disk drives are included with your Desktop Computer For dual drive systems on the all in one model the top disk drive is referred to as Drive A and the bottom one is Drive B On the low profile model the left disk drive is Drive A and the right one is Drive B f your Desktop Computer has only one disk drive it will be known as Drive A regardless of its position in either the low profile or all in one model The Drive names A and B are arbitrary with the Disk Operating System The systems supplied with your Desktop Computer use the names illus trated here Other operating systems may refer to the drives by other means Consult the documentation supplied with those systems for the names of the drives Drive A will be the lowest named drive Drive B the next Pictorial 1A Pictorial 1B All in one model Low profile model Page 2 Disk Drives Refer to Pictorial 2 for
6. data systems THE QUALITY GOES IN BEFORE THE NAME GOES ON DESKTOP COMPUTER SYSTEMS Z 101 SERIES USER S GUIDE Z 101 Series User s Guide data 4 systems Copyright 1983 Zenith Data Systems Corporation all rights reserved Printed in the United States of America RESTRICTED RIGHTS LEGEND Use duplication or disclosure by the Government is subject to restrictions as set forth in paragraph b 3 B of the Rights in Technical Data and Computer Software clause in DAR 7 104 9 a Contractor Manufacturer is Zenith Data Sys tems Corporation of Hilltop Road St Joseph Michigan 49085 Zenith Data Systems Corporation Saint Joseph Michigan 49085 Preface This User s Guide is a supplement to the Z 100 series manuals you re ceived with your Z 101 series computer This User s Guide is divided into three parts e Disk Drives This information replaces the Disk Drives information on pages 1 13 and 1 14 of the Z 100 User s Manual e Disassembly This information replaces the disassembly informa tion in the Installation Manual for any accessories you may have or may purchase in the future e Assembly This information replaces the assembly information in the Installation Manual for any accessories you may have or may purchase in the future Except as noted above all the information in the Z 100 User s Manual and other Z 100 series manuals applies to the
7. llowing steps Pictorial 7 Page 8 Disassembly sl Refer to Pictorial 8 and carefully unplug the flat cable from the disk drives as shown Carefully unplug the power cables from each disk drive Remove the drive subassembly and set it to one side DRIVE SUBASSEMBL Pictorial 8 Page 9 Disassembly FINAL DISASSEMBLY Both Models Referto Pictorial 9 and unscrew the two screws at positions BA and BB in the keyboard and base cover Low profile models only Remove the two locking pins at positions BC and BD Remove the keyboard and base cover by lifting it up and to the back in order to clear the covers controls and connectors on the back panel Set it to one side KEYBOARD AND ED BASE COVER ws Pictorial 9 w 5 5 a Page 10 Disassembly Refer to Pictorial 10 and carefully lift the keyboard up and position it to the front of the Computer Carefully remove the three screws at positions BE BF and BG in the Video circuit board Return to the accessory Installation Manual and perform the instal lation steps for the accessory Pictorial 10 Page 11 Assembly BOTH MODELS Refer to Pictorial 11 and reposition the video circuit board as shown Install and tighten the three screws you removed earlier at positions BE BF and BG Pictorial 11 DRIVE VIDEO SUBASSEMBLY a Pa da N H Z Fa CANS
8. t back down gently Rest the subassembly here for the following steps 10 11 n 1 1 5 SS ES Pictorial 4 Page 5 Disassembly Refer to Pictorial 5 fold out from Page 9 and carefully unplug the signal power cable from the video circuit board Carefully unplug the flat cable from the disk drives as shown in the Pictorial Carefully unplug the power cables from each disk drive Remove the drive video subassembly and set it to one side Proceed to Final Disassembly Both Models on Page 9 Page 6 Disassembly LOW PROFILE MODELS WARNING When the line cord is connected to an AC outlet hazardous voltages can be present inside your Computer Unplugthelinecordfromthe AC outlet Refer to Pictorial 6 Pull the metal slides all the way to the back and then push them 1 4 to the front as shown Carefully lift the top case straight up and set it to one side PULL METAL SLIDES ALL THE WAY BACK THEN PUSH FORWARD 1 4 Pictorial 6 Page 7 Disassembly Refer to Pictorial 7 and remove the four screws at positions AA AB AC and AD Remove the two locking pins at AE and AF Carefully lift the drive subassembly up and to the front of the Com puter about 2 inches and set it back down gently Rest the subas sembly here for the fo
9. the following Discussion Pictorial 2 shows a typical disk drive The disk drives in your unit may look slightly different Diskette Load Slot Insert diskettes in this slot with the label up and toward you as shown in the Pictorial If the diskette is not oriented as shown the unit will not operate properly and you may damage the diskette and or the disk drive If the diskette meets resistance while you are inserting it into the drive check to make sure that there is not a diskette already in the drive It should slide smoothly into the drive Disk Drive Latch This latch secures the diskette in the disk drive Closing the latch engages the drive hub into the diskette and brings the read write heads into contact with the disk surface If the latch shuts with difficulty remove the diskette inspect the large center hole for damage check for proper diskette orientation see the previ ous description and try again NOTE Many types of disk drives are equipped with a locking system that prevents the latch from being closed if there is no diskette in serted in the drive This is to prevent possible damage to the read write heads Be sure there is a diskette inserted in the disk drive before trying to close the latch LED Disk Access Indicator This LED indicates that the Computer is attempting to read from or write to the diskette The read write operation will be successful only if the diskette is inserted properly and the disk
Download Pdf Manuals
Related Search