User manual for BeSafe iZi Kid X1 i-size-GB
Contents
1. Install the front brace by sliding the two pins into the oval tube under the front side of the seat Move the front brace inwards with the ratchet The ratchet is used to adjust the front brace in both directions Slide the switch on the ratchet up or down to change direction 23 Pull both ISOfix connectors as far out as possible by pushing the grey buttons on top of the base 24 Remove the caps from the ISOfix connectors by pressing down the ISOfix release buttons 25 Click the installation clips on the ISOfix connectors 26 Fold down the floor support before you install the seat in your vehicle 27 Place the seat sideways into the car with the front brace towards you Turn the seat into the right position with the front brace against the back rest Click the ISOfix connectors in the ISOfix anchorage of the vehicle 28 Remove the installation clips Make sure that all indicators on both sides are green 29 Push the seat towards the backrest of vehicle seat till the frontbrace touches the backrest the isofix arms slide in and will click into a new position 30 Move the front brace outwards with the ratchet Continue tightening until the brace is pressed well into the back rest of the vehicle seat 31 Remove the cap around the floor support An alarm sound will start and stop when the seat is installed correctly with the floor 1 22 23 24 25 26 27 28 29 s2. areas where the child seat might touch the interior We recommend using a BeSafe protection cover in these places to avoid cuts marks or discolouration on the interior of the vehicle especially in vehicles with leather or wooden interior Guarantee Point of sale information All BeSafe products are carefully designed manufactured Notice for REARFACING installation and tested All of our BeSafe child seats are tested This is a universal i Size Child Restraint System periodically out of our continuous production in our test It is approved to regulation No 129 series of laboratory Furthermore they are tested by independent amendments for general use in vehicle seat test institutes positions marked with the i Size logo The seat is also suitable for fixing into vehicle seat positions approved as ISOfix positions as detailed in the vehicle handbook listed in the separate car list Seat positions Should this product prove faulty within 24 months of purchase due to materials or manufacturing fault except covers and harness straps please return it to the original place of purchase in other vehicles may also be suitable to accept this child The guarantee is only valid when you use your seat restraint If in doubt consult either the child restraint appropriately and with care Please contact your retailer manufacturer or the retailer For updated car list see they will decide if the seat will be returned to the www besafe c
3. Z lt 5 ap Zu aL Da 1 6 9 1 e R Stature height USER MANUAL Thank you for choosing BeSafe iZi Kid i Size BeSafe has developed this seat with great care to protect your child during the first phase of his or her life o It is important that you read this user manual BEFORE installing your seat Incorrect installation could endanger your child Contents Vital information 8 Preparing to install 10 Rearfacing ISOfix installation 10 Positioning the child 14 Sleeping position 14 Removing and refitting the cover 15 Cleaning instructions 15 Warning potential misuse 16 Important advice 16 Guarantee 18 Point of sale information 19 AP Vital information It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG iZi Kid i Size can only be installed rearfacing with the ISOfix anchorage in a car equipped with ISOfix anchorage points iZi Kid i Size is approved for children with a stature height from 61 to 105 cm rearfacing with a max weight up to 18 kg Read the car list to find out whether your car model is approved to use the seat The harness straps must always be locked when the child is in the seat The harness straps must be tightened without slack and not twisted The seat cover contains magnets in the areas with the orange indications Magnets can influence electronic equipment such as pacemakers The floor support must always be used Make sure
4. brace Cap ISOfix connector 2x Switch for ISOfix connectors 2x Floor support Height adjuster floor support Floor support height indicator Release handle head rest Floor support position indicator ISOfix car anchorage 2x ISOfix insertion clips 2x bottom side ISOfix connectors 2X ISOfix indicators 2x ISOfix release button 2x Oooo ANN sad m Am DAWN DN 1 N N O O Rearward facing ISOfix installation It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG 1 The seat can only be installed rearfacing in vehicles equipped with ISOfix anchorage points 2 When mounting in the back seat of the vehicle push the front seat of the vehicle forward as much as possible 3 When mounting in the front seat of the vehicle adjust the back rest into an upright position 4 Positioned in the front seat of the vehicle you should position the seat against the dashboard 12 13 14 17 18 19 20 21 If it s not possible to position the seat against the dashboard position the seat as far as possible from the dashboard Find the ISOfix anchorage points in the vehicle 21 If your vehicle is not equipped with ISOfix insertion clips insert these to make installation easier 22 You can find the ISOfix insertion clips under the base of the seat or delivered separately with the seat
5. ed when the child is in the seat Sleeping position The seat has 3 positions By pulling the recline lever upwards the seat can be adjusted into another position 46 Removing and refitting the cover Removing the cover Do take care when you remove the cover as fitting the cover is done in reverse Start taking off the lower seat part 47 The cover of the head rest can be taken off separately by disconnecting the hooks at the back and pulling off the fabric towards the front Refit the cover Pull the head rest in the highest position Replace the head rest cover and reconnect the hooks at the back side Pull the harness straps through the holes Connect the loose lower part of the head rest fabric with the plastic part below the head rest Refit the top part and then the shoulder parts Refit the seat part and bring the seat cover under the rear parts of the sidewalls Cleaning instructions The cover of the seat must be washed according to the instructions on the inside of the cover DO NOT use any aggressive cleaning products these may harm the construction material of the seat I Warning potential misuse It is NOT ALLOWED to mount the seat in a front passenger seat WITH AN ACTIVATED AIRBAG DO NOT use the seat without floor support The floor support must always be used Make sure that the floor support is fully pushed down DO NOT use the seat without tightening the front brace Make s
6. nnectors into the base 37 Pull the seat back towards the front Turn the seat so you can easily remove the seat Remove the insertion clips from the vehicle Place them under the base of the child seat To remove the front brace from the metal tube move the front brace outwards with the rachet until the lock button of the front brace appears Push the lock button down with a small screw driver while pulling the front brace out 38 Positioning the child 1 Position of the shoulder straps Check that the shoulder strap slots are level with your child s shoulders Too high 39 Correct 40 2 The height of the shoulder straps and the head rest can be adjusted by pulling the release handle upwards at the back of the head rest and pulling the head rest up or down while keeping the head rest upright 41 3 Pull the shoulder straps up while pressing the button of the central adjuster 42 4 Open the harness buckle 5 Position the shoulder straps over the orange marking at sides of the seat to keep the harness open while you position the child 43 6 When the child is positioned place the shoulder straps over the child s shoulders and close the buckle CLICK 44 Pull the harness strap through the central adjuster in the direction of the arrow straight up forwards Continue pulling until the harness is a comfortable but firm fit 45 g Make sure that the harness straps are always locked and tighten
7. om manufacturer for repair Replacement or return cannot be claimed The guarantee does not get extended Next car seat through repair When the child has grown out of the seat BeSafe recommends The guarantee expires when there is no receipt when to use the next seat for children above 18 kg up to a height of defects are caused by incorrect and improper use when at least 135 cm defects are caused by abuse misuse or negligence HTS BeSafe as N 3535 Kr deren Norway www besafe com
8. that the floor support is fully pushed down When installed with ISOfix Make sure the indicators are green before you drive We recommend that this seat is used only for children who can sit upright so not younger than 6 months For children under 1 year and or under 10 kg weight we recommend that the most reclined sitting position and the body hugger and baby cushion extra available accessory are used Remove the baby cushion extra available accessory when the child is older than 1 year Remove the body hugger when the child is older than 2 years When the child weighs over 18 kg or the shoulder height grows above the highest position of the shoulder straps the child must change to a seat suitable for children with a weight above 18 kg After an accident the seat must be replaced Although it may look undamaged if you were to have another accident the seat may not be able to protect your child as well as it should Prevent the seat from becoming trapped or weighed down by luggage seats and or slamming doors Before every use make sure the harness is not damaged or twisted Make sure you can fit no more than one finger between the harness and your baby 1 cm If in doubt consult either the car seat manufacturer or the retailer Preparing to install Crucial parts Adjustable head rest Shoulder straps 2x Harness buckle Body hugger Front brace Central adjuster Reclining lever Ratchet for front
9. upport in contact with the floor of the vehicle seat 32 Adjust the floor support so it is in contact with the floor of the vehicle 33 The height indicator of the floor support shows green when the floor support is in contact with the floor 34 The alarm sound stops when the floor support shows green and is in contact with the floor Positioned in the back seat of the vehicle you should if possible push the front seat of the vehicle backwards so that it is in contact with the child seat If it is not possible to obtain contact with the child seat push the back rest of the front seat of the vehicle forward as far as possible When the child has a stature height of 87 cm or more use the seat in the upright position When you want to enlarge the available space for your child keep the isofix arms totally slided out without pushing the seat towards the backrest and tension the frontbrace outwards with the rachet Make sure the floor support is fully pushed down in contact with the floor of the vehicle and locked Make sure that all indicators on both sides are green Removing the seat N If the seat is installed in the back seat of the vehicle push the front seat of the vehicle forward as much as possible Move the front brace inwards with the ratchet 35 Release the ISOfix connectors by pressing the release mechanism on the ISOfix connectors 36 Push the switch on each side and push the ISOfix co
10. ure the indicators are green before you drive A Important advice DO NOT attempt to dismantle modify or add any part to the seat Warranty will be void if non original parts or accessories are used DO NOT use anything such as a cushion to raise the child seat off the passenger seat of the vehicle In an accident the seat will not be able to protect your child in the right way Never leave your child unattended in the seat Make sure all passengers are informed about how to release your child in case of emergency An empty child seat should always be fastened in the vehicle Make sure luggage or other objects are properly secured Unsecured luggage may cause severe injuries to children and adults in case of accidents Never use the seat without the cover The cover is a safety feature and may only be replaced by an original BeSafe cover Under the cover we use EPS foam Do not push or pull too hard against the foam as you may damage the foam Do not use any aggressive cleaning products these may harm the construction material of the seat BeSafe advises that child seats should not be bought or sold second hand KEEP this user manual for later use with the seat DO NOT use at home It has not been designed for home use and can only be used in a vehicle When installed with ISOfix Check the manufacturer s vehicle handbook Practical advice When the child seat is mounted in the car check all the
Download Pdf Manuals
Related Search