URCOM User`s Manual
Contents
1. last read encodes the last 2 bits and sets the FULL flag The data is encoded by reading a specific register as determined by the data bits The proper register is determined by ADDING the VALUE of the data bits to the base address of the URCOM as follows Ist READ address URCOM ADDRESS the value of D0 2 This will access one of URCOM s registers between 0 and 7 2nd READ address URCOM_ADDRESS the value of D3 5 This will access one of URCOM s registers between 0 and 7 3rd READ address URCOM ADDRESS the value of D6 7 8 This will access one of URCOM s registers between 8 and 11 The extra 8 added to the last read tells URCOM that these are the final two bits and the end of this TRANSMISSION When URCOM detects a read to one of these four bytes 8 11 it will set the TRANSMIT FULL flag Once UniROM sees the TRANSMIT BUFFER FULL flag it will transfer the byte to the selected HOST port URCOM will clear the FULL flag as soon as this byte is read by UniROM URCOM USER S MANUAL 5 Code Examples The following C code fragments should make this concept more clear include lt stdio h gt assume we configured the URCOM address to 0xF000 in the UniROM setup define URCOM BASE unsigned char 0xF000 prototypes void urcom_init void unsigned char urcom_getch void void urcom_putch unsigned char c global pointers static unsigned char tx_base static unsigned char rx_buff s2. OM into its socket with firm even pressure Visually inspect the installation to verify that the connectors are completely seated and that NO PINS were bent When properly inserted the pins plastic body should touch the sockets plastic body and the URCOM components should almost touch the UniROM base board URCOM USER S MANUAL 2 Upgrade the firmware if needed If you are upgrading your firmware use a PLCC removal tool to remove the old ROM at US This is a socketed 32 pin PLCC device The socket can be damaged if a screw driver or other substitute is used in place of a PLCC removal tool Rotate the replacement Firmware ROM so that its notched corner aligns with the socket s notched corner The notch is used to ensure that the ROM is not inserted backwards but one could forced the part in backwards with enough effort Square the ROM in the socket so that the socket s small ribs fit BETWEEN the ROM s pins When the part is aligned properly insert it into the socket with firm even pressure When properly seated the top of the ROM should be flush with or slightly below the top of the socket Re install the memory board s Re insert the memory boards into the memory expansion sockets being careful to orient the board such that the target connector is pointing towards the rear INSERTING THE MEMORY BOARD BACKWARDS WILL RESULT IN DAMAGE TO THE BOARD WHEN POWER IS APPLIED Seat the board s firmly into the conne
3. URCOM User s Manual V1 1 TechTools PO BOX 462101 Garland TX 75046 972 272 9392 FAX 972 494 5814 www tech tools com support tech tools com Table of Contents INTRODUCTION INSTALLATION Verify UniROM s Firmware Version PLEASE observe standard anti static procedures Remove UniROM s case Place UniROM s circuit board assembly on an anti static mat or other flat grounded conductive surface Remove UniROM s rear end plate Remove UniROM s memory board s Install URCOM board Upgrade the firmware if needed Re install the memory board s Re install the end plate Re install UniROM in its case URCOM CONFIGURATION Fe ne RR w WW WwW NNN e SPECIAL NOTES for DUAL 16bit UniROMs COMMUNICATING THROUGH URCOM RECEIVE o o TRANSMIT Code Examples URCOM REGISTER DEFINITIONS CONCLUSION aA a a AA Aa A Q INTRODUCTION URCOM is a very unique UniROM option It provides a bi directional communications path between the TARGET and the HOST PC without using TARGET WRITE cycles This capability allows a target to communicate through shared memory even if it is not capable of writing to the memory socket being emulated by UniROM INSTALLATION URCOM is an expansion option for UniROM It is plugged into a set of connectors on UniROM s base board The following steps outline the installation procedure Verify UniROM s Firmware Version Before beginning the installation v
4. ctors You are inserting 80 pins into full contact sockets so this will take considerable force Re install the end plate Slip the end plate over the target connectors Re install UniROM in its case Place the circuit board assembly back on the case BOTTOM placing both end plates into the molded grooves Place the case TOP into place Verify that the case top seats fully and that the end plates are seated into the molded groves in the TOP and BOTTOM pieces Turn UniROM over and re insert the screws URCOM USER S MANUAL 3 URCOM CONFIGURATION URCOM is configured through the SETUP HARDWARE UART menu Use URTERM to set URCOM s address and optionally enable its interrupt The address can be any 16 byte aligned address within the memory space emulated by UniROM A 16 byte aligned address will always end in a 0 in HEX notation Oxfff0 0x3560 Oxd0000 Use SETUP CONSOLE menu to connect a HOST port to the URCOM device during console operations A virtual connection will now be made between the HOST port and the URCOM option board whenever CONSOLE is selected from the main menu or whenever URLOAD is run with CONSOLE ON specified in its INI file SPECIAL NOTES for DUAL 16bit UniROMs IF you are using a 16bit UniROM in TWO INDEPENDENT DEVICES organization URCOM MUST be mapped into the lower emulation board If you are using a 16bit UniROM in INTERLEAVED organization the URCOM board will occ
5. erify that your current FIRMWARE revision is 1 52 or newer To verify your Firmware revision follow these steps Connect to UniROM as usual with URTerm exe Reset UniROM Press the ENTER key until UniROM responds UniROM will display a sign on message and its firmware revision If your firmware is older than 1 52 and your order did not include a firmware upgrade call out tech support department for additional information PLEASE observe standard anti static procedures UniROM and URCOM are electronic devices that require basic anti static precautions while handling They are no more OR LESS susceptible to damage due to electrostatic discharge than other electronic assemblies and should be handled only at an anti static equipped work station If your facilities are not equipped to provide these basic precautions we would be happy to do the installation for you at no charge Call our Tech support department for an RMA number and return instructions Remove UniROM s case Remove the screws from the bottom of UniROM with a 1 Phillips screwdriver Remove the case TOP and BOTTOM Place UniROM s circuit board assembly on an anti static mat or other flat grounded conductive surface UniROM is an electronic device that can be damaged by static electricity It should be handled with the appropriate precautions URCOM USER S MANUAL 1 Remove UniROM s rear end plate The rear end plate is held in place by the case top and bottom
6. no mounting hardware is used To remove the end plate move all cable latches to their latched positions and slide the end plate off Remove UniROM s memory board s UniROM has one or two memory architecture boards plugged into a base board The memory board s must be removed to gain access to the URCOM expansion connectors If your UniROM has two memory boards there is no need to separate them from each other They may be removed as single unit The memory architecture board connectors have a very firm grip You will need to work loose all four corners before the board s can be removed This can take some time but resist the urge to pry the boards apart This procedure could very easily damage other components or board traces BE VERY CAREFUL NOT TO DAMAGE THE BASE BOARD OR MEMORY BOARDS Our warranty WILL NOT cover such damages If you are uncomfortable with this procedure we would be happy to do the installation for you at NO CHARGE Simply call out Tech support department for an RMA number and return instructions Install URCOM board Insert URCOM into the expansion connectors found directly below the memory board s NOTE that URCOM is installed with its components facing down Check carefully that all pins are aligned properly with the sockets It will take considerable force to install URCOM so verify that the UniROM baseboard has been placed on a firm flat surface NOT on the case bottom Press URC
7. sees the underlying SRAM instead of URCOM registers CONCLUSION We designed URCOM so that it can be easily integrated in any target with minimal work This option allows one to add full bi directional communications to any target without hardware modifications and with minimal software modifications If you would like to share your own URCOM routines for your specific target CPU with our other customers feel free to upload them to our BBS We would also welcome any comments on your particular applications for this device If you have any problems comments or suggestions please feel free to contact us through VOICE FAX or our BBS TechTools PO BOX 462101 Garland TX 75046 972 272 9392 FAX 494 5814 email support tech tools com URCOM USER S MANUAL 8
8. tatic unsigned char status A simple example to demonstrate how a TARGET communications through URCOM without using WRITE cycles void main void unsigned char c urcom_init0 initialize URCOM while 1 c urcom_getch wait for a byte from the HOST urcom_putch c ECHO it back to the HOST void urcom_init void unsigned char dummy initialize pointers tx_base URCOM_BASE rx_buff URCOM_BASE 0x0C status URCOM BASE 0x0D clear any pending RX interrupts dummy rx_buff URCOM USER S MANUAL 6 unsigned char urcom_getch void wait for character to appear while status amp 0x02 return rx_buff void urcom_putch unsigned char c unsigned char dummy wait for TX buffer to empty while status amp 0x01 send data dummy tx_base c amp 0x07 encode d0 d2 c c gt gt 3 dummy tx_base c amp 0x07 encode d3 d5 c c gt gt 3 dummy tx_base c amp 0x03 8 encode d6 d7 and set FLAG URCOM USER S MANUAL 7 URCOM REGISTER DEFINITIONS Offset from BASE TARGET READ Encode D0 2 1st RD D3 5 2nd RD Encode D6 7 amp set TXFULL ne O pS a STATUS REGISTER DEFINITION TARGET SIDE DO TX FULL FLAG 1 gt last byte not received by HOST yet D1 RX FULL FLAG 1 gt Receive data available D2 7 Unknown When the HOST DISABLES URCOM the status register is cleared the target
9. upy 32 bytes of memory URCOM USER S MANUAL 4 COMMUNICATING THROUGH URCOM This section describes how the target uses URCOM to send and receive data Each operation is described below RECEIVE The target receives data from URCOM very much like it would from a standard UART A STATUS register holds a RECEIVE FULL flag that indicates when the RECEIVE BUFFER holds a byte of data When the target reads the data from the RECEIVE BUFFER URCOM automatically clears the flag IF the URCOM interrupts were enabled in the SETUP HARDWARE UART menu UniROM will generate an interrupt each time it places data in the RECEIVE BUFFER The interrupt is cleared when the target reads the status register TRANSMIT This is where URCOM differs from a typical memory mapped UART The target TRANSMITS by doing a sequence of 3 reads from specific registers within URCOM Special read sequences are interpreted by URCOM as a request to send specific data The data to be sent is decoded from the specific registers accessed during the read sequence When URCOM detects one of these sequences it places the decoded data into the TRANSMIT BUFFER and sets the TRANSMIT BUFFER FULL flag When UniROM transfers this data to a HOST port the TRANSMIT FULL flag is cleared The target determines which registers to read based on the data it wishes to send The first read encodes the first 3 bits DO 2 of the data the second read encodes the next three bits D3 5 and the
Download Pdf Manuals
Related Search