Home

MB835 USER`S MANUAL

1. J15 J1 J2 COM2 COMG COMM Serial Port Ping Signal Name 1 DCD Data carrier detect 4 DTR Data terminal ready ei E 6 DSR Data setready 8 CTS Cleatosend 9 RLRingindicato J16 PCIE X4 Slot For IBP835 Gigabit LAN Add on Card FAN1 FAN2 CPU Fan amp System Fan Power Connectors FANI FAN2 is a 3 pin header for system fans The fan must be a 12V 500mA Pin Signal Name L T DIMMO DIMM1 DDR2 DIMM Socket MB835 supports two DDR2 DIMM sockets for a maximum memory of 2GB DDR2 400 533 667 800 Note Used 600MHz processor will support DDR2 400 533 667MHz Used 1200MHz amp 1066MHz processors will support DDR2 400 533 667 800M Hz x1 One DIMM x2 Two DIMM DS Double Side SS Single Side DIMMO DIMM1 x1 SS Memory Modules Y X x1 DS Memory Modules Y X x2 SS Memory Modules Y Y J1 PCIE X4 Slot Signal only support PCIE X1 PCI Slot MB835 User s Manual 77 INSTALLATION m FrFF CONNECTOR LOCATIONS ON IBP835 CN1 RJ45 Gigabit LAN Connectors These four LAN LAN1 2 3 4 connectors are used in conjunction with the four Intel 82574L Gigabit Ethernet controllers on the board gesto 78 MB835 User s Manual BIOS SETUP BIOS Setup This chapter describes the d
2. Capacity size of the hard disk drive Cylinder Number of cylinders Head Number of read write heads Precomp Write precompensation Landing Zone Landing zone Sector Number of sectors The Access Mode selections are as follows CHS HD 528MB LBA HD gt 528MB and supports Logical Block Addressing Large for MS DOS only Auto MB835 User s Manual 23 BIOS SETUP Video This field selects the type of video display card installed in your system You can choose the following video display cards EGA VGA CGA 40 CGA 80 MONO Halt On For EGA VGA SEGA SVGA or PGA monitor adapters default Power up in 40 column mode Power up in 80 column mode For Hercules or MDA adapters This field determines whether or not the system will halt if an error is detected during power up No errors errors But Keyboard But Diskette But Disk Key The system boot will not be halted for any error that may be detected Whenever the BIOS detects a non fatal error the system will stop and you will be prompted The system boot will not be halted for a keyboard error it will stop for all other errors The system boot will not be halted for a disk error it will stop for all other errors The system boot will not be halted for a key board or disk error it will stop for all others 24 MB835 User s Manual BIOS SETUP 4 Advanced BIOS Features This section allows you to configure and
3. Under normal circumstance the user will restart the WDT at regular intervals before the timer counts to zero SAMPLE CODE A THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE include lt stdio h gt include lt stdlib h gt include W627EHG H int main int arge char argv void copyright void void EnableWDT int void DisableWDT void int main int argc char argv unsigned char bBuf unsigned char bTime char endptr copyright if argc 2 printf Parameter incorrect n return 1 if Init W627EHGQ 0 printf Winbond 83627HF is not detected program abort n return 1 bTime strtol argv 1 endptr 10 printf System will reset after 904 seconds bTime EnableWDT bTime return 0 cY s R T1 MB835 User s Manual 43 APPENDIX void copyright void printf n Winbond 83627EHG Watch Timer Tester AUTO DETECT Mu Usage W627E_WD reset_time n Ex W627E WD 3 gt reset system after 3 second n W627E WD 0 gt disable watch dog timer n void EnableWDT int interval unsigned char bBuf bBuf Get W627EHG Reg 0x2D bBuf amp 10 01 Set W627EHG Reg 0x2D bBuf Enable WDTO Set W627EHG
4. separately IDE Primary Secondary Master Slave PIO These fields allow your system hard disk controller to work faster Rather than have the BIOS issue a series of commands that transfer to or from the disk drive PIO Programmed Input Output allows the BIOS to communicate with the controller and CPU directly The system supports five modes numbered from 0 default to 4 which primarily differ in timing When Auto is selected the BIOS will select the best available mode IDE Primary Secondary Master Slave UDMA These fields allow your system to improve disk I O throughput to 33Mb sec with the Ultra DMA 33 feature The options are Auto and Disabled USB Controller The options for this field are Enabled and Disabled By default this field is set to Enabled USB 2 0 Controller The options for this field are Enabled and Disabled By default this field is set to Enabled In order to use USB 2 0 necessary OS drivers must be installed first USB Keyboard Mouse Support The options for this field are Enabled and Disabled By default this field is set to Disabled Hac e r rna 30 MB835 User s Manual BIOS SETUP p M MM 4 Power ON Function This field is related to how the system is powered on such as with the use of conventional power button keyboard or hot keys The default is BUTTON ONLY KB Power ON Password This field allows users to set the password when keyboard power on is the
5. EP80579 Integrated Processor for embedded computing The EP80579 System on a Chip SoC is a new generation processor that is cost optimized for a wide range of applications EP80579 delivers the balance of a powerful IA 32 processor core standards based chipset and acceleration communications focused I O capabilities The EP80579 SoC integrates features into a single device with memory controller hubs IMCH and I O controller hubs ICH The IMCH has built in memory controllers for external memory and the IICH has standard IA I O peripheral capabilities The MB835 s EP80579 IA 32 core is a derivative of the Intel Pentium M processor This low power IA 32 core is based on 90 nm process technology featuring 256 Kbyte L2 cache and 400 533 MHz quad pumped internal front side bus FSB With two DDR2 DIMM sockets on board the board supports up to 2GB of DDR2 system memory It integrates three Gigabit Ethernet MAC interfaces The MAC fully implements the IEEE 802 3z Carrier Sense Multiple Access with Collision Detection CSMA CD method and physical layer specifications The GbE features include interface to PHY devices Multi speed operation 10 100 1000 Mbps The main features of the ECX810 board are Supports Intel EP80579 processors in 600 1066 1200MHz EP80579 built in USB 2 0 host controller supports 2 ports EP80579 built in SATA controller supports 2 ports Two DDR2 SDRAM DIMM Max 2GB memory Integrated Thr
6. LD 0x08 switch to logic device 8 Set W627EHG Reg 0x30 0x01 timer bBuf Get_W627EHG_Reg 0xF5 bBuf amp 10x08 Set_W627EHG_Reg 0 5 bBuf count mode is second Set_W627EHG_Reg OxF6 interval set timer void DisableWDT void Set W627EHG LD 0x08 switch to logic device 8 Set W627EHG Reg 0xF6 0x00 1 watchdog timer Set W627EHG Reg 0x30 0x00 Iwatchdog disabled 44 MB835 User s Manual APPENDIX m THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE include lt dos h gt unsigned int W627EHG BASE void Unlock_W627EHG void void Lock_W627EHG void unsigned int Init WG27EHG void unsigned int result unsigned char ucDid W627EHG BASE 0x2E result W627EHG BASE ucDid Get W627EHG Reg 0x20 if ucDid 0x88 goto Init_Finish W627EHG BASE Ox4E result W627EHG BASE ucDid Get W627EHG Reg 0x20 if ucDid 0x88 goto Init_Finish W627EHG BASE 0x00 result W627EHG BASE Init Finish return result Je sess void Unlock W627EHG void outportb W627EHG INDEX PORT W627EHG UNLOCK outportb W627EHG INDEX PORT 627 UNLOCK void Lock W62
7. MB835 User s Manual INSTALLATION Installations This section provides information on how to use the jumpers and connectors on the MB835 in order to set up a workable system The topics covered are Setting the Jumpers de eee aere 8 Connectors on 835 12 MB835 User s Manual 7 INSTALLATION ms rr ss Setting the Jumpers Jumpers are used on MB835 to select various settings and features according to your needs and applications Contact your supplier if you have doubts about the best configuration for your needs The following lists the connectors on MB835 and their respective functions Jumper Locations on MB835 sse 9 Clear CMOS Setting 10 1 2 AT Emulation ATX Power Selection 10 JP3 CF Card Master Slave Selection sees 10 JP5 Watchdog Timer amp LANI LAN Bypass Settings 11 JP6 1 7 Watchdog Timer amp LAN3 LANA Bypass Settings 11 8 MB835 User s Manual INSTALLATION Jumper Locations on MB835 ES Si Jumper Locations on MB835 sse Page Clear CMOS ttm ete et 10 JP2 AT Emulation ATX
8. SIO GPIO28 Closed JP7 Pin 1 2 amp 3 4 System will reboot JP6 Pin 1 2 upon the time out of watchdog timer Closed Default MB835 User s Manual 71 INSTALLATION Connectors on MB835 The connectors on MB835 allows you to connect external devices such as keyboard floppy disk drives hard disk drives printers etc The following table lists the connectors on MB835 and their respective functions Connector Locations on 835 13 CN1 ATX Power Supply Connector 14 CN2 CN3 Serial ATA Connector 14 CN4 Compact Flash Connector 14 CN5 Front Side Bridge Board to ID370 14 CNG Console iiiter rettet 15 The Console Port is a RJ45 RS 232 port sss 15 CN7 USBO Port Conn ctor eiecti 15 CNS8 RJ45 Gigabit LAN 15 15 SPI Pin Header Debug 15 16 TDM Connector 15 78 PCIE 1 PCI Slot and PCIE slot for ID835 add on card 16 Mini PCI 16 LPC 80 Port Pin Header Debug Use Only 16 J13 PS 2 Keyboard and Mouse Connector sese 16 Jl USBI a la a 16 J15 J2 COM2 COMG Serial Port 17 J16 PCIE Slot For IBP835
9. activated Pressing the Del key immediately allows you to enter the Setup utility If you are a little bit late pressing the Del key POST Power On Self Test will continue with its test routines thus preventing you from invoking the Setup If you still wish to enter Setup restart the system by pressing the Reset button or simultaneously pressing the Ctrl Alt and Delete keys You can also restart by turning the system Off and back On again The following message will appear on the screen Press lt DEL gt to Enter Setup In general you press the arrow keys to highlight items Enter to select the lt PgUp gt and lt PgDn gt keys to change entries F1 for help and Esc to quit When you enter the Setup utility the Main Menu screen will appear on the screen The Main Menu allows you to select from various setup functions and exit choices Hac qas 20 MB835 User s Manual BIOS SETUP s Phoenix AwardBIOS CMOS Setup Ulilit Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Management Setup Set User Password PnP PCI Configurations Save amp Exit Setup PC Health Status Exit Without Saving ESC Quit V gt Select F10 Save amp Exit Setup Time Date Hard Disk Type The sect
10. set the time interval for displaying the first and second characters By default this item is set to 250msec Security Option This field allows you to limit access to the System and Setup The default value is Setup When you select System the system prompts for the User Password every time you boot up When you select Setup the system always boots up and prompts for the Supervisor Password only when the Setup utility is called up APIC Mode APIC stands for Advanced Programmable Interrupt Controller The default setting is Enabled HIEE 2 4 26 MB835 User s Manual BIOS SETUP MPS Version Control for OS This option is specifies the MPS Multiprocessor Specification version for your operating system MPS version 1 4 added extended configuration tables to improve support for multiple PCI bus configurations and improve future expandability The default setting is 1 4 OS Select for DRAM gt 64MB This option allows the system to access greater than 64MB of DRAM memory when used with OS 2 that depends on certain BIOS calls to access memory The default setting is Non OS 2 Small Logo EPA Show The EPA logo appears at the right side of the monitor screen when the system is boot up The default setting is Disabled MB835 User s Manual 27 BIOS SETUP 4 Advanced Chipset Features This Setup menu controls the configuration of the chipset Phoenix AwardBIOS CMOS Setup Utili
11. 5 Add on Card 5 26 710 Mim PCI Connector 2 a erre ANE 16 J11 LPC 80 Port Pin Header Debug Use 16 PS 2 Keyboard and Mouse Connector sse 16 VIA USB Connector cete Nd e PHI RH 16 J15 J1 J2 COM2 COMG Serial Port 2 17 J16 PCIE X4 Slot For IBP835 Gigabit Lan Add on Card biete asl FANI FAN2 FAN3 CPU Fan amp System Fan Power Connector ba DIMMO DIMMI DDR2 DIMM 17 Gwwww svwsOO s xww MB835 User s Manual 73 INSTALLATION CN1 ATX Power Supply Connector Signal Name Pin Pin Signal Name 2 33V 22 33V a o 0 Ground PS ON 5V Ground 56 5V o Ground Power good 20 10 45V 5VSB CN2 CN3 Serial ATA Connector CN4 Compact Flash Connector CN5 Front Side Bridge Board to ID370 Signal Name Pin Signal Name je Reset SW Speaker 5 VCC GND PWR LED HDD LED 11 RELAY LED 13 GND 15 GND 17 Pull up to VCC Pull up to VCC GND 8 10 12 16 GND 18 20 2 24 26 Pi 2 10 12 14 Pull up to VOC 16 18 20 22 24 26 8 14 MB835 User s Manual INSTALLATION 8 CN7 CNE CI E ner Ee ji WU H zm CN6 Console Port The Console Port is an RJ45 RS 232 port Pin Signal N
12. 7EHG G void void Set W627EHG TID un outportb W627EHG INDEX PORT W627EHG LOCK Unlock W627EHG outportb W627EHG INDEX PORT W627EHG LD outportb W627EHG DATA PORT LD Lock W627EHQ O O MB835 User s Manual 45 APPENDIX void Set_ W627EHG Reg u igned char REG uns par char DATA Unlock W627EHG outportb W627EHG INDEX PORT REG outportb W627EHG DATA PORT DATA Lock W627EHQ unsigned char Get W627EHG ned char REG unsigned char Result Unlock W627EHG outportb W627EHG INDEX PORT REG Result inportb W627EHG DATA PORT Lock W627EHG0 return Result THIS CODE AND INFORMATION IS PROVIDED AS IS WITHOUT WARRANTY OF ANY KIND EITHER EXPRESSED OR IMPLIED INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OR FITNESS FOR A PARTICULAR PURPOSE ifndef W627EHG _ H define 627 H 1 222 define W627EHG INDEX _ W627EHG BASE define W627EHG_DATA_PORT Wez7EHG BASEEN define W627EHG REG LD 0x07 define W627EHG_UNLOCK 0x87 define W627EHG_LOCK OxAA void Set W627EHG LD unsigned char void Set W627EHG Reg unsigned char unsigned char unsigned char Get W627EHG Reg unsigned char endif __W627EHG_H 46 MB835 User s Manual
13. Gigabit LAN Add on Card 17 FANI FAN2 FAN3 CPU Fan amp System Fan Power Connector 17 DIMMO DIMM1 DDR2 DIMM Socket eee 17 Connector Locations on 0835 0 15 PCIE Slot Signal only support PCIE X1 17 PCEN POES Ot e enra eaea e naana ea E a SER REEDEL EA SrA 17 Connector Locations on IBP835 18 RJ45 Gigabit LAN Connectors 18 72 MB835 User s Manual INSTALLATION Connector Locations on MB835 16555665555 LG Fi mH I m EaP DIMMC pz b 4 53 ps _ E Connector Locations on 835 13 CNI ATX Power Supply Connector 14 CN2 Serial ATA Connector 14 CNA Compact Flash Connector 2 14 CNS Front Side Bridge Board to 0370 2 2 2224 1 10000000000030 0 00 14 CN6 Console Port ci err E 15 The Console Port is a RJ45 RS 232 port CN7 USBO Port Connector CNS RJ45 Gigabit LAN Connectors JS SPLPin Header Debug OMY 250 eee it e recedens 15 16 TDM TIE Connector 15 J8 PCIE 1 PCI Slot And PCIE X1 Slot For ID83
14. MB835 Intel EP80579 Motherboard USER S MANUAL Version 1 0 Acknowledgments Award is a registered trademark of Award Software International Inc PS 2 is a trademark of International Business Machines Corporation Intel and Intel EP80579 Integrated Processor are registered trademarks of Intel Corporation Microsoft Windows is a registered trademark of Microsoft Corporation Winbond is a registered trademark of Winbond Electronics Corporation All other product names or trademarks are properties of their respective owners ii MB835 User s Manual Table of Contents Introduction ttes 1 Product 1 Checklist iine HERO 2 MB835 3 Board aa 5 Installations 7 Setting the Jumpers 8 Connectors on MB835 12 BIOS SelUp E 19 Drivers Installation 39 41 Bypass tete teet ea nee 41 Watchdog Timer Configuration 43 M 1 MB835 User s Manual This page is intentionally left blank Taw6n I iv MB835 User s Manual INTRODUCTION Introduction Product Description The MB835 motherboard incorporates the Intel
15. Power Selection 10 JP3 CF Card Master Slave Selection esee 10 JP5 Watchdog Timer amp 2 Bypass Settings 11 JP6 JP7 Watchdog Timer amp LAN3 LANA Bypass Settings 11 MB835 User s Manual 9 INSTALLATION DINE JP1 Clear CMOS Setting 3 Clear CMOS AT Emulation Note AT Emulation does not require pressing the power button to turn on the system plugging the AC power will turn on the system JP3 CF Card Master Slave Selection CF Card Setting FEN 70 MB835 User s Manual INSTALLATION mY JP4 JP5 Watchdog Timer amp LAN1 LAN2 Bypass Settings JP4 Pin 1 2 amp 3 4 System will bypass LANs JP5 Pin 1 2 upon the time out of watchdog timer Closed JP4 Pin 1 2 amp 3 4 Open System LANs bypass function JP5 Pin 2 3 controlled by SIO GPIO27 Closed JP4 Pin 1 2 amp 3 4 ES System will reboot JP5 Pin 1 2 upon the time out of watchdog timer Closed Default JP6 JP7 Watchdog Timer amp LAN3 LAN4 Bypass Settings JP6 JP7 Setting Function JP7 Pin 1 2 amp 3 4 Open System will bypass LANs JP6 Pin 1 2 upon the time out of watchdog timer Closed JP7 Pin 1 2 amp 3 4 SE System LANs bypass function JP6 Pin 2 3 controlled by
16. ame RTS Request to send DTR Data terminal ready TXD Transmit data DSR Data set ready 8 OS CN7 USBO Port Connector 6 CN8 RJ45 Gigabit LAN Connectors These four LAN LANI 2 3 4 connectors are used in conjunction with the four Intel 82574L Gigabit Ethernet controllers on the board J5 SPI Pin Header Debug Only J6 TDM T1 E1 Connector 16 The TDM interface for support up to 12 T1 E1 links Signal Name Signal Name 6 DOS 8 RX FRAME TX FRAMEO 9 MB835 User s Manual 75 INSTALLATION J8 PCIE 1 PCI Slot and PCIE X1 Slot for ID835 add on card J10 Mini PCI Connector J11 LPC 80 Port Pin Header Debug Use Only Signal Name Pin Pin Signal Name LADO DEE LAD3 7 s GND 9 913 PS 2 Keyboard and Mouse Connector J13 a 10 pin header has functions for both keyboard and mouse Signal Name Pin Pin Signal Name KB clock 9 4 Mouse tock KB data 3 Mouse dat Vec Fe xe es s J14 USB1 Connector Signal Name Pin Pin Signal Name Lye USB2 5 6 NC Grund 7 8 Er Er E EL Er El 3 76 MB835 User s Manual INSTALLATION
17. ation software halt or when power is off Block Diagram Bypass Relays CN2 Ethemet 1 RJ45 A Ethemet 2 y RAMS B Normal State Relays are Energized WDT Relay VO Command Driver GPIO Communication States There are two communications states for the bypass function 1 Normal State 2 Bypass State A watchdog timer WDT or a GPIO are used to control and switch the communication between the two states The block diagram in the section above shows the Normal State where the two Ethernet ports work independently The following diagram shows the Bypass State where the two Ethernet ports are bypassed together i MB835 User s Manual 41 APPENDIX Bypass Relays ES CN2 Ethemet l RM5 A Ethemet 2 R45 B Bypass State Relays are Dis energized WDT Relay Driver GPIO HO Command lt lt lt lt 42 MB835 User s Manual APPENDIX Watchdog Timer Configuration The WDT is used to generate a variety of output signals after a user programmable count The WDT is suitable for use in the prevention of system lock up such as when software becomes trapped in a deadlock Under these sorts of circumstances the timer will count to zero and the selected outputs will be driven
18. button is pressed for more than four seconds or enters the suspend mode when pressed for less than 4 seconds Wake up by PCI Card By default this field is disabled MB835 User s Manual 33 BIOS SETUP rss Resume by Alarm This field enables or disables the resumption of the system operation When enabled the user is allowed to set the Date and Time Reload Global Timer Events The HDD FDD COM LPT Ports and PCI PIRQ are I O events that can prevent the system from entering a power saving mode or can awaken the system from such a mode When an I O device wants to gain the attention of the operating system it signals this by causing an IRQ to occur When the operating system is ready to respond to the request it interrupts itself and performs the service G E 34 MB835 User s Manual BIOS SETUP m r PNP PCI Configurations This option configures the PCI bus system All PCI bus systems on the system use INT thus all installed PCI cards must be set to this value Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations Init Display First PCI Slot ITEM HELP Reset Configuration Data Disabled Menu Level gt Resources Controlled By Auto ESCD IRQ Resources Press Enter PCI VGA Palette Snoop Disabled PCI Express relative items Maximum Payload Size 4096 Init Display First The default setting is PCI Card Reset Confi
19. ect the system and Setup utility User Password sets a password that will be used exclusively on the system To specify a password highlight the type you want and press Enter The Enter Password message prompts on the screen Type the password up to eight characters in length and press Enter The system confirms your password by asking you to type it again After setting a password the screen automatically returns to the main screen To disable a password just press the Enter key when you are prompted to enter the password A message will confirm the password to be disabled Once the password is disabled the system will boot and you can enter Setup freely Save amp Exit Setup This option allows you to determine whether or not to accept the modifications If you type Y you will quit the setup utility and save all changes into the CMOS memory If you type N you will return to Setup utility Exit Without Saving Select this option to exit the Setup utility without saving the changes you have made in this session Typing Y will quit the Setup utility without saving the modifications Typing N will return you to Setup utility Harc 3 38 MB835 User s Manual DRIVERS INSTALLATION Drivers Installation Intel EP80579 Software Drivers for Embedded Applications Intel EP80579 Software Drivers for Embedded Applications contains all software drivers needed to utilize hardware featu
20. ee Gigabit Ethernet MACs PHY Intel 82574L PCI E Controller 2x SATA 2x USB 2 0 COM Watchdog timer Interface connector for daughter board ID835 IBP835 7 MB835 User s Manual INTRODUCTION Checklist Your ECX810 package should include the items listed below e The MB835 Mother board e This User s Manual e CD containing chipset drivers and flash memory utility e Optional cables for Keyboard mouse Serial port Serial ATA 2 MB835 User s Manual INSTALLATION 835 Specifications MB835 Motherboard Frequency 600 1000 1200 MHz L2 cache 256kb 2x DDR2 sockets supporting DDR2 400 533 667 and 800 Max 2GB memory with ECC 600Mhz CPU at DDR2 533 only Integrated Intel amp Architecture IA processor and chipset MCH ICH technology 1088 Ball FCBGA package Award BIOS PCIe Switch PEX8509 of PLX 8Lanes 8Ports PCIe switch up 4 lanes down Llanes Connect from PCleX4 bus of EP80579 Connect to Intel 825741 GbE JM368 PCIe to PATA bridge PEX8112 PCIe to PCI bridge golden finger PCI bridge PEX8112 of PLX PCIe to PCI bridge max for 4PCI Connect from PCleX1 bus of PEX8509 downstream Connect to HIEN 7964 IPSec onboard MiniPCI slot PCI32 golden finger Ethernet controller EP80579 integrated GbE MACs RGMII link to Marvell 88E1145 Quad PHYs with 3x RJ45 on the edge connector Onboard Intel 82574L GbE with RJ45 on the edge connector Default ETHO ETH3
21. em sounds a warning This function can help prevent damage to the system that is caused by overheating Temperatures Voltages These fields are the parameters of the hardware monitoring function feature of the motherboard The values are read only values as monitored by the system and show the PC health status Hac 3 36 MB835 User s Manual BIOS SETUP r Frequency Voltage Control This section shows the user how to configure the processor frequency Phoenix AwardBIOS CMOS Setup Utility Frequency Voltage Control Auto Detect PCI Clk Disabled ITEM HELP Spread Spectrum Modulated Disabled Menu Level gt Auto Detect PCI Clk This field enables or disables the auto detection of the PCI clock Spread Spectrum Modulated This field sets the value of the spread spectrum The default setting is Disabled This field is for CE testing use only MB835 User s Manual 37 BIOS SETUP 4 Load Fail Safe Defaults This option allows you to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features Load Optimized Defaults This option allows you to load the default values to your system configuration These default settings are optimal and enable all high performance features Set Supervisor Password These two options set the system password Supervisor Password sets a password that will be used to prot
22. grated Processor with QuickAssist Technology Reserved interface headers for future connection to proprietary E1 T1 board Power ATX Yes 256 segments 0 1 2 255 sec min MB835 User s Manual 3 INSTALLATION mr PCIeX4 bus of M B PCIe switch PEX8509 of PLX Genl 5 lanes 8 ports PCIe switch up 4lanes down Hanes Connect from PCIeX4 bus of M B Connect to 4x Intel 82574L GbE Ethernet controller 4x onboard Intel 82574L GbE optional 2x GbE Connect from PCIeX1 bus of PEX8509 downstream Connect to RJ45 on edge connector 4x RJ45 with LED connector Model 10835 Riser Card Expansion slot M B side PCI and 1x slot connect from M B Expansion slot Top PCI slot for additional card Bottom PCIeXA slot for additional card 4 MB835 User s Manual INSTALLATION Board Dimensions L ln 3 TEN me mmm m r MB835 User s Manual 5 INSTALLATION m s This page is intentionally left blank 6
23. guration Data This field allows you to determine whether to reset the configuration data or not The default value is Disabled Resources Controlled by This PnP BIOS can configure all of the boot and compatible devices with the use of a PnP operating system such as Windows 95 PCI VGA Palette Snoop Some non standard VGA display cards may not show colors properly This field allows you to set whether or not MPEG ISA VESA VGA cards can work with PCI VGA When this field is enabled a PCI VGA can work with an MPEG ISA VESA VGA card When this field is disabled a PCI VGA cannot work with an MPEG ISA VESA card Maximum Payload Size The default setting of the PCI Express Maximum Payload Size is 4096 Gwwww csFw MB835 User s Manual 35 BIOS SETUP PC Health Status This section shows the parameters in determining the PC Health Status These parameters include temperatures fan speeds and voltages Phoenix AwardBIOS CMOS Setup Utility CPU Warning Temperature Current System Temp Current CPU1 Temperature Current CPU2 Temperature FANS Speed FAN1 Speed FAN2 Speed Vcore 12V 1 8V 5V 3 3V VBAT V 5VSB V PC Health Status Disabled ITEM HELP 34 C 93 F Menu Level gt 42 C 107 F 41 C 105 F 0 RPM 7031 RPM 0 RPM 1 30 V 12 34 V 1 89V 4 99 V 3 15V 3 15 V 5 31 V CPU Warning Temperature This field allows the user to set the temperature so that when the temperature is reached the syst
24. ifferent settings available in the Award BIOS that comes with the board The topics covered in this chapter are as follows BIOS Introduction inia pn 20 BIOS Setup zoe eo 20 Standard CMOS Setup 22 Advanced BIOS 25 Advanced Chipset Features 28 Intesrat d Periph eralSu eee esed 29 Power Management Setup essere 32 PNP PCI Configurations 35 Health Status eoo te eere e 36 Frequency Voltage Control 37 Load Fail Safe Defaults 38 Load Optimized Defaults 38 Set Supervisor User Password 38 Save amp Exit aee 38 Exit Without 38 GwwwwrwmOo LLLIIJ MB835 User s Manual 79 BIOS SETUP C X BIOS Introduction The Award BIOS Basic Input Output System installed in your computer system s ROM supports Intel processors The BIOS provides critical low level support for a standard device such as disk drives serial ports and parallel ports It also adds virus and password protection as well as special support for detailed fine tuning of the chipset controlling the entire system BIOS Setup The Award BIOS provides a Setup utility program for specifying the system configurations and settings The BIOS ROM of the system stores the Setup utility When you turn on the computer the Award BIOS is immediately
25. improve your system and allows you to set up some system features according to your preference Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features CPU Feature Press Enter ITEM HELP Hard Disk Boot Priority Press Enter Virus Warning Disabled Menu Level gt CPU 11 amp L2 Cache Quick Power On Self Test First Boot Device Second Boot Device Third Boot Device Boot Other Device Boot Up NumLock Status Gate A20 Option Typematic Rate Setting Typematic Rate Chars Sec Typematic Delay Msec Security Option APIC Mode MPS Version Control for OS OS Select For DRAM gt 64MB Small Logo EPA Show Enabled Enabled Removable Hard Disk USB CDROM Enabled On Fast Disabled 6 250 Setup Enabled 1 4 Non OS2 Disabled CPU Feature Press Enter to configure the settings relevant to CPU Feature Hard Disk Boot Priority With the field there is the option to choose aside from the hard disks connected Bootable add in Cards which refers to other external devices Virus Warning If this option is enabled an alarm message will be displayed when trying to write on the boot sector or on the partition table on the disk CPU L1 and L2 Cache Cache memory is additional memory that is faster than conventional DRAM system memory CPUs from 486 type on up contain internal cache memory and most but not all modern PCs have additional external cache memory When the CPU requests data the system transfers
26. ion below the setup items of the Main Menu displays the control keys for this menu At the bottom of the Main Menu just below the control keys section there is another section which displays information on the currently highlighted item in the list Note If the system cannot boot after making and saving system changes with Setup the Award BIOS supports an override to the CMOS settings that resets your system to its default Warning It is strongly recommended that you avoid making any changes to the chipset defaults These defaults have been carefully chosen by both Award and your system manufacturer to provide the absolute maximum performance and reliability Changing the defaults could cause the system to become unstable and crash in some cases Gr MB835 User s Manual 21 BIOS SETUP EE Standard CMOS Setup Standard CMOS Setup choice allows you to record some basic hardware configurations in your computer system and set the system clock and error handling If the motherboard is already installed in a working system you will not need to select this option You will need to run the Standard CMOS option however if you change your system hardware configurations the onboard battery fails or the configuration stored in the CMOS memory was lost or damaged Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Tue Jul 1 2008 Item Help Time hh mm ss 12 00 00 Menu Level gt DE Channel 0 Ma
27. mode of the Power ON function Hot Key Power ON This field sets certain keys also known as hot keys on the keyboard that can be used as a switch to power on the system Onboard Serial Port ICH Serial Port These fields allow you to select the onboard serial and parallel ports and their addresses The default values for these ports are Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 ICH Serial Port 1 3ES IRQ5 ICH Serial Port 2 2E8 IRQ7 PWRON After PWR Fail This field sets the system power status whether on or off when power returns to the system from a power failure situation puas wvnr rsi MB835 User s Manual 37 BIOS SETUP Power Management Setup Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Power Management Video Off Method Video Off In Suspend Suspend Type Modem Use IRQ Suspend Mode HDD Power Down Soft Off by PWR BTTN Wake Up by PCI card Resume by Alarm Date of Month Alarm Time hh mm ss Alarm Reload Global Timer Events Primary IDE 0 Primary IDE 1 Secondary IDE 0 Secondary IDE 1 FDD COM LPT Port PCI PIRQ A D ACPI Function Enabled User Define SYNC Blank Yes Stop Grant 3 Disabled Disabled Instant Off Enabled Disabled 0 0 0 0 ITEM HELP Menu Level gt Disabled Disabled Disabled Disabled Disabled Disabled Enable this function to support ACPI Advance Configuration and Power Interface Po
28. nChip IDE Device IDE HDD Block Mode Enabled ITEM HELP IDE DMA transfer access Enabled Menu Level gt On Chip Primary PCI IDE Enabled IDE Primary Master PIO Auto IDE Primary Slave PIO Auto IDE Primary Master UDMA Auto IDE Primary Slave UDMA Auto On Chip Secondary PCI IDE Enabled IDE Secondary Master PIO Auto IDE Secondary Slave PIO Auto IDE Secondary Master UDMA Auto IDE Secondary Slave UDMA Auto On Chip Serial ATA Setting On Chip Serial ATA IDE Phoenix AwardBIOS CMOS Setup Utility Onboard Device USB Controller Enabled ITEM HELP USB 2 0 Controller Enabled Menu Level gt USB Keyboard Function Disabled USB Mouse Function Disabled Phoenix AwardBIOS CMOS Setup Utility SuperlO Device POWER ON Function BUTTON ONLY ITEM HELP KB Power ON Password Enter Menu Level gt Hot Key power ON Ctrl F1 Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 PWRON After PWR Fail Off MB835 User s Manual 29 BIOS SETUP 4 IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive IDE DMA transfer access Use this field to enable or disable IDE DMA transfer access On chip Primary PCI IDE Enabled This field by default is enabled On chip Primary Secondary PCI IDE The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel
29. res on the Intel EP80579 Integrated Processor In addition to the standard OS drivers offered with other Intel architecture platforms this software package contains drivers specific to developing embedded applications These drivers provide access to and control of the three Ethernet MACs and two Controller Area Network CAN interfaces as well as internal processor items such as Enhanced Direct Memory Access EDMA Because the core of the Intel EP80579 Integrated Processor is based on Intel architecture operating systems currently supporting Intel architecture will function without this software package For the most recent software package updates from Intel please visit downloadcenter intel com The following operating systems are supported on the Intel EP80579 Integrated Processor Microsoft Windows XP Embedded SP2 Red Hat Enterprise Linux 5 Wind River Linux 2 0 Wind River VxWorks 6 6 FreeBSD 6 2 The Driver CD that comes with the board contains software drivers for Windows XP Embedded The path location of the drivers in the CD is intel EP80579 Gwwww srrswrcr r rn MB835 User s Manual 39 DRIVERS INSTALLATION m rrIIsmsssrsa This page is intentionally left blank gt 40 MB835 User s Manual APPENDIX Appendix Bypass and WDT The bypass function is used to link or short two independent Ethernet ports when user s applic
30. ster None Change the day month DE Channel 0 Slave None Year and century DE Channel 1 Master None DE Channel 1 Slave None Video EGA VGA Halt On All Errors Base Memory 640K Extended Memory 1046528K Total Memory 1047552K At the bottom of the menu are the control keys for use on this menu If you need any help in each item field you can press the F1 key It will display the relevant information to help you The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following describes each item of this menu Date The date format is Day Sun to Sat Month 1 to 12 Date 1 to 31 Year 1999 to 2099 3 22 MB835 User s Manual BIOS SETUP BEER To set the date highlight the Date field and use the PageUp PageDown or keys to set the current time Time The time format is Hour 00 to 23 Minute 00 to 59 Second 00 to 59 To set the time highlight the Time field and use the lt PgUp gt lt PgDn gt keys to set the current time IDE Channel Master Slave The onboard PCI IDE connector provides Primary and Secondary channels for connecting up to two IDE hard disks or other IDE devices Press Enter to configure the hard disk The selections include Auto Manual and None Select Manual to define the drive information manually You will be asked to enter the following items Capacity
31. the requested data from the main DRAM into cache memory for even faster access by the CPU These allow you to enable speed up memory access or disable the cache function Quick Power On Self Test When enabled this field speeds up the Power On Self Test POST after the system is turned on If it is set to Enabled BIOS will skip some items MB835 User s Manual 25 BIOS SETUP 4 First Second Third Boot Device These fields determine the drive that the system searches first for an operating system The options available include Removable Hard Disk CDROM USB CDROM and Disable Boot Other Device These fields allow the system to search for an OS from other devices other than the ones selected in the First Second Third Boot Device Boot Up NumLock Status This allows you to activate the NumLock function after you power up the system Gate A20 Option This field allows you to select how Gate A20 is worked Gate A20 is a device used to address memory above 1 MB Typematic Rate Setting When disabled continually holding down a key on your keyboard will generate only one instance When enabled you can set the two typematic controls listed next By default this field is set to Disabled Typematic Rate Chars Sec When the typematic rate is enabled the system registers repeated keystrokes speeds Settings are from 6 to 30 characters per second Typematic Delay Msec When the typematic rate is enabled this item allows you to
32. ty Advanced Chipset Features System BIOS Cacheable Enabled ITEM HELP Video BIOS Cacheable Disabled Menu Level gt Memory Hole at 15M 16M Disabled IICH PCI Express Root Port Press Enter System BIOS Cacheable The setting of Enabled allows caching of the system BIOS ROM at F000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result Video BIOS Cacheable The Setting Enabled allows caching of the video BIOS ROM at C0000h F7FFFh resulting in better video performance However if any program writes to this memory area a system error may result Memory Hole At 15M 16M In order to improve performance certain space in memory can be reserved for ISA cards This memory must be mapped into the memory space below 16 MB The choices are Enabled and Disabled 2 2 2 28 MB835 User s Manual BIOS SETUP rr Integrated Peripherals This section sets configurations for your hard disk and other integrated peripherals The first screen shows three main items for user to select Once an item selected a submenu appears Details follow Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals OnChip IDE Device Press Enter ITEM HELP Onboard Device Press Enter Menu Level gt SuperlO Device Press Enter ICH Serial Port Device ICH Serial Port 1 3E8 IRQ5 ICH Serial Port 2 2E8 IRQ7 Phoenix AwardBIOS CMOS Setup Utility O
33. wer Management This field allows you to select the type of power saving management modes There are four selections for Power Management Min Power Saving Max Power Saving User Define Minimum power management Maximum power management Each of the ranges is from 1 min to Ihr Except for HDD Power Down which ranges from 1 min to 15 min 32 MB835 User s Manual BIOS SETUP 2 2 22 22 Video Method This field defines the Video Off features There are three options V H SYNC Blank Default setting blank the screen and turn off vertical and horizontal scanning DPMS Allows BIOS to control the video display Blank Screen Writes blanks to the video buffer Video Off In Suspend When enabled the video is off in suspend mode The default setting is Yes Suspend Type The default setting for the Suspend Type field is Stop Grant Modem Use IRQ This field sets the IRQ used by the Modem By default the setting is 3 Suspend Mode When enabled and after the set time of system inactivity all devices except the CPU will be shut off HDD Power Down When enabled and after the set time of system inactivity the hard disk drive will be powered down while all other devices remain active Soft Off by PWRBTN This field defines the power off mode when using an ATX power supply The nstant Off mode allows powering off immediately upon pressing the power button In the Delay 4 Sec mode the system powers off when the power
34. with bypass optional function can be controlled by GPIO and WDT IPSec HIFN 7964 pin to pin compatible with 7965 and 7966 optional function Connect from PCI bus from PEX8112 PCI bus must be 32bit 66Mhz USB Intel EP80579 build in 2X USB2 0 host controller with 1x USB stack connector on edge connector Intel EP80579 build in 2X SATA controller with 2XSATA onboard 7 pin shrouded vertical connector Compact flash Jmicron JM368 PCIe to PATA bridge PATA Connect from PCIeX1 bus of PEX8509 downstream Connect to onboard CF type II socket support UDMA mode LPC Winbond W83627DHG COMI with RJ45 on edge connector for console redirection for LCM function Hardware monitor COM3 amp COMA from EP80579 built in UART with box header Keyboard mouse 5 2 keyboard amp mouse support with pitch 2 54mm pin header Expansion slot amp 1x onboard MiniPCI slot connector 1x LAN module expansion connector 1x pitch 2 0mm 44 pin HDD connector for ID370 LED board Edge connector 4x RJ45 connector with LED for GbE 1x USB vertical connector 1x console redirection via RJA5 without LED Onboard connector ATX 20P connector 3x 3P fan header with Smart FAN function 2x SATA controller with 2x SATA onboard 7 pin shrouded vertical connector 1 port for LCM 2x COM ports for COM3 amp 4 1 PS 2 keyboard mouse 1x USB2 0 1 right angle SAMTEC MEC1 140 02 L D RA1 SL Hi Speed connector for LAN module IBP835 TDM Intel EP80579 Inte

MB835 USER`S MANUAL

Contents

Download Pdf Manuals

Related Search

Related Contents