WARNING!!!
Contents
1. Selection of the mode from the list Screen of the clock 17 45 The screen shows the current time and the number ofthe activated time zone Time correction is possible after pressing the CONFIRM button 6 and the minutes field begins blinking The blinking value can be altered with the buttons or Pressing the CHOOSE button 7 you come to the hours field that can be set also with the buttons or Pressing the CONFIRM button 6 confirms the changes the clock field will stop blinking Screen of setting the parameters Normally the parameters level equals to 0 namely the parameters aren t available After changing the level to 1 2 3 or 4 successive screens show the values of the parameters The last screen contains after which it comes back to the above mentioned screens Parameter 77 S lt e Unit Al Py Upper and Parameter value change with lower thershold of the changes PARAMETERS ADJUST THE CONTROL UNIT TO THE PROPERTIES OF THE FIREPLACE AND CENTRAL HEATING SYSTEM THEIR CHANGE OUGHT TO BE CONSULTED WITH THE FIREPLACE PRODUCER ILL CONSIDERED MODIFICATIONS CAN CAUSE UNSTABLE AND INEFFICIENT OPERATION OF THE SYSTEM PARAMETERS LEVEL 1 Ne NAME RANGE 20 FIREPLACE 45 85 C 55 C Preset temperature of the fireplace kept by the cont2. blinks 3 times the button gt 3 blinks Button CONFIRM gt 3 stops blinking the Parameters Level 3 has been chosen Button CHOOSE gt current value of the lt 50 gt ChokeV State OFF parameter shows up Button CONFIRM gt current value you want to change starts blinking Buttons and gt you set the new value Button CONFIRM gt we confirm the new value Repeatedly the button CHOOSE till the parameter end setting screen appears JJ PARAMETERS LEVEL 3 PARAMETERS CAN BE CHANGED AT THE UNLOCKED PASSWORD Rundown 6 30min imm e oo time of the BUF pump Extending the run time of TimeBUF the pump after ending the loading of the BUF 64 DeltaKSL 0 20 C 5 C Minimal temperature difference between BUF and KSL required for the KSL pump P1 to run 21 ALARM 75 95 C 85 C Fireplace temperature T3 at which the alarm turns on Temp 24 BUF ALARM Buffer limit temperature T1 at which the alarm generates Temp 75 95 C 85 C 26 ALARM Temp g80 200 C 175 C KSL solar collector limit temperature T2 at which KSL the alarm generates 23 FPLACE OFF 525 C 10 C Decreasing fireplace temperature in relation to preset temperature Temp at whose exceeding the countdown of 30mins begins up to the switch off of fireplace stop condition at FIREPLACE MODE AUTO 0 fireplace temp higher than ControlR
3. temperature T1 by the lt 61 gt DeltaBUF parameter see see PARAMETERS LEVEL 1 The third function is controlling the loading pump of the BUF container from the solar collector KSL P1 The pump of the collector P1 runs if the temperature of the collector T2 exceeds the temperature of the buffer T1 by the parameter value lt 64 gt DeltaKSL The next function is to control the circulating pump P3 of central heating system The pump works if the buffer temperature exceeds the CH ON value Fig 1 Basic operation configuration of the control unit WAW Warm Applicable Water container boiler FIREPLACE Water jacket fireplace BUF Buffer container KSL Solar collector or another heat source CH Central heating system T1 Temperature sensor of the BUF buffer container T2 Temperature sensor of the KSL solar collector T3 Temperature sensor of the FIREPLACE fireplace water jacket P1 Pump loading the BUF from KSL P2 Pump loading the BUF from FIREPLACE P3 Circulating pump CH PP Electronically controlled air damper of the fireplace j Admission date Realization date Signature Remarks TANIA P N PRODUCENT ZASILACZY SIECIOWYCH ISO 9001 2000 CE CONFORMITY DECLARATION Ref No 58 RT 01 2007 1 B We ZAK AD ELEKTRONICZNY TATAREK Jerzy Tatarek 75 Swieradowska St 50 559 Wroclaw declare under our s
4. 3 230V 50HZ Fig 3 Electrical wiring diagram PP Air damper T1 Temperature sensor of the BUF container buffer container T2 Temperature sensor of the KSL collector solar collector T3 Temperature sensor of the fireplace water jacket FIREPLACE P1 Pump loading the BUF container from KSL P2 Pump loading the BUF container from FIREPLACE P3 CH circulating pump 2 1 Control unit status diode alarm red standby orange operation green manual MAN blinking green Graphic display Button F1 switch on off power supply Increase button Decrease button Confirmation button Parameter selection button Button F2 ESC return to the main screen ia a a 3 1 Time zones The control unit is equipped with the clock which enables the automatic change of the control unit operation at different times of day 24 hrs are divided into 5 time zones 1 2 3 e4 e5 Each zone has a start time FROM and an end time TO The same start and end time means the zone isn t active which doesn t change the settings of the control unit The time zones can overlap each other in that case binding are the settings for the active zone of higher number THIS SOFTWARE VERSION DOES NOT INCLUDE THE TIME ZONES 3 2 Screens Alarm screen ALARM is not seen till the following alarm situation takes place 1 Damage of the T1 BUFFER sensor The BUF temp sensor T1 damaged text shows up 2 Damage of the T2 KSL sensor The KSL temp s
5. WARNING WE INFORM THAT THE OFFERED CONTROL UNIT CAN BE ONLY APPLIED TO THE FITTING DEVICES THE REQUIREMENTS OF THE TECHNICAL AND BUILDING STANDARDS CONCERNING THE CORRECTNESS OF STOVE FITTER AND HEATING SYSTEMS HANDLING THE FIREPLACE INPUTS MUST BE MET WRONG USAGE OF THE CONTROL UNIT CAN LEAD BOTH TO ITS DAMAGE AND IN EXTREME CASES TO THE DAMAGE OF THE FIREPLACE INPUT AND HEATING SYSTEM CONTROLLED BY THE FIREPLACE AS WELL ALONG WITH THE DEVICES THAT COOPERATE WITH THE HEATING SYSTEM WINANS Zak ad elektroniczny TATAREK Jerzy Tatarek 50 559 Wroclaw 75 Swieradowska st ph 071 367 21 67 373 14 88 fax 373 14 58 Tax index number 899 020 2 1 48 Bank account BZ WBK S A WROCLAW 6910901522 0000 0000 5201 9335 www tatarek com pl e mail tatarek tatarek com pl NI INIEK RT08G_BUF_SOLAR 2012 v 3 0 ANG Zak ad elektroniczny TATAREK Jerzy Tatarek USER MANUAL Program version 3 0 30 07 2012 FIREPLACE LUX RT 08G BUF SOLAR CONTROL UNIT OF THE HEATING SYSTEM WITH THE FIREPLACE CONTROLLED BY THE AIR DAMPER The RT 08G BUF SOLAR control unit controls the heating system based on the water jacket fireplace that is a heat source in which the combustion process is controlled by the air damper The heat receivers is the buffer container BUF which is additionally loaded up from the solar collector KSL The control unit is equipped with its own emergency power source breaks in power supplyin
6. c discharge 2 and overvoltage in the mains 3 Burnt fuses are not subject to warranty replacement Date of sale Seller s signature and stamp ARGO FILM Recycling Plant No 6 180 Krakowska st 52 015 Wroclaw Register No GIOS E 0002240WZ Worn out electronic the utilization collection place where will 0 515 122 142 be accepted for free and electric devices must be transfered to Ph 071 794 43 01 as INIA Gk Y Zak ad elektroniczny TATAREK Jerzy Tatarek 50 559 Wroclaw 75 Swieradowska st ph 071 367 21 67 373 14 88 fax 373 14 58 tax index number 899 020 21 48 Bank account BZ WBK S A O WROCLAW 6910901522 0000 0000 5201 9335 www tatarek com pl E mail tatarek tatarek com pl 4 Installing the control unit THE CONTROL UNIT IS SUPPLIED BY 230V 50HZ ANY MOVES REGARDING INSTALLATION SHOULD BE MADE AT THE DISCONNECTED MAINS THECONTROLUNIT HAS TO BE CONNECTED TO THE MAINS WITH THE ZERO PIN THECONTROLUNIT SHOULD NOT BE EXPOSED TO WATER AFFECTING ITS ENVIRONS OUGHT TO BE CLEAN THE PRODUCER DOESN T TAKE ANY RESPONSIBILITY FOR DAMAGES CAUSED BY WRONG USAGE OF THE CONTROL UNIT Connection diagram of the elements of the control unit is presented on fig 3 PP AIR DAMPER RED SS a ey BLUE fe a ee BLACK _ Saag 2 Temperature sensors Pump P1 230V 50Hz N MAINS PE 230V 50Hz Pump P2 230V 50Hz Pump P
7. elayTemp 12 CONTROL _0 6 2 Relay 2 KSL temperature is higher than ControlRelayTemp BUF pump P2 runs KSL pump P1 runs 5 CH pump P3 runs 6 ALARM is turned on see Alarm screens 16 Control 5_ 195 C 60 C Limit temperature at which the CONTROL relay turns on RelayTemp S Depending on the lt 12 gt CONTROL Relay parameter 51 Choke V ee 2 Control type of the air damper Mode Continuous control servomotor of the air damper is always active Dynamic control servomotor of the air damper 1s active only if the position change of the valve is needed Parameter number No is of auxiliary role it helps to identify the name e g for different language versions PARAMETERS LEVEL 4 RESET OFF ON Setting the l Setting the vanes ON causes henccall ofall parambterste of ON causes the recall of all parameters to their default pre sets and restarts the control unit 0000 PASSWORD OFF 92 PASSWORD 0 9999 0000 gt PASSWORD ON Service OFF OFF The ON value causes diagnostics screen to be added Screen for servicing J0 Automatic operation AUTO is activated by pressing the ON OFF button 3 The air damper is fully opened In 2hrs the fireplace ought to heat itself and reach the preset temperature stabilized by air damper movements From that moment the temperature fall to the preset temperature by more than 10 C the lt 23 gt FPLACE OFF Temp parame
8. ensor T2 damaged text shows up 3 Damage of the T3 sensor of the fireplace The Fplace temp sensor T3 damaged text shows up 4 The exceeding of the limit temperature of the fireplace defined by the lt 21 gt ALARM Temp parameter The too high temp of the fireplace text shows up 5 The exceeding of the limit temperature of the buffer defined by the lt 24 gt BUF ALARM Temp parameter The too high temp of the buffer text shows up 6 The exceeding of the limit temperature of the collector defined by the lt 26 gt ALARM Temp KSL parameter The too high temp of the collector text shows up Alarm situation is accompanied by a broken sound alarm that can be turned off by pressing the CONFIRM button 6 In the emergency of exceeding the temperature the corresponding pumps start to run to cool off the system The KSL protection ha a higher priority than limiting the BUF temperature Screen of the fireplace operation shows the current temperature of the fireplace and the level of air damper opening Current Temperature of tme the water jacket of the fireplace T3 X Q a Time zone s Ze s k Operation mode of Air damper x the fireplace opening Preset temperature It s astable state that is in order to change it you need to press the CHOOSE button 7 During appearing this screen you can change the preset temperature of
9. er season rundown of the pump by switching it on for 1 min if it doesn t operate for a week 2 3 Operation of the KSL pump P1 The collector pump P1 runs if the collector temperature T2 exceeds the buffer temperature T1 by the value 5 C parameter lt 64 gt DeltaKSL Exceeding the maximum collector temperature parameter lt 26 gt ALARM Temp KSL causes the KSL pump P1 to be switched on in order to protect the solar collector against overheating The KSL protection has a higher priority than limiting the BUF temperature The control unit realizes the after season rundown of the pump by switching it on for 1 min if it doesn t operate for a week 2 4CH pump operation P3 If the buffer temperature exceeds the preset value of 45 C the lt 31 gt Switch on Temp of PUMPS parameter the CH pump turns on The control unit protects the system from freezing automatically turning on the circulating pump if the measured temperature is below 4 C The control unit realizes the after season rundown of the pump by switching it on for min if it doesn t operate for a week 2 5 Summer mode CH You can select ModeCH SUMMER setting in which the CH pump doesn t run Pi SUMMER Turning off the heating system in summer time the CH pump doesn t operate Fireplace only works in the function of loading the BUF buffer HE Pa ON standard operation 2 6 CONTROL output The control unit is equipped with the CONTROL relay wh
10. f the pumps It prevents from often switchovers especially if there s another heat source in the heating system 61 DeltaBUF 10 10 C 1 C Minimal temperature difference between fireplace and buffer required for the BUF pump P2 to run Negative values have application for big buffers with the temperature sensor mounted in the upper zone
11. g up to 8 secs do not interrupt its operation over the time the emergency buffering power source is activated 1 Basic technical parameters Power Power consumption without load Max connection power Operation conditions Housing protection class Fuse Number of outputs to control pumps Number of nonvoltage outputs Number of outputs to control the air damper drive Number of water temperature sensors Temperature measurement precision Temperature measurement resolution 230V S50Hz 5W 750W 0 50 C humidity 10 90 no condensation IP41 6 3A 250V 3 250W 230V 50Hz l 1 5V 500mA DC 3 PT1000 50 200 C 2C 0 5 C 2 Principle of Operation E The main function of the control unit is to keep temperature in the water jacket at the preset value The task is realized by measuring temperature T3 and controlling the cold air choke valve PP properly Fireplace operation temperature is defined by the lt 20 gt FIREPLACE Temp parameter see PARAMETERS LEVEL 1 If the fireplace temperature T3 is higher than the lt 20 gt FIREPLACE Temp parameter the choke valve is gradually shut off limiting air supply and if the temperature T3 1s lower than the lt 20 gt FIREPLACE Temp parameter the choke valve is gradually opened up The second function is control the loading pump of the BUF container P2 The pump P2 runs if the fireplace temperature exceeds BUFF ON and is above the buffer
12. ng The changed parameter not confirmed for 10 secs is not accepted by the control unit and it recalls a previous value of the parameter The button F2 ESC 8 is for cancelling a current operation and going over to the screen of the fireplace ON OFF SO Vv 7 6 CONFIRM CHOOSE Q Q Q Q 8 Fig 2 Control panel view WARRANTY 1 Warranty is valid 24 months from the date of sale 2 Producer does not take responsibility for any mechanical damages made by user 3 MAKING REPAIRS OR MODYFYING THE DEVICE BY USER IS FORBIDDEN AND CAUSES WARRANTY CANCELATION 4 Warranty card is valid only with date of sale seller s signature and stamp 5 Warranty and after warranty repairs should be done only by producer damaged regulators should be sent to producer in order to make all repairs needed 6 Warranty protection includes the EU 7 Warranty does not exclude not restrict and not suspend buyer s rights coming from the incompatibility of the article with the agreement Laws Journal No 141 Pos 1176 WARNING ANY MODIFICATION OF THE CONTROL UNIT MADE BY A USER CAN BE THE CAUSE OF SAFETY CONDITIONS DETERIORATION AND CAN EXPOSE THE USER TO ELECTRIC SHOCK OR DAMAGE DEVICES SUPPLIED Connection cable of the control may be replaced only by producer or his authorized service locations WARNING 1 Producer does not take the responsibility for damage caused by atmospheri
13. ole responsibility that the following product the control unit of the heating system with the fireplace controlled by the air damper model RT 08G BUF SOLAR is in conformity with the basic requirements included in Directive EMC 2004 108 WE of 15 12 2004 the electromagnetic compatibility law of 13 04 07 and Directive LVD 2006 95 WE of 21 08 07 Laws Journal of 2007 No 155 pos 1098 regarding the requirements for electric devices To the conformity evaluation the following harmonized standards were used PN EN 60730 2 1 2002 Automatic electric control units for house usage and the like Part 2 1 Specific requirements regarding electric control units for electric house devices Automatic electric control units for house usage and the like Part 1 General requirements PN EN 60730 1 2002 PN EN 55022 2000 Electromagnetic compatibility EMC IT devices Characteristics of radioelectric noises Acceptable levels and measurement methods Complementary information Laboratory IASE 51 618 Wroclaw 1 Wystawowa st Test report No 39 DL I 07 of 22 06 2007 41 DL 1 07 of 03 07 2007 Electronic Engineering Plant TATAREK has initiated management system and complies with the following standard 1SO9001 2000 CERTIFICATE No 133 2004 of 01 2004 Polish Foreign Trade Chamber The last two digits of the year in which the CE marking was affixed 07 Place of issue Manufacturer representative Wroclaw Mirostaw Zasepa Case Date of is
14. ose contacts can be used e g to switch off another heat source when the fireplace works The lt 12 gt CONTROL Relay parameter defines the function of the relay more precisely see PARAMETERS LEVEL 3 a CONTROL relay turned off REL a 1 CONTROL relay turned on 3 Service of the control unit There are elements on the control panel fig 2 In the turn off state only the orange stanby state LED 7 lights and the graphic display shows current temperature of the water jacket and current time The turn on ofthe control unit follows by pressing the button 3 ON OFF In order to turn it off press once more the button 3 and at the same time hold it down for about Isec In case of supply voltage decline the control unit comes back to the state before the decline The operation state 1s presented on the graphic display 2 The screens inform about the operation of devices temperature of sensors they make it possible to change the parameters etc The change of screen is done by pressing the CHOOSE button 7 If this is the screen that is able to change a parameter press the CONFIRM button 6 which causes blinking of the parameter field to be changed By pressing 4 or 5 one can alter its value If there are more parameter fields on the screen e g setting the clock then one will go among them by pressing the CHOOSE button 7 By clicking the CONFIRM button 6 one confirms the changes the parameter field stops blinki
15. parameters are possible only at unlocked password To unlock the password you need to input proper sequence of digits with the buttons With the CHOOSE button 7 to change the digits position and CONFIRM button 6 to acknowledge all and finish the procedure of changing the password The unlocked password is set to 0000 Once again entering into the password change procedure causes a new password to be set PASSWORD 9999 HAS CONSIDERABLE MEANING IT CAUSES THE REACTIVATION OF THE PREVIOUS PASSWORD IF PRESENT WITHOUT IT BEING EXPOSED PASSWORD OF PRODUCER S SERVICE IS UNIQUE AND IS NOT DEPENDENT ON THE USER S PASSWORD IT SHOUDN T BE EXPOSED TO THE USER INSTEAD OF THAT THE SERVICE CAN SET THE USER HIS OWN PASSWORD Examples of passwords 1 The control unit is installed with the unlocked password The user can enter his own password e g 1234 From this moment the important parameters cannot be altered without the password being unlocked that is resetting the password 1234 After changing essential parameters the user can leave the control unit unlocked set any new password or enter 9999 which activates the password 1234 2 Producer gives the control unit with the set password The user cannot alter the important parameters The servic can change the settings with its own secret password At the end a serviceman enter the secret password or 9999 the user still hasn t access to the important pa
16. rameters 3 Producer gives the control unit with the set password The user cannot alter the important parameters The servic can change the settings with its own secret password At the end a serviceman leaves the control unit unlocked the user now has access to the important parameters He can enter his own password like in example No 1 4 Producer gives the control unit with the set password The user cannot alter the important parameters The servic can change the settings with its own secret password At the end a serviceman sets the password e g 1234 and tells it to the user the user has access to the important parameters but without knowing the password the other persons cannot make the changes 5 The user has the unlocked control unit or his own password Serviceman decides the user though oughtn t have access to the important parameters The serviceman locks the control unit with his secret password which removes the user s password and locks the control unit 6 Serviceman doesn t have to know the user s password Always he can use his own secret password and at the end lock with the 9999 which reactivates the user s password Demonstration change of the lt 50 gt ChokeV State OFF parameter defining the choke valve position after powering off the control unit Parameters level 3 Press Repeatedly the button CHOOSE till the PARAMETERS LEVEL parameter setting screen appears Button CONFIRM gt 0
17. rol Temp unit Minimal temperature of the buffer at which the CH pump P3 can be activated temp ON the buffer pump P2 BUF can be activated 10 Signal OFF ON ON OFF turns off sound signal ON ALARM ON turns on sound signal ALARM ON ALARM turns on sound and alarm 31 Switch on Temp 30 75 C 11 Language Eneligh j Polish Selection of the language version Deutsch 13 OFF backlight is active for 2mins from the last pressing LCD backlight OFF ON OFF of the button ON backlight is active when the control unit is switched on Turning off the backlight means it equals to lt 15 gt next 15 Minimal backlight level of the LCD it s vital with negative LCD backlight 0 25 10 LCD The value 0 means a full turn off PARAMETERS LEVEL 2 No Po FUNCTION sd NCTION a a f Zonel from Start of the Ist time zone tla I ei 7 Zonea trom a 1400 Starter the 2ndvime zone 7 E 00 28 a entefeanatinesame ee eee P zonese MAT FHT E ECO4 from 23 00 a Start of the 4th time zone economic 5 5 79 ECO5 to eal 13 30 End of the 5th time zone economic PARAMETERS LEVEL 3 PARAMETERS CAN BE CHANGED AT THE UNLOCKED PASSWORD 50 ChokeV 0 100 0 Position of the choke valve in the power supply state State OFF turned off 0 full shut off 100 full opening 33 Hysteresis 1 10 C 1 C Temperature hysteresis of turning on off the pumps CH WAW of PUMPS The temperature difference between turning on and turning of
18. sue Position 08 2007 Konstruktor 2 1 Air damper operation The air damper regulates an air supply to the combustion chamber which allows the temperature of the fireplace water jacket to be kept at the preset value The task is realized by comparing the temperature of the water jacket T3 and preset temperature the lt 20 gt FIREPLACE Temp parameter and then by gradual opening shutting the air damper The change of the air damper position is done every 20secs The shutdown of the control unit automatically causes the air damper to be set at the rest position defined by the lt 50 gt ChokeV State OFF parameter Default setting is 0 full shut off 2 2 Operation of the loading pump of the buffer P2 The control unit controls the pump loading the buffer The BUF pump P2 can be switched on if water temperature in the fireplace is above the preset threshold 48 C parameter lt 60 gt PumpBUFtemp ON and higher than temperature in the container by 1 C parameter lt 61 gt DeltaBUF Turning off the pump below the parameter lt 60 gt PumpBUFtemp ON causes a faster heating of the water jacket above the dew point and as a result the longer life time of the fireplace After the loading the BUF pump still runs for 1min parameter lt 63 gt RundownTimeBUF The control unit protects the system from freezing automatically turning on the circulating pump if the measured temperature is below 4 C The control unit realizes the aft
19. ter existing for 30mins is treated as a burnout of the fireplace The control unit ends the operation cycle setting the air damper to the rest position Pressing the ON OFF button 3 once more starts another operation cycle The green status diode 1 lights during the fireplace operation and goes out after recognizing the burnout state of the fireplace AUTO operation icon in waiting for the start of a new cycle that is before its start or after ts end AUTO operation icon during the cycle It s a stable state that is in order to change it you need to press the CHOOSE button Operation screen of the whole system It s astable state that is in order to change it you need to press the CHOOSE button KSL pump Temperature of the PONS 4 water jacket T3 KSL temperature T2 o te Relay CONTROL Operation mode of the CH pump BUF pump BUF temperature CH pump doesn t runs T1 run Screen of pumps operation for the basic operation configuration Screen of the operation modes _ enables changing the operation mode of the fireplace and WAW container Possible operation modes ofthe fireplace are as follows described above MAN OFF AUTO ON Possible operation modes of the WAW container are as follows described above SUMMER ON H Keresana EE current mode z MAN 5
20. the fireplace the lt 20 gt FIREPLACE Temp parameter After pressing the CONFIRM button 6 the preset temperature blinks whose value can be altered with the buttons 4 or 5 To confirm the changes you need to press the CONFIRM button 6 once more Ifthe manual mode is set FIREPLACE MODE MAN the green LED diode 7 blinks you can manually control the air damper The button 4 causes the opening of the air damper one step 10 and the button 5 causes its closing There are the following operation modes of the fireplace MAN Automatic control locked only manual control of the air damper is available Green status diode 1 blinks OFF Setting the air damper to the rest position the lt 50 gt ChokeV State OFF parameter Green status diode 1 doesn t light AUTO Full automatic burning cycle in the fireplace firing up operation burning out Automatic operation is controlled by pressing the button 3 ON OFF Green status diode 1 lights during the fireplace operation and goes out when the burnt out state is detected At the end of the burning out phase the air damper sets to the rest position 0 full shut off which prevents a room from cooling off and protects the water attachment against freezing ON The air damper is automatically controlled to stabilize temperature of the water jacket Green status diode 1 does light 6 Password The changes of important
Download Pdf Manuals
Related Search
WARNING!!! warning letter warning sign warning labels warning emoji warning light warning synonym warning symbol warning sticker warning icon warning signs of dementia warning letter format warning in spanish translation warning order warning sign emoji warning letter to employee warning triangle warning signs of a stroke warning vs watch warning png warning band warning letter fda warning green day warning icon png warning signs of heart attack for women warning zone