Operation Manual - Bestlink Netware
Contents
1. the pick up device It is recommended that the pick up device surface be cleaned before lens installation or whenever the lens is changed Cleaning should be done by using a chamois a very fine soft cloth lens tissue or cotton tipped applicator and ethanol to carefully remove any fingerprint or dust 5 Check the power source voltage The power source voltage should be within the specified range Camera must meet the specifications Camera must be connected to a surge protector at all times 6 Objects and liquid entry Never push objects of any kind into this camera as this may touch dangerous voltage points of short out parts that could result in a fire or electric shock Never spill any kind of liquid on the video product 7 Servicing Do not attempt to service this video product by yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all service to qualified servicing personnel 8 Damage requiring service Unplug this video product from the wall outlet and refer service to qualified servicing personnel under the following conditions a When the power supply cord or plug is damaged b If liquid has been spilled or objects have fallen into the video product c If the video product has been exposed to rain or water d If the video product has been dropped or the cabinet has been damaged e When the video product exhibits a distinct change in performance A OK I USA products are c2. SST 7420 SST 7420P Operational Manual Standard Box Color Camera Please read the Operational Manual before attempting to use this product E FEATURES 1 3 Sony Super HAD CCD 420 TV Lines 0 2 Lux F1 2 3 Lead Pb Free RoHS Compliance i Long life and high reliability are achieved by the use of CCD imaging device This makes the camera 100 1 Lens mount solid state This mount is used to install a CS mount lens r 12V DC 24V AC CS adaptor ring is required if use a C mount lens 2 Camera mounting screw holes Screw hole for fixing camera 3 Mount Adaptor This adaptor can be attached to either the top or bottom of the unit 4 Auto Iris Lens Connector 4 pin type The lens connector supplies the auto iris lens not supplied with DC power and a video signal or DC control signal PINNO VIDEO DC 12V CONTROL CONTROL VIDEO SIGNAL DRIVE O 4 O DRIVE 5 Control Switch SW1 SYNC MODE SYNC Mode Selection INT L L switch SW2 AES Automatic Electronic Shutter OFF AES switch SW3 BLC Back Light Compensation OFF BLC switch SW4 F L Flickerless NOM F L switch SW5 AGC Automatic Gain Control OFF AGC switch o f R 6 VI DEO connector hamdi time Bi This is an output for connection to a video monitor etc 7592 i 7 Iris mode selection switch Used to choose DC or VIDEO mode according to the type of your lens 8 DC Level adjustment V R Used to adjust video output level
3. aK BOn ON OFF Switchable Compensation Auto Gain Control S N Ratio Electronic Shutter Speed ON OFF Switchable ON OFF Switchable CS C with Adaptor DC Video Switchable 12V DC 24V AC 145mA 1 7W Lens Mount Auto I ris Control Power Consumption Operation Temperature Operation Humidity Storage Temperature 14 F 122 F 10 C 50 C RH 85 or less 49 F 140 F 20 C 60 C 2 36 W x 1 97 H x 4 69 L 60mm W x 50mm H x 119mm L 0 88lbs 400g Specifications are subject to change without notice LIST OF COMPONENTS One 1 SST 7420 SST 7420P Camera One 1 Allen Wrench One 1 CS Adaptor Ring One 1 Operational Manual For any returns please include all components listed above with original packaging in Resalable Condition Absolutely No Returns will be accepted if any component is missing damaged or if any cable is cut or tampered with A Co 1 Never point the camera toward the sun Do not expose the lens directly to the sun or to strong light as this may damage the pick up device 2 Handle this camera with care Avoid any shock or bumping of the camera Improper handling could damage the camera 3 Requires a proper operating environment This camera is designed for indoor use The allowable temperature range for operation of this camera is between 14 F 122 F 10 C 50 C and the allowable humidity is 85 RH maximum 4 Clean the front face to
4. of DC driven auto iris lens 9 Power input terminal Connect the power supply of 12V DC 24V AC amp O 00 CONTROL SWITCH OPERATION 9 b ney SW1 SYNC MODE INT MODE The camera may be operated independently with its internal crystal control L L MODE This version w o L L function SW2 AES AES The automatic electronic shutter control 1 60 1 50 1 100 000 sec is employed for using a manual Iris Lens m SW3 Example of Back Light Compensation When the object is dark by strong light sun illumination etc as Fig 3 1 Please turn tda m on BLC switch The object becomes as Fig 3 2 SST 7420_rev09032008 FE CE AES ON Pm BLC OFF 1 INT E oL OFF e E AES OFF OE aic wow HE FL OFF EE acc AES OW fp BLE ON Fig3 2 SW4 F L Flickerless F L Fixes shutter speed at NTSC 1 100 Sec PAL 1 120 Sec When using this switch set AES OFF NOM Normal position SW5 AGC AGC level varies from 0 to 26dB OFF AGC level is fixed at 0 dB SPECI FI CATIONS SST 7420 SST 7420P TV System NTSC PAL 1 3 Sony Super HAD CCD Total Pixels 537 H x 505 V 537 H x 597 V Video Output 1 0Vp p Composite 75 ohms Resolution 420 TV Lines I mage Sensor 0 2 Lux F1 2 AES ON AES ON 1 60 1 100 000sec 1 50 1 100 000sec AES OFF 1 60sec AES OFF 1 50sec Synchronization Internal P
5. overed under warranty for one year from the date of purchase The warranty will automatically be voided if any of the following occurs 1 Camera sticker is removed If the camera sticker is removed we will not be able to confirm any information regarding when and where the product was purchased We have no other way to verify the purchase record without the serial number on the camera sticker therefore it should not be removed 2 Camera is modified in any way If the camera is scratched damaged or modified in a manner not described in this manual the warranty will be voided immediately It is the customer s responsibility to keep the camera in good condition 3 Video or power cable is cut The video cable and the power cable should not be tampered with Cutting or modifying of the cables will result in termination of the warranty SST 7420_rev09032008
Download Pdf Manuals
Related Search