Home

inno racks in-sr roof rack installation instructions manual

1. Failure to do so may cause the sunroof hatch gate or rear spoiler to hit the carrier and or cargo Do not concentrate the cargo in one area Doing so may damage the carrier and or cargo Care and Storage Other manufacturer s attachment 4 While other companies attachments may fit our crossbars we can only guarantee the safe performance of our rack when used with RV Inno attachments 2 After cleaning carrier check for any of the following 1 Worn screw threads 2 Key deformation 3 Holder deformation 4 Cracks in any of the components of the carrier system B When using the Carrier System avoid driving at excessively high speeds Do not make hard starts unnecessarily sharp turns abrupt maneuvers or emergency braking In case you have to perform such a maneuver always check afterwards to see that the carrier system and cargo remain secure Always check to see that the carrier and cargo are secured in place after driving continuously at high speeds in adverse weather conditions or when driving over rough roads Check the fastening knobs and bolts width adjustment screws and any other mounting hardware on a periodic basis to see that they are securely tightened Always remove the carrier system before running your car through a car wash Mount the carrier system to your vehicle in al a well lit open space on flat stable ground Store all components of the carrier system together in one p
2. IN SR LowDown Stay Installation Instructions RV INNO The IN SR Stays include the parts shown below Verify that all of these parts are included in the package you have purchased In the event any of these parts is missing contact ORS RACKS DIRECT 1 800 894 7547 Other parts such as bars and attachments are sold seperately unless you are buying a complete system Key A A Q eelef and place holder on washer 3 Hook holder onto barrel nut on stay Slide notch of holder over bolt Assemble all 4 stays in the same way Barrel Nut Hook Holder D Slide stay over bar and remove bolt from holder ann Bar T Slide notch of holder over bolt and place holder on washer Washer For some vehicles with fatter rails y it may be necessary to completely remove knob and washer and reinstall them once bolt is positioned in notch of holder Roof rail Clean the roof of your car to remove any dirt or debris Release lock with key and remove lock cover Slide washer over stay bolt and loosely tighten knob until bolt end extends 2 3mm past end of bolt Let bolt end project 2 to 3 mm 0 1 Mounting the Carrier on the Car Place bars on right and left roof rails perpendicular to moving direction of car The side of the bar with the 8 grooves should face N CAUTION 700 mm 27 6 or more aa Set distance between front and rear bars to 700 mm 27 6 or more whenever DERA possib
3. If key doesn t lock check the following and securely Bo KS Before driving the vehicle rock the stays and bars in the all directions to ensure that there is no looseness SF in any of the mounting knobs Retighten any loose knobs Is knob preventing cover from sliding on all the way Is holder contacting lock cover F When mounting attachments stradling the stays attach one of the included rubber pads on the contact surface of the stay for protection AN CAUTION Boat amp canoe attachments cannot be installed 1 Lock Cover Incl 2 keys Genuine RV Inno Replacement P arts 1SP133 The following genuine replacement parts are available for this RV Inno carrier system component Specify the part number when ordering parts from your dealer eee jey for number Specifications and appearance of the carrier system and genuine replacement parts are subject to change without prior notice in the interest of product improvement SR Stay Assembly Incl 2 keys ISP909 lt gt rubber Pads 4 y Knob and washer set ISP132 i ISP 503 UsER s EN JEJ srana a Contact Information If you have any comments or suggestions please contact ORS RACKS DIRECT www orsracksdirect com 1 800 894 7547 ORS Racks Direct shall not be held liable for any accidents or incidental losses arising from improper installation or use nor for those arising from installation or use after the customer has made any change to the sy
4. lace to prevent any component from being lost Avoid storage in areas subject to direct sunlight high temperature or excessive humidity
5. le Minimum safe spread is 600mm 23 6 2 j Be Rest stay on rail Holder should be positioned under rail A caution Stay bolt should face outer side of car Holder AX carrion Hook cover must contact roof rail Outer side of car gt B While pressing stay down onto roof rail lift holder until it is parallel with either the bottom of roof rail or bar If roof rail has round bottom holder should be parallel to bar While lifting holder tighten the 2 barrel nut bolts alternately with hex wrench to adjust holder angle Loosely tighten knob Hex wrench Barrel nut bolts Barrel nut bolts Barrel nut bolts Barrel nut A caution Confirm that holder is securely engaged on barrel nut Must be uniform Parallel Align centers of holder and stay Tighten knob f Lock cover cannot be installed if cie 5 aa bolt end is not projecting from Misaligned holder and stay may prevent installation of lock cover 7A knob Lower barreknutwith hax Stay l Stay IN wrench and tighten knob further Lock cover won t fit properly due to knob Roof rail Roof rail R Holder Holder center ers Stay center Install bar end caps on both ends of bar End cap If lock cover doesn t fit properly check knob or holder position Lock key Check to make sure that carrier system is installed properly
6. stem s original configuration or specifications CARMATE Guidelines for Using the Carrier System Before using your new Carrier System carefully read these guidelines as well as the installation and usage instructions for all the components that make up the your system After reading these guidelines keep them in a safe place with the instructions for the rest of the system If you have any questions regarding the information in this manual please contact the service center listed in the installation instructions A Precautions 1 Wash any mud off the carrier system Use a damp towel to wipe away dust and dirt Do not use any thinner or solvents to clean any part of the carrier system use only mild soap or detergent if necessary The carrier system s compatibility with an automobile is determined by the type of stay used Certain vehicles require the use of a carrier base and mounting hooks Be sure to consult the FIT GUIDE which is available at your dealer or online The mounting position loadable cargo and maximum carrier capacity vary by vehicle type Be sure to read Mounting Methods by Vehicle Type in the Installation Instructions for the Mounting Hooks Do not attempt to modify the carrier system Always use the key lock to secure the carrier WR The locks are an extra safety measure preventing the racks from coming loose Exercise caution when opening or closing the sunroof hatch or tailgate

inno racks in-sr roof rack installation instructions manual

Contents

Download Pdf Manuals

Related Search

Related Contents