Owner`s Manual
Contents
1. 4x4 POWER DISTRIBUTION UNIT Operation Manual PB 4X4 FRONT SP 4X4 FRONT POWER INPUT VOLTAGE sp 4x4 STEED Se CAT ETER STATION Ps 4x4 TEE piah CAT eT BACK ALL UNITS ak BAAS LUA LEA WA THE TLETS 1 TOVA 154 1600 WATT INTRODUCTION We congratulate you on choosing an ART 4x4 Power Distribution Unit You will find that they have been designed for easy use The latest advances in power technology have been utilized in the design of these units Please read all instructions carefully before operating All 4X4 Models Power Base Smart Power and Power Station Feature e Front Mounted Circuit Breaker Reset Switch e Surge amp Spike Protection e EMI amp RFI Filtering e Unique 4X Distribution on the Back Four of the Eight Rear Switched Outputs are wider for Wall Wart Devices e Total Power Capacity of 1800 watts e Rugged All Steel Chassis Occupies 1u Rack Space Smart Power SP adds e 2 Front Shock Mounted Light Posts e Backlit Linear Meter to Monitor Input Voltage e Separate On Off Light Switch e Adjustable Dimmer Dial Power Station PS has all SP features and adds e Backlit Ammeter to Monitor Load Current The 4x4 POWER DISTRIBUTION UNITs protect your delicate electronic equipment with a high voltage varistor MOV surge and transient suppressor The fast acting suppression circuit responds in less than a nanosecond clamping transient voltages to safe levels OPERATION2. MAXIMUM LOAD The eight circuit breaker protected outlets are rated at 15 amps which is equivalent to 1800 watts at 120 volts If the total load on the 4x4 POWER DISTRIBUTION UNIT s outlets and rack lights on the SP amp PS exceed 15 amps the circuit breaker will trip cutting off power to your rack If this happens reduce the load by unplugging one or more units from the 4X4 POWER DISTRIBUTION UNIT Then push the circuit breaker button in to reset it LAMPS SP amp PS The 4x4 POWER DISTRIBUTION UNIT s lamps pull out easily and may be aimed to provide the best illumination for your equipment Each lamp is supplied with a 7 watt night light bulb Replacements are readily available at most hardware stores or wherever household light bulbs are sold Adjust the DIMMER control for the desired brightness The lights do not turn off automatically when the tubes are pushed in so be sure to switch the RACK LIGHTS switch to the OFF position before pushing in the tubes CAUTION BURN WARNING The caps and light tubes become hot during normal operation Avoid burning your fingers by allowing the cap to cool completely before unscrewing it Do not push the tubes in while the caps are unscrewed If you find that the heat from the tubes is excessive reduce the setting of the Dimmer control or substitute a 4 Watt bulb BULB REPLACEMENT SP amp PS Bulbs are easily replaced without removing the unit from the rack Simply unscrew the cap on the end of each
3. a valid sales receipt EXCLUSIONS This warranty does not apply in the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs This warranty is void if the serial number is altered defaced or removed A R T reserves the right to make changes in design and make additions or improvements upon this product without any obligation to install the same on products previously manufactured A R T should not be liable for any consequential damages including without limitation damages resulting from the loss of use Some states do not allow limitation of incidental or consequential damages so the above limitation or exclusion may not apply to you This warranty gives you specific rights and you may also have other rights which vary from state to state For products purchased outside the United States service will be provided by an authorized distributor of Applied Research and Technology products SERVICE The following information is provided in the unlikely event that your unit requires service Use this procedure to return units in the United States only For service outside the United States please contact your authorized A RT distributor 1 Be sure the unit is the cause of the problem Check to make sure the unit has power supplied all cables are connected correctly and the cables themselves are in working condition 2 If you find the unit to be at fault write down a description of the problem includ
4. ing how and when the problem occurs 3 Contact our Customer Service department at 716 297 2920 for your Return Authorization number or questions regarding your repair Customer Service hours are Monday through Friday 9 00AM to 5 00PM Eastern time A Pack the unit in its original carton or reasonable substitute The packing box is not recommended for a shipping carton Put the packaged unit in another box for shipping Print the RA number clearly under the address 5 Include with your unit a return shipping address we cannot ship to a P O Box a copy of your purchase receipt a daytime phone number and the description of the problem 6 Ship the unit to Applied Research and Technology a Division of Yorkville Sound Inc 4625 Witmer Industrial Estates Nigara Falls NY 14305 Attn Repair Department RA
5. light tube remove the old bulb and replace POWER SWITCHES The 4x4 POWER DISTRIBUTION UNIT has a master POWER switch for the rear outlets as well as the lights SP amp PS This switch glows when the unit is on Warnings 1 All operating instructions should be read before using this equipment To prevent the risk of electrical shock do not remove the cover or the back There are no user serviceable parts inside Please refer servicing to a qualified service technician Do not expose this unit to heat sources such as radiators stoves or other items that generate excessive heat This unit should be cleaned only with a damp cloth audio solvents or cleaning detergents Do not get moisture inside the unit When moving this equipment it should be placed in its original carton and packing to reduce the risk of damage in transit de all WARRANTY AND SERVICE INFORMATION Limited Warranty Applied Research and Technology will provide warranty service for this unit in accordance with the following warranty statement Applied Research and Technology A R T warrants to the original purchaser that this product is free from defects in workmanship and materials for a period of one year from the date of purchase A R T will without charge repair or replace at its option defective product or component parts upon prepaid delivery to the factory service department or an authorized service center accompanied by proof of purchase date in the form of
Download Pdf Manuals
Related Search