Let`s go
Contents
1. 1 Open the SIM or USIM card cover NOTE Do not remove the cover rudely because it is connected with the device x w gt i 2 Install a SIM or USIM card to the SIM or USIM card slot The following figure shows the correct installation direction You will hear a click when the SIM or USIM card is locked in place IMPORTANT Your device does not support the Micro Nano SIM card or any other nonstandard SIM cards To avoid damaging the device do not use those cards or any card holders 3 Close the SIM or USIM card cover 6 Connecting Your Device Using Wi Fi 1 Power on your device 2 Use the Wi Fi application on a client to search for available wireless networks Bx g Disable p View Available Wireless Networks Status Repair Bridge Connections Create Shortcut Delete Rename Properties NOTE Set the client to obtain an IP address automatically For the detailed procedure refer to Configuring Your PC The client gets an IP address for example 192 168 0 101 3 Select the SSID of your device and then click Connect NOTE You can find the default SSID on the label of your device 4 Enter the password and then click Connect Wireless Network Connection xi The network uFi_XXXXXX requires a network key also called a WEP key or WPA Key A network key helps prevent unknown intruders from connecting to this network Type the key and then dick Conn2. ZTE MF910 Let s go Getting Started With Your Device ZTE CORPORATION NO 55 Hi tech Road South ShenZhen P R China Postcode 518057 LEGAL INFORMATION Copyright 2014 ZTE CORPORATION All rights reserved No part of this publication may be excerpted reproduced translated or utilized in any form or by any means electronic or mechanical including photocopying and microfilm without the prior written permission of ZTE Corporation The manual is published by ZTE Corporation We reserve the right to make modifications on print errors or update specifications without prior notice Version No R1 0 Edition Time June 10 2014 Manual No 079584506591 NOTE Do not use the device in an enclosed environment or where heat dissipation is poor Prolonged work in such space may cause excessive heat and raise ambient temperature which may lead to automatic shutdown of the device for your safety In the case of such event cool the device in a well ventilated place before turning on for normal use 2 Getting to Know Your Device Appearance The following figure is for your reference only ss SIM or USIM Card Cover Reset Button WPS Button Power Button LCD Screen Charger USB port AUX Antenna Connector Main Antenna Connector NOTES Press and hold the Power button for about 10 to 15 seconds to restart the device Ifthe battery is extremely low you may be unable to power on the device even when it i
3. ch as the electronic system of vehicles Consult the manufacturers of such devices before using the device if necessary Operating the device may interfere with medical instruments such as hearing aids and pacemakers Always keep the device more than 20 centimeters away from such medical instruments when your device is turned on Turn the device off if necessary Consult a physician or the manufacturers of medical instruments before using the device if necessary Be aware of the usage limitation when using the device at places such as oil warehouses or chemical factories where there are explosive gases or explosive products being processed Turn off the device if necessary Do not use electronic transmission devices in aircrafts at petrol stations or in hospitals Observe and obey all warning signs and turn off the device in these conditions Do not touch the inner antenna area unless it is necessary Otherwise the performance of the device may be affected Keep the device out of the reach of little children The device may cause an injury if used as a toy When the device is operating do not touch the metallic parts Failing to do so may cause burns Using Your Device Use original accessories or accessories that are authorized Using any unauthorized accessories may affect the performance of the device and violate the related national regulations about telecom terminals Avoid using the device near or inside metallic structures or
4. ct or return the product or receive a refund for the product from ZTE under the above mentioned situations 16 e This warranty is end users sole remedy and ZTE s sole liability for defective or nonconforming items and is in lieu of all other warranties expressed implied or statutory including but not limited to the implied warranties of merchantability and fitness for a particular purpose unless otherwise required under the mandatory provisions of the law Limitation of Liability ZTE shall not be liable for any loss of profits or indirect special incidental or consequential damages resulting from or arising out of or in connection with using of this product no matter whether or not ZTE had been advised knew or should have known of the possibility of such damages including but not limited to lost profits interruption of business cost of capital cost of substitute facilities or product or any downtime cost Trou bleshooting Problem Recommended Action Problem Recommended Action Ensure that your SIM or USIM m f e Install the software Run the card is available Failing to establish The client Change the location and find a a connection between your device and a PC through a USB cable installation program in the My Computer ZTEMODEM path If the driver of your device is abnormal please reinstall the software You need to uninstall the software first connected to the device cannot access the I
5. ebGUI configuration page 2 Select Settings gt Internet Wi Fi 3 Set the Internet Wi Fi Switch and Preferred Network and then click Apply 10 NOTE You need to set the Internet Wi Fi Enable and select Wi Fi Internet Wi Fi Internet Wi Fi Switch Enable Disable Preferred Network Wi Fi O WWAN Current Status WAN connected 3 Connect to the Wi Fi Hotspot There are two methods for your reference gt Input the Wi Fi Hotspot information in the Add Wi Fi Hotspot area and then click Apply gt Select this Wi Fi Hotspot which will be listed input the Pass Phrase and click Apply Add Wi Fi Hotspot Network Name SSID TP LINK_SOC Security Mode WPA PSK WPA2 PSK WPA Algorithms TKIP AES QAUTO Pass Phrase Display Password Ee Ee Security Mode WPA PSKIWPA2 PSK WPA2 PSK o DefaultAP WPA2 PSK 4 After the client connected to the Wi Fi Hotspot successfully you can access the Internet 11 Configuring Your PC The following procedure describes how to configure the Internet Protocol in the Windows operating system for your Wi Fi connection 1 Right click My Network Places and select Properties Cc Open Explore R Search for Computers Map Network Drive Disconnect Network Drive Create Shortcut Delete Rename 2 Right click Wireless Network Connection and select Properties work Connection C p GET Disable View Available Wireless Networks S
6. ect Network key ce Work ke a co NOTE You may need to enter the password for the Wi Fi connection You can view the label on your device to get the default password 5 Wait until the client is connected to your device successfully Using a USB Cable 1 Connect a client to your device through a USB cable Eiz 2 Power on your device The operating system detects and identifies new hardware and automatically finishes the installation NOTE If the system does not automatically launch installation you can run the installation program in the My Computer ZTEMODEM path 3 Wait until the client is connected to your device successfully Accessing the Internet 4G Mode After a client is successfully connected to your device you can access the Internet in Automatic or Manual mode The default mode is Automatic Mode Operation Your device is automatically connected to Automatic the Internet and you can surf the Internet through the client 1 Log in to the webGUI configuration page 2 Select Settings gt Network Settings gt Dial up Settings gt WAN Connection Manual Mode gt Manual and then click Apply 3 Select Home and then click Connect or Disconnect NOTE To modify the parameters of your device log in to the webGUI configuration page by visiting http 192 168 0 1 or http m home The default password is admin Internet Wi Fi Mode 1 Log in to the w
7. establishments that can emit electromagnetic waves because signal reception may be affected The device is not waterproof Keep the device dry and store it in a shady and cool place Do not use the device immediately after a sudden temperature change In such case dew may be generated inside and outside the device so do not use it until it becomes dry Handle the device carefully Do not drop bend or strike it Otherwise the device may be damaged Only qualified personnel can dismantle and repair the device An operating temperature between 10 C and 45 C and a humidity between 5 and 95 are recommended 15 Limited Warranty This warranty does not apply to defects or errors in the product caused by i Reasonable abrasion ii End users failure to follow ZTE s installation operation or maintenance instructions or procedures iii End users mishandling misuse negligence or improper installation disassembly storage servicing or operation of the product iv Modifications or repairs not provided by ZTE or a ZTE certified individual v Power failures surges fire flood accidents and actions of third parties or other events outside ZTE s reasonable control vi Usage of third party products or usage in conjunction with third party products if such defects are due to the combined usage Any other cause beyond the range of normal usage intended for the product vii End users have no right to reje
8. isiting www ztedevice com Calling the service hotline 86 755 26779999 C 1588 20
9. nternet place with good signal Check the setting of the WAN connection mode Contact your service provider and confirm your APN settings Failing to establish a connection between your device and a client through Wi Fi Ensure that the Wi Fi function is enabled Refresh the network list and select the correct SSID Check the IP address and ensure that your client can automatically obtain an IP address Enter the correct network key Wi Fi password when you connect the client to your device The client cannot access the Internet in AP mode Ensure that the WLAN device has already been connected to the Internet Ensure that your device and the WLAN device are in different subnets Failing to visit the webGUI configuration page Enter the correct address The default address is http 192 168 0 10r http m home Use only one network adapter in your PC Do not use any proxy server 19 Problem Recommended Action About the password For the Wi Fi connection password view the label on the device Press the WPS button and then the SSID and Wi Fi connection password are displayed on the screen The default password of the webGUI configuration page is admin If you changed the password and forgot the new password you need to restore the device to the factory default settings You can get help by Sending an E mail to mobile zte com cn V
10. s being charged In this case try again after charging the device for PN Oe Or B00 3 about 20 to 30 minutes Contact customer service if you still cannot power on the device after prolonged charging Do not change the built in rechargeable battery in your device by yourself The battery can only be changed by ZTE or ZTE authorised service provider Indicators When the device is powered on the following icons may be displayed on the LCD screen For a description of the icons refer to the following table Icon Description 36 Network signal strength Network type The 4G or 3G icon is 3G 4G displayed on the LCD screen depending on the connected network R The user is in roaming status Network in use One or more new messages are received Wi Fi status and the number of connected o users Battery power Connection Scenario The device can access the Internet in two ways and allows multiple clients to surf on the Internet at the same time The following figure is for your reference only 4G Mode A SIM or USIM card can be used to access the Internet Internet Wi Fi Mode Your device can be connected to a WLAN device such as a hotspot device or wireless router through Wi Fi to access the Internet The WLAN device must be already connected to the Internet NOTE Your device and the WLAN device must be in different subnets Installing Your Device
11. tatus Repair Bridge Connections Create Shortcut Delete Rename 12 3 Select Internet Protocol TCP IP and click Properties 4 Wireless Network Connection Properties 2 General Wireless Networks Advanced Connect using E9 Intel R PRO Wireless 3945ABG Net Configure This connection uses the following items JB Fie and Printer Sharing for Microsoft Networks al Description Transmission Control Protocol Intemet Protocol The default wide area network protocol that provides communication acios diverse interconnected networks IZ Show icon in notification area when connected I Notify me when this connection has imited or no connectivity Ok Cancel 4 Select Obtain an IP address automatically and Obtain DNS server address automatically and click OK internet Protocol TCP IP Properties aixi Gereral Atemae Corian You can get IP settings assigned automaticaly if your network supports this capabilty Otherwise you need to ask your network administrator for the sppropiate IP seting Obtain an IP address automaticaly Use the folowing IP address Obtain DNS server address automaticaly E Uze the folowing DNS sever addresses DN 13 Warning and Notice To the Owner If inadequately shielded some electronic devices may be affected by the electromagnetic interference caused by the device su
Download Pdf Manuals
Related Search