Ocean Runner
Contents
1. directly into the pump using PVC glue If the pump is set up in this way the pump head may not be less than 1 m This method of plumbing gives the best results see fig 1 capacity With all other pumps a threaded connector has to be screwed on the pressure fitting of the pump The relevant sizes are shown in Table 1 If a hard pipe is used for connecting the pumps we recommend the use of a short section of flexible hose to avoid vibration 4 Exploded parts diagram Hose connection OR 1200 OR 2500 OR 6500 Hose connection OR 3500 Fig 2 Parts List 1 motor housing 11 filter basket Hose connection for OR 1200 OR 2500 2 rotor magnet 12 lid of the filter basket and OR 6500 3 impeller 13 hose connection 1 4 ceramic shaft 14 washer 1 15 nut 5 Oring 15 nut 34 15a nut for hose connection 6 bayonet lock 16 hose connection 34 16 hose connection 7 lid of the pump housing 17 adapter nipple 34 25 mm for glueing 17 screw in adapter nipple 8 washer large 18 washer 34 18 washer 9 washer small 19 rubber sucker 4 pcs 21 O rings 2 pcs 10 rubber bearing 20 holding plate 5 Mounting The pump may be installed submerged or out of the water However it is not self priming and if set up out of the water has to be installed below the water surface level If used submerged we recommend removing the hose connection 13 on the suction side and fitting the filter basket 11 At no time should the pump b2. 0V 50 60 Hz 100V 50 60 Hz 100V 50 60 Hz 100V 50 60 Hz 25 watts 38 watts 65 watts 95 watts at 180 cm Maximum flow 1200 I h 20 I m 2500 I h 40 I m 3500 I h 58 I m _ 6500 I h 108 I m c 900 gph c 1700 gph Maximum head 3 2m 3 8m c 10 5 ft c 12 5 ft Connection pressure 34 1 side or glue joint DN25 male thread 1 114 Connection suction side male thread Protection Rating IP68 IP68 IP68 IP68 Im c 3 ft 35 C Fig 1 Operating capacity of the Ocean Runner pumps with open bore pipe Ocean Runner A pon g M o 2 lt r 2 A 0 0 1000 2000 3000 4000 5000 6000 7000 Flow l h OR 1200 1 OR 2500 2 OR 3500 3 OR 6500 4 3 Connections Suction side The suction side may be connected with flexible hose using the hose fitting 13 included As another option the male thread of the pump housing 7 can be connected to a standard PVC fitting and pipe The relevant sizes are shown in Table 1 Pressure side The pressure side can be connected with a flexible hose using the hose fitting 15 16 included This hose fitting must also to be fitted if the pump is used as a pure current pump If the pump is operated as a stand alone device the socket 17 should be glued into the pump housing using PVC glue e g Tangit OR 3500 only If the pump is used as return pump it can be directly connected to PVC pipe With the OR 3500 the socket is removed and the pipe glued
3. Operation Manual ho AQua MEDIC Magnetically coupled centrifugal pump Ocean Runner OR 1200 Ocean Runner OR 2500 Ocean Runner OR 3500 Ocean Runner OR 6500 Circulation pumps for fresh and salt water aquariums In purchasing this pump you have selected a top quality product It has been specifically developed for aquarium use and extensively tested by experts 1 Features The Ocean Runner Series of magnetically coupled centrifugal pumps are very quiet in operation They have fully encapsulated synchronous motors and can operate completely safely either submerged or out of the water The polished ceramic shaft and bearing is practically wear resistant ensuring a long operating life An integrated thermal overheat protection device prevents damage to the windings should the impeller rotation be impeded The pumps can be easily taken apart for cleaning All materials are salt water resistant CAUTION Do not operate the pump without water in the impeller chamber Do not allow the pump to remain in water which may freeze IMPORTANT NOTE Operate the pump only at the voltage shown on the product label 2 Table 1 Technical Data Model Ocean Runner Ocean Runner Ocean Runner Ocean Runner OR 1200 OR 2500 OR 3500 OR 6500 Supply requirement 230V S50Hz 230V S50Hz 230V S50Hz 230V S50Hz see label on the pump 110V 60 Hz 110V 60 Hz 110V 60 Hz 110V 60 Hz 230V 60 Hz 230V 60 Hz 230V 60 Hz 230V 60 Hz Bones consumption 10
4. and fuse If no fault is found the pump may be blocked and must be cleaned See Maintenance Cleaning above If the pump is noisy the pump head 1 to 5 has to be cleaned If the magnet or the impeller is damaged both can be changed The impeller 3 can be removed from the magnet 2 8 Warranty Should any defect in materials or workmanship be found within twelve months of the date of purchase o Aqua Medie undertakes to repair or at our option replace the defective part free of charge always provided the product has been installed correctly is used for the purpose that was intended by us is used in accordance with the operating instructions and is returned to us carriage paid Proof of Purchase is required by presentation of the original invoice or receipt indicating the dealer s name the model number and date of purchase or a Guarantee Card if appropriate This warranty may not apply if any model or production number has been altered deleted or removed unauthorised persons or organisations have executed repairs modifications or alterations or damage is caused by accident misuse or neglect We regret we are unable to accept any liability for any consequential loss Please note that the product is not defective under the terms of this Warranty where the product or any of its component parts was not originally designed and or manufactured for the market in which it is used These statements do not affect your statutor
5. e run dry The bottom plate 20 with the rubber suckers 19 can be fitted to the pump on 3 sides so the outlet positioned can be adjusted After setting up the pump ensure you can always reach the power plug Maximum depth must not exceed 1m N A B Examples of A out of water and B submerged set up Safety advice The pump is constructed for indoor aquarium use only Before working on the aquarium the power plug must be disconnected from the mains electrical supply The connection cable and the power plug must not be changed If the power cable is damaged the pump must be scrapped If the pump is used submerged the filter 11 12 or the hose connection must be used 6 Maintenance Cleaning CAUTION Disconnect the power before you start any work on the pump The pump is designed to have a low maintenance requirement and under normal conditions will be very reliable However the filter housing and all rotating parts must be cleaned regularly 1 to 5 Remove the pipe connections and undo the bayonet 6 on the pump housing Now remove the suction connection 7 Caution This part is a tight fit because it has an O ring seal and must be removed carefully so as not to break the ceramic shaft 4 The complete magnet 2 and impeller 3 assembly can now be withdrawn cleaned under running water and reassembled 7 Failures If the pump fails to operate check the power connection
6. y rights as a customer If your 40Aaua Medie product does not appear to be working correctly or still appears to be defective having followed the instructions in 6 amp 7 above please contact your dealer in the first instance Before calling your dealer please ensure you have read and understood the operating instructions If you have any questions your dealer cannot answer please contact us We reserve the right to make technical changes to this product 40 Aaua MEDIE 09 2002
Download Pdf Manuals
Related Search