GLPC 4645
Contents
1. Useful Information 8 Engine displacement 46 cm Maximum engine capacity 2 kW Bar length 43 cm Cutter rail length 18 45 cm Chain pitch 0 325 8 255 mm Chain thickness 0 058 1 47 mm Idling speed 3600 rom Maximum speed with cutting equipment 10000 rom Tank capacity 550 mi Oil tank capacity 260 ml Anti vibration function Yes Chain wheel teeth 7 6 255 mm Chain brake Yes Clutch Yes Automatic chain lubrication Yes Low kickback chain Yes Net weight without chain and chain bar 5 5 kg Net weight dry 7 kg LpA sound pressure level 104 dB A LWA sound power level 116 dB A Vibration a front handle max 5 99 m s Vibration a rear handle max 7 54 m s Chain type Carlton K2L BL 72E Bar type POH18 58SH Spark plug LDL7T Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support wwweinhell uk co uk Model Number 5336 Storage Caution Never put a chain saw into storage for longer than 30 days without carrying out the following steps Storing a chain saw Storing a chain saw for longer than 30 days requires storage maintenance Unless the storage instructions are followed fuel remaining in the carburettor will evaporate leaving gum like deposits This could lead to difficult starting and result in costly repairs 1 Remove the fuel tank cap slowly to release any pressure in tank Carefully drain the fuel tank 2 Start the en2. Kickback safety precautions Warning Kickback can lead to dangerous loss of control of the chain saw and result in serious or fatal injury to the saw operator or to anyone standing close by Always be alert Rotational kickback and pinch kickback are major chain saw operational dangers and the leading cause of most accidents KICKBACK may occur when the NOSE or TIP of the guide bar touches an object or when wood closes in and pinches the saw chain in the cut Tip contact in some cases May cause a lightning fast reverse reaction kicking the guide bar up and back toward the operator PINCHING the saw chain along the BOTTOM of the guide bar may PULL the saw forward away from the operator PINCHING the saw chain along the TOP of the guide bar may PUSH the guide bar rapidly back toward the operator Any of these reactions may cause you to lose control of the saw which could result in serious personal injury Beware of the following Rotary recoil Fig 1 A Recoil distance B Recoil reaction zone Impact Jamming recoil and pulling reactions Fig 2 A Pull B Solid objects C Push To prevent pulling reactions place the wood you wish to cut against the claw stop Use the claw stop as a pivot point during cutting Fig 2 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support wwweinhell uk co uk Model Number 5336 Safety Instructions Warning When using petrol tools basic safety pre
3. hold nose of bar in the uppermost position and tighten the bar retaining nut securely Caution A new saw chain stretches requiring adjustment after as few as 5 cuts This is normal with a new chain and the interval between future adjustments will lengthen quickly Caution If the saw chain is TOO LOOSE or TOO TAUT the drive wheel chain bar chain and crank shaft bearing will suffer premature wear Fig 12 shows the correct tension A when cold and tension B when warm Fig C shows a chain that is too loose Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support wwweinhell uk co uk Model Number 5336 Getting Started 4 Before starting the machine Chain break mechanical test Your chain saw is equipped with a Chain brake that reduces possibility of injury due to kickback The brake is activated if pressure is applied against brake lever when as in the event of kickback operator s hand strikes the lever When the brake is actuated chain movement stops abruptly Warning The purpose of the chain brake is to reduce the possibility of injury due to kickback however it cannot provide the intended measure of protection if the saw is operated carelessly Always test the chain brake before using your saw and periodically while on the job To test chain brake 1 The Chain brake is DISENGAGED chain can move when BRAKE LEVER IS PULLED BACK AND LOCKED Fig 13 2 The chain brake is ENGA
4. put chain saw down and leave area along retreat path Fig 20 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support www einhell uk co uk Model Number 5336 Limbing Limbing a tree is the process of removing the branches from a fallen tree Do not remove supporting limbs A until after the log is bucked cut into lengths Fig 24 Branches under tension should be cut from the bottom up to avoid binding the chain saw Warning Never cut tree limbs while standing on tree trunk Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support wwweinhell uk co uk Model Number 5336 Bucking Bucking is cutting a fallen log into lengths Make sure you have a good footing and stand uphill of the log when cutting on sloping ground If possible the log should be supported so that the end to be cut off is not resting on the ground If the log is supported at both ends and you must cut in the middle make a downward cut halfway through the log and then make the undercut This will prevent the log from pinching the bar and chain Be careful that the chain does not cut into the ground when bucking as this causes rapid dulling of the chain When bucking on a slope always stand on the uphill side 1 Log supported along entire length Cut from top overbuck being careful to avoid cutting into the ground Fig 25 2 Log supported on 1 end First cut from bottom underbuck 1 3 diamet
5. Perform a chain brake test prior to initial cutting following extensive cutting and definitely following any Chain brake service Test chain brake as follows Fig 29 1 Place saw on a clear firm flat surface 2 Start engine 3 Grasp the rear handle A with your right hand 4 With your left hand hold the front handle B not chain brake lever C firmly 5 Squeeze the throttle trigger to 1 3 throttle then immediately activate the chain brake lever C Warning Activate the chain brake slowly and deliberately Keep the chain from touching anything don t let the saw tip forward 6 Chain should stop abruptly When it does immediately release the throttle trigger Warning If chain does not stop turn engine off and take your unit to the nearest Gardenline Authorized Service Centre for service 7 Ifchain brake functions properly turn the engine off and return the chain brake to the DISENGAGED position Air filter Warning Never operate saw without the air filter Dust and dirt will be drawn into engine and damage it Keep the air filter clean The air filter must be cleaned or replaced after every 20 hours of service Cleaning the air filter Fig 30 31 1 Remove the top cover A by undoing the cover fastening screw B on the cover You can then remove the cover Fig 31 2 Lift out the air filter C Fig 32 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support www einhel
6. is evidenced by smoke or bar discoloration Ordering replacement parts Please quote the following data when ordering replacement parts Type of machine Article number of the machine Identification number of the machine Replacement part number of the part required Helpline Numbers UK 0151 649 1500 IRE 1890 946244 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 Petrol Engine Starting Procedure Check List Check Ignition Switch is on If No Then Switch on Continue With Starting Procedure If Yes If Engine Check is Cold Sufficient Check Fuel in Choke Tank Setting If No If Engine Then Fill is Cold Tank With Check Correct Choke Fuel Oil Setting Mix Continue Continue With With Starting Starting Procedure Procedure If the item still fails to start and if after trying all of the above procedures please call the help line for further assistance Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support www einhell uk co uk Model Number 5336 Ti AQ FAULT POSSIBLE CAUSES TROUBLESHOOTING Unit won t start Incorrect starting procedures Follow instructions in the or starts but will User Guide or refer to starting not run procedure check list on page 37 Incorrect carburetor mixture Have carburetor adjusted by adjustment setting an Authorise
7. 2 Pull out the choke lever B Fig 17 until it locks 3 Place the saw on a firm flat surface Hold the saw firmly as shown Pull starter rapidly 4 times Beware of the moving chain Fig 19 4 Push in the choke lever B as far as it will go Fig 17 Set the On Off switch A to On I to start the machine 6 Hold saw firmly and pull starter rapidly 6 times Engine should start Fig 18 7 Let the engine run for 10 seconds to warm up Press the throttle lever D briefly the engine will go to idling speed Fig 19 If engine failed to start repeat these instructions Important Always pull the starter cable slowly until you feel the initial resistance before you then pull it quickly to start the engine Do not allow the starter cable to whip back of its own accord Restarting a warm engine 1 Make sure the switch is in the On I position 2 Pull the starter rope rapidly 6 times The engine should start To stop engine 1 Release trigger and allow engine to return to idle speed 2 Move STOP switch down to stop engine Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 Helpline No UK Northern Ireland ON 6491500 Rep Ireland I890 946244 Web Support www einhell uk co uk Model Number 5336 Note To stop the engine in an emergency activate the chain brake and switch the ON OFF switch to Stop CO General cutting instruc
8. 2 Saw chain 12 Oiltank cap 3 Chain tensioning screw 13 Fan housing 4 Stop claw 14 Fuel tank cap 5 Chain brake lever 15 Rear handle bootstrap front hand guard 16 Chain guard 6 Front handle 17 Choke carburetor setting 7 Starter handle 18 Bar fastening nut 8 Spark plug 19 Throttle lever under the air filter cover 9 Air filter cover 10 Stop switch 20 Chain catch Installation Important Do not start the engine until the saw is fully assembled Important Wear protective gloves at all times when handling the chain Please note that the Chain brake lever front handle guard Fig 6 is supplied separately in the box Fit the chain bar To ensure that the bar and the chain are supplied with oil USE ONLY THE ORIGINAL BAR The oiling hole Fig 4 ltem A must be kept clear of dirt and any build up of residue 1 Make sure the Chain brake lever is pulled back into the DISENGAGED position Fig 5 Fig 6 2 Remove the two bar fastening nuts B from the main unit Fig 7 3 Fit the open end of the chain bar over the die bar pins F Fig 8 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support wwweinhell uk co uk Model Number 5336 Helpline No UK Northern Ireland ON 6491500 Rep Ireland I890 946244 Web Support www einhell uk co uk Model Number 5336 Helpline No UK Northern Ireland ON 6491500 Rep Ireland I890 946244 Web Support www einhell uk co uk Model Number 5336 To
9. 336 Tools for lubrication The Lube Gun is recommended for applying grease to the guide bar sprocket tip The Lube Gun is equipped with a needle nose tip which is necessary for the efficient application of grease to the sprocket tip To lubricate sprocket tip Lubrication of the sprocket tip is recommended after 10 hours of use or once a week which ever occurs first Always thoroughly clean guide bar sprocket tip before lubrication Note The saw chain does not have to be removed in order to lubricate the teeth of the chain bar Lubrication is possible during work with the engine switched off Warning Wear heavy duty work gloves when handling the bar and chain 1 Set the On Off switch to Stop O 2 Clean the guide bar sprocket tip 3 Using the Lube Gun optional insert needle nose into the lubrication hole and inject grease until it appears at outside edge of sprocket tip Fig 34 4 Rotate saw chain by hand Repeat lubrication procedure until the entire sorocket tip has been greased Most guide bar problems can be prevented merely by keeping the chain saw well maintained Insufficient guide bar lubrication and operating the saw with chain that is TOO TIGHT will contribute to rapid bar wear To help minimise bar wear the following guide bar maintenance procedures are recommended Warning Always wear protective gloves during maintenance operations Do not carry out maintenance when the engine is hot Hel
10. GED the chain is locked when the brake lever is pulled forward and the mechanism Fig 14 ltem A can be seen It should not be possible to move the chain Fig 14 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support www einhell uk co uk Model Number 5336 Note The brake lever should snap into both positions If strong resistance is felt or lever does not move into either position do not use your saw Take it immediately to a professional Service Center for repair Fuel and lubrication Fuel Use regular grade unleaded fuel mixed with 25 1 custom 2 cycle engine oil for best results Mixing fuel Mix fuel with 2 cycle oil in an approved container Shake gently and ensure thorough mix Warning Never use straight fuel in your unit This will cause permanent engine damage and void the manufacturer s warranty for that product Never use a fuel mixture that has been stored for over 90 days Warning If 2 cycle lubricant is to be used it must be a premium grade oil for 2 cycle air cooled engines mixed at a 25 1 ratio Do not use any 2 cycle oil product with a recommended mixing ratio of 100 1 If insufficient lubrication is the cause of engine damage it voids the manufacturer s engine warranty for that occurrence Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support www einhell uk co uk Model Number 5336 Recommended fuels Some conventional fuels are be
11. Onall jobs performed with the saw you must always wear safety goggles to guard your eyes from flying materials objects and a sound proof helmet ear plugs or the like to protect your hearing Wear a safety helmet if there is a risk of objects falling on you from above Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support www einhell uk co uk Model Number 5336 Important Wear gloves to protect your hands Wear safety shoes to protect your feet Warning Danger QO oO A N Make sure that the chain brake is released Pull back the handle chain brake before operating 7 Noise emission complies with Directive 2000 14 EC Explanation of the pictograms for handling on the machine A safety sign is fitted to the chain saw s fan filter cover This label along with the safety instructions on these pages should be carefully read before attempting to operate this unit Important Picture 1 2 3 Warns about a dangerous method of working that must not be used Picture 4 Recommends operation for safe sawing Important 1 Beware of recoil 2 Do not hold the saw in one hand 3 Avoid contact with the tip of the rail chain return point RECOMMENDED 4 Important Hold the saw firmly with both hands Place your right hand on the rear handle and your left hand on the front handle Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336
12. R SALES SUPPORT OISI 649 I500 IB90 946 6244 www einhell uk co uk MODEL NUMBER 5336 MONTH ON SALE 09 2009 THIS BOX INCLUDES 1 x CHAIN SAW UNIT e 1 x CHAIN 1 x 2 STROKE OIL e 1 x SPANNER 1 x SOFT CARRY BAG os penne ee Contents O3 Introduction 04 General Information amp Safety Instructions 12 Assembly and Parts List 17 Getting Started 20 Features 21 Instructions 38 Other Useful Information 41 Warranty Card Packaging The unit is supplied in packaging to prevent its contents being damaged in transit This packaging is raw material and can therefore be reused or can be returned to the raw material system Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support wwweinhell uk co uk Model Number 5336 Introduction Congratulations on choosing to buy a Gardenline oroduct By doing so you now have the assurance and peace of mind that comes with purchasing a product made by one of Europe s leading manufacturers All products brought to you by Gardenline are manufactured to the highest standards of performance and safety and as part of our philosophy of customer service and satisfaction are backed by our comprehensive 3 Year Warranty Great care has gone into the manufacture of this product and it should therefore provide you with years of good service when used properly In the event of product failure within its intended use over the course of the first 3 y
13. andard references EN ISO 11681 1 EN ISO 14982 Landau Isar den 08 05 2009 Weichselgartner Genera First CE 09 Art No 45 013 93 _1 No 01019 Subject to change without notice Se ae Frank Product Management Archive File Record 4501390 42 4149210 08 Documents registrar Robert Mayn Wiesenweg 22 D 94405 Landau Isar Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 GUARANTEE CERTIFICATE Dear Customer All of our products undergo strict quality checks to ensure that they reach you in perfect condition In the unlikely event that your device develops a fault please contact our service department at the address shown on this guarantee card Of course if you would prefer to call us then we are also happy to offer our assistance under the service number printed below Please note the following terms under which guarantee claims can be made 1 These guarantee terms cover additional guarantee rights and do not affect your statutory warranty rights We do not charge you for this guarantee Our guarantee only covers problems caused by material or manufacturing defects and it is restricted to the rectification of these defects or replacement of the device Please note that our devices have not been designed for use in commercial trade or industrial applications Consequently the guarantee is invalidated if the equipment is used in commercial trade or indu
14. ate toxic exhaust fumes as soon as the engine is started Never work in enclosed rooms or in rooms with poor ventilation Note The chainsaw is designed for occasional use by home owners garden owners and campers and is for general work such as stump grubbing cutting firewood etc It is not designed for lengthy use If it is used for a lengthy period the vibrations it causes in the hands of the user may result in circulation problems Cwhite finger syndrome Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support wwweinhell uk co uk Model Number 5336 Kickback Kickback may occur when the nose or tip of the guide bar touches an object or when the wood closes in and pinches the saw chain in the cut If the bar tip contacts it may cause a lightning fast reverse reaction kicking the guide bar up and back towards the operator Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the operator Either of these reactions may cause you to loose control of the saw which could result in serious personal injury Do not rely exclusively upon the safety devices built into your saw As a chain saw user you should take several steps to keep your cutting jobs free from accident or injury 1 With a basic understanding of kickback you can reduce or eliminate the element of surprise Sudden surprise contributes to accidents 2 Keep a good firm grip on the saw with both han
15. cautions including the following should always be followed to reduce the risk of serious personal injury and or damage to the unit Read all these instructions before operating this product and save these instructions 1 DO NOT operate a chain saw with one hand Serious injury to the operator helpers bystanders or any combination of these persons may result from one handed operation A chainsaw is intended for two handed use 2 Do NOT use the saw if you are tired ill or under the influence of alcohol and or drugs 3 Use safety footwear snug fitting clothing protective gloves and eye hearing and head protection devices 4 Use caution when handling fuel Move the chainsaw at least 10 feet 3m from the fueling point before starting the engine 5 DO NOT allow other persons to be near when starting or cutting with the chain saw Keep bystanders and animals out of the work area 6 DO NOT start cutting until you have a clear work area secure footing and a planned retreat path from the falling tree 7 Keep all parts of your body away from the saw chain when the engine is running 8 Before you start the engine make sure that the saw chain is not contacting anything 9 Carry the chain saw with the engine stopped the guide bar and saw chain to the rear and the exhaust away from your body 10 NEVER use a chainsaw which is damaged incorrectly set or incompletely and loosely assembled Make sure that the chainsaw stops
16. d Service Centre Fouled spark plug Clean gap or replace plug Fuel filter plugged Replace fuel filter Chain brake is on Put Chain brake in off position Unit starts Incorrect lever position on choke Move to RUN position but engine has low power Dirty air filter Remove clean and reinstall filter Incorrect carburetor mixture Have carburetor adjusted by adjustment setting an Authorised Service Centre Engine hesitates Incorrect carburetor mixture Have carburetor adjusted by adjustment setting an Authorised Service Centre No power Incorrectly gapped spark plug Clean gap or replace plug under load Runs erratically Incorrect carburetor mixture Have carburetor adjusted by adjustment setting an Authorised Service Centre Smokes excessively Incorrect fuel mixture Use properly mixed fuel 25 1 mix Poor performance Blunt chain Sharpen or replace the chain when operated Loose chain Tension the chain Engine dies Empty petrol tank Fill up the petrol tank Fuel filter in the wrong Completely fill the petrol tank or position in the tank re position the fuel filter in the petrol tank Insufficient chain Empty oil tank for the chain Top up the oil tank for the chain lubrication the cutter rail Oil lubrication Clean the oil lubrication hole and chain get hot opening blocked in the cutter bar Fig 4 ltem A Clean the groove in the cutter bar Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336
17. directives and norms for the following product d clare la conformit suivante selon la directive CE et les normes concernant l article dichiara la seguente conformita secondo la direttiva UE e le norme per l articolo verklaart de volgende overeenstemming conform EU richtliin en normen voor het product declara la siguiente conformidad a tenor de la directiva y normas de la UE para el articulo declara a seguinte conformidade de acordo com a directiva CE e normas para o artigo attesterer f lgende overensstemmelse i medf r af EU direktiv samt standarder for artikel f rklarar f ljande verensst mmelse enl EU direktiv och standarder f r artikeln ep vakuuttaa ett tuote t ytt EU direktiivin ja standardien vaatimukset t endab toote vastavust EL direktiivile ja standarditele vyd v n sleduj c prohl en o shod podle sm rnice EU a norem pro v robek potrjuje slede o skladnost s smernico EU in standardi za izdelek amp vyd va nasleduj ce prehl senie o zhode pod a smernice EU a noriem pre v robok a cikkekhez az EU ir nyvonal s Norm k szerint a k vetkez konformit st jelenti ki deklaruje zgodno wymienionego poni ej artyku u z nast puj cymi normami na podstawie dyrektywy WE AeKNapupa CbOTBETHOTO C bOTBeETCTBNE CHACHO lnpekTtuBa Ha EC n Hopmn 3a apTuHyn paskaidro du atbilst bu ES direkt vai un standartiem apib dina j atitikim EU reikala
18. ds the right hand on the rear handle and the left hand on the front handle when the engine is running Use a firm grip with thumbs and fingers encircling the chain saw handles A firm grip will help you reduce kickback and maintain control of the saw Don t let go 3 Make sure that the area in which you are cutting is free from obstructions Do not let the nose of the guide bar contact a log branch or any other obstruction which could be hit while you are operating the saw 4 Cutat high engine speeds Do not overreach or cut above shoulder height 6 Follow manufacturer s sharpening and maintenance instructions for the saw chain 7 Only use replacement bars and chains specified by the manufacturer or the equivalent Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 Safety features Fig 3 2 LOW KICKBACK SAW CHAIN helps significantly reduce kickback or the intensity of kickback due to specially designed depth gauges and guard links 5 CHAIN BRAKE LEVER HAND GUARD protects the operator s left hand in the event it slips off the front handle while saw is running 5 CHAIN BRAKE is a safety feature designed to reduce the possibility of injury due to kickback by stopping a moving saw chain in milliseconds It is activated by the CHAIN BRAKE lever 10 STOP SWITCH immediately stops the engine when tripped Stop switch must be pushed to O
19. during any cutting operation Taking the time to make needed adjustments to the saw chain will result in improved cutting performance and prolonged chain life Warning Always wear heavy duty gloves when handling saw chain or making saw chain adjustments 1 Before adjusting the chain tension screw you must slacken the 2x retaining nuts Otherwise this will damage the tension screw 2 Hold nose of guide bar up and turn adjustment screw D CLOCKWISE to increase chain tension Turning screw COUNTERCLOCKWISE will decrease amount of tension on chain Ensure the chain fits snugly all the way around the guide bar Fig 10 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support wwweinhell uk co uk Model Number 5336 3 After making adjustment and while still holding nose of bar in the uppermost position tighten the bar retaining nuts securely Chain has proper tension when it has a snug fit all around and can be pulled around by gloved hand Note If chain is difficult to rotate on guide bar or if it binds too much tension has been applied This requires minor adjustment as follows 4 Loosen the bar retaining nut so they are finger tight Decrease tension by turning the bar adjustment screw COUNTERCLOCKWISE slowly Move chain back and forth on bar Continue to adjust until chain rotates freely but fits snugly Increase tension by turning bar adjustment screw CLOCKWISE 5 When saw chain has proper tension
20. ears after date of purchase we will remedy the problem as fast as possible once it has been brought to our attention In the unlikely event of such an occurrence or if you require any information about the product please contact us via our helpline support services details of which are to be found both in this manual and on the product itself Please fill in and return the Warranty Card to the address provided We hope you will enjoy using your purchase for many years to come Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support wwweinhell uk co uk Model Number 5336 General Information amp Safety Instructions 2 When using the equipment a few safety orecautions must be observed to avoid injuries and damage 1 Read the operating instructions carefully and comply with them at all times It is important to consult these instructions in order to acquaint yourself with the unit its proper use and the important safety regulations 2 Keep this manual in a safe place so that the information is available at all times 3 If you give the equipment to any other person make sure that you pass on these operating instructions as well We can accept no liability for damage or accidents which arise due to non compliance with these instructions General safety regulations Explanation of the symbols and warning signs on the machine 1 Read the user manual before using the machine 2
21. er of log to avoid splintering Second cut from above overbuck to meet first cut and avoid pinching Fig 26 3 Log supported on both ends First overbuck 1 3 diameter of log to avoid splintering Second underbuck to meet first cut and avoid pinching Fig 27 Note The best way to hold a log while bucking is to use a sawhorse When this is not possible the log should be raised and supported by the limb stumps or by using supporting logs Be sure the log being cut is securely supported Bucking using a sawhorse Fig 28 For personal safety and ease of cutting the correct position for vertical bucking is essential Fig 28 1 Hold the saw firmly with both hands and keep the saw to the right of your body while cutting 2 Keep the left arm as straight as possible 3 Keep weight on both feet Caution When working with the saw always make sure that the saw chain and chain bar are sufficiently lubricated Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support wwweinhell uk co uk Model Number 5336 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 Maintenance Warning All maintenance work on the chainsaw apart from the work described in this manual may only be carried out by authorised after sales service personnel Chain brake operational test Test the chain brake periodically to ensure proper function
22. fter sales service outlet A setting screw for adjusting the chain lubrication Fig 37 Item A is located on the underside of the chain saw Turning the screw counter clockwise increases the chain lubrication turning it clockwise decreases the chain lubrication To check the chain lubrication hold the chain saw with the chain over a piece of paper and run it at full soeed for a few seconds You will be able to judge the set amount of oil from the paper Chain maintenance Chain sharpening Chain sharpening requires special tools to ensure that cutters are sharpened at the correct angle and depth For the inexperienced chain saw user we recommend that the saw chain be professionally sharpened by the nearest professional Service Centre If you feel comfortable sharpening your own saw chain special tools are available from the professional Service Centre Service Centre If you feel comfortable sharpening your own saw chain special tools are available from the professional Service Centre Chain sharpening Fig 38 Sharpen the chain using protective gloves and a round file of 03 16 4 8mm Always sharpen the cutters only with outward strokes Fig 38 observing the values given in Fig 39 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 is Ser Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support wwweinhell u
23. gine and let it run until the unit stops to remove fuel from carburettor Allow the engine to cool approx 5 minutes 4 Remove the spark plug Pour 1 teaspoon of clean 2 cycle oil into the combustion chamber Pull starter rope slowly several times to coat internal components Replace spark plug Fig 41 Note Store the unit in a dry place and away from possible sources of ignition such as a furnace gas hot water heater gas dryer etc Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support wwweinhell uk co uk Model Number 5336 Putting the saw back into operation 1 Remove spark plug 2 Pull starter rope briskly to clear excess oil from combustion chamber 3 Clean the spark plug and check that the electrode gap approx 0 6mm is correct 4 Prepare unit for operation Fill fuel tank with proper fuel oil mixture See Fuel and Lubrication Section Waste disposal The equipment and its accessories are made of various types of material such as metal and plastic Defective components must be disposed of as special waste Ask your dealer or your local council Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support wwweinhell uk co uk Model Number 5336 ISC GmbH Eschenstra e 6 D 94405 Landau Isar Konformit tserkl rung erkl rt folgende Konformit t gem EU Richtlinie und Normen f r Artikel explains the following conformity according to EU
24. he upper notch cut C on the side of the tree facing the felling direction E Be sure you don t make the lower cut too deep into the trunk The notch C should be deep enough to create a hinge F of sufficient width and strength The notch should be wide enough to direct the fall of the tree for as long as possible Warning Never walk in front of a tree that has been notched Make the felling cut D from the other side of the tree and 1 5 2 0 inches 3 5 cm above the edge of the notch C Never saw completely through the trunk Always leave a hinge The hinge guides the tree If the trunk is completely cut through control over the felling direction is lost Insert a wedge or felling lever in the cut well before the tree becomes unstable and starts to move This will prevent the guidebar from binding in the felling cut if you have misjudged the falling direction Make sure no bystanders have entered the range of the falling tree before you push it over Warning Before making the final cut always recheck the area for bystanders animals or obstacles Felling cut 1 Use wooden or plastic wedges A to prevent binding the bar or chain B in the cut Wedges also control felling Fig 22 2 When diameter of wood being cut is greater than the bar length make 2 cuts as shown Fig 23 Warning As the felling cut gets close to the hinge the tree should begin to fall When tree begins to fall remove saw from cut stop engine
25. iSC GmbH Customer Service 49 0 180 5120509 1actimin Eschenstra e 6 49 0 180 5835830 14ctimin 94405 Landau an der Isar info isc gmbh info www isc gmbh info Artikel Nr Petrol Chain Saw Ident Nr 01018 Komponenten Ersatzteile Position Artikel Nr Beschreibung Position Artikel Nr Beschreibung 6 450139001006 SPARK PLUG LDL7T 55 450139001055 Carburetor 10 450139001010 MUFFLER 61 450139001061 FILTER AIR 15 450139001015 RING PISTON 78 450139001078 SPIKE 16 450139001016 PISTON 87 450139001087 OIL PUMP 17 450139001017 RING SNAP D11 93 450139001093 PAD RIGHT 18 450139001018 PIN PISTON D11x34 D11x34 97 450139001097 KNOB AIR FILTER f r Luftfilter 24 450139001024 ELECTRONIC IGNITION 98 450139001098 RUBBER WASHER 27 450139001027 OIL CAP 99 450139001099 COVER AIR FILTER f r Luftfilter Komponenten Ersatzteile Position Artikel Nr Beschreibung 114 450139001114 OIL FILTER 127 450139001127 COVER REAR HANDLE f r Handgriff 133 450139001133 GASOLINE CAP 166 450139001166 18 GUIDE BAR COVER der Leitschiene 902 450139001902 starter cable cpl 904 450139001904 oil filter cpl 0 450139001186 rubber valve GLPC4645 GARDENLINE PETROL CHAINSAW GARDENLINE Now you have purchased a Gardenline product you can rest assured in the knowledge that as well as your 3 year parts and labour warranty you have the added peace of mind of dedicated helplines and web support AFTE
26. ies when an on site service is used Of course we are also happy offer a chargeable repair service for any defects which are not covered by the scope of this guarantee or for units which are no longer covered To take advantage of this service please send the device to our service address Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support wwweinhell uk co uk Model Number 5336 The reprinting or reproduction by any other means in whole or in part of documentation and papers accompanying products is permitted only with the express consent of ISC GmbH Technical changes subject to change Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support wwweinhell uk co uk Model Number 5336 GLPC4645 09 2009 es le
27. ing blended with oxygenates such as alcohol or an ether compound to meet clean air standards Your engine is designed to operate satisfactorily on any fuel intended for automotive use including oxygenated fuel It is recommended to use unleaded petrol as fuel Lubrication of chain and chain bar Whenever you refill the fuel tank with petrol you must also top up the level of chain oil in the chain oil tank It is recommended to use standard chain oil Engine pre start checks Warning Never start or operate the saw unless the bar and chain are properly installed 1 Fillthe fuel tank A with correct fuel mixture Fig 15 2 Fill the oil tank B with chain oil Fig 15 3 Be certain the chain brake is disengaged C before starting unit CFig 15 Once you have filled the chain and oil tank tighten the tank cover securely by hand Do not use any tools to do so Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support wwweinhell uk co uk Model Number 5336 Features 5 e 45cm cutting length e Automatic choke amp primer assisting start up e 21m s chain speed e 550ml fuel tank capacity e Mixer bottle included e Soft carry bag included Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support wwweinhell uk co uk Model Number 5336 Instructions 6 Operation Starting the engine 1 Set the On Off switch A Fig 16 to Off O to stop the machine
28. install saw chain 1 Spread the chain out in a loop with the cutting edges A pointing CLOCKWISE around loop Fig 9 2 Slip the chain around the sprocket B behind the clutch C Make sure the links fit between the sprocket teeth Fig 10 3 Guide the drive links into the groove D and around the end of the bar Fig 10 Note The saw chain may droop slightly on the lower part of bar This is normal 4 Pull the chain bar forward until the chain is closely seated Make sure that all the drive links are in the groove of the bar 5 Using a screwdriver run the adjustment screw Fig 11A Item G and Fig 11B Item G COUNTERCLOCKWISE until the TANG Fig 6 ltem E projecting prong is to the end of its travel toward the circular brake band Fig 6 6 Et the Chain brake lever front handle guard by aligning the tang with the slot in the chain bar re adjust the tang position if it does not line up correctly Make sure that the pivot Fig 6 Iltem E fits into the chain bar Fig 8 ltem G Make sure that the rubber strip Fig 6 item H is flat and does not get caught on the engine wall during assembly The chain must not slip off the bar when you do this Fit the two nuts Fig 7 Item B and tighten them by hand and then follow the instructions for adjusting the tension in ADJUSTING THE CHAIN TENSION Saw chain tension adjustment Proper tension of the saw chain is extremely important and must be checked before starting as well as
29. k co uk Model Number 5336 After sharpening the cutting links must all have the same width and length Warning A sharp chain produces well defined chips When your chain starts to produce sawdust it is time to sharpen After the blades have been sharpened 3 4 times check the height of the depth limiter and if necessary lower it with a flat file and then round off the front corner Fig 40 Chain tension Check the chain tension frequently and adjust as often as necessary to keep the chain snug on the bar but loose enough to be pulled around by hand Breaking in a new saw chain A new chain and bar will need chain readjustment after as few as 5 cuts This is normal during the break in period and the interval between future adjustments will begin to lengthen quickly Warning Never have more than 3 links removed from a loop of chain This could cause damage to the sprocket If in doubt please call the customer helpline Chain lubrication Always make sure the automatic oiler system is working properly Keep the oil tank filled with chain bar and sprocket oil Adequate lubrication of the bar and chain during cutting operations is essential to minimize friction with the guide bar Never starve the bar and chain of lubricating oil Running the saw dry or with too little oil will decrease cutting efficiency shorten saw chain life cause rapid dulling of chain and lead to excessive wear of bar from overheating Too little oil
30. l uk co uk Model Number 5336 3 Clean air filter Wash filter in clean warm soapy water Rinse in clear cool water Air dry completely Note It is advisable to have a supply of spare filters A Insert the air filter Fit the cover for the engine air filter Make sure that the cover fits perfectly when you do so Tighten the fastening screw for the cover Fuel filter Warning Never use the saw without a fuel filter After 100 hours in operation the fuel filter should be cleaned or in case of damage replaced Be sure to empty the fuel tank before changing the filter 1 Remove the fuel tank cap 2 Benda piece of soft wire Reach into fuel tank opening and hook fuel line Carefully pull the fuel line toward the opening until you can reach it with your fingers Note Do not pull hose completely out of tank 4 Lift filter A out of tank Fig 33 5 Pull off the filter with a twist and clean it if the filter is damaged dispose of it 6 Insert a new filter Place one end of the filter into the tank opening Make sure that the filter is seated in the lower corner of the tank If necessary use a long screwdriver to move the filter to its correct position taking care not to damage in the process 7 Fill tank with fresh fuel oil mixture See Section Fuel and Lubrication Install fuel cap Spark plug Fig 32 Warning To ensure that the saw s engine retains its power the spark plug must be clean and have the co
31. n 1 position to start or restart engine 11 SAFETY TRIGGER prevents accidental acceleration of the engine Throttle trigger 19 cannot be squeezed unless the safety latch is depressed 20 CHAIN CATCHER reduces the danger of injury in the event saw chain breaks or derails during operation The chain catcher is designed to intercept a whipping chain Note Study your saw and be familiar with its parts Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IOC 946244 Web Support wwweinhell uk co uk Model Number 5336 Proper use The chain is designed exclusively for sawing wood You May only fell trees if you have received the appropriate training The manufacturer cannot be held liable for damage caused by improper or incorrect usage Please note that our equipment has not been designed for use in commercial trade or industrial applications Our warranty will be voided if the machine is used in commercial trade or industrial businesses or for equivalent purposes Environmental protection Dispose of soiled maintenance material and operating materials at the appropriate collection point Recycle packaging material metal and plastics Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support www einhell uk co uk Model Number 5336 Assembly amp Parts List 5 Layout Fig 3 1 Chain bar 11 Safety lock
32. pline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support wwweinhell uk co uk Model Number 5336 Turning the chain bar The bar should be reversed every 8 working hours to ensure uniform wear Keep the bar groove and lubrication hole clean using the bar groove cleaner supplied optional Fig 35 Check the bar rails frequently for wear and if necessary remove the burs and square up the rails using the flat file Fig 36 Warning Never fit anew chain to a worn chain bar Oil passages Oil passages on the bar should be cleaned to ensure proper lubrication of the bar and chain during operation Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IS9O 946244 Web Support wwweinhell uk co uk Model Number 5336 Note The condition of the oil passages can be easily checked If the passages are clear the chain will automatically give off a spray of oil within seconds of starting the saw Your saw is equipped with an automatic oiler system Automatic chain lubrication The chain saw is equipped with an automatic oil lubrication system with a toothed wheel drive It automatically supplies the bar and the chain with the right quantity of oil The moment the engine is accelerated the oil also starts to flow through the bar plate more quickly as well The chain lubrication system has been set to its perfect adjustment at the factory If it requires adjusting take the saw to your nearest authorized a
33. rrect electrode gap 0 6 mm The spark plug must be cleaned or replaced after every 20 hours of service 1 Set the On Off switch to Stop O 2 Remove the top cover A by undoing the cover fastening screw B on the cover You can then remove the filter C Fig 31 Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 3 Disconnect the ignition cable D from the spark plug by pulling and twisting it simultaneously Fig 32 4 Remove the spark plug using a spark plug wrench DO NOT USE ANY OTHER TOOLS 5 Clean the spark plug with a copper wire brush or fit a new one Carburettor setting The carburettor has been set to its perfect adjustment at the factory If it requires adjusting take the saw to your nearest authorised after sales service outlet Chain bar maintenance Regular lubrication of the chain bar guide rail for the chain and teeth is essential The chain bar needs the maintenance described in the following section in order for the saw to work at an optimum level of performance Caution The sprocket tip on your new saw has been pre lubricated at the factory Failure to lubricate the guide bar sprocket tip as explained below will result in poor performance and seizure voiding the manufacturer s warranty Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I890 946244 Web Support www einhell uk co uk Model Number 5
34. strial applications or for other equivalent activities The following are also excluded from our guarantee compensation for transport damage damage caused by failure to comply with the installation assembly instructions or damage caused by unprofessional installation failure to comply with the operating instructions e g connection to the wrong mains voltage or current type misuse or inappropriate use such as overloading of the device or use of non approved tools or accessories failure to comply with the maintenance and safety regulations ingress of foreign bodies into the device e g sand stones or dust effects of force or external influences e g damage caused by the device being dropped and normal wear resulting from proper operation of the device The guarantee is rendered null and void if any attempt is made to tamper with the device The guarantee is valid for a period of 3 years starting from the purchase date of the device Guarantee claims should be submitted before the end of the guarantee period within two weeks of the defect being noticed No guarantee claims will be accepted after the end of the guarantee period The original guarantee period remains applicable to the device even if repairs are carried out or parts are replaced In such cases the work performed or parts fitted will not result in an extension of the guarantee period and no new guarantee will become active for the work performed or parts fitted This also appl
35. tions Important Felling trees is prohibited without the necessary training Felling Felling is the term for cutting down a tree Small trees up to 6 7 inches 15 18cm in diameter are usually cut in a single cut Larger trees require notch cuts Notch cuts determine the direction the tree will fall Warning A retreat path A should be planned and cleared as necessary before cuts are started The retreat path should extend back and diagonally to the rear of the expected line of fall as illustrated in Fig 20 Warning If felling a tree on sloping ground the chain saw operator should keep on the uphill side of the terrain as the tree is likely to roll or slide downhill after it is felled Note Direction of fall B is controlled by the notching cut Before any cuts are made consider the location of larger branches and natural lean of the tree to determine the way the tree will fall Fig 20 Warning Do not cut down a tree during high or changing winds or if there is a danger to property Consult a tree professional Do not cut down a tree if there is a danger of striking utility wires notify the utility company before making any cuts Helpline No UK Northern Ireland OISI 6491500 Rep Ireland I8S90 946244 Web Support wwweinhell uk co uk Model Number 5336 General guidelines for felling trees Fig 21 Normally felling consists of 2 main cutting operations notching C and making the felling cut D Start making t
36. vimams ir prek s normoms declar urm toarea conformitate conform directivei UE i normelor pentru articolul SNAWVEL THV AK AOUON ouvup ppwon o upwva HE TNV Odnyia EK kal ta TIPOTUTIA yia TO TIPOIOV potvr uje sljede u uskla enost prema smjernicama EU i normama za artikl potvr uje sljede u uskla enost prema smjernicama EU i normama za artikl potvr uje slede u uskla enost prema smernicama EZ i normama za artikal CJIEAYIOLLIUM YAOCTOBEPAETCA YTO cnegyione NPOAYHTbI COOTBETCTBYWT ANPEKTNBAaM N HODMaM EC nporonowye npo 3a3HayeHy HMHWYe BIANOBIAHICTb BNPO6y AMNpeHTHBaM Ta CTaHAaptam EC Ha Bupi6 ja n3jaByBa CneaHaTa C0o0O6P3HOCT comacHo EY anpekTuBaTa uU HOPMMTe 3a apTuKs n r n ile ilgili AB direktifleri ve normlar gere ince asagida aciklanan uygunlugu belirtir erkl rer folgende samsvar i henhold til EU direktivet og standarder for artikkel L sir uppfyllingu EU regIna og annarra sta la v ru Petrol Chainsaw GLPC 4645 _ 2006 95 EC _ 2005 32 EC x 2004 108 EC _ 2004 22 EC C 1999 5 EC C 97 23 EC C 95 54 EC C 90 396 EC _ 89 686 EC_96 58 EC 2006 42 EC x 98 37 EC x Annex IV x Annex V _ Annex VI P 2 KW x 97 68 EC Notified Body Intertek Notified Body No 0905 Reg No O9SHW1193 01 x 2000 1 4 EC_2005 88 EC Noise measured Lwa 110 dB A guaranteed Lwa 116 dB A Emission No e11 97 68SA 2004 26 0825 00 _ 87 404 EC St
37. when the chain brake is applied 11 Shut off the engine before setting the chain saw down Helpline No UK Northern Ireland OISI 6491500 Rep Ireland IB90 946244 Web Support wwweinhell uk co uk Model Number 5336 12 Use extreme caution when cutting small size brush and saplings because slender material may catch the saw chain and be whipped toward you or pull you off balance 13 When cutting a limb that is under tension be alert for springback so that you will not be struck when the tension in the wood fibers is released 14 Keep the handles dry clean and free of oil or fuel mixture 15 Operate the chain saw only in well ventilated areas 16 DO NOT operate a chain saw in a tree unless you have been specifically trained to do so 17 All chain saw service other than the items listed in the user manual safety and maintenance instructions should be performed by competent chain saw service personnel 18 When transporting your chain saw use the appropriate guide bar scabbard 19 DO NOT operate your chain saw near or around flammable liquids or gases whether in or out of doors An explosion and or fire may result 20 Do not fill fuel tank oil or lubricate when the engine of chain saw is running 21 USE THE RIGHT TOOL Cut wood only Do not use the chain saw for purposes for which it was not intended For example do not use the chain saw for cutting plastic masonry or non building materials 22 The engine will cre
Download Pdf Manuals
Related Search