S70 Series - Datalogic
Contents
1. 2 seconds after adjustment the GREEN display will flash 3 times to confirm e Slide Mode switch to RUN to complete operation Remember Manual adjustments are disabled when Auto Thresholds are ON Follow these steps to perform a Two Point TEACH NOTE TEACH Selection must be programmed to 2Pt tcH see Program Mode 1 Enter Adjust mode Method Action Result 2 Set the Mode switch to ADJ RUN PRG ADJ Display Red Signal Level SET Button Green Threshold Remote Input 3 No action is required sensor is ready for HEE EEEH the Two Point TEACH method 2 SET Button 0 04 seconds lt Click lt 0 8 seconds 3 Remote Input 0 04 seconds lt T lt 0 8 seconds DATALOGIC 2 Teach the first condition Method SET Button Remote Input Action a Present the first condition b Click the SET Navigation key a Present the first condition b Single pulse the remote input 3 Teach the second condition Method SET Button Remote Input 4 Return to Run mode Method SET Button Remote Input Dynamic TEACH e Teaches on the fly Action a Present the second condition b Click the SET Navigation key a Present the second condition b Single pulse the remote input Action Move the Mode switch to RUN No action is required sensor returns to RUN mode automatically e Establishes a single switching threshold e Threshold can be adjusted using and Navigation key Manual Adjust Dy2. lt sDATALOGIC S70 Series Advanced sensor with dual digital displays for use with plastic and glass fiber optic assemblies For complete technical information about this product including dimensions accessories and specifications see www datalogic com Output LED LO DO Switch RUN PRG ADJ Mode Switch Lever Action Fiber Clamp Red Signal Level Green Threshold SET Navigation key Figure 1 Never use this device as a sensing device for personnel protection Doing so could lead to serious injury or death This device does not include the self checking redundant circuitry necessary to allow its use in personnel safety applications A sensor failure or malfunction can cause either an energized or de energized sensor output condition WARNING Not to be used for personnel protection Model Outputs Connector 2 E1 ingle NPN se Aad i Single 2 m cable 4 wire 70 2 E1 P Single PNP S70 5 E1 N Single NPN 70 5 E1 P Single PNP Integral M8 Pico QD connector 4 pin _F_E4 Dual outputs 1 push pull IO Link and 1 PNP 70 5 E1 P2 complementary outputs 5 E2 Single NPN PEEN 2 Integral M8 Pico QD connector 4 pin S70 5 E2 P Single PNP CONNECTIONS NPN Version PNP Version io Key 10 30 VDC 3 10 30 VDC 1 Brown 2 White om a r 2 L Remote l Ba Programming N O Programming N O IO Link Version Pico 4 2 3 Cy 1 18 30 VDC NOTE Open lead wires must be connected to a terminal block 1 A model with
3. Threshold Response Speed Offset Percent Auto Thresholds OFF Delay OFF One Shot ON One Shot Gain Selection Threshold OFF Delay Program Mode DATALOGIC ADJUST MODE Sliding the RUN PRG ADJ mode switch to the ADJ position allows the user to perform Expert TEACH SET methods and Manual Adjustment of the threshold s Two Point TEACH e Establishes a single switching threshold e Threshold can be adjusted using and Navigation key Manual Adjust Two Point TEACH is used when two conditions can be presented statically to the sensor The sensor locates a single sensing threshold the switch point midway between the two taught conditions with the Output ON condition on one side and the Output OFF condition on the other see Fig 2 Darkest Taught Lightest Taught Condition Condition Sensor positions threshold midway between taught conditions I i 1 Output OFF Output ON lt gt Darkest Position Most Light no signal adjusted by saturated Manual Adjust signal Figure 2 Two Point TEACH Light Operate shown The Output ON and OFF conditions can be reversed by using the LO DO Light Operate Dark Operate switch see LO DO Switch in Top Panel Interface Two Point TEACH and Manual Adjust Moves switching threshold value up or down to make adjustments e Slide Mode switch to ADJ to enter Adjust mode e Press to increase press to decrease GREEN display shows the switching threshold value
4. FAIL without Offset Presented condition cannot be used for the SET method Threshold Alert or Threshold Error Severe contamination changes in the taught condition can prevent the Auto Thresholds algorithm from optimizing the threshold s Display Description Corrective Action Threshold Alert Alternates The threshold s cannot be Cleaning correcting the sensing optimized but the sensor s output environment and or a re teach of the will still continue to function sensor is highly recommended Threshold Error The threshold s cannot be Cleaning correcting the sensing optimized and the sensor s output environment and or a re teach of the will stop functioning sensor is required 16 Mh az TECHNICAL DATA Sensing Beam Supply Voltage Power and Current Consumption exclusive of load Supply Protection Circuitry Delay at Power Up Output Configuration Output Rating Output Protection Output Response Time Repeatability Environmental Rating Operating Temperature Storage Temperature Humidity 10 Link Interface Certifications DATALOGIC S70 x E1 S70 x E2 660 nm visible red 635 nm visible red NPN PNP models 10 30 VDC Class 2 10 max ripple IO Link models 18 30 V dc 10 max ripple Standard display mode 960 mW Current consumption lt 40 mA at 24 VDC ECO display mode 720 mW Current consumption lt 30 mA at 24 VDC Protected against reverse polarity overvoltag
5. AUTOMATION srl Via Lavino 265 40050 Monte S Pietro Bologna Italy Tel 39 051 6765611 Fax 39 051 6759324 www datalogic com DATALOGIC AUTOMATION reserves the right to make modifications and improvements without prior notification 821002591 Rev A 161275C 177900B
6. SET Click SET Click SET Click SET to enter choice list to enter choice list to enter choice list to enter choice list to enter choice to enter choice list to enter choice list to enter choice list to enter choice list to enter choice list to enter choice list vy vy y y y y y y Ce o E He Bee Beceem LJ o or or or or ixed Gal ERETT 5020 Pega eega begt pesansa ES TE BE IKAT T 9999 ms 9999 ms 9999 ms 9999 ms 23 E 3 999 Pet display flips 180 s Sg Ltset PEZI ASIP 8 2 for th l or the value see a amp Technical Data dect dSIP pag 17 EZL 094 CALSEt lt 1 d L 094 CS CS he x on display represents a w in on display represents a m gt a lt x ie a a ow Factory Default Two Point TEACH Standard 500 us 0 Disabled 0 Disabled 0 Disabled 0 Disabled Numeric ECO disabled Normal Orientation Factory Default Two Point TEACH Standard 250 us 0 Disabled O Disabled O Disabled 0 Disabled Numeric ECO disabled Normal Orientation 70 E1 Factory Default Settings OFF Auto Gain 70 E2 Factory Default Settings OFF Auto Gain Program PRG mode allows the following settings to be programmed c o 2 N pa Display Readout Response Speed Offset Percent Auto Thresholds OFF One Shot ON One Shot Display Readout Gain Selection c 2 E w N le z H in the S70
7. a OD connector requires a mating cordset wDATALOGIC MOUNTING INSTRUCTIONS Mount on a DIN Rail 1 Hook the DIN rail clip on the bottom of the S70 over the edge of the DIN rail 1 2 Push the S70 up on the DIN rail 1 3 Pivot the S70 onto the DIN rail pressing until it snaps into place 2 Remove from a DIN rail 1 Push the S70 up on the DIN rail 1 2 Pivot the S70 away from the DIN rail and remove it 2 INSTALLING THE FIBERS Follow these steps to install glass or plastic fibers Move forward to release the fibers 1 Open the dust cover Fiber Clamp 2 Move the fiber clamp forward to unlock it cen Recker Park 3 Insert the fiber s into the fiber port s until they stop 4 Move the fiber clamp backward to lock the fiber s pete neh ot 5 Close the dust cover Fiber Adapters NOTE If a thin fiber with less than 2 2 mm outer diameter is used install the fiber adapter provided with the fiber assembly to ensure a reliable fit in the fiber holder Datalogic includes the adapters with all fiber assemblies TO Ne Fiber Outer Diameter mm Adapter Color aa Black Red No adapter needed 3 TO SENSOR When connecting coaxial type fiber assemblies to the amplifier install the solid core fiber to the LED emitting port and the multi core fiber to the PD receiving port for most reliable detection RECEIVER Multi core fiber EMITTER Single core fiber a w DATALOG
8. display will flash 3 times to confirm e Slide Mode switch to RUN to complete operation Remember Manual adjustments are disabled when Auto Thresholds are ON Follow these steps to perform a Dynamic TEACH NOTE TEACH Selection must be programmed to dYn tcH see Program Mode 1 Enter Adjust Mode Method Action Result SET Button gt Set Mode switch to ADJ RUN PRG ADJ Display Red Signal Level Green Threshold Remote Input 6 No action required sensor is ready for EEL EPR Dynamic TEACH method 2 Enter Dynamic TEACH Method Action SET Button Click the SET Navigation key C pig Remote Input Single pulse remote input Result Display Flashes dYn tch then holds on 1234 dYn 3 Present ON and OFF Conditions Method Action Result Display Red Signal Level SET Button Present ON and OFF conditions Green Threshold Remote Input Present ON and OFF conditions EEG HH 5 SET Button 0 04 seconds lt Click lt 0 8 seconds 6 Remote Input 0 04 seconds lt T lt 0 8 seconds 4 Exit Dynamic TEACH Method SET Button Remote Input 5 Return to RUN Mode Method Action SET Button Remote Input Click the SET Navigation key Single pulse remote input Move Mode switch to RUN DATALOGIC Action RUN PRG ADJ No action required sensor returns to RUN mode automatically Window SET Result TEACH Accepted Displays alternate PASS with Minimum Difference Sensor return
9. flash 3 times to confirm e Slide Mode switch to RUN to complete operation Remember Auto Thresholding is automatically disabled in Calibration SET Follow these steps to perform a Calibration SET Note TEACH Selection must be programmed to CAL SEt see Program Mode 1 Enter Adjust Mode Method Action Result SET Button 7 i RUN PRG ADJ Ser E E Oar Display Red Signal Level Green Threshold Remote Input 18 No action required sensor is ready for EEE EH Calibration SET method 17 SET Button 0 04 seconds lt Click lt 0 8 seconds 18 Remote Input 0 04 seconds lt T lt 0 8 seconds 14 wDATALOGIC 2 SET Sensing Condition Method Action Result Present sensing condition RUN PRG ADJ Threshold Condition Accepted er RUG Click the SET Navigation key p T P Displays read CAL SEt then flashes PASS Sensor returns to Adjust mode Present sensing condition T Remote Input Single pulse the remote input Threshold Condition Unacceptable Displays read CAL SEt then flashes FAIL Sensor returns to Adjust mode 1 Return to RUN Mode Method Action Result SET Button Move Mode switch to RUN RUN PRG ADJ Display Red Signal Level Green Threshold Remote Input No action required sensor returns to RUN HH A mode automatically 15 DATALOGIC IO Link Interface IO Link is a point to point communication link between a master device and sensor It can be used to automatically pa
10. IC TOP PANEL INTERFACE Opening the dust cover provides access to the top panel interface The top panel interface consists of the RUN PRG ADJ mode switch LO DO switch SET Navigation key dual red green digital displays and output LED RUN PRG ADJ Mode Switch RUN PRG ADJ 3 The RUN PRG ADJ mode switch puts the sensor in RUN PRG Program or ADJ Adjust mode RUN mode allows the sensor to operate normally and prevents unintentional programming changes via the SET button PRG mode allows the sensor to be programmed through the display driven programming menu see Program Mode below ADJ mode allows the user to perform Expert TEACH SET methods and Manual Adjust see Adjust Mode below LO DO Switch LO DO ae The LO DO switch is used to select Light Operate or Dark Operate mode In Light Operate mode the output sensing condition is inside the window In Dark Operate mode the output is ON when the sensing condition is ON when the sensing condition is above the threshold for Window SET the output is ON when the is below the threshold for Window SET the output is ON when the sensing condition is outside the window SET Navigation key The SET Navigation key is a 3 way button The positions are engaged by rocking the button left right The SET position is engaged by clicking down the button while the rocker is in the middle position All three button positions are used during PRG mode to navigate the di
11. dition Most Light no signal Presented saturated signal Figure 7 Dark SET Light Operate shown 13See Troubleshooting for more explanation of the Offset displayed after the Light SET method 12 DATALOGIC Moves switching threshold value up or down to make adjustments e Slide Mode switch to ADJ to enter Adjust mode e Press to increase press to decrease oGREEN display shows the switching threshold value 2 seconds after adjustment the GREEN display will flash 3 times to confirm e Slide Mode switch to RUN to complete operation Remember Manual adjustments are disabled when Auto Thresholds are ON Follow these steps to perform a Dark SET Note TEACH Selection must be programmed to dr SEt see Program Mode 1 Enter Adjust Mode Method Action Result SET Button 24 Set Mode switch to ADJ RUN PRG ADJ Display Red Signal Level Green Threshold Remote Input 15 No action required sensor is ready for Dark SET method 2 SET Sensing Condition Method Action Result SET Button a e A i Threshold Condition Accepted A p e Click the SET Navigation key Displays read dr SEt then alternate PASS with Offset 6 Sensor returns to Adjust mode Present sensing condition a ES Remote Input Single pulse the remote input Threshold Condition Not Accepted Displays read dr SEt then alternate FAIL with minimum Offset for sensing condition Sensor returns to Adjust mode 3 Return to RUN Mod
12. e Method Action Result SET Button Move Mode switch to RUN RUN PRG ADJ Display Red Signal Level Green Threshold Remote Input No action required sensor returns to RUN Ba Be mode automatically 14 SET Button 0 04 seconds lt Click lt 0 8 seconds 15 Remote Input 0 04 seconds lt T lt 0 8 seconds 16See Troubleshooting on page 16 for more explanation of the Offset displayed after the Dark SET method 13 DATALOGIC Calibration SET e Sets a threshold exactly at the presented condition e Threshold can be adjusted using and Navigation key Manual Adjust A single sensing condition is presented and the sensor positions a threshold exactly at the presented condition When a condition lighter than the threshold is sensed the output either turns ON or OFF depending on the LO DO switch setting see LO DO Switch in Top Panel Interface Threshold position adjusted by Manual Adjust C S E a Sensor positions threshold exactly at the presented condition Output OFF Output ON Darkest Condition Most Light no signal Presented saturated signal Figure 8 Calibration SET Light Operate shown Calibration SET and Manual Adjust Moves switching threshold value up or down to make adjustments e Slide Mode switch to ADJ to enter Adjust mode e Press to increase press to decrease GREEN display shows the switching threshold value 2 seconds after adjustment the GREEN display will
13. e and transient voltages NPN PNP models 1 current sinking NPN or 1 current sourcing PNP output depending on model complement oututsy complementary outputs 100 mA max load derate 1 mA per C above 30 C OFF state leakage current NPN PNP models lt 5 pA at 30 VDC ON state saturation voltage NPN lt 1 5 V PNP IO Link lt 2 V po lOlink lt 50pAat30VDC S a Protected against output short circuit continuous overload transient over voltages and false pulse on power up Super High Speed 10 us High Speed 15 us Fast 50 us Standard 250 us Medium Range 500 us Long Range 1000 us Super High Speed 5 us High Speed 5 us Fast 12 us Standard 50 us Medium Range 80 us Long Range 165 us Black ABS Polycarbonate alloy UL94 V 0 rated housing clear polycarbonate cover O C ac FOO C gt 20 C 85 C 90 at 60 C maximum relative humidity non condensing Supports Smart Sensor Profile Yes Baud Rate 38 400 bps COM2 Process Data Width 16 bits IODD files Provide all programming options of top panel interface plus additional functionality 10 Link a E High Speed 200 us Standard 500 us Long Range 2 ms Extra Long Range 5 ms High Speed 66 us Standard Long Range 100 us Extra Long Range 100 us 17 DATALOGIC OVERALL DIMENSIONS CABLE VERSION i n l i 1 l CONNECTOR VERSION EE i i l T l l T Dimensions in mm DATALOGIC
14. for more explanation of the Offset displayed after the Window SET method 9 DATALOGIC Method Action SET Button Move Mode switch to Run RUN PRG ADJ Display Red Signal Level Green Window Center see Figure 5 for instructions on how to display upper and lower thresholds 3 Return to RUN Mode Result Remote Input No action required sensor returns to Run mode automatically eea ano Window SET during RUN mode Upon sensor power up Window Center is displayed ka 1234 2200 1234 2000 1234 1800 amp Upper Window Lower Threshold Center Threshold Displayed Displayed Displayed Figure 5 Upper and Lower Thresholds 10 DATALOGIC e Sets a threshold a programmable offset below the presented condition e Changes output state on any condition darker than the threshold condition e Threshold can be adjusted using and Navigation key Manual Adjust e Recommended for applications where only one condition is known for example a stable light background with varying darker targets e See Program Mode for programming the Offset Percent setting A single sensing condition is presented and the sensor positions a threshold a programmable offset below the presented condition When a condition darker than the threshold is sensed the output either turns ON or OFF depending on the LO DO switch setting see LO DO Switch in Top Panel Interface Threshold position adjusted by Manual Adj
15. he Minimum difference displayed after the Dynamic TEACH method w DATALOGIC Moves sensing window center value up or down to make adjustments e Slide Mode switch to ADJ to enter Adjust mode e Press to increase press to decrease GREEN display shows the sensing window center value 2 seconds after adjustment the GREEN display will flash 3 times to confirm e Slide Mode switch to RUN to complete operation Remember Manual adjustments are disabled when Auto Thresholds are ON Follow these steps to perform a Window SET Note TEACH Selection must be programmed to wind SEt see Program Mode 1 Enter Adjust Mode Method Action Result SET Button Set Mode switch to ADJ RUN PRG ADJ Display Red Signal Level Green Threshold Remote Input 9 No action required sensor is ready for EEE HHH Window SET method 2 SET Sensing Condition Method Action Result Present sensing condition SET Button Click the SET Navigation key Threshold Condition Accepted Displays read wind SEt then alternate PASS with Offset Sensor returns to Adjust mode Present sensing condition Remote Input Single pulse the remote input Threshold Condition Not Accepted Displays read wind SEt then alternate FAIL with minimum Offset for sensing condition Sensor returns to Adjust mode 8 SET Button 0 04 seconds lt Click lt 0 8 seconds 9 Remote Input 0 04 seconds lt T lt 0 8 seconds 1 see Troubleshooting on page 16
16. namic TEACH is best used when a machine or process may not be stopped for teaching The sensor learns during actual sensing RUN PRG ADJ Result Display Flashes 2Pt tch then holds on 1234 2nd Result TEACH Accepted Displays alternate PASS and Minimum Difference Sensor returns to Adjust mode TEACH Not Accepted Displays alternate FAIL and Minimum Difference Sensor returns to Adjust mode Result Display Red Signal Level Green Threshold conditions taking multiple samples of the light and dark conditions and automatically setting the threshold at the optimum level see Fig 3 Darkest Taught Condition Lightest Taught Condition Sensor positions threshold midway between taught conditions Output OFF Output ON Darkest Aca Most Light no signal adjust d by saturated Manual Adjust f signal Figure 3 Dynamic TEACH Light Operate shown The output ON and OFF conditions can be reversed using the LO DO switch see LO DO Switch in Top Panel Interface 4 See Troubleshooting on page 16 for more explanation of the Minimum Difference displayed after the Two Point TEACH method DATALOGIC Dynamic TEACH and Manual Adjust Moves switching threshold value up or down to make adjustments e Slide Mode switch to ADJ to enter Adjust mode e Press to increase press to decrease GREEN display shows the switching threshold value 2 seconds after adjustment GREEN
17. ote Input e Single pulse the remote input U Threshold Condition Not Accepted Displays read Lt SEt then alternate FAIL with minimum Offset for sensing condition Sensor returns to Adjust mode 3 Return to RUN Mode Method Action Result SET Button Move Mode switch to RUN RUN PRG ADJ Display Red Signal Level Green Threshold Remote Input No action required sensor returns to RUN mode automatically Dark SET e Sets a threshold a programmable offset above the presented condition e Any condition lighter than the threshold condition causes the output to change state e Threshold can be adjusted using and Navigation key Manual Adjust e Recommended for applications where only one condition is known for example a stable dark background with varying lighter targets e See Program Mode for programming the Offset Percent setting NOTE Offset Percent MUST be programmed to Minimum Offset to accept conditions of no signal 0 counts A single sensing condition is presented and the sensor positions a threshold a programmable offset above the presented condition When a condition lighter than the threshold is sensed the output either turns ON or OFF depending on the LO DO switch setting see LO DO Switch in Top Panel Interface Threshold position adjusted by Manual Adjust Sensor positions threshold a programmable Offset above the presented condition Output OFF Output ON Darkest Con
18. rameterize sensors and transmit process data For the latest IO Link protocol and specifications please visit the web site at www io link com The IO Link IODD package is available on the Datalogic Website at www datalogic com Troubleshooting Manual Adjustments Disabled Manual adjustments are disabled when Auto Thresholds are ON If a manual adjustment is attempted while Auto Thresholds are ON the Green display will flash Autol Percent Minimum Difference after TEACH The Two Point and Dynamic TEACH methods will flash a minimum difference on the displays after a PASS or FAIL Value PASS FAIL Description 0 to 99 FAIL The difference of the taught conditions does not meet the required minimum 100 to 300 PASS The difference of the taught conditions just meets exceeds the required minimum minor sensing variables may affect sensing reliability 300 to 600 PASS The difference of the taught conditions sufficiently exceeds the required minimum minor sensing variables will not affect sensing reliability 600 PASS The difference of the taught conditions greatly exceeds the required minimum very stable operation Percent Offset after SET The Window Dark and Light SET methods will flash a offset on the displays after a PASS or FAIL SET Result Offset Meaning PASS with Offset Displays the offset used for the SET method FAIL with Offset Displays the minimum required offset necessary to PASS the SET method
19. s to Adjust mode TEACH Not Accepted Displays alternate FAIL with Minimum Difference Sensor returns to Adjust mode Result Display Red Signal Level Green Threshold e Sets window thresholds that extend a programmable offset above and below the presented condition e All other conditions lighter or darker cause the output to change state e Sensing window center can be adjusted using and Navigation key Manual Adjust e Recommended for applications where a product may not always appear in the same place or when other signals may appear e See Program Mode in the user s manual for programming the Offset Percent setting to increase decrease the window size A single sensing condition is presented and the sensor positions window thresholds a programmable offset above and below the presented condition In LO mode Window SET designates a sensing window with the Output ON condition inside the window and the Output OFF conditions outside the window see Fig 4 Sensing window center adjusted by Manual Adjust Sensor positions window thresholds aprogrammable offset from the presented condition Output ON Darkest Condition Most Light no signal Presented saturated signal Figure 4 Window SET Light Operate shown Output ON and OFF conditions can be reversed using the LO DO switch see LO DO Switch in Top Panel Interface 7 See Troubleshooting on page 16 for more explanation of t
20. splay driven programming menu During ADJ mode SET is used to perform TEACH SET methods and are used to manually adjust the threshold s The Navigation key is disabled during RUN mode except when using Window SET see Window SET HEO tea Red Green Digital Displays During RUN and ADJ mode the Red display shows the signal level and the Green display shows the threshold During PRG mode both displays are used to navigate the display driven programming menu Output LED The output LED provides a visible indication when the output is activated Remote Input IO Link For more information about how to perform TEACH SET methods to program the sensor remotely or to interface with the sensor via O Link see the www datalogic com Run Mode Run mode allows the sensor to operate normally and prevents unintentional programming changes The SET Navigation key is disabled during RUN mode except when using Window SET see Window SET PROGRAMMODE t gt To scroll through menu lists Press or To enter a choice list or to select and save Click SET To exit a choice list without saving Press and hold SET for 2 seconds Mode Switch to PRG Navigation key Menu List diSP rEAd L Return to Menu List Click SET Click SET Click SET Click SET Click SET Click SET Click SET Click
21. ust Sensor positions threshold a programmable offset below the lt q presented condition Output OFF Output ON Darkest Condition Most Light no signal Presented saturated signal Figure 6 Light SET Light Operate shown Light SET and Manual Adjust Moves switching threshold value up or down to make adjustments e Slide Mode switch to ADJ to enter Adjust mode e Press to increase press to decrease GREEN display shows the switching threshold value 2 seconds after adjustment the GREEN display will flash 3 times to confirm e Slide Mode switch to RUN to complete operation Remember Manual adjustments are disabled when Auto Thresholds are ON Follow these steps to perform a Light SET Note TEACH Selection must be programmed to Lt SEt see Program Mode 1 Enter Adjust Mode Method Action Result SET Button H Set Mode switch to ADJ RUN PRG ADJ Display Red Signal Level Green Threshold A Remote Inpu No action is required sensor is ready for Light SET method 11 SET Button 0 04 seconds lt Click lt 0 8 seconds 12 Remote Input 0 04 seconds lt T lt 0 8 seconds 11 DATALOGIC 2 SET Sensing Condition Method Action Result e Present sensing condition SET Button l Eee RUN PRG ADJ Threshold Condition Accepted e Click the SET Navigation key Displays read Lt SEt then alternate PASS with Offset 3 Sensor returns to Adjust mode e Present sensing condition T Rem
Download Pdf Manuals
Related Search