DSTni-XPress DR Quick Start
Contents
1. network See the user manual for troubleshooting network problems From the Ping Device window you can ping devices not listed in the main window by entering a new address in the IP address field DSTni XPress DR IAP devices allow you to install a protocol such as MODBUS Bridge for your automation application Skip Step 5 if you have a DSTni XPress DR Step 5 Upgrade the Firmware ae Click the Upgrade Firmware icon Pa The Upgrade Firmware window displays The IP address displays in the first field Select the current protocol using the list button in the Existing Firmware field factory default IAP Standard Tunnel Click the open file icon next to the FW File field A list of firmware files displays Use the search buttons to locate the firmware files on the CD or downloaded files from the Lantronix support web page Looki GaFimware la DF1 Multi master ad0100 rom a Itx45 rorn a mod12 rom a Standard Tunnel aq0100 rom File name Amo1 44 Files of type ROM Files ROM Cancel Open as read only Select the desired protocol and click Open The selected file and path displays in the FW File field Click Upgrade FW File The File upgrade successful message displays Click OK and close the upgrade firmware window Step 6 Configure the Device To view or update the Device Server configuration use the Device Management window to open a Telnet connection 1 Click the Device Management ic2. DSTni XPress DR Quick Start DSTni XPress DR DR I AP DSTni XPress DR and DSTni XPress DR IAP are members of the Lantronix family of Device Servers DSTni XPress DR IAP devices allow you to install the protocol suitable for your automation application When you complete the setup you can Ethernet enable a serial device by connecting it to the serial port See the DSTni XPress DR User Guide on the software CD Quick Connect Reset Switch gt n haea 4 RJ45 Serial Port o RS 232 amp RS 422 485 Serial exe q Transmit Active LED RS232 H RS485 amp Receive Active LED 10 100BASE T RS 232 or RS 485 422 amp E E 4 Strew Terminals for Ethernet Status LEDs RJ45 10 100BASE T gt Ethernet Port Select Switch 9 30VDC or 9 24VAC 1 Connect the XPress DR to the network through the Ethernet port The unit must be on the same network as your computer 2 Connect power 9 30VDC or 9 24VAC 3 Verify that the green Link LED is lit LANTRONIX Setup Follow these steps to quickly setup the device Step 1 Start Devicel nstaller 1 Insert the software CD into your CD ROM drive When the main window appears click the Device Installer button and follow the instructions on the screen 2 Click the Start button and then point to Programs Point to the folder that contains Device Installer then click Device Installer The Device Installer main window will appear St
3. ep 2 Assign an IP Address IP 1 Click the Assign IP icon I The Assign IP Address window displays nA Assign IP Address Target Enter the Hardware or Ethernet Address e g 00 20 44 14 01 18 00 20 44 72 46 71 Enter IP Address to assign decimal dot notation fi 92 168 100 077 Set IP Address m PCE Network Class ClassC subnet mask 255 255 255 0 C ClassB subnet mask 255 255 0 0 Back 2 Inthe Enter the Hardware or Ethernet Address field type the Ethernet address MAC address listed on the Device Server label on the right side of the unit 3 Inthe Enter IP Address to assign field type the IP address of the Device Server Xxx Xxx XXX XXX format Select a PC Network Class 4 Click the Set IP Address button The Assign IP Successful message displays Click OK Step 3 Search the Network 1 Click the Search Network icon The Search Network window displays 2 Click the Start Search button The message Response from XXX XXX XXX XXX appears in the window Click the Save button and a device saved message appears Click OK then the Back button The IP Address and Hardware Address appear in the window 900 289 Rev B Step 4 Pinging Devices L From the main Devicelnstaller window select the installed device from the list then click the Ping Device icon A reply from the selected device indicates an active device An error message indicates a problem with the
4. on ip Click the Telnet to Device icon 2 When the Telnet window opens you have 5 seconds to press the Enter key 3 Note the firmware code and description on the first few lines 4 Review and edit the settings to match your application When done enter S to save the changes and Q to Quit Step 7 Connecting Serial Devices The cable below is a typical PC COM1 to DSTni XPress DR cable using the serial RJ 45 connector You can use the serial port to configure and test the port settings prior to connection to your automation device 4 DTR Out 1 No Connection 6 DSR 2 DTR Out 3 TxD Ou 3 RXD in 2 PXD n 4 TXD Ou _5 Signal Ground _ 5 Signal Ground 6 CTS n 8 CTS m EE 8 No Connection DTE 9 Pin FEMALE SERIAL RJ 45 View from Connector End DTE 9 Pin FEMALE SERIAL RJ 45 The following cable connects a typical PC COM1 to the DSTni XPress DR through the serial screw terminals LANTRONIX DTE 9 PIN FEMALE DTE 9 PIN FEMALE
Download Pdf Manuals
Related Search